Raven AutoBoom Instrukcja instalacji

Apache 2004 and Older

Manual # 016-0230-013 REV A 10/06

1

C H A P T E R

INTRODUCTION

Congratulations on your purchase of the Raven Autoboom system! This system is designed

to provide worry-free operation of your hydraulically controlled booms. The following in-

structions are designed to assist you in the proper installation of the system hardware. The

Autoboom hydraulic installation process is fairly straight forward and prior knowledge of

the machine’s hydraulic system is beneficial. Be sure to carefully follow the safety and

installation instructions of this manual. Be sure to pay careful attention to the hydraulics

installation. Improper installation could result in a system that does not work correctly.

Following the completion of the hardware installation, refer to the instructions in the Power

Glide, Power Glide Plus and Ultra Glide Calibration and Operator’s manual.

This manual gives the installation instructions for the Power Glide, Power Glide Plus, and

Ultra Glide Systems. Be sure to identify which system you have and follow only the instruc-

tions for that system.

Apache 2004 and Older Autoboom Installation Manual

2

Basic Kit

Contents

PowerGlide System

w Hardware Installation Kit 117-0230-013

w Hydraulic Hose and Fitting Kit

w Hydraulic Valve and Mounting Hardware

w Axle Mounting Brackets and Mounting

w Axle Kit 117-0131-

w 2 Axles

w Controller Kit 117-0137-022

w In-Cab Controller

w Main Harness Cable

w Power Cable (Controller to Switched Power Source)

PowerGlide Plus System

w Hardware Installation Kit 117-0231-013

w Wheel Kit

w Hydraulic Hose and Fitting Kit.

w Hydraulic Valve and Mounting Hardware

w Controller Kit 117-0137-023

w Main Harness Cable

w Power Cable (Controller to Switched Power Source)

w CAN Node

UltraGlide System

w Hardware Installation Kit 117-0232-013

w Ultrasonic Sensors

w Hydraulic Hose and Fitting Kit.

w Hydraulic Valve and Mounting Hardware

w Controller Kit 117-0137-023

w Main Cable

w Power Cable (Controller to Switched Power Source)

w CAN Node

Installation Manual Machine Reference

Make: Apache

Model: 700 and 800 Series

Year: 2004 and older

Serial Number:

Manual # 016-0230-013 REV A 10/06

3

C H A P T E R

SAFETY

This section is divided between general safety precautions, specific safety mea-

sures in respect to the hydraulic and electrical system, and machine driving and

operating safety.

Important: The machine must remain stationary and switched

off, the booms unfolded and supported, while installation or

maintenance is conducted.

Safety Precautions

When working with or near a machine with Autoboom installed, the following

safety measures must be observed. The operator must:

w Be alert and aware of surroundings.

w Not operate Autoboom or any agricultural equipment while under the

influence alcohol or an illegal substance.

w Remain in the operator’s position in the machine at all times when Autoboom

is engaged.

w Disable Autoboom when exiting from the operator’s seat and machine.

w Not drive the machine with Autoboom enabled on any public thorough-

fare or main road.

w Determine and remain a safe working distance from other individuals.

The operator is responsible for disabling Autoboom when the safe work-

ing distance has diminished.

w Ensure Autoboom is disabled prior to starting any maintenance work on

Autoboom or machine.

Installation

Safety

Requirements

Apache 2004 and Older Autoboom Installation Manual

4

Hydraulic Safety Precautions

Important: Sprayer hydraulics are under pressure. Never

attempt to open or work on a hydraulic system with the

equipment running. Care should always be taken when first

opening a system that was previously pressurized.

When disconnecting the hydraulic hoses or when purging is required, be aware

that the hydraulic oil within the machine system may be extremely hot and under

high pressure. Caution must be exercised. Any work carried out on the hydraulic

system must be performed in accordance with the machine manufacturer’s ap-

proved maintenance instructions. Raven industries recommends that appropriate

protective equipment be worn when working on the hydraulic system.

Important: It is imperative that when installing Autoboom

hydraulics, performing diagnostics, maintenance, or routine

machine servicing, that all installers and customers ensure

precautions are taken to prevent any foreign material or

contaminants from being introduced into the machine’s

hydraulic system.

Objects or materials that are able to bypass the machine’s hydraulic filtration

system will adversely reduce performance and possibly damage the Autoboom

hydraulic valves.

Electrical Safety Precautions

Do not reverse the power leads. Doing so will cause severe damage to the

equipment. Always ensure the power leads are connected to the correct polarity

as marked. Ensure that the power cable is the last cable to be connected.

Manual # 016-0230-013 REV A 10/06

5

This section outlines the safety requirements used when driving a vehicle using

the Autoboom system.

Areas of Operation

The Autoboom must only be used on private property without public access. It

must only be used within cleared fields. It must not be used when traveling on any

public roads or access ways. Raven Industries advises that users familiarize

themselves with Autoboom operation by first reading the Autoboom Installation

Manual and the PowerGlide, PowerGlide Plus, or UltraGlide Calibration and

Operator’s Manual.

Avoidance of People

Autoboom must not be operated in the vicinity of people. Bystanders must be

well outside of the machine’s path while Autoboom is enabled.

Avoidance of Machinery and Equipment

The Autoboom operator must allow a safe distance between the machine’s path

and other machinery or equipment. To determine a safe distance, take into ac-

count the incorrect operation of the boom management system and the width of

the booms.

Avoidance of Obstacles

Autoboom CANNOT detect obstacles such as fences, trees, or boulders that are

not located within the sensor or wheel path. The machine operator must identify

and avoid obstacles that are not able to be detected by the boom sensors or wheels

while working in a field.

Responsibilities of Operator

The operator must remain in complete control of the machine at all times. Only

when Autoboom is enabled can there be hands-free operation of the booms. The

operator remains fully responsible for the operation of the machine and must re-

main in the operator’s seat at all times while Autoboom is enabled.

Disengaging Boom Control

The operator must naturally lift the booms if an obstacle is in the line of travel and

is not detected by the sensor or wheels. Pressing the “Up” function on the boom

controller will disengage Autoboom if Boom Sense wires have been installed.

Driving Safety

Requirements

Apache 2004 and Older Autoboom Installation Manual

6

We welcome your feedback about this manual. If you have any comments or

suggestions for improvement, please let us know by contacting our Customer

Support Center by any of the following methods:

w Via phone: 1-800-243-5435

w Via mail:

Raven Industries

Flow Control Division

205 E. 6th St.

Sioux Falls, SD 57104

w Via email: [email protected]

Contacting

Raven

Industries

Manual # 016-0230-013 REV A 10/06

7

C H A P T E R

POPULATING AND MOUNTING THE VALVE

Mount valve on center rack below machine manifold

POWER GLIDE

FITTING PORT

9/16" SAE O-Ring (M) Plug LV, RV

9/16" JIC (M) to 9/16" SAE O-Ring (M) LC, RC

9/16" JIC (M) to 3/4" SAE O-Ring (M) P (Filter), T

Apache 2004 and Older Autoboom Installation Manual

8

Power Glide

Dual

Cartridge

Option

1. Remove cavity plug (5A) and port plug (6A).

2. Discard port plug (6A) or keep for future upgrade to Power Glide Plus.

3. Insert cavity plug from port 5A into port 6A.

4. Install mechanical cartridge into port 5A.

Manual # 016-0230-013 REV A 10/06

9

C H A P T E R

HYDRAULIC HOSE & FITTINGS INSTALLATION

Pressure and Tank Lines

Tee into P and T lines on machine manifold

ORIENTATION

P/N HOSE END LOCATION HOSE END LOCATION

214-1000-292 9/16" JIC (F) Left Up Tee 9/16" JIC (F) 90° LC

214-1000-292 9/16" JIC (F) Right Up Tee 9/16" JIC (F) 90° RC

214-1000-126 9/16" JIC (F) P Tee 9/16" JIC (F) 90° P (Filter)

214-1000-126 9/16" JIC (F) T Tee 9/16" JIC (F) 90° T

MACHINE AUTOBOOM VALVE

Apache 2004 and Older Autoboom Installation Manual

10

LC, RC, LV, RV

Tee into Left Up and Right Up Tilt Cylinder Lines.

Manual # 016-0230-013 REV A 10/06

11

Power Glide Hydraulic Schematic

Apache 2004 and Older Autoboom Installation Manual

12

C H A P T E R

POPULATING AND MOUNTING THE VALVE

POWER GLIDE PLUS

&

ULTRA GLIDE

FITTING PORT

9/16" SAE O-Ring (M) Plug LV, RV

9/16" JIC (M) to 9/16" SAE O-Ring (M) LC, RC

9/16" JIC (M) to 3/4" SAE O-Ring (M) P (Filter), T

Manual # 016-0230-013 REV A 10/06

13

NOTE: Ultra Glide - Make sure floating orifice in LC and RC ports are installed

with slot facing out.

Mount valve on center rack below machine manifold

Apache 2004 and Older Autoboom Installation Manual

14

C H A P T E R

HYDRAULIC HOSE & FITTING INSTALLATION

Pressure and Tank Lines

Tee into P and T lines on machine manifold

ORIENTATION

P/N HOSE END LOCATION HOSE END LOCATION

214-1000-292 9/16" JIC (F) Left Up Tee 9/16" JIC (F) 90° LC

214-1000-292 9/16" JIC (F) Right Up Tee 9/16" JIC (F) 90° RC

214-1000-126 9/16" JIC (F) P Tee 9/16" JIC (F) 90° P (Filter)

214-1000-126 9/16" JIC (F) T Tee 9/16" JIC (F) 90° T

MACHINE AUTOBOOM VALVE

Manual # 016-0230-013 REV A 10/06

15

Tee into Left Up and Right Up Tilt Cylinder lines

LC, RC, LV, RV

Apache 2004 and Older Autoboom Installation Manual

16

Power Glide Plus & Ultra Glide Hydraulic Schematic

Manual # 016-0230-013 REV A 10/06

17

C H A P T E R

WHEEL & SENSOR MOUNTING

Wheel

Mounting

Mount axle bracket just beyond boom fold

Apache 2004 and Older Autoboom Installation Manual

18

Sensor

Mounting

Strona się ładuje...

Raven AutoBoom Instrukcja instalacji

Raven AutoBoom Instrukcja instalacji

w innych językach

Inne dokumenty