Yamaha mLAN8E Instrukcja obsługi

Marka: Yamaha

Model: mLAN8E

Kategoria: Sprzęt muzyczny

Typ: Instrukcja obsługi

Owner’s manual

Bedienungsanleitung

Mode d’emploi

mLAN EXPANSION BOARD

mLAN8E

EnglishDeutschFrançais

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the an-

tenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

CANADA

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

• This applies only to products distributed by Yamaha Canada Music Ltd.

• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.

(class B)

Table of Contents

Introduction ................................................................................... 4

Installing the mLAN8E ................................................................... 4

Package Contents........................................................................... 4

Features .......................................................................................... 5

Names and Functions..................................................................... 6

Connections.................................................................................... 7

Internal Configuration of the mLAN8E.......................................... 8

Settings on the device in which the mLAN8E is installed ........... 10

For the A5000/A4000.........................................................................10

For the CS6x/CS6R/S80 .....................................................................15

LED Messages ............................................................................... 21

Specifications................................................................................ 22

English

Introduction

Thank you for purchasing the Yamaha mLAN8E. The mLAN8E is an expansion board that

provides an mLAN interface. mLAN is a digital network designed for music and based on the IEEE

1394 high performance serial bus. mLAN makes it easy to construct sophisticated networks for

audio and MIDI signals without having to re-conﬁgure the cabling as was necessary with

previous systems.

The mLAN8E includes mixer functionality, and is a powerful enhancement to your music

production system.

In order to take full advantage of the mLAN8E’s functionality, please read this manual carefully.

After reading this manual, keep it for future reference.

Installing the mLAN8E

Installation of the mLAN8E must be performed by one of the qualiﬁed Yamaha service person-

nel or Yamaha dealers listed at the end of the manual of the device in which the mLAN8E is to

be installed.

Package Contents

• mLAN8E unit

• mLAN Tools (CD-ROM)

• IEEE1394 cable (4.5m)

• 26-pin ﬂat cable (for connecting mLAN8E and mLAN8E-compatible devices)

• Tape (for fastening cables)

• Owner’s manual (this document)

• mLAN Guide Book

• mLAN Tools Installation Guide

About the included CD-ROM

The included CD-ROM contains software that is useful when used in conjunction with the

mLAN8E. The software includes “mLAN Patchbay” which allows audio /MIDI signal routing

between electronic musical instruments connected to the mLAN8E to be controlled from your

computer, and “mLAN Mixer” which allows the mixer/dynamics processor functionality of the

mLAN8E to be controlled from your computer. For details refer to the separate “mLAN Tools

Installation Guide.”

Yamaha cannot be held responsible for damage caused by improper use or

modiﬁcations to the instrument, or data that is lost or destroyed.

The illustrations and LCD screens shown in this Owner’s Manual are for instructional purposes only, and

may appear somewhat different from those on your device.

The company names and product names in this Owner’s Manual are the trademarks or registered

trademarks of their respective companies.

English

Features

■

Fast data transfer via mLAN

mLAN is a digital network designed for music. It uses the IEEE 1394 high performance serial bus,

and allows you to construct systems that are more sophisticated yet simpler than ever before. For

details on mLAN, refer to the separate “mLAN Guidebook.”

■

16 channel mixer functionality

A 16 channel digital audio mixer is built in.

■

Built-in equalizer / dynamics processor

A four-band equalizer and dynamics processor provide sophisticated audio control.

* Mixer / equalizer / dynamics processor settings are made using the included “mLAN

Mixer” application. For details refer to the mLAN Mixer manual (electronic manual).

English

Names and Functions

Rear Panel

SERIAL I/O jack

This jack is used to connect the mLAN8E directly to a personal computer via a serial cable. Use this

jack to connect the mLAN8E and the computer when you are using the mLAN Patchbay and mLAN

Mixer on Windows. This is not used to input or output MIDI and audio signals. Refer to page 7 for

more information on the connections.

mLAN (IEEE1394) jacks

These jacks are used to connect mLAN devices or IEEE1394-compatible devices via IEEE1394 stan-

dard (6-pin) cables. Each jack has an LED in the upper left corner to indicate the following statuses.

green : The mLAN8E or connected device is a “leaf” node.

off : Not connected.

red : If the cable is disconnected, the sound will be interrupted on a connected device or other

device.

RT/ERR LED

This LED indicates the following statuses.

green : The mLAN8E is a “root.”

orange : An error has occurred. (IEEE1394 bus-related)

red : An error has occurred. (Other errors)

off : Status other than above.

Refer to “LED Messages” on page 21 for information on the error indication.

ACTIVE LED

This LED indicates the following statuses.

blue : The relay function is active.

off : The relay function is disabled.

Since the mLAN8E does not function as a bus relay when the power is turned off, the active

LED also indicates whether the power to the unit is on (blue) or off.

3 12

NOTE

English

Connections

Here’s how to connect the mLAN8E to other mLAN devices or to your computer.

Connecting an mLAN (IEEE1394) device

Use an IEEE1394 standard (6-pin) cable to connect the mLAN (IEEE1394) jack on the mLAN

(IEEE1394) device to the mLAN (IEEE1394) jack on the mLAN8E. At this time, you do not have to

turn off the power to either device.

Connecting a Windows computer (serial connection)

Use a serial cable to connect the computer’s RS232C jack to the mLAN8E’s SERIAL I/O jack. At this

time, make sure that the power to the computer and the device in which the mLAN8E is installed

is turned off.

Make this serial connection when using the included software on Windows. To use on a Macin-

tosh, connect the mLAN8E’s mLAN jack and the Macintosh’s FireWire port using an IEEE1394

cable. (See “Connecting an mLAN device.”)

Use a standard D-SUB 9P

→

MINI DIN 8P cable.

mLAN8E

mLAN (IEEE1394) device

IEEE1394

standard cable

IEEE1394 standard cable

Macintosh computer

that supports FireWire

CONTRAST ANALOG MIDI

OUT-B OUT-A IN

SERIAL I/O

RT/ERR

ACTIVE

mLAN IEEE1394 S200

123

OPTICALCOAXIAL

OUT IN OUT IN

DC IN

OUT2/R OUT1/L IN2/R IN1/L

NOTE

mLAN8E

computer

RS-232C

(DB9)

English

Internal Conﬁguration of the

mLAN8E

mLAN device

mLAN jacks1-3

mLAN8E-

compatible

device

mLAN

audio input*

Digital Mixer section*

mLAN

MIDI IN

Source

select

Tone

generator

section

mLAN

audio output

mLAN

MIDI OUT

MIDI device

audio device

e.g., mixer,

powered speakers

mLAN MIDI/

MIDI

conversion

MIDI/

mLAN MIDI

conversion

MIDI INMIDI OUT ANALOG IN ANALOG OUT

mLAN8E

non-mLAN signals

mLAN signals

mLAN cables

non-mLAN cables

Input

Output

MIDI transmit/

receive section

English

mLAN output plugs (Indicated in the

“From” field in mLAN Patchbay.)

mLAN audio

Mix L (stereo mix L)

Mix R (Stereo mix R)

AUX1

AUX2

AUX3

AUX4

AUX5

AUX6

mLAN MIDI

MIDI OUT

mLAN plugs (in Mixer mode)

mLAN input plugs (Indicated in the

“To” field in mLAN Patchbay.)

mLAN audio

CH9

CH10

CH11

CH12

CH13

CH14

CH15

CH16

mLAN MIDI

MIDI IN

In Direct mode, the number and names of plugs displayed will differ according to the

device in which the mLAN8E is installed (page 22).

There are no mLAN input plugs corresponding to the A/D INPUT of the CS6x/CS6R/S80.

NOTE

Internal Conﬁguration of the mLAN8E

The diagram on the left illustrates the entire signal ﬂow.

The mLAN8E has 16-channel digital mixer functionality, and can mix mLAN audio signals with audio

signals produced by the device that contains the mLAN8E.

The input/output destinations of these signals and the mixer functionality can be easily controlled

from your computer by using the included mLAN Tools.

The mLAN8E mixer section features Direct mode and Mixer mode. When the mLAN Mixer is

not being used, the unit is in Direct mode, in which signals are input and output directly. When

mLAN Mixer is being used, the unit enters Mixer mode. The default setting (when you turn on

the power to the unit) is Direct mode. If you turn the power to the device off, then on while

mLAN Mixer is running, restart mLAN Mixer.

*1 The included mLAN Mixer application is required in order to make digital mixer settings. For details on

the structure of the digital mixer section, refer to the block diagram of the mLAN Mixer manual.

*2 For mLAN audio inputs, you can select from any 8 channels on the bus (system).

NOTE

English

Settings on the device in which

the mLAN8E is installed

If the mLAN8E is installed in the A5000/A4000, you will be able to make mLAN-related settings.

mLAN settings are made in Utility mode.

In order to use mLAN, you must ﬁrst access the mLAN Conﬁguration page

and set MIDI Input to a setting other than MIDI IN.

mLAN Cnct (mLAN connections)

mLAN connections tone generators are saved in the mLAN8E. They cannot

be saved on disk.

Cursor

Out (output)

■

Knob 1

[ turn] Move cursor / switch pages

Move the cursor or switch pages.

[ press] Tree View

Access the Tree View screen.

■

Knob 2

[ turn] Out (select output plug)

Select the mLAN plug of the mLAN8E that will be the output source.

❑

Setting:

AS (assignable) 1~6, DIG-L, DIG-R, MIDI

For the A5000/A4000

NOTE

English

Settings on the device in which the mLAN8E is installed

■

Knob 3

[ turn] Connect# (select connection number of the connected mLAN device)

Select the connection number of the connected mLAN device. In the case of numbers for

which a connection has already been made, the module name and plug name will be dis-

played in parentheses. If there are fewer than 62 connections, you can select “New” and cre-

ate a new connection (mLAN input plug).

❑

Setting:

1~62, New

[ press] mLAN_INIT (mLAN initialize)

Initialize mLAN-related settings. This will be executed after you reply to a conﬁrmation dialog

box.

All connection settings will be set to “---”. The Word Clock Mode will be “Auto.”

The Nickname settings will not be initialized.

■

Knob 4

[ turn] Module (select connected module)

Select an mLAN device on the mLAN bus (system). When you select a valid mLAN device, the

top line will show the vendor name and the Nickname.

Settings cannot be modiﬁed for the connection number of an already-estab-

lished connection.

■

Knob 5

[ turn] Plug (select connected mLAN plug)

Select the mLAN input plug of the connected mLAN device.

The connection is executed by CONNECT (press knob 5). If after making

your selection, you change pages, move the cursor, or change the Out or

Connect# settings without executing CONNECT, the selected value will be

cleared.

If there are no plugs that can be selected, this will be displayed as “---.”

[ press] CONNECT

Connect to the mLAN input plug of the selected mLAN device.

If the connection number is “New,” this function will appear if you have selected a module

name or plug name that can be connected.

[ press] CUT (disconnect)

Break the selected connection.

This function will appear if you have selected an already-connected module name / plug

name.

NOTE

English

Settings on the device in which the mLAN8E is installed

Cursor

In (input)

■

Knob 1

[ turn] Move cursor / switch pages

Move the cursor or switch pages.

[ press] Tree View

Access the Tree View screen.

■

Knob 2

[ turn] In (select input plug)

Select the mLAN8E mLAN plug that will input the signal. If a connection has already been

made, the module name and plug name will be displayed in parentheses.

❑

Setting:

AD-L, AD-R, MIDI

■

Knob 3

Display only

If unconnected, this will indicate “New.”

[ press] mLAN_INIT (mLAN initialize)

Initialize mLAN-related settings. This will be executed after you reply to a conﬁrmation dialog

box.

All connection settings will be set to “---”. The Word Clock Mode will be “Auto.”

The Nickname settings will not be initialized.

■

Knob 4

[ turn] Select connected module

Select an mLAN device on the mLAN bus (system). When you select a valid mLAN device, the

top line will show the vendor name and the Nickname.

■

Knob 5

[ turn] Select connected mLAN plug

Select an mLAN output plug on the connected mLAN device.

The connection is executed by CONNECT (press knob 5). If after making

your selection, you change pages, move the cursor, or change the Out or

Connect# settings without executing CONNECT, the selected value will be

cleared.

If there are no plugs that can be selected, this will be displayed as “---.”

[ press] CONNECT

Connect to the mLAN output plug of the selected mLAN device.

If the node number is “New,” this function will appear if you have selected a module name or

plug name that can be connected.

[ press] CUT (disconnect)

Break the selected connection.

This function will appear if you have selected an already-connected module name or plug

name.

NOTE

English

Settings on the device in which the mLAN8E is installed

mLAN Cnfg (mLAN configuration)

Output Level Offset, Word Clock Mode, and Nickname settings are saved in

the mLAN8E. They cannot be saved on disk.

Cursor

■

Knob 1

[ turn] Move cursor / switch pages

Move the cursor or switch pages.

[ press] Tree View

Access the Tree View screen.

■

Knob 2

[ turn] Output Level Offset

Specify the output volume (offset value) for all mLAN audio outputs.

❑

Setting:

+0 dB ~ +24 dB

■

Knob 4

[ turn] Audio Input (audio input select)

Select the audio input source.

❑

Setting

ADIn: Use two analog audio channels from the INPUT jacks of the A5000/A4000.

mLAN: Use two mLAN audio channels. The audio signals from the INPUT jacks of the A5000/

A4000 will not be input.

Cursor

■

Knob 1

[ turn] Move cursor / switch pages

Move the cursor or switch pages.

[ press] Tree View

Access the Tree View screen.

■

Knob 3

[ turn] Word Clock Mode

Specify the word clock.

❑

Setting

Auto: The word clock of the audio output will automatically synchronize to an 44.1 kHz external

device. The A5000/A4000 may function as the master in some cases, or as the slave in

other cases.

Group1Master (44.1 kHz): The A5000/A4000 will function as a 44.1 kHz master device.

NOTE

English

Settings on the device in which the mLAN8E is installed

Before the Word Clock Mode is selected or after SET is executed, this will indicate the current

Word Clock Mode. The display has the following signiﬁcance.

•

Auto(Int): Operating in Auto Mode on the internal clock

•

Auto(Ext): Operating in Auto Mode as a slave

•

---(Int): Operating in Manual Mode on the internal clock

•

---(Ext): Operating in Manual mode as a slave

[ press] SET (finalize word clock)

Finalize the selected Word Clock Mode setting.

■

Knob 4

Nickname (display only)

Displays the Nickname of the A5000/A4000.

[ press] Rename

Set the Nickname.

■

Knob 5

[ turn] MIDI Input (MIDI Input selection)

Regardless of this setting, the same MIDI output data is sent from both MIDI

OUT and mLAN MIDI.

Regardless of this setting, the MIDI THRU connector will re-transmit the data

that was input to MIDI IN.

❑

Setting

MIDI IN: MIDI messages input from the MIDI IN connectors will play the A5000/A4000; mLAN will

not be used.

mLAN->A: MIDI messages from the mLAN MIDI input will be sent to the MIDI IN-A port. MIDI mes-

sages from the rear panel MIDI IN-A connector will not be input (A5000 only).

mLAN->B: MIDI messages from the mLAN MIDI input will be sent to the MIDI IN-B port. MIDI mes-

sages from the rear panel MIDI IN-B connector will not be input (A5000 only).

mLAN: MIDI messages from the mLAN MIDI input will be input to the MIDI IN port. MIDI mes-

sages from the rear panel MIDI IN connector will not be input (A4000 only).

NOTE

English

Settings on the device in which the mLAN8E is installed

If the mLAN8E is installed in the CS6x/CS6R/S80, you will be able to make mLAN-related settings.

mLAN settings are made mainly in Utility mode.

MIDI settings

Press the [UTILITY] key to enter Utility mode.

Turn the [PAGE] knob to access the “MIDI Other” page.

Use knob [B] to set “In” to “mLAN.”

For the CS6x/CS6R/S80

SHIFT PAGE

PA RT

ELEMENT

DATAABC1 2

MIDI Other) In ThruPort Sync SeqCtrl

Sys MIDI 1 int on

SHIFT PAGE

PA RT

ELEMENT

DATAABC1 2

MIDI Other) In ThruPort Sync SeqCtrl

Sys mLAN 1 int on

English

Settings on the device in which the mLAN8E is installed

MIDI Other

An CS6x/CS6R/S80 in which the mLAN8E is installed will have the following additional functions.

■

In (MIDI Input)

Select whether to use the MIDI connector or the mLAN connector as the input route for MIDI

messages. If you select “mLAN,” the HOST SELECT switch will have no effect, and MIDI mes-

sages from devices connected to the TO HOST connector or MIDI IN connector will not be

input.

❑

Setting:

MIDI, mLAN

Regardless of this setting, MIDI OUT messages will be output both from the

MIDI OUT connector and the mLAN connector.

If you select mLAN, MIDI OUT messages will not be output from TO HOST.

If you select mLAN, the ThruPort setting will have no effect.

■

Sync (when the above MIDI Input = mLAN)

When playing in synchronization with an external device, specify whether the CS6x/CS6R/S80

will operate using its own internal clock or the MIDI Clock received via the mLAN connector. If

you select “Int (internal),” the CS6x/CS6R/S80 will operate using its own internal clock. Select

this when using the CS6x/CS6R/S80 by itself or as the master of a synchronized performance

using MIDI Clock. If you select “MIDI,” the CS6x/CS6R/S80 will operate according to the

MIDI Clock received via the mLAN connector. Select this when using the CS6x/CS6R/S80 as a

slave of a synchronized performance using MIDI Clock.

❑

Setting:

MIDI, int (internal)

■

SeqCtrl (Sequence Control) (when the above MIDI Input = mLAN)

Specify whether or not you wish to transmit and receive the mLAN MIDI messages Start, Stop,

and Continue. This is also a switch for outputting MIDI Clock from mLAN MIDI output.

❑

Setting:

off (don’t transmit or receive), on (transmit and receive)

MIDI Other) In ThruPort Sync SeqCtrl

Sys mLAN 1 int on

NOTE

English

Settings on the device in which the mLAN8E is installed

mLAN Connection, Word Clock, and Nickname settings

The method of entering each page is the same as for MIDI Setting. In Utility

mode, turn the [PAGE] knob to display the desired page. (Page 15)

mLAN Connect (mLAN connection)

mLAN plug of the mLAN8E

The number of plugs and their names will differ depending on the device in

which the mLAN8E is installed.

This indicates an input setting (

) or output setting (

). In the example

shown above, the MIDI OUT plug of the mLAN8E is being connected to an

external S80 (Nickname=Vivien).

Vendor name of connected device

Nickname of connected device

Connection number of connected device

Module name of connected device

mLAN plug name of connected device

Connect/disconnect

[ENTER] toCnct ... press the [ENTER] key to connect

[ENTER] toCut ... press the [ENTER] key to disconnect

NOTE

SHIFT PAGE

PART

ELEMENT

DATAABC1 2

mLAN Connect)YAMAHA :Vivien [ENTER]

MIDI OUT->New:S80 MIDI-IN toCnct

1 2 7

4 8

NOTE

English

Settings on the device in which the mLAN8E is installed

•

mLAN8E output settings

(1) Turn knob [A] to select the output source mLAN plug of the mLAN8E.

You can turn knob [B] to check up to 62 Connection numbers for destination

mLAN devices.

If no previously-speciﬁed connection destinations are found, the display will

indicate “*****”.

If the connection has not been established, “New” will be displayed above

knob [B], and “[ENTER] toCnct” will be displayed above knob [2].

If the connection has already been established, the current connection des-

tination will be displayed. Also, “[ENTER] To Cut” will be displayed above

knob [2]. In this case, pressing [ENTER] will cut the connection.

(2) Turn knob [C] to select an mLAN device on the mLAN bus (system). The upper line will show

the vendor name, and the lower line will show the module name.

(3) Turn knob [1] to select the mLAN input plug of the connected mLAN device, and press the

[ENTER] key. The connection will be executed, and the “New” indication will change to a

number.

To change an existing connection, you must ﬁrst break the connection and

then specify a new connection.

If the names (vendor name, module name, mLAN plug name) of the con-

nected device exceed eight characters, only the ﬁrst eight characters will be

displayed.

NOTE

English

Settings on the device in which the mLAN8E is installed

•

mLAN8E input settings

An mLAN input plug of the mLAN8E can have only one connection.

(1) Turn knob [A] to select the mLAN8E mLAN plug that will input the signal. The module name

and plug name for the destination device will be displayed as “-----”.

If a connection has already been established, the current connection desti-

nation will be displayed. Also, the display will indicate “[ENTER] To Cut”

above knob 2. In this case, press [ENTER] to break that connection.

(2) Turn knob [C] to select an mLAN device on the mLAN bus (system). The upper line will show

the vendor name, and the lower line will light the module name.

(3) Turn knob [1] to select an mLAN input plug on the destination mLAN device, and press

[ENTER] to execute the connection.

To change an existing connection, you must ﬁrst break the connection and

then specify a new connection.

If the names (vendor name, module name, mLAN plug name) of the con-

nected device exceed eight characters, only the ﬁrst eight characters will be

displayed.

mLAN connections tone generators are saved in the mLAN8E. They cannot

be saved on a memory card.

mLAN W

ord Clock

Select the Word Clock.

■

Mode

Select whether the CS6x/CS6R/S80 will function as the Word Clock Master (Group 1 Master)

of the connected mLAN Audio network, or whether the slave/master setting will be selected

automatically (auto). When you select the Mode and press [ENTER], a conﬁrmation screen will

appear. To execute the setting press [YES]. To cancel press [NO]. When the setting has been

ﬁnalized, the display will indicate “(int)” or “(ext=********)” at the right of Mode. “(int)” indi-

cates that the CS6x/CS6R/S80 in which the mLAN8E is installed is acting as the word clock

master. “(ext=********)” indicates that it is acting as the slave of an external module named

“********”.

❑

Setting:

auto (44.1 kHz), Group1Master (44.1 kHz)

This setting is stored in the mLAN8E. It cannot be saved on a memory card.

NOTE

mLAN WordClock) Mode [ENTER]

Sys Group1Master(44.1kHz) to Set

NOTE

English

Settings on the device in which the mLAN8E is installed

mLAN initialize

This initializes the mLAN connection and word clock settings of the mLAN8E installed in the

CS6x/CS6R/S80. When you press [ENTER], a conﬁrmation screen will appear. Press [YES] to exe-

cute the initialization, or press [NO] to cancel.

The Nickname settings will not be initialized.

mLAN Nickname

Specify the nickname of the CS6x/CS6R/S80 in which the mLAN8E is installed. The input proce-

dure is the same as when inputting a CS6x/CS6R/S80 voice name.

After inputting the name, press [ENTER] to finalize it.

Other mLAN-related settings

•

Voice mode

For OSC Pan (oscillator pan) Output, you will be able to specify ind3~ind6.

•

Performance mode

For LYR Out (layer out) Output, you will be able to specify ind3~ind6.

•

Phrase Clip mode (CS6x/CS6R)

For OSC Pan (oscillator pan) Output, you will be able to specify ind3--ind6.

mLAN Initialize) [ENTER]

Sys to Init

NOTE

mLAN Nickname) a-Z 0-? Cursor

Sys [Vivien ]

Strona jest ładowana ...

Yamaha mLAN8E Instrukcja obsługi

Marka: Yamaha

Model: mLAN8E

Kategoria: Sprzęt muzyczny

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

čeština: Yamaha mLAN8E Uživatelský manuál
español: Yamaha mLAN8E Manual de usuario
italiano: Yamaha mLAN8E Manuale utente
Deutsch: Yamaha mLAN8E Benutzerhandbuch
svenska: Yamaha mLAN8E Användarmanual
português: Yamaha mLAN8E Manual do usuário
français: Yamaha mLAN8E Manuel utilisateur
Türkçe: Yamaha mLAN8E Kullanım kılavuzu
English: Yamaha mLAN8E User manual
dansk: Yamaha mLAN8E Brugermanual
русский: Yamaha mLAN8E Руководство пользователя
suomi: Yamaha mLAN8E Ohjekirja
Nederlands: Yamaha mLAN8E Handleiding
română: Yamaha mLAN8E Manual de utilizare

Yamaha mLAN8E Instrukcja obsługi

Yamaha mLAN8E Instrukcja obsługi

w innych językach

Powiązane dokumenty