Sony KF-50SX300K Instrukcja obsługi

Operating Instructions

GB

Before operating the TV, please read the “Safety Information”

section of this manual. Retain this manual for future reference.

Инструкции за използване

BG

Преди да използвате телевизора, прочетете раздела

"Информация за безопасността" на това ръководство.

Запазете това ръководство за бъдещи справки.

Návod k použití

CZ

Před zapnutím televizoru si prosím pozorně přečtěte část

"Bezpečnostní upozornění" v tomto návodu. Návod si uschovejte

i pro budoucí potřebu.

Kezelési utasítás

HU

Mielőtt elkezdené használni a televíziót, kérjük, olvassa el a jelen

kézikönyv "Biztonsági tudnivalók" c. szakaszát. Őrizze meg a

kézikönyvet későbbi használatra.

Instrukcja obsługi

PL

Przed przystąpieniem do eksploatacji telewizora należy

zapoznać się z rozdziałem "Informacje dotyczące bezpieczeństwa"

w niniejszej instrukcji. Prosimy o zachowanie niniejszej instrukcji

do wglądu w przyszłości.

Инструкция по эксплуатации

RU

Перед тем как включить телевизор, просим Вас ознакомиться с

разделом "Общие правила техники безопасности" настоящей

инструкции. Сохраняйте настоящую инструкцию на будущее.

R

4-096-858-42 (1)

LCD Colour TV

KF-42SX300K

KF-50SX300K

KF-60SX300K

3

GB

Introduction

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

Table of Contents

Introduction .......................................................................................................................................................... 3

Safety Information................................................................................................................................................ 4

Overview & Installation

Checking the Accessories Supplied...................................................................................................................... 6

Inserting Batteries into the Remote Control......................................................................................................... 6

Overview of Remote Control Buttons.................................................................................................................. 7

Overview of the TV Buttons ................................................................................................................................8

Connecting the Aerial and VCR...........................................................................................................................9

Stabilizing the TV set ........................................................................................................................................... 9

First Time Operation

Switching on the TV and Automatically Tuning ...............................................................................................10

TV Functions

Introducing and Using the Menu System .......................................................................................................... 12

The Picture Adjustment menu ..................................................................................................................... 13

The Sound Adjustment menu.......................................................................................................................14

The Features menu........................................................................................................................................16

Autoformat .............................................................................................................................................16

AV3 Output............................................................................................................................................ 17

Connection Guide...................................................................................................................................17

RGB Centring......................................................................................................................................... 17

The Set Up menu..........................................................................................................................................18

Language................................................................................................................................................18

Country................................................................................................................................................... 18

Auto Tuning...........................................................................................................................................18

Programme Sorting ................................................................................................................................ 18

Programme Labels .................................................................................................................................19

AV Preset...............................................................................................................................................19

Manual Programme Preset..................................................................................................................... 20

PAP (Picture And Picture).................................................................................................................................. 21

Teletext.................................................................................................................................................................. 22

NexTView...............................................................................................................................................................23

Additional Information

Connecting Equipment to the TV........................................................................................................................24

Viewing pictures from equipment connected to the TV......................................................................................25

Remote Control Configuration for VCR or DVD ...............................................................................................26

Optimum Viewing area .......................................................................................................................................27

Replacing the lamp..............................................................................................................................................28

Technical Specifications......................................................................................................................................30

PC Input Specifications.......................................................................................................................................31

Troubleshooting...................................................................................................................................................32

How to lift the TV ................................................................................................................................Back cover

• Buttons shaded white on the remote control show you

the buttons you have to press to follow the sequence

of the instructions.

• Informs you of the result of the instructions.

• Important information.

• Information on a feature.

• 1,2... Sequence of instructions.

Table of Contents

4

Never place the TV in hot, humid or

excessively dusty places. Do not

install the TV where it may be

exposed to mechanical vibrations.

For environmental and safety reasons, it

is recommended that the TV set is not

left in standby mode when not in use.

Disconnect from the mains. However,

some TVs may have features which

require they are left in standby. The

instructions in this manual will inform

you if this applies.

Safety Information

Do not open the cabinet and the rear cover

of the TV. Refer to qualified service

personnel only.

To prevent fire, keep inflammable

objects or naked lights (eg candles)

away from the TV.

Pull out the power lead by the plug.

Do not pull on the power lead itself.

Place the TV on a secure stable stand.

Never attempt to move the TV and stand

together -always move the TV and stand

separately. Do not place the TV on its

side or face up. Do not allow children to

climb on to it.

This set is to operate on a 220-240V AC

supply only. Take care not to connect

too many appliances to the same power

socket as this could result in fire or

electric shock.

To prevent fire or shock hazard, do not

expose the TV to rain or moisture.

For your own safety, do not touch any

part of the TV, power lead or aerial lead

during lightning storms.

Do not cover the ventilation openings of

the TV For ventilation, leave a space of

at least 10cm all around the set.

Do not cover the ventilation

openings of the TV with items such

as curtains or newspapers etc.

Never push objects of any kind into the

set as this could result in a fire or electric

shock. Never spill liquid of any kind on

the set. If any liquid or solid object does

fall into the cabinet, do not operate the

TV. Have it checked immediately by

qualified personnel.

Take care not to place heavy objects on

the power lead as this could result in

damage.

We recommend you wind any excess

lead around the holders provided on

the rear of the TV.

Unplug the power lead before moving

the TV. Avoid uneven surfaces, quick

steps or excessive force. If the set has

been dropped or damaged, have it

checked immediately by qualified

service personnel.

Safety Information

Clean the screen and cabinet with a soft,

lightly dampened cloth. Do not use any

type of abrasive pad, alkaline cleaner,

scouring powder or solvent, such as alcohol

or benzine, or antistatic spray. As a safety

precaution, unplug the TV before cleaning

it.

5

GB

Additional Safety Information

• Do not block or cover the ventilation opening situated on the bottom rear of the left hand side of the TV set.

For ventilation, leave a space of at least 10 cm from the wall.

• If after transporting the TV set, directly from a cold to a warm location, or if the room temperature has

changed suddenly, pictures may be blurred or show poor colour over portions of the picture. This is because

condensation has formed on the mirrors or lenses inside the TV set. Let the moisture evaporate before using

the TV set.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use

spot lighting directed down from the ceiling.

• This TV set incorporates the latest high-precision LCD technology. Even though the highest standards are

applied in manufacture it is still possible that a few black dots or bright points (red, green or blue) may be

visible on the screen under certain picture conditions. It is not possible to remove them and this is not a fault

condition.

• The screen of this TV set has an anti-reflection screen coating. To avoid screen degradation, follow the

advice given below:

• To remove dust from the surface of the screen, wipe with the supplied cleaning cloth or a soft cloth.

• Clean the screen and cabinet with a soft, lightly dampened cloth. Do not use any type of abrasive pad,

alkaline cleaner, scouring powder or solvent, such as alcohol or benzine, or antistatic spray. As a safety

precaution, unplug the TV before cleaning it.

• Avoid touching the screen, and take care not to scratch the surface with hard objects.

Safety Information

6

Checking the Accessories supplied

Inserting Batteries into the Remote Control

Make sure you insert the supplied batteries using the correct polarities.

Always remember to dispose of used batteries in an environmental friendly way.

1 Remote control (RM-906)

2 Batteries (AAA size)

Overview & Installation

2 Brackets

1 Hexagon key

2 Screws

1 Cleaning cloth

1 PC input cable

7

GB

Overview of Remote Control Buttons

1 TV I/ : To Temporarily Switch Off TV (standby mode):

Press this button to temporarily switch off TV (the standby indicator on the TV

lights up). Press again to switch on TV from standby mode.

• To save energy we recommend switching off completely when TV is not in

use.

• After 15 minutes without TV signal and without any button being pressed,

the TV switches automatically into standby mode.

2 VCR or DVD on/off: press this button to switch your VCR or DVD on or off.

3 Selecting input source: press this button repeatedly until the desired input symbol

of the source appears on the TV screen. Refer to page 25.

4 Selecting broadcast channels: if Media Selector (w; is switched to TV, press

these buttons to select channels. For double-digit programme numbers, enter the

second digit within 2.5 seconds.

5 Selecting VCR double-digit: if Media Selector (w;) is switched to VCR, press this

button to select double-digit channels for Sony's VCR e.g. 23, press -/-- first and next

the buttons 2 and 3.

6 a) Recording button:

If Media Selector (w;) is switched to VCR, press this button to record programmes.

b) Resetting to factory set levels:

Press, for a minimum of 3 seconds, to return the picture and sound settings to the

factory default levels. This will also return the set to the install condition and the

“Auto Tuning” menu will appear on the screen. If this is the case refer to the

section “Switching on the TV set and automatically Tuning” (page 11, step 5) of

this manual.

7 Watching last channel selected: if Media Selector (w;) is switched to TV, press

this button to return to the previous channel you were watching (provided you

watched it for at least 5 seconds).

8 Freezing a teletext page: in teletext mode, press this button to freeze a teletext

page. Press it again to cancel the freeze.

9 a) Displaying a channel index: if Media Selector

(w;) is switched to TV and MENU is switched off,

press OK to display a channel overview. If you

want to select a channel, press

v or V next press

again the OK button to watch the selected channel.

b) Navigator: if Media Selector (w;

) is switched to

TV and MENU (

qs) is switched on, use these

buttons to navigate through the menu system of the

TV. Refer to page 12.

q; Selecting the screen format: press this button

repeatedly to change the format of the screen. Refer

to page 16.

qa Selecting broadcast channels:

press these

buttons to select the next or previous broadcast

channel.

qs Menu system: press this button to enter the TV

menu system. Refer to page 12.

qd Adjusting volume: press these buttons to increase

or decrease the audio volume.

qf Selecting picture mode: press this button

repeatedly to change the picture mode. For details on

the different picture modes. Refer to page 13.

qg Selecting the sound effect:

Press this button

repeatedly to change the sound effect. For details on

different sound effects. Refer to page 14.

qh Fastext: In Teletext mode, these buttons can be

used as Fastext buttons. For details see page 22.

qj NexTView: press this button to display NexTView.

For details. Refer to page 23.

qk

Teletext: press this button to switch on Teletext. For

details see page 22.

ql Operating VCR or DVD: if Media Selector (w;) is

switched to VCR or DVD, these buttons will operate

the main functions of your VCR or DVD, once the

remote control has been programmed. Refer to page

26.

w; Media Selector: press this button to select which

device you want to operate, TV, VCR or DVD. A

green light will be momentarily lit to show which one

you have selected. For details refer to page 26.

wa Displaying Info: press this button to display all on-

screen indication such as channel number, etc. Press

again to cancel.

ws Selecting TV mode: press this button to switch off

PAP, Teletext or Video input mode.

wd

PAP (Picture And Picture): press this button to

divide the screen into two for watching two channels

simultaneously. Refer to page 21.

wf Muting the sound: press this button to mute the

TV sound. Press again to restore the sound.

Overview & Installation

1

qd

qs

q;

2

3

4

5

6

7

8

9

qf

qg

wa

w;

qk

ql

qj

qa

qh

ws

wd

wf

8

Overview of the TV Buttons

Overview & Installation

Audio Input

jacks

Selecting

Input source

Video Input jack

Volume control

buttons

Programme

Up or Down

Buttons

(Selects TV

channels)

S video

Input jack

Lamp indicator (see page 28).

On/Off

button

Headphones jack

Push up the flap

on the front left

corner of the

TV.

Remote control receiver

To operate the remote control,

pont it towards this receiver.

• Standby indicator (red colour).

• Power off indicator (amber colour).

Power on indicator (green colour).

9

GB

Connecting the Aerial and VCR

• Connecting cables are not supplied.

• For more details of VCR connections as well as other connections, please refer to page 24.

The Scart lead is optional. If you use this optional connection it can improve picture and sound quality when

using a VCR.

If you do not use a Scart lead, you will need to manually tune the VCR to a spare channel once the autotune

procedure has been completed. Refer to “Manual Programme Preset” on page 20. Also refer to your VCR

instruction manual to find out how to find the output channel of your VCR.

Stabilizing the TV set

Overview & Installation

After setting up, secure the TV set to a wall, etc., using the supplied brackets and screws, for safety purposes.

1 Mount the two supplied brackets with the screws provided to the upper rear side of the TV set.

2 Pass a strong cord or a chain through each bracket, and then secure to a wall or a pillar, etc.

Do not block or cover this ventilation opening. For

ventilation, leave a space of at least 10 cm from the

wall.

or

OUT IN

VCR

10

Switching On the TV and Automatically Tuning

The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose

the language of the menu screen 2) Choose the country in which you are going to operate the TV, 3) check how

to connect optional equipment to your TV, 4) search and store all available channels (TV Broadcast) and 5)

change the order in which the channels (TV Broadcast) appear on the screen.

However, if you need to change any of these settings at a later date, you can do that by selecting the appropriate

option in the (Set Up menu).

1 Connect the TV plug to the mains socket (220-240V AC, 50Hz)

The first time that the TV set is connected, it is usually turned on.

If the TV is off, press the on/off button on the TV set to turn

on the TV.

The first time you switch on the TV, a Language menu displays

automatically on the TV screen.

2 Press the V, v, B or b buttons on the remote control to select

your language, then press the OK button to confirm your

selection. From now on all the menus will appear in your chosen

language.

3 The Country menu appears automatically. Press the v or V

button to select the country in which you are using the TV. Press

the OK button to confirm your selection.

• If the country in which you want to use the TV set

does not appear in the list, select “off” instead of a country.

• To avoid wrong teletext characters for cyrillic languages we

recommend selecting Russia country if your own country

does not appear in the list.

Language

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Português

Polski

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Português

Polski

Select language

Country

Select country

Off

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

Schweiz/Suisse/Svizzera

First Time Operation

continued...

Language

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Português

Polski

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Português

Polski

Select language

Language

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Português

Polski

English

Nederlands

Français

Italiano

Deutsch

Türk çe

Español

Português

Polski

Select language

11

GB

4 A diagram will appear showing you how to connect a wide range

of equipment to your TV set. Follow the instructions and finally

press the OK button to remove the picture and continue the

automatic process.

After the automatic tuning process has finished and the

optional equipment has been connected at this stage, we

recommend you follow the instructions explained on the

section "Connection Guide" on page 17 to get the optimum

settings related with the optional equipment.

5 The Auto Tuning menu appears on the screen. Press the OK

button to select Yes.

6 The TV starts to automatically search and store all

available broadcast channels for you.

This procedure could take some minutes. Please be patient

and do not press any buttons, otherwise automatic tuning

will not be completed.

In some countries the TV Broadcaster installs the channels

automatically (ACI system). In this case, the TV

Broadcaster sends a menu in which you can select your city

by pressing the

v or V button and OK to store the

channels.

If no channels were found during the auto tune process, a

message appears automatically on the screen asking you to

connect the aerial. Check the aerial connection (refer to

page 9). Press the OK button to restart the auto tuning

process.

7 After all available channels are captured and stored,

the Programme Sorting menu automatically appears

on the screen enabling you to change the order in

which the channels are stored.

a) If you wish to keep the broadcast channels in the tuned order,

go to step 8.

b) If you wish to store the channels in a different order:

1 Press the v or V button to select the programme

number with the channel (TV Broadcast) you wish

to move. Press the b button.

2 Press the v or V button to select the new

programme number position for your selected

channel (TV Broadcast). Press the OK button to store.

3 Repeat steps b)1 and b)2 if you wish to change

the order of the other channels.

8 Press the MENU button to remove the menu from the screen

Auto Tuning

Programmes found: 4

No channel found.

Please connect aerial

Confirm

Programme Sorting

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

C58

S02

S06

Programme Sorting

01 TVE

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

C58

S02

S06

Do you want to start

automatic tuning?

Yes No

OK

Please connect your equipment

according to this chart

DVD

Your LCD TV is now ready for use

First Time Operation

12

Introducing and Using the Menu System

Your LCD TV uses an On-Screen menu system to guide you through the operations. Use the following buttons

on the Remote Control to operate the menu system:

1 To switch on the menu screens:

Press the MENU button to switch the first level menu on.

TV Functions

2 To navigate through the menus:

• To highlight and select the desired menu or option, press

v or V.

• To enter the selected menu or option, press OK or

b.

• To return to the last menu or option, press OK or

B.

• To alter the settings of your selected option, press v/V/B or b.

• To confirm and store your selection, press OK.

3 To switch off the menu screens:

Press the MENU button to remove the menu from the screen.

13

GB

The Picture Adjustment Menu

The “Picture Adjustment” menu allows you to

alter the picture settings.

To do this:

Press the MENU button and then press OK to

enter this menu. Next press

v or V to select the

desired option and press OK. Finally read below

how to operate into each option.

Picture Mode This option allows you to customise the Picture Mode based on the programme

you are watching. After selecting this option press OK. Next press repeatedly

v

or

V to select:

Personal (for individual settings).

Live (for live broadcast programmes, DVD and Digital Set Top Box receivers).

Movie (for films).

Once you have selected your desired option, press OK to store.

"Brightness", "Colour" and "Sharpness" level of "Live" and "Movie" mode are fixed on the

factory to get the best picture quality.

Contrast Press

B or b to reduce or enhance picture contrast. Next press OK to store.

Brightness Press

B or b to darken or brighten the picture. Next press OK to store.

Colour Press

B or b to decrease or to increase color intensity. Next press OK to store.

Hue Press

B or b to decrease or to increase the green tones. Next press OK to store.

Sharpness Press

B or b to soften or to sharpen the picture. Next press OK to store.

Reset Press OK to reset the picture to the factory preset levels.

Noise This option is set to On to automatically reduce the snowy picture

Reduction visible in the broadcast signal. To cancel this function, press

v or V to select Off.

Colour Tone This option allows you to alter the tint of the picture. After selecting this option

press b. Next press repeatedly v or V to select: Warm (gives the white colours

a red tint), Normal (gives the white colours a neutral tint), Cold (gives the white

colours a blue tint). Next press OK to store.

Lines While viewing an RGB input signal from the PC connector, some picture

Correction lines may be not correctly displayed. To correct this problem, select this option

and press

b. Next press repeatedly v or V to correct it berween -20 and +20.

Finally press OK to store.

• "Brightness" "Colour" and "Sharpness" only appears and only can be altered if "Picture

mode" is set to "Personal".

• "Hue" only appears and only can be altered for NTSC signal (e.g. USA video tapes).

• For an RGB input signal connected to the PC connector, only appear and only can be

altered: "Contrast", "Brightness" and "Lines Correction".

.

TV Functions

,

14

The Sound Adjustment Menu

The “Sound Adjustment” menu allows you to

alter the sound settings.

To do this:

Press the MENU button and press

v to select

, then press OK to enter this menu. Next

press

v or V to select the desired option and

press OK. Finally read below how to operate

into each option.

Sound This option allows you to customise the Sound Effect. After selecting this

Effect option press OK. Next press repeatedly

v or V to select:

Off (Flat response).

Natural (Enhances clarity, detail and presence of sound by using “BBE High

Definition Sound system”*).

Dynamic (“BBE High Definition Sound system”* intensifies clarity and

presence of sound for better intelligibility and musical realism).

Dolby** (Dolby Virtual, simulates the sound effect of “Dolby Surround Pro

Virtual Logic”).

Once you have selected your desired option, press OK to store.

Treble Press

B or b to decrease higher-frequency sounds. Next press OK to store.

Bass Press

B or b to decrease or to increase the lower-frequency sounds. Next press

OK to store.

Balance Press

B or b to emphasise the left or the right speaker. Next press OK to store.

Reset Press OK to reset the sound to the factory preset levels. Next press OK to store.

Dual Sound • For a Stereo broadcast:

Press

v or V to select Stereo or Mono. Next press OK to store.

• For a bilingual broadcast:

Press

v or V to select Mono (for mono channel if available), A (for channel 1)

or B (for channel 2). Next press OK to store.

TV Functions

,

m

Sound Adjustment

Sound Effect: Dolby Virtual

Treble:

Bass:

Balance:

Reset

Dual Sound: Stereo

Auto Volume: Off

TV Speakers: On

Headphones Set Up

Select: Enter:

OK

Exit:

MENU

Sound Adjustment

Sound Effect: Dolby Virtual

Treble:

Bass:

Balance:

Reset

Dual Sound: Stereo

Auto Volume: Off

TV Speakers: On

Headphones Set Up

Select:Back:

Enter:

OK

continued...

15

GB

Auto Volume Press v or V to select On (the volume level of the channels will stay the same,

independent of the broadcast signal, e.g. in the case of advertisements) or Off (the

volume level changes according to the broadcast signal). Next press OK to store.

If you select “Dolby Virtual” on the “Sound Effect” option, the “Auto Volume” option will

automatically be switched to “Off” and vice versa.

TV Speakers This option allows you to select if you want to listen the TV from the TV speakers

or from an external amplifier connected to the audio outputs on the rear of the TV.

After selecting this option, press OK. Next press repeatedly

v

or

V

to select:

On (to listen the TV from the TV set speakers).

One time off (to listen to the TV from the external amplifier only one

time. By using this option, any time the TV is turned

off/on, it returns to the default setting "On").

Permanent off (to always listen to the TV from external amplifier).

Once you have selected your desired option, press OK to store.

If you have selected "One time off" or "Permanent off", the volume of the external equipment

can also be altered by pressing the 2 +/- buttons of the remote control. When the volume

buttons are pressed, the symbol

% will appear indicating that the volume you are altering is

not the volume of the TV set speakers, it is from the external equipment.

Headphones Set Up This option allows you to customise the headphones volume and the

PAP settings (refer to page 21 for details on PAP).

After selecting this option press OK. Next press repeatedly

v or V to select:

volume Press

B or b to decrease or increase the volume level

from the headphones.

Dual Sound • For a Stereo broadcast:

Press

v or V to select Stereo or Mono

• For a bilingual broadcast:

Press

v or V to select Mono (for mono channel if

available), A (for channel 1) or B (for channel 2).

PAP Sound Select Frame if you want to listen to

the active screen (framed) of the PAP screen (see page

21), select Left picture if you want to listen to the left

screen or select Right picture if you want to listen to

the right screen.

* The “BBE High Definition Sound system” is manufactured by Sony Corporation under

license from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No.

4,482,866. The word “BBE” and BBE Symbol are trademarks of BBE Sound, Inc.

**This TV has been designed to create surround sound effect by simulating the sound of four

speakers with two speakers, when the broadcast audio signal is Dolby Surround encoded.

The sound effect can also be improved by connecting a suitable external amplifier (for

details refer to page 25).

**Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol

are trademarks of Dolby Laboratories.

TV Functions

16

The Features Menu

The “Features” menu allows you to alter vari-

ous settings of the TV.

To do this:

Press the MENU button and press

v twice to

select , then press OK to enter this menu.

Next press

v or V to select the desired option

and press OK. Finally read below how to

operate into each option.

AUTO FORMAT

This option allows you to automatically change the aspect ratio of the screen.

To do this:

After selecting the option, press OK. Then press

v or V to select On (if you wish the TV set to

automatically switch the screen format according to the broadcast signal) or Off (if you wish to

keep your preference). Finally press OK to store.

Even if you have selected “On” or “Off”, you can always modify the format of the screen by

pressing repeatedly on the remote control to select one of the following formats:

SMART: Imitation of wide screen effect for 4:3 broadcast.

4/3: Conventional 4:3 picture size, full picture

information.

14/9: Compromise between 4:3 and 16:9 picture size.

ZOOM: Widescreen format for letterbox movies.

WIDE: For 16:9 broadcast. Full picture information.

• In “SMART”, “ZOOM” and “14/9” modes, parts of the top and bottom of the screen are

cut off. Press

v or V to adjust the position of the image on the screen (e.g. to read subtitles).

• Only "WIDE" and "4/3" modes can be selected for an RGB signal connected to the PC

connector.

• According to the format of diffussion, black bands can always appear whatever the selected

mode.

TV Functions

,

m

4:3

ZOOM

14:9

WIDE

SMART



continued...

17

GB

AV3 OUTPUT

This option allows you to select the source to be output from the Scart connector

3/ 3 so that you can record from this Scart any signal coming from the TV or from an

external equipment connected to the Scart connector 1/ 1, 2/ 2 or front connectors

4 or 4 and 4.

If your VCR supports SmartLink, this procedure is not necessary.

To do this:

Once you have entered into the "Features" menu as it is explained in the previous page and after

selecting the option, press OK. Then press

v

or

V

to select the desired output signal:

TV to output the aerial source.

AV1 to output sources connected to 1/ 1.

AV2 to output sources connected to 2/ 2.

AV4 to output sources connected to 4 or 4 and 4.

AUTO to output the signal that is being viewed on the TV.

• If you select “AUTO”, the output signal will always be the same one that is displayed on

the screen.

• If you have connected a decoder to the Scart 3/ 3 or to a VCR connected to this

Scart, please remember to change back the “AV3 Output” to “TV” for correct

unscrambling.

CONNECTION GUIDE

Even you have already connected the external equipment to the TV set, it is important for you to

follow the instructions of this menu. If you proceed in this way, you will get the optimum picture

settings related with the optional equipment.

To do this:

1 Once you have entered the "Features" menu as it is explained in the previous page and after

selecting the option, press OK. Next press

v or V to chose the equipment you want to connect

among the available: SAT (satellit), Decoder, DVD, GAME, VIDEO or DVD rec. (DVD

recorder). Next press

b to select the equipment chosen (equipment selected also can be deleted

by pressing

B). Once you have selected all the equipment to be connected, press v or V to

select "Confirm" and press OK.

2 A new menu will appear showing you on which Scart connector of the rear of the TV should be

connected each equipment. Please connect each equipment according to this information to get

the optimum picture setting of the optional equipment.

3 Once you have connected the optional equipment, press B or b to select "OK" and finally press

the OK button of the remote control.

We strongly recommend you to follow our connection proposals, but in case you do not agree press B

or b to select «No» and next press the OK button. A new menu appears on the screen in which you

can assign the connections according to your preferences.

RGB CENTRING

This option is only available if an RGB source has been connected to the TV.

This option allows you to readjust the horizontal position of the picture in case you need to do it

when connecting an RGB source.

To do this:

Once you have entered the "Features" menu as it is explained in the previous page and while

watching an RGB source select the “RGB Centring” option and press OK. Then press

v or V to

adjust the centre of the picture between –5 and +5. Finally press OK to confirm and store.

S

TV Functions

18

The Set Up Menu

The “Set Up” menu allows you to alter various

options on this TV.

To do this:

Press the MENU button and press

v

three

times to select , then press OK to enter this

menu. Next press

v

or

V

to select the desired

option and press OK. Finally read below how

to operate into each option.

LANGUAGE

This option allows you to select the language that menus are displayed in.

To do this:

After selecting the option, press OK and then proceed in the same way as in step 2 of the section

"Switching On the TV and Automatically Tuning" on page 10.

COUNTRY

This option allows you to select the country in which you wish to operate the TV set.

To do this:

After selecting the option, press OK and then proceed in the same way as in step 3 of the section

"Switching On the TV and Automatically Tuning" on page 10.

AUTO TUNING

This option allows you to automatically search for and store all available TV channels.

To do this:

After selecting the option, press OK and then proceed in the same way as in the steps 5 and 6 of

the section “Switching On the TV and Automatically Tuning” on page 11.

PROGRAMME SORTING

This option allows you to change the order in which the channels (TV Broadcast) appear on the

screen.

To do this:

After selecting the option, press OK and then proceed in the same way as in the step 7 of the section

“Switching On the TV and Automatically Tuning” on page 11.

TV Functions

,

m

Select: Exit:

MENU

Set Up

Language

Country

Auto Tuning

Programme Sorting

Programme Labels

AV Preset

Manual Programme Preset

Enter:

OK

Set Up

Language

Country

Auto Tuning

Programme Sorting

Programme Labels

AV Preset

Manual Programme Preset

Select:Back:

Enter:

OK

continued...

19

GB

PROGRAMME LABELS

This option allows you to name a channel using up to five characters (letters or numbers).

To do this:

1 Once you have entered the "Set Up" menu as it is explained in the previous page and after selecting the option,

press OK, then press v or V to select the programme number with the channel you wish to name. Next press OK.

2 With the first element of the Label column highlighted, press OK and

v

,

V

, B or b to select the letter, next

press OK.

When you have finished, press

v

,

V

, B or b to select the word “End” on the screen and finally press OK to

turn off the menu from the screen.

• To correct the letter, select "

%" on the screen to go back and press OK.

• For a blank, select " " on the screen and press OK.

AV PRESET

This option allows you to:

a) Designate a name to the external equipment you have connected to the input sockets of the TV set.

To do this:

1 Once you have entered the "Set Up" menu as it is explained in the previous page and after selecting the option,

press OK, then press

v

or

V

to select the input source you wish to name: AV1, AV2 or AV3 for the rear

Scarts, AV4 for front connectors and AV5 for the PC input connector. Next press OK twice.

2 A label automatically appears in the label column:

a) If you want to use one of the predefined labels, press

v or V to select the desired label and finally press OK.

The total predefined labels are: VIDEO, DVD, CABLE, GAME, CAM (camcorder), SAT (satellite)

or PC (only for the AV5).

b) If you want to set a different label, select Edit and press OK. Then, with the first element highlighted, press

v, V, B or b to select the letter, next press OK. When you have finished, press v, V, B or b to select

the word “End” on the screen and finally press OK to turn off the menu from the screen.

• To correct the letter, select "

%" on the screen to go back and press OK.

• For a blank, select " " on the screen and press OK.

b) Change the input sound level of the optional equipment connected.

To do this:

Once you have entered the "Set Up" menu as it is explained in the previous page and after selecting the option

press OK, then press

v

or

V

to select the input source you want to alter the input sound level: AV1, AV2 or

AV3 for the rear Scarts, AV4 for front connectors and AV5 for the PC input connector. Next press twice

b to

highlight the Sound Offset column. Finally press OK and

v

or

V

to alter the input sound level between -9 and

+9.

TV Functions

continued...

20

MANUAL PROGRAMME PRESET

This option allows you to:

a) Preset channels or the VCR channel one by one to the programme order of your choice.

To do this:

1 Once you have entered the “Set Up”menu as it is explained on page 18 and after selecting the "Manual

Programme Preset" option, press OK. Next with Programme option highlighted press OK.

Press

v or V to select which programme number you want to preset the channel on (for VCR, select

programme number “0”). Then press B.

2 The following option is only available depending on the country you have selected in the “Country”

menu.

After selecting the System option, press OK. Then press

v

or

V

to select the TV Broadcast system (B/G

for western European countries, D/K for eastern European countries, L for France or I for United Kingdom).

Then press

B.

3 After selecting the Channel Number option, press OK. Next press

v

or

V

to select the channel tuning ("C"

for terrestrial channels or "S" for cable channels). Then press the number buttons to enter directly the channel

number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press

b and v or V to search for it. When you have tuned the desired channel, press OK twice to store.

Repeat all the above steps to tune and store more channels.

b) Label a channel using up to five characters.

To do this:

Once you have entered the “Set Up”menu as it is explained on page 18 and after selecting the "Manual

Programme Preset" option, press OK. Next with the Programme option, highlighted press the PROG +/- button

to select the programme number with the channel you wish to name. When the programme you want to name

appears on the screen, select the Label option and press OK. Then, with the first element highlighted, press

v

,

V

, B or b to select the letter, next press OK. When you have finished, press

v

,

V

, B or b to select the word

“End” on the screen and finally press OK to turn off the menu from the screen.

• To correct the letter, select "

%" on the screen to go back and press OK.

• For a blank, select " " on the screen and press OK.

c) Fine tune the broadcast reception. Normally the automatic fine tuning (AFT) will give the best possible picture,

however you can manually fine tune the TV to obtain a better picture reception in case the picture is distorted.

To do this:

While watching the channel (TV Broadcast) you wish to fine tune, and once you have entered the “Set Up” menu

as it is explained on page 18 and after selecting the "Manual Programme" option, press

OK

.

Then select the AFT

option and press

b. Next press

v

or

V

to adjust the fine tuning between -15 and +15. Finally press OK twice

to store.

d) Skip any unwanted programme numbers when they are selected with the PROG +/- buttons.

To do this:

Once you have entered the "Set Up" menu as it is explained on page 18 and after selecting the "Manual

Programme Preset" option, press OK. Next with the Programme option highlighted, press the PROG +/- button

to select the programme number you want to skip. When the programme you want to skip appears on the screen,

select the Skip option and press

b

. Next press

v

or

V

to select On. Finally press OK twice to confirm and store.

To cancel this function afterwards, select “Off” instead of “On” in the step above.

e) View and record scrambled channels (e.g. from a pay TV decoder) when using a decoder connected to Scart

3/ 3 directly or through a VCR.

This option is only available depending on the country you have selected in the “Country” menu.

To do this:

Once you have entered the "Set Up" menu as it is explained on page 18 and after selecting the "Manual Programme

Preset" option, press OK. Next select the Decoder option and press

b. Next press v or V to select On. Finally

press OK twice to confirm and store.

To cancel this function afterwards, select "Off" instead of "On" in the step above.

S

TV Functions

21

GB

Switching PAP on and off

1 Press to display PAP.

One of the screens will be framed to indicate that this is

the active screen. It means that when you want to select

the PAP source, you will be doing it in the active screen.

2 Press again to remove PAP.

On the screen appears a banner guiding you how to operate

PAP. This banner will disappear after some seconds but it

always can be displayed again by pressing the button.

Changing the active screen

This is only possible if Media Selector is set to TV.

To change the active screen (framed), press the B or b buttons.

Selecting PAP source

1 Selecting a TV channel:

Press the

B button to select the left screen as the active screen. Next press the number buttons

or PROG +/- to select a TV channel.

Video input signals can not be displayed on the left screen.

2 Selecting an input source:

Press the

b button to select the right screen as the active screen. Next press repeatedly the

button to watch the input signal of a connected equipment onto the TV right screen. For more

details on which input symbol you want to choose, please see section "Viewing pictures from

equipment connected to the TV" on page 25.

RF signal (TV broadcast channels) can not be displayed on the right screen.

Selecting the sound

The sound of the active screen (framed) always comes from the TV set loudspeakers.

Besides that, you can listen to the active screen as well as the non active screen via headphones.

To do this:

With the PAP switched on, refer to the section "The Sound Adjustment Menu", select "Headphones

Set Up" and set the option " PAP Sound" according your preference. For details see page 15.

In PAP (picture and picture) mode, the output from the Scart 2/ 2 is fixed to the right

picture.

TV Functions

PAP (PICTURE AND PICTURE)

PAP divides the screen into two to watch two pictures in format 4:3 simultaneously.

Strona jest ładowana ...

Sony KF-50SX300K Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Sony KF-50SX300K Instrukcja obsługi

w innych językach

Powiązane dokumenty