© Copyright 2008 Smart-AVI, All Rights Reserved
Notice
The information contained in this document is
subject to change without notice. Smart-AVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and fitness for any particular
purpose.
Smart-AVI will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material.
No part of this document may be photocopied,
reproduced or translated into another language with
out prior written consent from Smart-AVI.
For the complete manual, visit www.smartavi.com.
Use a single CAT5 to broadcast
IR up to 1000ft away(333m)
HDC-IR
www.smartavi.com
User Manual
2840 N. Naomi Ave.
Burbank, California 91504
Phone: (818) 565-0011
Facsimile: (818) 565-0020
Technical Specifications
METI
IR Eye input
IR Frequency Range 30 KHz to 80KHz
Capture Distance Up to 25ft
Cable Connector
IR Signal Indicator Green LED
Power Requirements 5VDC 30mA
Signal Type
TTL
IR Emitter output
IR Frequency Range
30KHz to 80KHz
Emitter Distance
Up to 10’
Cable Connector 3.5mm mono jack
IR Signal Indicator
Box
Power Requirments 12VDC 1A single power up to 250’
Cable Link CAT5 568A or 568B
Dimension
Weight
.25lb (0.9 Kg.)
HDC-IR SPECIFICATIONS
3.5mm stero jack
Red LED
2.5”x2.5”x1.0”
Introduction
The HDC-IR range of products allow the extension
of Infra Red control signals using single CAT5 UTP
(category 5, unshielded twisted pair) cable. The
HDC-IR is the first product for this application.
Features
Uses easy to install, inexpensive CAT5.
Output reaches up to 1000 feet (300 m).
Sends IR and Power signals over CAT5
Bi-directional IR.
High ground loop immunity.
Built-in lightning, power surge and transient
protection.
Remote Units come with Buffered Outputs.
Compact Enclosure.
Optional power supply for remote unit.
Fully compliant with standard modulated IR
and the latest IRDA.
Fully transparent path for all protocols and
data transfers.
What’s in the box?
HDC-IR
Please check the contents of the package before
beginning installation.
Installation Diagram
ytQ metI noitpircseD
1
1
1
1
DEL-MS
EYE-MS
2
Installation Instructions
Operating Instructions
Once installation is completed, verify that the power is
present at all devices in the system. The peripheral
devices should be ready for use.
sdradnatSgniriW5TAC
#niAP865AIT/AIBE865AIT/AIE
e1pirtsnee
rghtiwetiheWpirtsegnarohtiwetihW
n2eergdilosroepirtsetihwhtiwneerG egna
rodilosroepirtsetihwhtiweg
narO
3epirtsegnarohtiwetihW epirtsneerghtiwetihW
e4ulb
dilosroepirtsetihwhtiweulB eulbdilosroepirtsetihwhtiweulB
e5pirtseulbhtiwetiheWpir
tseulbhtiwetihW
6 egnarodilosroepirtsetihwhtiwegnarO dilosroepirtsetihwhtiwneerG
n7worbdilosroepirtsnworbhtiwetihW nworbdilosropirtsnworbhtiwetihW
n8worbdilosr
oepirtsetihwhtiwnworB nworbdilosroepirtsetihwhtiwnworB
Connecting the IR
Use the Diagram for the IR connection.
Connecting the Transmitter
1. Connect the IR LED to the IR window on the source
device.
2. Connect power supply to the unit. Observe LED
lighting up indicating power present.
Connecting the Receiver
Connect IR LED to the IR window on the souce device.
2. Connect the IR Eye to the Receiver.
3. Observe LED lighting indicating power present.
Connect the Transmitter to the Receiver
Connect the transmitter to the receiver using
Category 5 UTP cable (Purchased separately). The
CAT 5 UTP cable, if purchased in
bulk, will be wired using 568A or
568B wiring standard. Once
connected, check that the power
LEDs on both the receiver and the
transmitter are on, IR status LED is on and RX LED is
flashing when Remote control is used indicating that
communication is in progress.
HDC-IR-TX
HDC-IR-RX
PS12VD1A
IR Transmitter
IR Receiver
IR Emitter
IR Eye “Optional”
Power supply12VDC1A
Supports any IR Remote Control.
HDC-IR can be used 2 ways,
1. enabling the remote side to control the DVD,
or any other source device. (the IR eye would
be connected at the remote).
2. enabling the source side to turn off or on the
remote TV/Monitor (the IR eye would be
connected at the source.
-
1
-
2
