Bosch BasicDome Series Instrukcja obsługi

Bosch
Marka
Bosch
Model
BasicDome Series
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

BasicDome Series
Instruction Manual
EN Suspended Ceiling
Mount Backbox
Modules
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Important Safeguards
Bosch Security Systems | 15 May 2003
EN
|
2
Important Safeguards
1. Read and Retain Instructions - All safety and
operating instructions should be read before the unit
is operated. Follow all operating and use
instructions.
2. Heed Warnings - Adhere to all warnings on the
unit and in the operating instructions.
3. Attachments - Attachments not recommended by
the product manufacturer should not be used, as
they may cause hazards.
4. Accessories - Do not place this unit on an unstable
stand, tripod, bracket, or mount. The unit may fall,
causing serious injury to a person and serious
damage to the unit. Use only with a stand, tripod,
bracket, or mount recommended by the
manufacturer or sold with the product. Any
mounting of the unit should follow the
manufacturer's instructions and should use
a mounting accessory recommended by the
manufacturer.
An appliance and cart combination should be
moved with care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart
combination to overturn.
5. Power Sources - This unit should be operated only
from the type of power source indicated on the label.
If unsure of the type of power supply to use, consult
your dealer or local power company. For units
intended to operate from battery power or other
sources, refer to the operating instructions. This
equipment is to be isolated from the mains supply by
a limited power source as specified in EN60950.
6. Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines or
other electric light or power circuits or where it can
fall into such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching such power lines or
circuits as contact with them might be fatal. U.S.A.
models only - refer to the National Electrical Code
Article 820 regarding installation of CATV systems.
7. S ervicing - Do not attempt to service this unit
yourself as opening or removing covers may expose
you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
8. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
9. Safety Check - Upon completion of any service or
repairs to this unit, ask the service technician to
perform safety checks to determine that the unit is
in proper operating condition.
10.Coax Grounding - If an outside cable system is
connected to the unit, be sure the cable system is
grounded. U.S.A. models only--Section 810 of the
National Electrical Code, ANSI/NFPA No.70,
provides information with respect to proper
grounding of the mount and supporting structure,
grounding of the coax to a discharge unit, size of
grounding conductors, location of discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | FCC Information
Bosch Security Systems | 15 May 2003
EN
|
3
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules and ICES-003 of
Industry Canada. These limits are designed to provide
reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses and
radiates radio frequency energy, and if not installed
and used in accordance with the instruction manual,
may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference,
in which case the user will be required to correct the
interference at his expense.
Intentional or unintentional changes or modifications,
not expressly approved by the party responsible for
compliance, shall not be made. Any such changes or
modifications could void the user’s authority to operate
the equipment. If necessary, the user should consult the
dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by
the Federal Communications Commission, helpful:
H
ow to Identify and Resolve Radio-TV Interference
P
roblems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Safety Precautions
Bosch Security Systems | 15 May 2003
EN
|
4
Safety Precautions
Attention: Installation should be performed by qualified
service personnel only in accordance with the National
Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches
have power supplied to the unit whenever the power cord is
inserted into the power source; however, the unit is
operational only when the ON-OFF switch is in the ON
position. The power cord is the main power disconnect for
all units.
Cover Removal
24 VAC Units:
Do not exceed 30 VAC input. Voltage applied to the unit's power
input should not exceed 30 VAC. Normal input voltage is 24
VAC. User supplied wiring from 24 VAC supply to unit must be
in compliance with electrical codes (Class 2 power levels). Do not
ground 24 VAC supply at power supply terminals or at unit's
power supply terminals.
This equipment is to be isolated from the mains supply
by a limited power source as specified in EN60950.
220-240 V, 50 Hz Power Cords
220-240 V, 50 Hz power cords, input and output, must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
Sécurité
Attention : L’installation doit être exclusivement effectuée
par un technicien spécialisé conformément à la
réglementation du code national de l’électricité des États-
Unis (NEC) ou à la réglementation locale.
Coupure de l’alimentation. Les appareils avec ou sans
commutateur ON-OFF (marche-arrêt) sont alimentés dès
que le cordon d’alimentation est branché à la source
d’alimentation ; toutefois, les appareils disposant d’un
commutateur de marche-arrêt ne fonctionnent que lorsque
celui-ci est sur la position ON (marche). Le cordon
d’alimentation est l’organe de coupure principal de
l’alimentation pour tous les appareils.
Enlèvement du capot
Appareils 24 VCA:
Ne pas excéder 30 V c.a. La tension appliquée à l’entrée
d’alimentation de l’appareil ne doit pas excéder 30 V c.a. La valeur
normale de la tension d’entrée est 24 V c.a. Le circuit électrique
reliant l’alimentation 24 V c.a. à l’appareil doit être conforme aux
codes électriques (niveaux d’alimentation de classe 2). Ne pas mettre
l’alimentation 24 V c.a. à la masse au niveau des bornes de
l’alimentation ou de l’appareil.
Cet équipement doit être isolé de l’alimentation secteur par
une source de puissance limitée, conformément à la norme
EN60950.
Cordons d’alimentation 220-240 V, 50 Hz
Les cordons d’alimentation 220-240 V, 50 Hz, d’entrée ou de
sortie, doivent être conformes à la dernière version de la
publication IEC 227 ou IEC 245.
ATTENTION : POUR ÉVITER TOUT RISQUE
D’ÉLECTROCUTION, NE PAS OUVRIR LE BOÎTIER. IL
N’Y A PAS DE PIÈCES REMPLAÇABLES À L’INTÉRIEUR.
POUR TOUTE INTERVENTION, S’ADRESSER À UN
RÉPARATEUR PROFESSIONNEL COMPÉTENT.
L’éclair fléché dans un triangle équilatéral avertit
l’utilisateur de la présence d’une
« tension dangereuse » non isolée à l’intérieur de
l’appareil et d’une valeur suffisante pour constituer
un risque d’électrocution.
Le point d’exclamation contenu dans un triangle
équilatéral avertit l’utilisateur de la présence, dans
la documentation qui accompagne l’appareil,
d’importantes consignes d’utilisation et de
maintenance.
Warning: Removal of the cover should only be
performed by qualified service personnel - not user
serviceable. The unit should always be unplugged
before removing the cover and remain unplugged
while the is removed.
Avertissement : L’enlèvement du capot ne doit être
effectué que par un technicien spécialisé. Il n’y a
pas de pièces remplaçables ou réglables par
l’utilisateur. Il faut toujours débrancher l’appareil
avant d’enlever le capot et le laisser débranché
jusqu’à la remise en place du capot.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Safety Precautions
Bosch Security Systems | 15 May 2003
EN
|
5
Sicherheitshinweise
Achtung: Die Installation darf nur von qualifiziertem
Wartungspersonal gemäß dem National Electrical Code
oder den gültigen örtlichen Vorschriften durchgeführt
werden.
Abtrennen der Spannungsversorgung: Die
Spannungsversorgung zu Geräten mit und ohne Ein/Aus-
Schalter ist hergestellt, wenn das Netzkabel an eine
Netzsteckdose angeschlossen ist. Das Gerät ist jedoch nur
betriebsbereit, wenn der Ein/Aus-Schalter eingeschaltet ist.
Bei allen Geräten erfolgt das Abtrennen der
Spannungsversorgung über das Netzkabel.
Abnehmen des Gehäuses
Geräte für 24 V Wechselstrom:
30 V Wechselstrom nicht überschreiten. Die Spannung, die dem
Stromanschluss des Geräts zugeführt wird, darf 30 V Wechselstrom
nicht überschreiten. Die normale Eingangsspannung beträgt
24 V Wechselstrom. Die vom Benutzer vorzusehende
Verkabelung von einer 24-V-Wechselstromquelle zum Gerät muss
den elektrischen Vorschriften (Stromstärke der Klasse 2)
entsprechen. Die 24-V-Wechselstromversorgung nicht an den
Stromversorgungsklemmen der Stromquelle oder des Geräts erden.
Dieses Gerät muss durch ein Netzteil nach den Limited-
Power-Source-Vorschriften EN60950.
Netzkabel für 220–240 V/50 Hz
Netzkabel für 220–240 V/50 Hz, Eingang und Ausgang, müssen
den neuesten Versionen der IEC Publikation 227 oder IEC
Publikation 245 entsprechen.
VORSICHT: DAS GEHÄUSE ZUR VERMEIDUNG VON
ELEKTRISCHEN SCHLÄGEN NICHT ÖFFNEN. DAS
GERÄT ENTHÄLT KEINE VOM BENUTZER ZU
WARTENDEN TEILE. REPARATUREN NUR VON
FACHPERSONAL AUSFÜHREN LASSEN.
Das Blitzsymbol im gleichseitigen Dreieck soll den
Benutzer auf nicht isolierte “gefährliche Spannung”
im Produkt hinweisen, die ausreichend stark sein
kann, um die Gefahr von elektrischen Schlägen für
Menschen darzustellen.
Das Ausrufungszeichen im gleichseitigen Dreieck
soll den Benutzer auf wichtige Bedienungs- und
Wartungsanweisungen in der Dokumentation
hinweisen, die dem Gerät beiliegt.
Precauciones de Seguridad
Atención: La instalación debe realizarla personal
cualificado en cumplimiento estricto del código eléctrico
nacional (en el caso de los EE.UU.) o de los códigos
locales aplicables.
Para Desconectar la Alimentación: Unidades no
equipadas con interruptores ON/OFF, son alimentadas
cuando el cable de alimentación es conectado a la
corriente eléctrica. Las unidades equipadas con
interruptores son alimentadas de igual forma, pero
adicionalmente requieren que el interruptor esté
posicionado en ON. El cable de alimentación es el
medio principal de desconexión del equipo.
Retirada de la cubierta
Unidades de 24 V CA:
La corriente de entrada nunca debe sobrepasar 30 V CA. La
tensión aplicada a la entrada de la unidad no debe exceder de
30 V CA. La tensión de entrada normal es de 24 V CA. El
cableado suministrado por el usuario desde la fuente de
alimentación de 24 V CA hasta la unidad debe cumplir las
normativas eléctricas pertinentes (niveles de potencia de Clase 2).
No conectar a tierra la corriente de 24 V CA en los terminales de
la fuente de alimentación ni en los terminales de alimentación de
la unidad.
Este equipo debe estar aislado de la red eléctrica por
medio de una fuente de alimentación limitada, según se
especifica en EN60950.
Cables de alimentación de 220-240 V, 50 Hz
Los cables de alimentación de 220-240 V, 50 Hz, tanto en la entrada
como en la salida, deben cumplir las versiones más modernas de las
publicaciones IEC 227 o 245.
PRECAUCIÓN: PARA REDUCIR EL RIESGO DE
DESCARGA ELÉCTRICA, NO ABRA LAS TAPAS. EN
EL INTERIOR NO HAY NINGÚN COMPONENTE
REPARABLE POR EL USUARIO. LAS REPARACIONES
DEBE REALIZARLAS PERSONAL CUALIFICADO.
El símbolo de flecha en forma de rayo situado
dentro de un triángulo equilátero pretende alertar
al usuario de la presencia de “voltaje peligroso”
sin aislamiento dentro de la caja del producto, el
cual podría resultar de una magnitud suficiente
como para presentar un riesgo de descarga
eléctrica para las personas.
El punto de exclamación dentro de un triángulo
equilátero pretende alertar al usuario de la existencia
de instrucciones de funcionamiento y
mantenimiento (reparación) en la documentación
suministrada con el aparato.
Warnung: Das gehäuse darf nur von qualifiziertem
wartungspersonal abgenommen werden –
reparaturen durch den benutzer sind nicht möglich.
Vor dem Abnehmen des Gehäuses muss stets der
Stecker aus der Netzsteckdose gezogen werden und
bei abgenommenem Gehäuse abgezogen bleiben.
Aviso: la retirada de la cubierta sólo debe ser
realizada por personal de servicio cualificado. La
unidad no contiene piezas que pueda reparar el
usuario. La unidad debe ser desenchufada de la red
siempre antes de retirar la cubierta y permanecer
desconectada hasta que ésta vuelva a colocarse .
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Safety Precautions
Bosch Security Systems | 15 May 2003
EN
|
6
Veiligheidsmaatregelen
Attentie: De installatie dient alleen te worden uitgevoerd
door gekwalificeerd servicepersoneel en in
overeenstemming met de plaatselijk geldende
installatievoorschriften.
Onderbreken van de spanning. Units met of zonder
AAN/UIT-schakelaar, staan onder spanning zolang het
netsnoer is verbonden met de wandcontactdoos. De unit
is echter alleen bedrijfsklaar als de AAN/UIT-schakelaar
in de AAN-stand staat. Losnemen van het netsnoer is
voor alle units de belangrijkste manier om de spanning
te onderbreken.
Behuizing verwijderen
Apparaten voor 24 V wisselstroom
Sluit geen hogere spanning aan dan 30 V wisselspanning. De spanning
die op de voedingsingang van het apparaat wordt aangesloten, mag
nooit hoger zijn dan 30 V wisselspanning. De normale ingangsspanning
is 24 V wisselspanning. De door de gebruiker toegepaste
verbindingskabel tussen een voedingsbron met 24 V wisselspanning en
het apparaat moet voldoen aan de plaatselijk geldende voorschriften
voor elektrische bedrading (Spanningsniveaus Klasse 2). De 24 V
wisselstroomvoeding mag niet op het lichtnet (stopcontact) of de
netaansluiting van het apparaat worden geaard.
Deze apparatuur moet van het elektriciteitsnet worden
geïsoleerd door een stroombegrenzing zoals gespecificeerd
in EN60950.
Netvoedingskabels 220-240 V, 50 Hz
Netvoedingskabels 220-240 V, 50 Hz, voor ingangs- en
uitgangsspanning, moeten voldoen aan de voorschriften in de
meest recente uitgave van IEC publicatie 227 of IEC publicatie 245.
GEVAAR: OPEN DEZE BEHUIZING NIET, TENEINDE
HET RISICO VAN ELEKTRISCHE SCHOKKEN TE
VOORKOMEN. BINNENIN BEVINDEN ZICH GEEN
DOOR DE GEBRUIKER TE REPAREREN
ONDERDELEN. RAADPLEEG VOOR REPARATIE
GEKWALIFICEERD SERVICEPERSONEEL.
Het symbool van een bliksem met pijlpunt in een
gelijkzijdige driehoek is bedoeld om de gebruiker
te waarschuwen voor de aanwezigheid van een niet
geïsoleerde ‘gevaarlijke spanning’ binnen in de
behuizing van het product, die voldoende sterk kan
zijn om personen het risico van een elektrische
schok te geven.
Het symbool van een uitroepteken in een
gelijkzijdige driehoek is bedoeld om de gebruiker
te waarschuwen voor de aanwezigheid van
belangrijke bedienings- en onderhouds- (service-)
instructies in de documentatie die met het product
zijn meegeleverd.
Precauzioni
Precauzione: affidare l’installazione al solo personale
qualificato e nel rispetto del Codice elettrico nazionale
(USA) o dei codici locali pertinenti.
Scollegamento dell’alimentazione. Gli apparecchi con o
senza commutatori ON-OFF ricevono corrente tutte le
volte che il cavo di alimentazione è inserito nella presa di
forza; tuttavia, gli apparecchi muniti di commutatore ON-
OFF funzionano solo se quest’ultimo è in posizione ON. Il
cavo di alimentazione serve a scollegare dalla corrente tutti
gli apparecchi
.
Rimozione della copertura
Unità a 24 V CA
Non superare la potenza di ingresso di 30 V CA. La tensione
erogata all’ingresso di alimentazione dell’unità non deve superare i 30
V CA. La tensione d’ingresso normale è di 24 V CA. Un’unità
alimentata con corrente da 24 V CA deve essere conforme alle
normative elettriche stabilite in materia di livelli di potenza dalla Classe
2. Non fornire la messa a terra ad un alimentatore da 24 V CA tramite i
terminali di alimentazione o i terminali di erogazione della corrente
elettrica all’unità.
Quest’apparecchiatura deve essere isolata dalla rete elettrica
mediante l’uso di un alimentatore a corrente limitata,
secondo le specifiche esposte in EN60950.
Cavi di alimentazione a 220-240 V, 50 Hz
I cavi di alimentazione a 220-240 V, 50 Hz devono essere conformi
(ingresso e uscita) alle versioni più recenti della pubblicazione
IEC 227 o IEC 245.
ATTENZIONE: PER RIDURRE IL PERICOLO DI
SCOSSA ELETTRICA, NON APRIRE LE COPERTURE.
L’ I NTERNO NON CONTIENE COMPONENTI CHE
L’UTENTE PUÒ RIPARARE PERSONALMENTE.
RIVOLGERSI AL PERSONALE DI ASSISTENZA
QUALIFICATO PER QUALSIASI INTERVENTO DI
RIPARAZIONE..
Il simbolo triangolare di un fulmine con la punta
a freccia intende mettere in allerta l’utente
riguardo alla presenza di tensioni pericolose non
isolate all’interno del guscio dell’unità, che
potrebbero essere di intensità sufficiente per
costituire pericolo di elettrocuzione.
Il punto esclamativo racchiuso in un triangolo
equilatero intende avvisare l’utente in merito alla
presenza di importanti istruzioni operative e di
manutenzione nella documentazione di
accompagnamento all’unità.
Waarschuwing: De behuizing mag uitsluitend door
deskundig technisch personeel worden verwijderd –
reparatie door de gebruiker is niet mogelijk. De
netvoeding van het apparaat moet altijd worden
ontkoppeld voordat de behuizing wordt verwijderd
en dient ontkoppeld te blijven zolang de behuizing
niet opnieuw is aangebracht.
Avvertenza – La rimozione della copertura è di
competenza esclusiva del personale
qualificato. Accertarsi che l’unità sia
sempre scollegata dall’alimentazione
elettrica prima di togliere la copertura
e non ricollegarla senza richiudere tale copertura.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Safety Precautions
Bosch Security Systems | 15 May 2003
EN
|
7
Medidas de Segurança
Atenção: A instalação deve ser efectuada por pessoal de
assistência técnica qualificado, de acordo com o National
Electrical Code (Normas de Electricidade Nacionais) ou a
legislação local aplicável.
Desconexão da electricidade. Unidades com ou sem
interruptores ON-OFF são activadas sempre que o cabo
eléctrico for ligado a uma fonte de alimentação. No
entanto, a unidade fica operacional apenas quando o
interruptor ON-OFF se encontrar na posição ON. Para
desligar a electricidade em qualquer uma das unidades
deve ser utilizado o cabo eléctrico.
Remoção da tampa
Unidades de 24 VAC:
Não exceda 30 VAC à entrada. A tensão aplicada à entrada da
unidade não deve exceder 30 VAC. A tensão nominal à entrada é de
24 VA C. Os cabos de 24 VAC de alimentação da unidade, fornecidos
pelo utilizador, têm de estar em conformidade com os regulamentos
eléctricos (níveis de potência da classe 2). Não ligue a alimentação de 24
VAC à terra mediante os bornes de alimentação ou os bornes de
alimentação da unidade.
Este equipamento deve ser isolado da rede de alimentação
através de uma fonte de potência limitada, conforme
especificado da norma EN60950.
Cabos de alimentação de 220-240 V, 50 Hz
Os cabos de alimentação de 220-240 V, 50 Hz, de entrada e
saída, têm de estar em conformidade com as versões mais
recentes da publicação CEI 227 ou publicação CEI 245.
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE
ELÉCTRICO, NÃO ABRA AS TAMPAS. O INTERIOR
NÃO CONTÉM PEÇAS QUE NECESSITEM DE
MANUTENÇÃO. A MANUTENÇÃO DEVE SER
EFECTUADA POR PESSOAL DE ASSISTÊNCIA
TÉCNICA QUALIFICADO.
O símbolo do raio com a cabeça de uma seta
dentro de um triângulo equilátero serve para
alertar o utilizar para a presença de "corrente
eléctrica perigosa" não isolada no interior da
caixa do produto que pode ser suficiente para
dar origem a choques eléctricos.
O ponto de exclamação dentro de um triângulo
equilátero serve para alertar o utilizador para a
presença de instruções de funcionamento e
manutenção importantes na documentação fornecida
com o aparelho.
Zasady Bezpieczeństwa
Uwaga: Instalację urządzenia powinien wykonać tylko
wykwalifikowany personel, zgodnie z przepisami NEC lub
odpowiednimi przepisami miejscowymi.
Odłączanie zasilania. Urządzenia zarówno nie posiadające, jak i
posiadające wyłączniki ON-OFF znajdują się pod napięciem,
jeżeli tylko przewód zasilający jest połączony ze źródłem
zasilania. Jednakże urządzenie działa tylko wtedy, gdy wyłącznik
znajduje się w położeniu ON. Przewód zasilający jest głównym
odłącznikiem zasilania dla wszystkich rodzajów urządzeń.
Zdejmowanie pokrywy
Zasilanie 24 V:
Nie przekraczać napięcia wejściowego 30 V. Napięcie podawane na wejście
zasilania urządzenia nie powinno przekroczyć 30 V. Znamionowe napięcia
zasilania wynosi 24 V. Doprowadzenie napięcia zasilania 24 V należy
przeprowadzić zgodnie z obowiązującymi przepisami (poziom zasilania klasy
2). Nie uziemiać napięcia zasilania na zaciskach zasilacza sieciowego lub
urządzenia.
To urządzenie winno być odizolowane od głównej sieci zasilającej
za pomocą źródła zasilania o ograniczonej mocy, zgodnie z
EN60950.
Kable zasilające 220 –240 V, 50Hz
Kable zasilające 220-240 V, 50 Hz, oraz wejścia i wyjścia muszą być zgodne z
ostatnimi wersjami Publikacji 227 lub 245 IEC.
UWAGA: ZE WZGLĘDU NA
NIEBEZPIECZEŃSTWO PORAŻENIA PRĄDEM NIE
WOLNO OTWIERAĆ POKRYWY. W ŚRODKU NIE
MA ŻADNYCH ELEMENTÓW, KTÓRE MOGĄ BYĆ
NAPRAWIANE PRZEZ UŻYTKOWNIKA.
NAPRAWĘ NALEŻY POWIERZYĆ
AUTORYZOWANEMU PUNKTOWI
SERWISOWEMU.
Błyskawica ze strzałką wewnątrz trójkąta
równobocznego ma za zadanie zwrócić uwagę
użytkownika na obecność nieizolowanego
"niebezpiecznego napięcia" wewnątrz obudowy
urządzenia, o wielkości stwarzającej niebezpieczeństwo
porażenia prądem.
Wykrzyknik wewnątrz trójkąta równobocznego ma za
zadanie zwrócić uwagę użytkownika na ważne czynności,
związane z obsługą i konserwacją urządzenia,
zamieszczone w Instrukcji obsługi.
Avvertenza – La rimozione della copertura è di
competenza esclusiva del personale
qualificato. Accertarsi che l’unità sia
sempre scollegata dall’alimentazione
elettrica prima di togliere la copertura
e non ricollegarla senza richiudere tale copertura.
Avvertenza – La rimozione della copertura è di
competenza esclusiva del personale
qualificato. Accertarsi che l’unità sia
sempre scollegata dall’alimentazione
elettrica prima di togliere la copertura
e non ricollegarla senza richiudere tale copertura.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Contents
Bosch Security Systems | 15 May 2003
EN
|
8
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1 UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
1.1 Backbox Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2 SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.1 Environmental Air Space Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.2 Backbox Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.3 Ceiling Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.3.1 Backbox Module Mounting in Suspended Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4.4 Backbox Module Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.5 Installing Backbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.6 Connecting Power, Signal, and Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.6.1 Connecting Line Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4.6.2 Connecting Biphase Signal Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.6.3 Connecting the RS-232 Signal Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.6.4 Connecting Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
4.6.5 EMI/RFI Interference Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
5 MAINTENANCE/COMPONENT REPLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Unpacking
Bosch Security Systems | 15 May 2003
EN
|
9
1UNPACKING
Unpack carefully. This electromechanical equipment
should be handled carefully.
Ensure that the following items are included:
• G3BS unit
• Backbox
• Base Bracket Assembly
•Trim Ring (optional)
• Installation Instructions (this manual)
If the item appears to have been damaged in shipment,
replace it properly in its carton and notify the shipper.
If any items are missing, notify your Bosch Security
Systems, Inc. Sales Representative or Customer Service
Representative.
The shipping carton is the safest container in which the
unit may be transported. Save it for possible future use.
1.1Backbox Module
The G3BS Backbox Module houses the Camera
Module and includes a bracket assembly for mounting
onto a ceiling tile, trim rings for attractive appearance,
and an isolated power supply.
Model Rated Voltage Power at
Number Voltage Range Rated Voltage
G3BS 24 VAC 21 to 28 15 W
50/60 Hz
2SERVICE
If the unit ever needs repair service, the customer
should contact Bosch Security Systems, Inc. Service
Center for authorization to return and shipping
instructions.
Service Centers
U.S.A.: Phone: 800-366-2283 or 408-956-3895
fax: 800-366-1329 or 408-956-3896
e-mail:NationalServiceC[email protected].com
Canada: 514-738-2434
Europe, Middle East & Asia Pacific Region:
32-1-440-0711
For additional information,
see www.boschsecuritysystems.com.
3DIMENSIONS
Figure 1: Dimensional Outline (Camera Module
Assembled in Backbox)
4INSTALLATION
ATTENTION: Installation should be
performed by qualified service personnel only
in accordance with the National Electrical
Code or applicable local codes.
4.1 Environmental Air Space Information
The BasicDome system is suitable for use in environmental
air spaces or in an air handling plenum of a nonfire-resistant
ceiling.
4.2 Backbox Module
The module consists of a Backbox and a Base Bracket
Assembly (PHOTO 1). Wiring is via one entry hole
located in the side of the backbox. If conduit is not
used, a strain relief bushing is required in accordance
with the National Electrical Code or applicable local
codes.
Photo 1: AutoDome Assembly
99
3.9
164.1
6.46
175.9
6.93
190
7.5
135
5.3
16.0
0.63
mm
in
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Installation
Bosch Security Systems | 15 May 2003
EN
|
10
4.3 Ceiling Mounting
4.3.1 Backbox Module Mounting in Suspended
Ceiling
Mount the backbox in a suspended ceiling grid using
the existing ceiling tile as follows.
1. Locate the bracket assembly at desired location
(PHOTO 2). Loosen the securing screws (shown in
PHOTO 4) on the base bracket assembly enough to
retain suspension bars during handling but allowing
for adjustment during installation.
Photo 2: Ceiling Mounting (Top View)
2. Snap the bar clips over the ceiling rails (PHOTO 3).
Slide the base plate to desired position on top of
the tile.
Photo 3: Bracket Clip Fitting
3. Tighten the four (4) bracket screws located in each
corner (PHOTO 4).
Photo 4: Bracket Securing Screws
4. Secure the bracket assembly to an overhead
securing point using a safety cable (PHOTO 5).
Photo 5: Safety Cable Fitment
5. Cut a hole in the tile using the bracket as a
template (PHOTO 6).
Photo 6: Cutting the Tile
Suspension
Bars
Ceiling Base
Bracket
Ceiling Tile
x 4
x 4
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Installation
Bosch Security Systems | 15 May 2003
EN
|
11
4.4 Backbox Module Mounting
Mount the backbox into the installed bracket assembly
as follows.
1. Verify that the edge of the hole will support the
unit. If the edge is uneven or slightly too large,
attach the mounting ring as shown in PHOTO 7
and PHOTO 8. If the backbox fits correctly, go
directly to STEP 4.5.
Photo 7: Mounting Ring Fitment
2. Push the optional ring over the mounting box clips
(PHOTO 8).
Photo 8: Mounting Ring Securing
4.5 Installing Backbox
1. Push the backbox up through the hole in the ceiling
until the two (2) flexible clamps snap through the
opening (PHOTO 9).
Photo 9: Installing Backbox
2. Push the backbox into the hole until completely
flush (PHOTO 10).
Photo 10: Installed Backbox
3. Tighten the two (2) flexible clamp screws.
DO NOT OVER TIGHTEN (PHOTO 11).
Photo 11 Securing Backbox
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Installation
Bosch Security Systems | 15 May 2003
EN
|
12
4.6 Connecting Power, Signal, and Video
CAUTION: Before proceeding, disconnect
power from the cable to be installed into the
unit. Be sure that the unit is of the proper line
voltage type (24 VAC) for line power being
used.
1. Route the wires through the backbox connector
opening (PHOTO 12 and PHOTO 13).
Photo 12: Wire Installation
Photo 13: Wire Routing Fitment
2. Make applicable wiring connections in accordance
with Connecting Line Power, Connecting Biphase
Signal Cable, Connecting RS-232 Signal Cable, and
Connecting Video Cable (PHOTO 14 through
PHOTO 17).
Photo 14: Connector Installation
4.6.1 Connecting Line Power (See Wiring Chart)
Make power line connections to Power Connection as
follows:
1. Unplug the connector from the backbox.
2. Connect the 24 VAC wires to the appropriate
terminals on the connector (PHOTO 15) using a
flat-bladed screwdriver.
Photo 15: Power Connector
3. When power is applied, a red LED will light.
Wiring Chart
24 VAC, 40 VA Max
Wire Size Maximum Distance
mm
2
AWG m ft
118 75250
1.5 16 120 400
Biphase
24 VAC
Power
RS-232
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Installation
Bosch Security Systems | 15 May 2003
EN
|
13
4.6.2 Connecting Biphase Signal Code
Not applicable if data input is via RS-232 (see
SECTION 4.6.3).
1. Unplug the connector from the backbox.
2. Identify the (+) phase, (-) phase and GND wires.
Use only twisted, sheilded pair, Belden 8760 or
equivelent.
3. Connect the plus phase to the C+ terminal, the
minus phase to the C– terminal, and the shielding
ground of the cable to the GND terminal using a
flat-bladed screwdriver, (see PHOTO 15). The
Biphase shield should be grounded at one end only.
The recommended connection is at the signal
source.
4. Route and connect the biphase connector as shown
in PHOTO 16.
Photo 16: Connector Locations
5. Daisy Chain wiring: Connect the (+) of each of the
cables by inserting them both into the C+ terminal
on the terminal block. Connect the (-) of each of the
cables by inserting them both into the C- terminal
on the terminal block. Connect the GND of each of
the cables in a similar manner. A 110 OHM
RESISTOR MUST BE CONNECTED
BETWEEN THE BIPHASE (+) AND (-)
TERMINALS ON THE LAST CAMERA.
4.6.3 Connecting the RS-232 Signal Cable
Not applicable if data input is via Biphase (see
SECTION 4.6.2).
1. Unplug the connector (PHOTO 16) from the
backbox.
2. Identify the RxD phase, TxD phase, and GND
wires.
3. Connect the RxD phase to the RXD terminal, the
TxD phase to the TXD terminal, and the signal
ground to GND terminal marked GND using a flat-
bladed screwdriver. Note that the shield of the
cable should be left unconnected.
4. Route and connect the RS-232 connector as shown
in PHOTO 16.
4.6.4 Connecting Video Cable
Route and connect video cable to BNC connector
(PHOTO 16).
NOTE: Push all excess cable through the conduit
fitting or strain relief bushing. This will ensure that
excess wire in the backbox will not interfere with the
proper insertion of the camera module.
4.6.5 EMI/RFI Interference Protection
For added protection from Electromagnetic
Interference (EMI) or Radio Frequency Interference
(RFI), snap the provided ferrite around the power
cable as close to the control connector as possible
(PHOTO 17). This can be outside the backbox if
necessary due to space constraints.
Photo 17: Ferrite Placement
Power/Data
Connector
Video
Connector
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Maintenance
Bosch Security Systems | 15 May 2003
EN
|
14
5
MAINTENANCE/COMPONENT
REPLACEMENT
No special maintenance is required.
Occasionally dust may accumulate inside the housing
and coat the transparent dome/trim ring. In this case,
power the unit off and remove the dome so that it is
away from the camera. While using proper eye
protection, clean the dome by using clean compressed
air from a spray can, and microwave safe paper towels,
and reseat the dome.
CAUTION: Do not remove camera from
pan/tilt. Remove the entire receiver/driver,
pan/tilt, and camera assembly from the
AutoDome system to prevent damage to the
flexible cable and connector.
Suspended Ceiling Mount Backbox Modules | Instruction Manual | Notes
Bosch Security Systems | 15 May 2003
EN
|
15
© 2003 Bosch Security Systems GmbH
3935 890 36313 03-20 May 15 Data subject to change without notice.
Bosch Security Systems, Inc.
850 Greenfield Road
Lancaster, PA 17601 EE.UU.
Tel: 800-326-3270
Fax: 1-717-735-6560
www.boschsecuritysystems.com
Robert Bosch GmbH
Geschäftsbereich
Postfach 10 60 50
70049 Stuttgart
Te le fax (0711) 811-12 34
www.bosch.de/k
Bosch Security Systems B.V.
P.O. Box 80002
5600 JB Eindhoven
The Netherlands
Tele +31 40 27 80000
www.boschsecuritysystems.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Bosch BasicDome Series Instrukcja obsługi

Bosch
Marka
Bosch
Model
BasicDome Series
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty