Philips FC8778/01 Instrukcja obsługi

FC8778

300001532021

1 sec.

1 x

3 sec.

10 sec.

20 sec.

1

2

3

4

5

6

7

8

9 10

12

13

14

15

18

19

2021

17

11

16

English 6

Magyar 23

Polski 40

Slovenščina 59

Русский 76

Қазақша

94

English

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit

from the support that Philips offers, register your product at

www.philips.com/welcome.

General description (Fig. 1)

1 Top cover

2 Handle of dust container lid

3 Dust container lid

4 Filter

5 Dust container

6 Fan

7 Bumper

8 Docking station sensor

9 Start/stop button

10 Display

11 TriActive XL nozzle

12 Front wheel

13 Side brush shafts

14 Drop-off sensors

15 Battery compartment

16 Wheels

17 Suction opening

18 Side brushes

19 Small plug

20 Adapter

21 Docking station

Display

Display:

1 2

1 Warning indicator

2 WiFi connection indicator

How your robot works

What your robot cleans

This robot is equipped with features that make it a suitable cleaner to help

you clean the floors in your home.

The robot is especially suitable for cleaning hard floors, such as wooden,

tiled or linoleum floors. It may experience problems cleaning soft floors,

6

English

such as carpet or rugs. If you use the robot on a carpet or rug, please stay

close by the first time to see if the robot can deal with this type of floor. The

robot also needs supervision when you use it on very dark or shiny hard

floors.

How your robot cleans

Cleaning system

The robot has a 2-stage cleaning system to clean your floors efficiently.

-

The two side brushes help the robot clean in corners and along walls.

They also help to remove dirt from the floor and move it towards the

suction opening.

-

The suction power of the robot picks up loose dirt and transports it

through the suction opening into the dust container.

Cleaning patterns

In its auto cleaning mode, the robot uses an automatic sequence of cleaning

patterns to clean each area of the room optimally. The cleaning patterns it

uses are:

1 Z-pattern or zigzag pattern

2 Random pattern

7

English

3 Wall-following pattern

4 Spot-cleaning pattern

In its auto cleaning mode, the robot uses these patterns in a fixed

sequence:z-pattern, random pattern, wall-following pattern, and spot-

cleaning pattern.

When the robot has completed this sequence of patterns, it starts moving in

Z-pattern again. The robot continues to use this sequence of patterns to

clean the room until the rechargeable battery runs low, or until it is switched

off manually.

Note: You can also select each mode individually in the app.

How your robot avoids height differences

The robot has three drop-off sensors in its bottom. It uses these drop-off

sensors to detect and avoid height differences such as staircases.

Note: It is normal for the robot to move slightly over the edge of a height

difference, as its front drop-off sensor is located behind the bumper.

Caution: In some cases, the drop-off sensors may not detect a staircase or

other height difference in time. Therefore monitor the robot carefully the

first few times you use it, and when you operate it near a staircase or

another height difference. It is important that you clean the drop-off

sensors regularly to ensure the robot continues to detect height

differences properly (see chapter ' Cleaning and maintenance' for

instructions).

Before first use

Mounting the side brushes

1 Unpack the side brushes and place the robot upside down on a table or

on the floor.

8

English

2 Push the side brushes onto the shafts on the bottom of the robot.

Note: Make sure you attach the side brushes properly. Press them onto

the shaft until you hear them lock into position with a click.

Preparing for use

Installing the docking station

1

2

1 Insert the small plug of the adapter into the socket on the docking station

(1) and insert the adapter into the wall socket (2).

2 Place the docking station on a horizontal, level floor against a wall.

100cm

30cm

80

cm

Note: Make sure that there are no obstacles or height differences 80 cm

in front, 30 cm to the right and 100 cm to the left of the docking station.

Important note: deep sleep mode

In deep sleep mode, the robot does not respond at all when you press a

button. To reactivate the robot when it is in deep sleep mode:

1 sec.

3 sec.

1 Press the start/stop button on the robot for one second to switch the

robot from deep sleep mode to standby mode.

2 Press the start/stop button on the robot briefly or press the start button

in the app to start cleaning.

3 If the robot does not start cleaning, place it on the plugged-in docking

station to recharge its rechargeable battery.

The robot enters deep sleep mode when you press the start/stop button for

3 seconds. It may also enter the deep sleep mode when its battery is empty.

The battery may, for instance, run empty if the robot is unable to find its

docking station.

9

English

Note: You cannot get the robot out of its deep sleep mode with the

start/stop button in the app, press the start/button on the robot.

Charging

-

When charging for the first time and when the rechargeable battery of

the robot is empty, the charging time is four hours.

-

When the rechargeable battery is fully charged, your robot can clean for

up to 120 minutes.

-

Your robot can only be charged on the docking station.

Charging automatically during use

1 When the robot has finished cleaning or when only 15% of the battery

power remains, it automatically searches for the docking station to

recharge. When the robot searches for the docking station, the start/stop

button flashes quickly.

2 When the rechargeable battery is fully charged, the start/stop button

lights up continuously.

Note: The robot only searches for the docking station automatically when it

started cleaning from the docking station.

Charging on the docking station

1 Press the start/stop button on the robot.

2 Place the robot on the plugged-in docking station.

3 The start/stop button starts flashing slowly.

10

English

4 When the rechargeable battery is fully charged, the start/stop button

lights up continuously.

Setting up the WiFi connection

1 Search for 'Philips SmartPro' in the Apple App Store or in the Google Play

Store.

2 Download and install the Philips SmartPro app.

SmartPro

Connect to

your robot

Connect

Don’t own a robot yet?

FC8830/FC8832/FC8932

Buy one!

3 Open the app and press the 'Connect' button.

4 Press the start/stop button on the robot for 10 seconds to switch on the

robot and activate the WiFi setup mode and the user interface of the

robot. The WiFi setup is active if the WiFi connection indicator flashes

orange.

SmartPro

Already connected? Choose your Robot below...

Connect your robot

Start demo mode

5 Press 'Connect your robot'.

Follow these 4 easy steps to connect

your Philips robot vacuum cleaner to

your home wiFi and pair with your

phone.

For a successful WiFi connection, position the Philips

Robot vacuum cleaner within reach of your router.

Obstacles such as walls may aect the WiFi

performance. It is advised to to use a WPA2 secured

Wi-Fi network.

GET STARTED

Easy WiFi setup

6 Press ‘Get started’ and follow the on-screen instructions on the display.

There are four steps.

7 The WiFi connection indicator lights up solid blue when the WiFi

connection has been established.

11

English

“I’m waiting for a command”

DemoRVC

“I’ll clean for 90 minutes”

60 m

2

or more

Dry wipe: OFF

Combine modes

Clean Settings

Start cleaning

Return to charging base

Dashboard

8 The robot is connected when you see the robot in the screen of your app.

This will look like the picture on the left.

What to do if WiFi setup fails

If no WiFi connection is established after 1 minute, the appliance enters

access point mode and waits for a new attempt to set up the connection.

For iPhones:

1 Open settings, choose 'Wi-Fi' and select 'PHILIPS Setup'.

2 Select the access point starting with 'PHILIPS Setup'.

3 Go back to the Philips SmartPro app and click 'Next' to set up the WiFi

connection.

Android smartphones:

1 Go to 'Settings' and tap WiFi.

2 Select 'PHILIPS Setup'.

3 Go back to the Philips SmartPro app and click 'Next' to set up the WiFi

connection.

WiFi specifications

-

The robot is designed to be connected to standard consumer routers

that use WEP, WPA-PSK, WPA2-PSK encryption keys, or no encryption

(open WiFi network).

-

Connecting the robot to public hotspots, office networks or hotel

networks is not possible in most cases.

-

The robot will not work with 5 GHz routers. If you encounter problems

with connecting the robot to the router, please check if your router can

also be changed to the 2.4 GHz setting.

Using your robot

Preparing the room for a cleaning run

Before you start the robot on its cleaning run, make sure that you remove all

loose and fragile objects from the floor.

Also remove all cables, wires and cords from the floor.

Functions of the start/stop button

The start/stop button has 5 functions:

12

English

1 sec.

1 x

3 sec.

10 sec.

20 sec.

How you press start/stop button How robot responds

Press start/stop button for 1 second Robot switches from sleep mode to standby

Press start/stop button briefly Robot starts or stops cleaning

Press start/stop button for 3 seconds Switches robot on or off.

Press start/stop button for 10 seconds Activates WiFi setup and user interface on robot.

Press start/stop button for 20 seconds Resets WiFi connection. You hear two long beeps.

Activates WiFi setup and user interface.

User interface signals and their meaning

The robot has a display with two indicators: a warning indicator and the WiFi

connection indicator. The start/stop button gives light signals. The table

below explains the meaning of the signals.

Signal Description of signal Meaning of signal

The start/stop button is on continuously. The robot is ready to clean.

The start/stop button flashes slowly. The robot is charging.

The start/stop button flashes quickly. The robot is is searching for the

docking station.

The rechargeable battery of the robot

is low.

The WiFi connection indicator flashes slowly. The robot is in WiFi setup mode. The

robot does not yet have connection

with the smartphone and the WiFi

router.

The WiFi connection indicator flashes quickly. The robot is paired with the

smartphone but is not yet connected

with the WiFi router.

The WiFi connection indicator flashes twice briefly

at intervals.

The robot is connecting with the WiFi

router.

13

English

Signal Description of signal Meaning of signal

The WiFi connection indicator is solid blue. The WiFi connection with the robot

has been successfully established.

The warning indicator lights up. At the same time,

you receive a push notification in the app telling

you more about the issue.

The robot was lifted while it was

cleaning.

A wheel or side brush is stuck.

The bumper of the robot is stuck.

The top cover is not present or is not

closed properly.

The robot cannot find the docking

station.

Clap response

If you do not see the robot, you can locate it by clapping your hands once.

The robot will respond by beeping and by lighting up all icons on its display.

The clap response is enabled when the robot enters sleep mode in the

following situations:

-

when it stops cleaning due to an error

-

when it is unable to find its docking station within 20 minutes

.

Cleaning and maintenance

Emptying and cleaning the dust container

Empty and clean the dust container when the app shows that the dust

container is full.

1 Remove the cover.

2 Pull up the handle of the dust container lid and lift the dust container out

of the dust container compartment.

Note: When you remove or reinsert the dust container, take care not to

damage the blades of the motor fan.

14

English

2

1

3 Carefully lift the lid off the dust container (1) and take out the filter (2).

4 Shake the dust container over a dustbin to empty it. Clean the filter and

the inside of the dust container with a cloth or a toothbrush with soft

bristles. Also clean the suction opening in the bottom of the dust

container.

Caution: Do not clean the dust container and the filter with water or in

the dishwasher.

1

2

5 Put the filter back into the dust container (1). Then place the lid on the

dust container(2).

6 Put the dust container back into the dust container compartment and

put the top cover back on the robot.

Caution: Always make sure the filter is present inside the dust

container. If you use the robot without the filter inside the dust

container, the motor will be damaged.

15

English

Cleaning the robot

To maintain good cleaning performance, you have to clean the drop-off

sensors, the wheels, the side brushes and the suction opening from time to

time.

1 Place the robot upside down on a flat surface.

2

1

3

4

2 Use a brush with soft bristles (e.g. a toothbrush) to remove dust or fluff

from the drop-off sensors.

Note: It is important that you clean the drop-off sensors regularly. If the

drop-off sensors are dirty, the robot may fail to detect height differences

or staircases.

1

2

3

3 Use a brush with soft bristles (e.g. a toothbrush) to remove dust or fluff

from the front wheel and side wheels.

4 To clean the side brushes, grab them by the bristles and pull them off

their shafts.

5 Remove fluff, hairs and threads from the shaft and from the side brush

with a soft brush (e.g. a toothbrush) or a cloth.

Tip: If bristles of the side brushes are crooked or bent, soak the side

brushes in warm water for a while. If this does not restore the bristles to

their proper shape, replace the side brushes (see 'Replacing the side

brushes').

6 Check the side brushes and the bottom of the robot for any sharp

objects that could damage your floor.

16

English

7 After you have removed the side brushes from their shafts, undo the

snap connections of the TriActive XL nozzle by inserting your fingers at

the places marked with arrows and pull the TriActive nozzle off the robot.

8 Clean the suction opening with a soft brush (e.g. a toothbrush).

9 Remove all visible dirt from the TriActive nozzle.

10 Insert the snap hooks of the TriActive nozzle into the holes in the bottom

of the robot. Push the TriActive nozzle back into position. Make sure that

the TriActive nozzle can move a few millimeters up and down freely. If the

TriActive nozzle cannot move freely, disassemble it again and then

reassemble it carefully.

Replacement

Ordering accessories

To buy accessories or spare parts, visit www.philips.com/parts-and-

accessories or go to your Philips dealer. You can also contact the Philips

Consumer Care Center in your country (see the international warranty leaflet

for contact details).

17

English

Replacing the filter

Replace the filter if it is very dirty or damaged. You can order a new filter

under order number FC8012. See 'Emptying and cleaning the dust container'

in chapter 'Cleaning and maintenance' for instructions on how to remove the

filter from the dust container and how to place it in the dust container.

Replacing the side brushes

Replace the side brushes after some time to ensure proper cleaning results.

Note: Always replace the side brushes when you notice signs of wear or

damage. We also recommend that you replace both side brushes at the

same time. You can order spare side brushes as a set under order number

FC8013.

1 To replace the side brushes, grab the old side brushes by the bristles and

pull them off their shafts.

2 Push the new side brushes onto the shafts.

Replacing the rechargeable battery

The rechargeable battery of the robot may only be replaced by qualified

service engineers. Take the robot to an authorized Philips service center to

have the battery replaced when you can no longer recharge it or when it

runs out of power quickly. You can find the contact details of the Philips

Consumer Care Center in your country in the international warranty leaflet or

on the website at www.philips.com/support.

Warranty and support

If you need information or support, please visit www.philips.com/support or

read the international warranty leaflet.

Your robot vacuum cleaner has been designed and developed with the

greatest possible care. In the unfortunate case that your robot needs repair,

the Consumer Care Centre in your country will help you by arranging any

18

English

necessary repairs in the shortest possible time and with maximum

convenience. If there is no Consumer Care Centre in your country, go to your

local Philips dealer.

Recycling

-

This symbol means that this product shall not be disposed of with normal

household waste (2012/19/EU).

-

This symbol means that this product contains a built-in rechargeable

battery which shall not be disposed of with normal household waste

(2006/66/EC). Please take your product to an official collection point or

a Philips service center to have a professional remove the rechargeable

battery.

-

Follow your country’s rules for the separate collection of electrical and

electronic products and rechargeable batteries. Correct disposal helps

prevent negative consequences for the environment and human health.

Removing the rechargeable battery

Warning: Only remove the rechargeable battery when you discard

the appliance. Make sure the battery is completely empty when

you remove it.

To remove the rechargeable battery, follow the instructions below. You can

also take the robot to a Philips service center to have the rechargeable

battery removed. Contact the Philips Consumer Care Center in your country

for the address of a service center near you.

1 Start the robot from a place somewhere in the room and not from the

docking station.

2 Let the robot run until the rechargeable battery is empty to make sure

that the rechargeable battery is completely discharged before you

remove it and dispose of it.

1

2

3 Undo the screws of the battery compartment lid and remove the lid.

19

English

1

2

4 Lift out the rechargeable battery and disconnect it.

5 Take the robot and the rechargeable battery to a collection point for

electrical and electronic waste.

Troubleshooting

This chapter summarizes the most common problems you could encounter

with the appliance. If you are unable to solve the problem with the

information below, visit www.philips.com/support for a list of frequently

asked questions or contact the Consumer Care Center in your country.

Problem Possible cause Solution

The robot does not start

cleaning when I press the

start/stop button.

The rechargeable battery is

empty.

Charge the rechargeable battery (see

chapter 'Preparing for use').

The robot is in deep sleep

mode.

Press the start/stop button for one second

to reactivate the robot.When you press the

start/stop button briefly again, the robot

starts cleaning. If the rechargeable battery

is empty, the robot does not respond. In

that case, place the robot on the plugged-

in docking station.

The robot does not

respond when I press one

of the buttons.

The robot's rechargeable

battery is empty'.

Place the robot on the plugged-in docking

station. After a few seconds, the robot

beeps and the display lights up.

The warning indicator

flashes quickly. At the

same time, you receive a

push notification in the

app telling you more

about the issue.

One or both wheels are stuck. Remove the fluff, hair, thread or wire that

is caught around the wheel suspension.

One or both side brushes are

stuck.

Clean the side brushes (see 'Cleaning the

robot').

The top cover is not present

or is not closed properly.

When the top cover is not present or is not

closed properly, the robot does not work.

Place the top cover on the robot properly.

The bumper is stuck. Lift the robot so that its bumper comes

free. Place the robot at some distance

from the obstacle and press the start/stop

button briefly to make the robot resume

cleaning.

20

English

Problem Possible cause Solution

The robot was lifted while it

was cleaning.

Place the robot on the floor. Then press

the start/stop button briefly to make the

robot resume cleaning.

The robot does not clean

properly.

The bristles of one or both

side brushes are crooked or

bent.

Soak the brush or brushes in warm water

for a while. If this does not restore the

bristles to their proper shape, replace the

side brushes (see 'Replacing the side

brushes').

The filter in the dust

container is dirty.

Clean the filter in the dust container with a

cloth or a toothbrush with soft bristles. You

can also clean the filter and dust container

with a regular vacuum cleaner at a low

suction power setting.

If brushing or vacuuming does not help to

clean the filter, replace the filter with a

new one. We advise you to replace the

filter at least once a year.

The suction opening in the

bottom of the dust container

is clogged.

Clean the suction opening (see 'Cleaning

the robot').

The front wheel is jammed

with hair or other dirt.

Clean the front wheel (see 'Cleaning the

robot').

The robot is cleaning a very

dark or shiny surface, which

triggers the drop-off sensors.

This causes the robot to

move in an unusual pattern.

Press the start/stop button briefly and

then move the robot to a lighter colored

piece of the floor. If the problem continues

to occur on lighter colored floors, please

go to www.philips.com/support or contact

the Consumer Care Center in your country.

The robot is cleaning a floor

that reflects sunlight quite

strongly. This triggers the

drop-off sensors and causes

the robot to move in an

unusual pattern.

Close the curtains to block sunlight from

entering the room. You can also start

cleaning when the sunlight is less bright.

The rechargeable battery

can no longer be charged

or runs empty very fast.

The rechargeable battery has

reached the end of its life.

Have the rechargeable battery replaced by

a Philips service center (see 'Replacing the

rechargeable battery').

The robot is moving in

circles.

The robot is in spot-cleaning

mode.

This is normal behavior. The spot-cleaning

mode can be activated when a lot of dirt is

detected on the floor for a thorough clean.

It is also part of the auto cleaning mode.

After approximately one minute the robot

resumes its normal cleaning pattern. You

can also stop the spot-cleaning mode by

selecting a different cleaning mode in the

app.

21

English

Problem Possible cause Solution

The robot cannot find the

docking station.

There is not enough room for

the robot to navigate towards

the docking station.

Try to find another place for the docking

station (see 'Installing the docking station').

The robot is still actively

searching.

Give the robot around 20 minutes to

return to the docking station.

The robot was not started

from the docking station.

If you want the robot to return to the

docking station after a cleaning run, start it

from the docking station.

22

English

Strona jest ładowana ...

Philips FC8778/01 Instrukcja obsługi

Philips FC8778/01 Instrukcja obsługi

Powiązane dokumenty

Inne dokumenty