AMP Lighting APL-3016-4-B-BZ Instrukcja instalacji

Marka
AMP Lighting
Model
APL-3016-4-B-BZ
Typ
Instrukcja instalacji

Niniejsza instrukcja jest również odpowiednia dla

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
ScoutPro Path Light
APL-3016-4-B-BZ
AMP
®
ScoutPro Path Light
APL-3016-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
Install Stake
A. (1) Fixture Body
B. (1) Lens
C. (3) Set Screws
23”
11”
5
1/2
”
4”
Board
Stake
Soil
Ground
Determine the desired location for
mounting the xture. Hammer the
stake into the ground until ange
of stake is ush to grade. To avoid
damage to the stake, place a board on
top of the stake while hammering.
NOTE: If the ground is hard and the
stake is difcult to install, make a
crosscut in the ground using a at
shovel.
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP
®
ScoutPro Path Light
APL-3016-4-B-BZ
Install G4 Bi-Pin
Install Lens
G4 Bulb
Socket
Insert the G4 Bi-Pin with the correct
wattage and type as marked on
luminaire label. Push the Bi-Pin into
place.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT TOUCH G4 Bi-Pin with
bare hands. Use soft cloth to handle
lamp.
Set Screw
Bolt
Shade
Lens
Attach the lens over the bolts in
the shade and secure with the set
screws.
[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP
®
ScoutPro Path Light
APL-3016-4-B-BZ
Install Fixture to Stake
Wire Connections
Stake
Wireway Slot
Fixture
Fixture Wire
Ground
Soil
Clear an area in the ground at
the wireway slot on top of the
stake. Lay the xture wire into the
wireway slot and thread the xture
onto the stake.
If the assembly does not look
straight, adjust by pushing or
pulling on the stake only.
Use a bubble level against the side
of the stem to ensure that the stem
is perpendicular to the ground.
Main Low Voltage
Supply Cable
Wire Connectors
Pigtail
Supply Wire from
Fixture Body
Strip both leads from xture body. Using two wire connectors (sold
separately), connect the leads from xture body to the main low
voltage supply cable leads.
INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
Install/Replace Bi-Pin
AMP
®
ScoutPro Path Light
APL-3016-4-B-BZ
Loosen the set screws and remove the lens to expose the G4 Bi-Pin and
replace it with the correct wattage and type marked on the luminaire label.
Then reinstall the lens and secure with set screws.
IMPORTANT: G4 Bi-Pin must be protected from moisture and dust at all
times. Always reinstall the lens when removed.
–6––6–
[email protected] • 813.978.3900
–7–
IS-APL-3016-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMP Lighting APL-3016-4-B-BZ Instrukcja instalacji

Marka
AMP Lighting
Model
APL-3016-4-B-BZ
Typ
Instrukcja instalacji
Niniejsza instrukcja jest również odpowiednia dla
Pobierz PDF
raport

w innych językach

Powiązane artykuły

Inne dokumenty