LD Systems STINGER G3 WMB 1 Instrukcja obsługi

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D`UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D‘ USO

STINGER

®

G3 INSTALLATION KITS

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

PREVENTIVE MEASURES 3-4

OVERVIEW 5-16

TECHNICAL DATA 17-18

MANUFACTURER’S DECLARATIONS 18

DEUTSCH

SICHERHEITSHINWEISE 19-20

ÜBERSICHT 21-32

TECHNISCHE DATEN 33-34

HERSTELLERERKLÄRUNGEN 34

FRANCAIS

MESURES PRÉVENTIVES 35-36

VUE D‘ENSEMBLE 37-47

CARACTÉRISTIQUES TECHNIQUES 47-49

DÉCLARATIONS DU FABRICANT 49

ESPAÑOL

MEDIDAS DE SEGURIDAD 50-51

VISTA GENERAL 52-63

DATOS TÉCNICOS 64-65

DECLARACIONES DEL FABRICANTE 66

POLSKI

ŚRODKI OSTROŻNOŚCI 66-67

PRZEGLĄD 68-79

DANE TECHNICZNE 80-81

OŚWIADCZENIA PRODUCENTA 81

ITALIANO

MISURE PRECAUZIONALI 82-83

PANORAMICA 84-95

DATI TECNICI 96-97

DICHIARAZIONI DEL PRODUTTORE 97

3

ENGLISH

YOU‘VE MADE THE RIGHT CHOICE!

We have designed this product to operate reliably over many years. LD Systems stands for this with its name and many years of experience

as a manufacturer of high-quality audio products. Please read this User‘s Manual carefully, so that you can begin making optimum use of

your LD Systems product quickly.

You can ﬁnd more information about LD-SYSTEMS at our Internet site WWW.LD-SYSTEMS.COM

PREVENTIVE MEASURES

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufﬁciently stable and compatible stands and/or mounts (for ﬁxed installations). Make certain that wall mounts are properly installed and

secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make certain that the equipment is always

installed so that is cooled sufﬁciently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Keep a minimum distance of 20 cm around and above the device.

12. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment - in this case, observe the

special instructions noted below. Do not expose this equipment to ﬂammable materials, ﬂuids or gases. Avoid direct sunlight!

13. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers ﬁlled with liquids, such as vases or

drinking vessels, on the equipment.

14. Make certain that objects cannot fall into the device.

15. Use this equipment only with the accessories recommended and intended by the manufacturer.

16. Do not open or modify this equipment.

17. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to tripping hazards.

18. During transport, make certain that the equipment cannot fall down and possibly cause property damage and personal injuries.

19. If your equipment is no longer functioning properly, if ﬂuids or objects have gotten inside the equipment or if it has been damaged in anot

her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by

authorized, qualiﬁed personnel.

20. Clean the equipment using a dry cloth.

21. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate plastic and paper/cardboard.

22. Plastic bags must be kept out of reach of children.

23. Please note that changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user´s authority

to operate the equipment.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS

24. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to an outlet with a protective

ground. Never deactivate the protective ground of a power cord.

25. If the equipment has been exposed to strong ﬂuctuations in temperature (for example, after transport), do not switch it on immediately.

Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

26. Before connecting the equipment to the power outlet, ﬁrst verify that the mains voltage and frequency match the values speciﬁed on the

equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the

mains power values match. If the included power cord or power adapter does not ﬁt in your wall outlet, contact your electrician.

27. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the mains outlet and/or power

adapter and the equipment connector.

28. When connecting the equipment, make certain that the power cord or power adapter is always freely accessible. Always disconnect the

equipment from the power supply if the equipment is not in use or if you want to clean the equipment. Always unplug the power cord and

power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter

with wet hands.

29. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this can shorten the useful life of

the equipment.

30. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repeatedly, please contact an

authorised service centre.

31. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter from the power outlet.

32. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be unlocked before it can be removed.

However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or

other damage. For this reason, always be careful when laying cables.

33. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or before extended periods of disuse.

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

4

CAUTION:

To reduce the risk of electric shock, do not remove cover (or back). There are no user serviceable parts

inside. Maintenance and repairs should be exclusively carried out by qualiﬁed service personnel.

The warning triangle with lightning symbol indicates dangerous uninsulated voltage inside the unit, which may cause an

electrical shock.

The warning triangle with exclamation mark indicates important operating and maintenance instructions.

Warning! This symbol indicates a hot surface. Certain parts of the housing can become hot during operation. After use, wait for

a cool-down period of at least 10 minutes before handling or transporting the device.

Warning! This device is designed for use below 2000 metres in altitude.

Warning! This product is not intended for use in tropical climates.

CAUTION! HIGH VOLUMES IN AUDIO PRODUCTS!

This device is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively applicable national

accident prevention rules and regulations. As a manufacturer, Adam Hall is obligated to notify you formally about the existence of potential

health risks.

Hearing damage due to high volume and prolonged exposure: When in use, this product is capable of producing high sound-pressure levels

(SPL) that can lead to irreversible hearing damage in performers, employees, and audience members. For this reason, avoid prolonged

exposure to volumes in excess of 90 dB.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Important: Before any assembly, check that all installation kit components are complete, undamaged and work correctly (split pins, screws,

bolts, nuts, locking pins, steel hooks, retaining sockets and threads in speakers, etc.). Should any installation kit component be damaged,

missing or not function properly, the installation kit should not be used.

An M8 thread is situated on the rear side of the speaker for the installation of a secondary safety component.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

5

OVERVIEW

Product number Suitable for Installation Type

LDEB82G3WMB LDEB82G3 LDEB82AG3

Wall & ceiling

LDEB102G3WMB LDEB102G3 LDEB102AG3

LDEB282G3WMB LDEB282G3 LDEB282AG3

LDEBG3WMB

LDEB122G3 LDEB122AG3

Wall, ceiling,

traverse

LDEB152G3 LDEB152AG3

LDEB82G3WMB1 LDEB82G3 Wall

LDEB82AG3WMB1 LDEB82AG3 Wall

&

GSPWMBS30B LDEB282G3 Wall

LDEB282AG3WMB1 LDEB282AG3 Wall &

LDEB102G3WMB1 LDEB102G3 LDEB102AG3 Wall

LDEBG3WMB1

LDEB122G3 LDEB122AG3

Wall

LDEB152G3 LDEB152AG3

LDEBG3TMB

LDEB122G3 LDEB122AG3

Truss

LDEB152G3 LDEB152AG3

LDEBG3SCP

LDEB82G3 LDEB82AG3

Truss

LDEB102G3 LDEB102AG3

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

6

C

A

B

A

LDEB82G3WMB (suitable for LDEB82G3, LDEB82AG3)

LDEB102G3WMB (suitable for LDEB102G3, LDEB102AG3)

LDEB282G3WMB (suitable for LDEB282G3, LDEB282AG3)

Screw the U-bracket of the desired Stinger G3 speaker in a suitable position to a load-bearing wall or ceiling (A). Use suitable screws and plugs etc.

to ensure secure mounting. Remove the M8 screws on the top and bottom of the speaker and lift the speaker into the bracket so that the thread

locations in the speaker and the holes in the bracket are aligned. Use the supplied M8 screws and washers as shown in the ﬁgure below (B, place

rubber washers between the bracket and the speaker), adjust dispersion angle as desired and tighten the screws with a suitable tool (C).

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

7

A

F

A

F

D

C

E

B

LDEBG3WMB (suitable for LDEB122G3, LDEB122AG3, LDEB152G3, LDEB152AG3)

Screw the adjustable U-bracket (in a suitable position) to a load-bearing wall or ceiling (A). Use suitable screws and plugs etc. to ensure secure

mounting. The 35mm mounting stud can be installed on the bracket at four different distances from the wall (or ceiling). Select the appropriate

position for the speaker and screw it tightly to the bracket (B, position the supplied rubber ring on the mounting stud). Remove the M10 screw

on the top of the loudspeaker and lift the speaker into the bracket so that the 35mm mounting stud sits in the 0° ﬂange of the speaker (C).

Now set the adjustable side of the bracket to the appropriate size for the speaker and secure it with the two screws on the side of the bracket

(D). Using the supplied M10 T-screw in the correct position directly opposite the mounting stud, position the speaker at the desired angle in

the bracket (E, place supplied rubber washer between bracket and speaker. For permanent installation an M10 Allen screw is supplied). For

traverse-installation, mounting holes for traverse clamps are situated at positions corresponding to speaker size (F).

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

8

A

LDEB82G3WMB1 (suitable for LDEB82G3)

1. Remove the two M6 screws A on the back of the speaker.

2. Slightly loosen bolt E on the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove it and lift the

U-bracket B from its mounting. Attach the U-bracket B to the rear of the speaker with the supplied screws.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (4

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket B into the bracket on the wall, reinstall bolt D into its designated position and secure it

with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

A

LDEB82AG3WMB1 (suitable for LDEB82AG3)

1. Remove four M4 screws A on the back of the speaker in the positions for fastening the adapter plate. Ensure that the cutouts for the LINE

OUT jack and POWER switch are correctly positioned. Attach the adapter plate to the speaker with the supplied M4 screws so that the LINE

OUT jack and POWER switch are freely accessible.

2. Slightly loosen bolt E on the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove it and lift the

U-bracket B from its mounting. Attach the U-bracket B to the rear of the adapter plate with the supplied nuts.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (4

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket B into the bracket on the wall, reinstall bolt D into its designated position and secure it

with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

9

B

D

E

F

C

GSPWMBS30B (suitable for LDEB282G3)

1. Remove the four M6 screws A on the back of the speaker.

2. Slightly loosen bolt E of the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove and lift the

U-bracket with mounting plate B from its mounting. Attach the U-bracket with mounting plate B to the rear of the speaker with the supplied

screws.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (8

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket with mounting plate B into the bracket on the wall, reinstall bolt D into its designated

position and secure it with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

10

E

D

B

F

A

LDEB282AG3WMB1 (suitable for LDEB282AG3)

1. Remove six M4 screws A on the back of the speaker in the positions for fastening the adapter plate. Ensure that the cutouts for the LINE

OUT jack and POWER switch are correctly positioned. Attach the adapter plate to the speaker with the supplied M4 screws so that the LINE

OUT jack and POWER switch are freely accessible.

2. Slightly loosen bolt E on the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove it and lift the

U-bracket B from its mounting. Attach the U-bracket B to the rear of the adapter plate with the supplied nuts.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (8

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket B into the bracket on the wall, reinstall bolt D into its designated position and secure it

with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

11

A

C

E

D

F

B

LDEB102G3WMB1 (suitable for LDEB102G3, LDEB102AG3)

1. Remove the four M6 screws A on the back of the speaker.

2. Slightly loosen bolt E of the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove and lift the

U-bracket with mounting plate B from its mounting. Attach the U-bracket with mounting plate B to the rear of the speaker with the supplied

screws.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (4

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket with mounting plate B into the bracket on the wall, reinstall bolt D into its designated

position and secure it with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

12

A

C

E

D

B

F

LDEBG3WMB1 (suitable for LDEB122G3, LDEB122AG3, LDEB152G3, LDEB152AG3)

1. Remove the four M6 screws A on the back of the speaker.

2. Slightly loosen bolt E of the wall bracket (do not remove), loosen and remove bolt D from the tilt & swivel arm, remove and lift the

U-bracket with mounting plate B from its mounting. Attach the U-bracket with mounting plate B to the rear of the speaker with the supplied

screws.

3. Using screws, attach mounting plate C vertically in a suitable position to a solid wall with its ﬂat side and safety eyelet facing upwards (8

screws). Use suitable screws and plugs etc. to ensure secure mounting.

4. Now slide the speaker with the attached U-bracket with mounting plate B into the bracket on the wall, reinstall bolt D into its designated

position and secure it with the previously removed nut.

5. The speaker can be tilted vertically by slightly loosening nut E, adjusting to the desired angle and then re-tightening the nut. The speaker can

be adjusted horizontally by loosening nut F (remove plastic cap beforehand), adjusting the angle as required, and then re-tightening the nut.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

13

LDEBG3TMB (suitable for LDEB122G3, LDEB122AG3, LDEB152G3, LDEB152AG3)

H

I

E

G

F

D

B

C

A

J

ASSEMBLY OF THE MOUNTING BRACKET AND TRAVERSE CLAMP

1. Release the safety splint (A) from the two M8 screws (B, C) in the cylindrical pivot/tilt head (D) of the mounting bracket.

2. Unscrew the two screws (B, C) from the pivot/tilt head (D), separate the two cylinder halves and remove the cast piece (E).

3. Now use the parts included – the M10 screw (F), spring washer (G) and self-locking M10 nut (H) – to attach the cast piece (E) ﬁrmly to

the traverse clamp (I) using a 17 mm socket tool. To do so, place the traverse clamp in the recess of the cast piece and the self-locking nut

in the recess of the traverse clamp and then insert the screw with the spring washer through the cast piece into the traverse clamp (see

illustration).

4. Now place the cast piece with the traverse clamp into one half of the pivot/tilt head (D) and join the two halves in such a way that the M8

screw (C) can be placed through the appropriate installation hole of the one half, through the support rail (J) of the mounting bracket and

through the installation hole of the cylindrical pivot/tilt head. Place the previously removed washer on the screw and ﬁnger tighten the M8

nut. Secure the nut using the previously released safety splint (A).

5. Put the M8 washer onto the M8 lever screw (B), taking care to ensure that the M8 nut is correctly placed in the recess of the appropriate

cylinder half of the pivot/tilt head. Insert the lever screw through the two cylinder halves and tighten. Secure the screw using a previously

released safety splint (A).

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

14

2

3

9

5

4

9

6

1

7

8

7

PARTS DESCRIPTION AND INSTALLATION

1

Traverse clamp for mounting on a horizontal traverse.

2

Wing nut for clamping to a traverse.

3

T-screw to lock the horizontal and vertical axes

4

Mounting rail with slots to adjust the vertical dispersion of the speaker.

5

Retaining pin.

6

Rotation mechanism for adjusting the horizontal dispersion of the speaker.

7

Three steel hooks which insert into the retaining sockets on the top of the speaker.

8

Two spring-loaded locking pins to secure the connection.

9

Mounting holes for alternative installation of the speaker with chains.

Important: Before any assembly, check that all mounting bracket components are complete, undamaged and work correctly (split pins,

screws, bolts, nuts, locking pins, steel hooks, retaining sockets in speakers, etc.). Should any mounting bracket component be damaged,

missing or not function properly, the mounting bracket should not be used.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

15

10 11 12

13 14 15

10

Insert all three steel hooks of the EasyMount bracket into the corresponding retaining sockets on the speaker.

11

Slide the entire bracket towards the back of the speaker.

12

When installing the mounting bracket, ensure that the spring-loaded locking pins engage fully. Ensure that locking pins are functioning

correctly before every installation. For safety reasons, both locking pins must be pulled upwards simultaneously to release the connection

(two-hand release).

13

Before attaching the speaker to a traverse, tighten the T-screw on the mounting bracket No. 3. Using traverse clamp No.1, suspend the

speaker from a horizontal traverse in a suitable position, and fasten it into place with wing nut No. 2.

14

Loosen T-screw No. 3 slightly (approximately 1 turn). To adjust the vertical dispersion of the speaker, lift the speaker slightly and slide

the notched mounting rail No.4 into the desired tilt position. Release the speaker to allow the retaining pin No. 5 to engage in the

corresponding notch.

15

Turn the speaker until the desired horizontal dispersion is achieved and tighten T-screw No. 3.

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

16

2

3

1

5

4

6

8

7

LDEBG3SCP (suitable for LDEB82G3, LDEB82AG3, LDEB102G3, LDEB102AG3)

1

Traverse clamp with adjustable T-screw and ﬂange for mounting pin (only for mounting on horizontal traverses).

2

Mounting pin with M10 thread and wing nut.

3

Adapter for attaching the clamp to square-section tubes.

4

Remove the M10 screw on the top of the speaker.

5

Remove the M10 wing nut from the mounting pin (No. 2) and screw it fully into the M10 thread on the top of the speaker.

6

Attach the traverse clamp to a traverse with the adjustable T-screw in a suitable position and ensure a ﬁrm grip.

7

Loosen the locking screw so far that the ﬂange on the underside of the clamp can accept the mounting pin (do not remove the bolt).

8

Push the spring-loaded locking pins on the side of the clamp into the housing so that the ﬂange on the underside of the clamp can

accept the mounting pin and push the pin all the way into the ﬂange. Release the pressure from the locking pin and keep hold of the

speaker until you are certain that the mounting pin is fully engaged. Rotate the speaker to achieve the desired dispersion and secure the

connection by tightening the locking screw No. 7.

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

17

Model name: LDEB82G3WMB LDEB102G3WMB

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Wall/Ceiling Mount Bracket Wall/Ceiling Mount Bracket

Suitable for: LDEB82G3, LDEB82AG3 LDEB102G3, LDEB102AG3

Material: Steel Steel

Surface: Powder Coated Powder Coated

Colour: Black Black

Max. Load 12 kg 15 kg

Dimensions (W x H x D): 60mm x 460mm x 170mm 60mm x 535mm x 170mm

Weight: 1.1 kg 1.2 kg

Model name: LDEB282G3WMB LDEBG3WMB

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Wall/Ceiling Mount Bracket Wall/Ceiling/Truss Mount Bracket

Suitable for: LDEB282G3, LDEB282AG3 LDEB122G3, LDEB122AG3

LDEB152G3, LDEB152AG3

Material: Steel Steel

Surface: Powder Coated Powder Coated

Colour: Black Black

Max. Load 21 kg 28 kg

Dimensions (W x H x D): 60mm x 763mm x 170mm 550mm x 90mm x 308mm

Weight: 1.5 kg 3.5 kg

Model name: LDEB82G3WMB1 LDEB82AG3WMB1

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Wall Mount Bracket Wall Mount Bracket

Suitable for: LDEB82G3 LDEB82AG3

Material: Steel Steel

Surface: Powder Coated Powder Coated

Colour: Black Black

Max. Load 20 kg 11 kg

Dimensions (W x H x D): 100mm x 157mm x 109mm 130mm x 157mm x 122mm

Weight: 1.2 kg 2.2 kg

Model name: GSPWMBS30B LDEB282AG3WMB1

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Wall Mount Bracket Wall Mount Bracket

Suitable for: LDEB282G3 LDEB282AG3

Material: Steel Steel

Surface: Powder Coated Powder Coated

Colour: Black Black

Max. Load 30 kg 21 kg

Dimensions (W x H x D): 120mm x 220mm x 160mm 130mm x 220mm x 173mm

Weight: 1.8 kg 3.3 kg

TECHNICAL DATA

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

18

Model name: LDEB102G3WMB1 LDEBG3WMB1

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Wall Mount Bracket Wall Mount Bracket

Suitable for: LDEB102G3, LDEB102AG3 LDEB122G3, LDEB122AG3

LDEB152G3, LDEB152AG3

Material: Steel Steel

Surface: Powder Coated Powder Coated

Colour: Black Black

Max. Load 20 kg 30 kg

Dimensions (W x H x D): 100mm x 157mm x 160mm 120mm x 220mm x 160mm

Weight: 1.4 kg 1.8 kg

Model name: LDEBG3TMB LDEBG3SCP

Type: PA Loudspeaker Accessories PA Loudspeaker Accessories

Part: Truss Mount Bracket Truss Mount Bracket

Suitable for: LDEB122G3, LDEB122AG3

LDEB152G3, LDEB152AG3

LDEB82G3, LDEB82AG3

LDEB102G3, LDEB102AG3

Material: Steel/Zinc Aluminium/Brass

Surface: Powder Coated Powder Coated/Uncoated

Colour: Black Black/Brass

Max. Load 28 kg 20 kg

Dimensions (W x H x D): 230mm x 240mm x 430mm 57mm x 136mm x 118mm

Weight: 3 kg 0.564 kg

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY

You can ﬁnd our current warranty conditions and limitations of liability at: https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Decla-

rations-LDSYSTEMS_DE_EN_ES_FR.pdf. To request warranty service for a product, please contact Adam Hall GmbH, Adam-Hall-Str. 1,

61267 Neu Anspach / Email: [email protected] / +49 (0)6081 / 9419-0.

CORRECT DISPOSAL OF THIS PRODUCT

(valid in the European Union and other European countries with a differentiated waste collection system)

This symbol on the product, or on its documents indicates that the device may not be treated as household waste. This is to avoid

environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste

and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased

this product, or their local government ofﬁce, for details on where and how they can recycle this item in an environmentally friendly manner.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed

with other commercial waste for disposal.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation

CE Compliance

Adam Hall GmbH states that this product meets the following guidelines (where applicable):

R&TTE (1999/5/EC) or RED (2014/53/EU) from June 2017

Low voltage directive (2014/35/EU)

EMV directive (2014/30/EU)

RoHS (2011/65/EU)

The complete declaration of conformity can be found at www.adamhall.com.

Furthermore, you may also direct your enquiry to [email protected].

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

DEUTSCH

SIE HABEN DIE RICHTIGE WAHL GETROFFEN!

Dieses Gerät wurde unter hohen Qualitätsanforderungen entwickelt und gefertigt, um viele Jahre einen reibungslosen Betrieb zu gewährleisten.

Dafür steht LD Systems mit seinem Namen und der langjährigen Erfahrung als Hersteller hochwertiger Audioprodukte. Bitte lesen Sie diese

Bedienungsanleitung sorgfältig, damit Sie Ihr neues Produkt von LD Systems schnell optimal einsetzen können.

Mehr Informationen zu LD SYSTEMS ﬁnden Sie auf unserer Internetseite WWW.LD-SYSTEMS.COM

SICHERHEITSHINWEISE

1. Lesen Sie diese Anleitung bitte sorgfältig durch.

2. Bewahren Sie alle Informationen und Anleitungen an einem sicheren Ort auf.

3. Befolgen Sie die Anweisungen.

4. Beachten Sie alle Warnhinweise. Entfernen Sie keine Sicherheitshinweise oder andere Informationen vom Gerät.

5. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.

6. Verwenden Sie ausschließlich stabile und passende Stative bzw. Befestigungen (bei Festinstallationen). Stellen Sie sicher, dass Wandhalterungen

ordnungsgemäß installiert und gesichert sind. Stellen Sie sicher, dass das Gerät sicher installiert ist und nicht herunterfallen kann.

7. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.

8. Installieren und betreiben Sie das Gerät nicht in der Nähe von Heizkörpern, Wärmespeichern, Öfen oder sonstigen Wärmequellen. Sorgen

Sie dafür, dass das Gerät immer so installiert ist, dass es ausreichend gekühlt wird und nicht überhitzen kann.

9. Platzieren Sie keine Zündquellen wie z.B. brennende Kerzen auf dem Gerät.

10. Lüftungsschlitze dürfen nicht blockiert werden.

11. Halten Sie einen Mindestabstand von 20 cm seitlich und oberhalb des Geräts ein.

12. Betreiben Sie das Gerät nicht in unmittelbarer Nähe von Wasser. Bringen Sie das Gerät nicht mit brennbaren Materialien, Flüssigkeiten

oder Gasen in Berührung. Direkte Sonneneinstrahlung vermeiden!

13. Sorgen Sie dafür, dass kein Tropf- oder Spritzwasser in das Gerät eindringen kann. Stellen Sie keine mit Flüssigkeit gefüllten Behältnisse

wie Vasen oder Trinkgefäße auf das Gerät.

14. Sorgen Sie dafür, dass keine Gegenstände in das Gerät fallen können.

15. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und vorgesehenen Zubehör.

16. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

17. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder Unfälle, z. B. durch Stolperfallen zu vermeiden.

18. Achten Sie beim Transport darauf, dass das Gerät nicht herunterfallen und dabei möglicherweise Sach- und Personenschäden verursachen kann.

19. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegenstände in das Geräteinnere gelangt sind, oder das

Gerät anderweitig beschädigt wurde, schalten Sie es sofort aus und trennen es von der Netzsteckdose (sofern es sich um ein aktives Gerät

handelt). Dieses Gerät darf nur von autorisiertem Fachpersonal repariert werden.

20. Verwenden Sie zur Reinigung des Geräts ein trockenes Tuch.

21. Beachten Sie alle in Ihrem Land geltenden Entsorgungsgesetze. Trennen Sie bei der Entsorgung der Verpackung bitte Kunststoff und

Papier bzw. Kartonagen voneinander.

22. Kunststoffbeutel müssen außer Reichweite von Kindern aufbewahrt werden.

23. Sämtliche vom Benutzer vorgenommenen Änderungen und Modiﬁkationen, denen die für die Einhaltung der Richtlinien verantwortliche

Partei nicht ausdrücklich zugestimmt hat, können zum Entzug der Betriebserlaubnis für das Gerät führen.

BEI GERÄTEN MIT NETZANSCHLUSS

24. ACHTUNG: Wenn das Netzkabel des Geräts mit einem Schutzkontakt ausgestattet ist, muss es an einer Steckdose mit Schutzleiter

angeschlossen werden. Deaktivieren Sie niemals den Schutzleiter eines Netzkabels.

25. Schalten Sie das Gerät nicht sofort ein, wenn es starken Temperaturschwankungen ausgesetzt war (beispielsweise nach dem Transport).

Feuchtigkeit und Kondensat könnten das Gerät beschädigen. Schalten Sie das Gerät erst ein, wenn es Zimmertemperatur erreicht hat.

26. Bevor Sie das Gerät an die Steckdose anschließen, prüfen Sie zuerst, ob die Spannung und die Frequenz des Stromnetzes mit den auf

dem Gerät angegebenen Werten übereinstimmen. Verfügt das Gerät über einen Spannungswahlschalter, schließen Sie das Gerät nur an die

Steckdose an, wenn die Gerätewerte mit den Werten des Stromnetzes übereinstimmen. Wenn das mitgelieferte Netzkabel bzw. der mitgelie-

ferte Netzadapter nicht in Ihre Netzsteckdose passt, wenden Sie sich an Ihren Elektriker.

27. Treten Sie nicht auf das Netzkabel. Sorgen Sie dafür, dass spannungsführende Kabel speziell an der Netzbuchse bzw. am Netzadapter

und der Gerätebuchse nicht geknickt werden.

28. Achten Sie bei der Verkabelung des Geräts immer darauf, dass das Netzkabel bzw. der Netzadapter stets frei zugänglich ist. Trennen Sie

das Gerät stets von der Stromzuführung, wenn das Gerät nicht benutzt wird, oder Sie das Gerät reinigen möchten. Ziehen Sie Netzkabel und

Netzadapter immer am Stecker bzw. am Adapter und nicht am Kabel aus der Steckdose. Berühren Sie Netzkabel und Netzadapter niemals mit

nassen Händen.

29. Schalten Sie das Gerät möglichst nicht schnell hintereinander ein und aus, da sonst die Lebensdauer des Geräts beeinträchtigt werden könnte.

30. WICHTIGER HINWEIS: Ersetzen Sie Sicherungen ausschließlich durch Sicherungen des gleichen Typs und Wertes. Sollte eine Sicherung

wiederholt auslösen, wenden Sie sich bitte an ein autorisiertes Servicezentrum.

31. Um das Gerät vollständig vom Stromnetz zu trennen, entfernen Sie das Netzkabel bzw. den Netzadapter aus der Steckdose.

32. Wenn Ihr Gerät mit einem verriegelbaren Netzanschluss bestückt ist, muss der passende Gerätestecker entsperrt werden, bevor er entfernt

werden kann. Das bedeutet aber auch, dass das Gerät durch ein Ziehen am Netzkabel verrutschen und herunterfallen kann, wodurch Personen

verletzt werden und/oder andere Schäden auftreten können. Verlegen Sie Ihre Kabel daher immer sorgfältig.

33. Entfernen Sie Netzkabel und Netzadapter aus der Steckdose bei Gefahr eines Blitzschlags oder wenn Sie das Gerät länger nicht verwenden.

ITALIANOPOLSKIESPAÑOL

FRANCAISDEUTSCHENGLISH

19

ACHTUNG

Entfernen Sie niemals die Abdeckung, da sonst das Risiko eines elektrischen Schlages besteht. Im

Inneren des Geräts beﬁnden sich keine Teile, die vom Bediener repariert oder gewartet werden können.

Lassen Sie Wartung und Reparaturen ausschließlich von qualiﬁziertem Servicepersonal durchführen.

Das gleichseitige Dreieck mit Blitzsymbol warnt vor nichtisolierten, gefährlichen Spannungen im Geräteinneren, die einen

elektrischen Schlag verursachen können.

Das gleichseitige Dreieck mit Ausrufungszeichen kennzeichnet wichtige Bedienungs- und Wartungshinweise.

Warnung! Dieses Symbol kennzeichnet heiße Oberﬂächen. Während des Betriebs können bestimmte Teile des Gehäuses heiß

werden. Berühren oder transportieren Sie das Gerät nach einem Einsatz erst nach einer Abkühlzeit von mindestens 10 Minuten.

Warnung! Dieses Gerät ist für eine Nutzung bis zu einer Höhe von maximal 2000 Metern über dem Meeresspiegel bestimmt.

Warnung! Dieses Gerät ist nicht für den Einsatz in tropischen Klimazonen bestimmt.

ACHTUNG HOHE LAUTSTÄRKEN BEI AUDIOPRODUKTEN!

Dieses Gerät ist für den professionellen Einsatz vorgesehen. Der kommerzielle Betrieb dieses Geräts unterliegt den jeweils gültigen

nationalen Vorschriften und Richtlinien zur Unfallverhütung. Als Hersteller ist Adam Hall gesetzlich verpﬂichtet, Sie ausdrücklich auf mögliche

Gesundheitsrisiken hinzuweisen. Gehörschäden durch hohe Lautstärken und Dauerbelastung: Bei der Verwendung dieses Produkts können

hohe Schalldruckpegel (SPL) erzeugt werden, die bei Künstlern, Mitarbeitern und Zuschauern zu irreparablen Gehörschäden führen können.

Vermeiden Sie länger anhaltende Belastung durch hohe Lautstärken über 90 dB.

Wichtige Hinweise: Überprüfen Sie vor jeder Montage alle Komponenten des Installationszubehörs auf Vollständigkeit, Beschädigungen und

korrekte Funktion (Splinte für Schrauben, Schrauben, Muttern, Sperrbolzen, Stahlhaken, Haltebuchsen und Gewinde im Lautsprecher usw.).

Sollte eine Komponente des Installationszubehörs beschädigt sein, fehlen oder nicht korrekt funktionieren, darf das Installationszubehör nicht

verwendet werden.

Für die Anbringung einer Sekundärsicherung beﬁndet sich ein M8 Gewinde auf der Rückseite des Lautsprechers.

20

DEUTSCHFRANCAIS

ESPAÑOL

ENGLISH

ITALIANO POLSKI

Strona jest ładowana ...

LD Systems STINGER G3 WMB 1 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

LD Systems STINGER G3 WMB 1 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty