Hotpoint Ariston AQ7L 05 U Instructions For Installation And Use Manual

Marka: Hotpoint Ariston

Model: AQ7L 05 U

Kategoria: Pralki

Typ: Instructions For Installation And Use Manual

English,1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 4-5

Control panel

Running a wash cycle, 6

Wash cycles and options, 7

Table of wash cycles

Wash options

Detergents and laundry, 8

Detergent

Preparing the laundry

Washing recommendations

Load balancing system

Precautions and advice, 9

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 11

Assistance, 12

WASHING MACHINE

AQUALTIS

AQ7L 05 U

Instructions for

installation and use

Polski,25

Español,13

Downloaded From WashingMachine-Manual.com Manuals

Installation

 This instruction manual should be kept in a safe place

for future reference. If the washing machine is sold,

given away or moved, please ensure the manual is kept

with the machine, so that the new owner may benefit

from the advice contained within it.

 Read these instructions carefully: they contain vital

information relating to the safe installation and operation

of the appliance.

 Inside the pack containing this manual, you will also

find the guarantee and all the details necessary for

installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the

washing machine, make sure it has not been damaged

during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws (used

during transportation) and

the corresponding spacer,

located on the rear part of

the appliance (see figure).

3. Close off the holes using the plastic plugs supplied in

the pack.

4. Keep all the parts in a safe place; they will be needed

again if the washing machine is moved to another

location, to prevent the inside of the appliance being

damaged.

 Packaging materials should not be used as toys for

children.

Levelling

1. Place the washing machine on a flat sturdy floor,

without resting it up against walls or cabinets.

2. If the floor is uneven,

the front feet of the

machine may be adjusted

until it reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

 If the appliance is levelled correctly, it will be more

stable and much less likely to cause vibrations and noise

while it is operating, particularly during the spin cycle.

 If it is placed on carpet or a rug, adjust the feet in such

a way as to allow a sufficient ventilation space

underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

 Before connecting the inlet hose to the water supply,

run the water until it is perfectly clear.

1. Connect the inlet hose

to the machine by

screwing it onto the cold

water inlet of the

appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

2. Connect the inlet hose

by screwing it to a cold

water tab using a 3/4 gas

threaded connection (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical data table (see next

page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand or old inlet hoses; use the

products supplied with the machine.

Downloaded From WashingMachine-Manual.com Manuals

65 - 100 cm

Connecting the drain hose

Connect the drain hose to

drain duct piping or a wall

drain located between 65

and 100 cm above the

floor, making sure it is not

bent at all.

Alternatively, rest the drain

hose on the side of a

washbasin or bathtub,

fastening the duct

supplied to the tap (see

figure).

The free end of the hose

should not be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

 the socket is earthed and complies with all applicable

laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

appliance. If this is not the case, have the socket or

the plug replaced.

 The machine must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain, storms and other weather

conditions.

 The mains socket must remain within easy reach after

the washing machine has been installed.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable and plug must only be

replaced by authorised technicians.

Warning! The company shall not be held responsible in

the event that these regulations are not respected.

Technical data

Model AQ7L 05 U

Dimensions

width 59.5 cm

height 85 cm

depth 58 cm

Capacity from 1 to 7 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed up to 1000 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme ; temperature 60°C;

using a load of 7 kg.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Downloaded From WashingMachine-Manual.com Manuals

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

Description of the machine

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside the

machine and can be

accessed by opening the

door.

For more information on

detergent measures, please

refer to the chapter entitled

Detergents and laundry.

Note: stick the label showing

the wash cycle descriptions and options on the front of

the detergent dispenser drawer. You will find the sticker

in the pack containing this manual.

1. pre-wash compartment:

use powder detergent.

 Before pouring in the

detergent, make sure that

extra compartment 3 has

been removed.

2. main wash compartment:

use powder or liquid

detergent. If using the latter

type of detergent, we

recommend it is poured into the drawer immediately

before you start the washing machine.

3. extra compartment: Bleach

 The use of extra compartment 3 excludes the pre-

wash function.

washing additives compartment: for fabric softener or

liquid additives. We recommend that the maximum level

indicated by the grille is not exceeded, and that

concentrated fabric softeners are diluted.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after a few minutes if no activity

is detected. Press the ON-OFF button briefly and wait

for the machine to start up again.

Downloaded From WashingMachine-Manual.com Manuals

TEMPERATURE button

WASH CYCLE

SELECTOR knob

OPTION buttons with

indicator lights

DOOR LOCKED

indicator light

START/PAUSE

button with indicator

light

WASH

CYCLE

PHASE

icons

SPINbutton

DELAYED

START

button

CONTROL PANEL

LOCK button with

indicator light

Button withON/OFF

indicator light

ECO indicator light

OPTION buttons with

indicator lights

TEMPERATURE

indicator lights

SPIN

indicator lights

DELAYED START

indicator lights

Control panel

Button with ON/OFF indicator light: press this briefly

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off

the washing machine during the wash cycle, press and

hold the button for approximately 3 seconds; if the

button is pressed briefly or accidentally the machine will

not switch off. If the machine is switched off during a

wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the Table of wash cycles.

The knob will not move during the wash cycle.

TEMPERATURE button: press to modify or exclude

the temperature setting; the value will be identified by

the indicator lights above it (see Running a wash

cycle).

SPIN CYCLE button: press to modify or exclude the

spin cycle; the value will be identified by the indicator

lights above it (see Running a wash cycle).

DELAYED START button: press to set a delayed

start for the selected wash cycle; the delay time will be

identified by the indicator lights above (see Running a

wash cycle).

OPTION buttons with indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see Running a wash

cycle).

WASH CYCLE PHASE icons: these illuminate to

indicate the progress of the wash cycle (Wash 

Rinse  Spin  Drain ).

The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To pause

the wash cycle, press the button again; the indicator

light will flash in an orange colour. If the Door locked

indicator light is switched off, the door may be

opened. To start the wash cycle from the point at which

it was interrupted, press the button again.

DOOR LOCKED indicator light: indicates that the

porthole door is locked. To open the door, pause the

wash cycle (see Running a wash cycle).

CONTROL PANEL LOCK button with indicator

light: to activate or deactivate the control panel lock,

press and hold the button for approximately 2 seconds.

when the indicator light is illuminated, the control panel is

locked. This means it is possible to prevent wash cycles

from being modified accidentally, especially where there

are children in the home.

ECO indicator light: the icon lights up when, after

altering the washing parameters, an energy saving of at

least 10% is made. Furthermore, before the machine

enters Standby mode, the icon will light up for a few

seconds; when the machine is switched off the

estimated energy saving will be around the 80% mark.

Downloaded From WashingMachine-Manual.com Manuals

WARNING: before you use the washing machine for

the first time, run a wash cycle with detergent and no

laundry, using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the button.

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the button will then

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent

into the relevant compartments as described in

Description of the machine.

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH

CYCLE SELECTOR KNOB right or left, until you have

selected the desired wash cycle. A temperature and

spin speed is set for each wash cycle; these may be

adjusted.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons on the control panel:

Modify the temperature and/or spin

speed.

The machine automatically displays the maximum

temperature and spin speed values set for the

selected cycle, or the most recently-used settings if

they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash ( ) setting is reached. The

spin speed may be progressively reduced by pressing

the button, until it is completely excluded ( ). If

these buttons are pressed again, the maximum

values are restored.

 Exception: if the Cottons programme is selected,

the temperature can be increased up to a value of

90°C.

Set a delayed start.

To set the "delayed start" option for the program you

have selected, press the button until the indicator light

for the desired delay time is illuminated.

The sixth time the button is pressed, the function will

be disabled.

N.B.: once the START/PAUSE button is pressed the

"delayed start" indicator light will flash

(the time delay value may only be changed by

decreasing the time).

Modify the cycle settings.

Press the OPTION buttons to customise the wash

cycle in accordance with your own requirements.

 Press the button to activate the option; the

corresponding indicator light will switch on.

 Press the button again to disable the option; the

indicator light will switch off.

 If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

 If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the

indicator light corresponding to the button will remain

lit in a constant manner.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the DOOR LOCKED indicator light

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress.

To change a wash cycle once it has already started,

pause the washing machine by pressing the START/

PAUSE button; then select the desired cycle and

press the START/PAUSE button again.

To open the door during a wash cycle, press the

START/PAUSE button; if the DOOR LOCKED

indicator light is switched off you may open the door.

Press the START/PAUSE button again to restart the

wash cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may

be opened immediately. If the START/PAUSE indicator

light is flashing, press the button to end the cycle.

Open the door, unload the laundry and switch off the

machine.

 If you wish to cancel a cycle which has already begun,

press and hold the button until the cycle stops and

the machine switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to

wash even the most valuable and delicate garments in

complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you

wash quilts and padded items with an outer layer made

using synthetic material.

Running a wash cycle

Downloaded From WashingMachine-Manual.com Manuals

Wash options

Super Wash

This option offers a high-performance wash due to the

greater quantity of water used in the initial phase of the

cycle, and due to the increased wash cycle duration, is

particularly useful for the removal of stubborn stains. It

can be used with or without bleach. If you desire

bleaching, insert the extra

tray compartment (3) into

compartment 1. When

pouring in the bleach, be

careful not to exceed the

max level marked on the

central pivot (see figure).

To bleach laundry without

carrying out a full wash

cycle, pour the bleach into

the extra compartment 3,

select the "Rinse" cycle

and activate the "Super Wash" option .

 It cannot be used in conjunction with , , , , ,

, , .

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine

drum will rotate slowly; the Easy Iron and START/

PAUSE indicator lights will flash. To end the cycle press

the START/PAUSE button or the Easy Iron button.

For the Silk wash cycle, the machine will end the

cycle while the laundry is soaking and the Easy

Iron indicator light will flash. To drain the water so that

the laundry may be removed, press the START/PAUSE

button or the Easy Iron button.

 It cannot be used in conjunction with , , , , .

Time Saver

If you select this option, the wash cycle duration will be

reduced by 30%-50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

 It cannot be used in conjunction with , , , ,

, , , , .

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal residual detergent removal is

guaranteed. It is particularly useful for skin which is

sensitive to detergents. We recommend this option is

used with a full load of washing, or when a large amount

of detergent is required.

 It cannot be used in conjunction with , , .

Wash cycles and options

Table of wash cycles

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle with a temperature of 40°C.

Icon Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergent and additives Max.

load

(kg)

Cycle

duration

Detergent

for wash

Fabric

softener Bleach

Cottons wash cycles

Cottons with pre-wash

(Add detergent to the relevant compartment). 90° 1000 ll

-7174

Cottons (1): heavily soiled whites and resistant colours. 60°

(Max. 90°) 1000 lll

7153

Cottons (2): heavily soiled whites and delicate colours. 40° 1000 lll

7148

Coloured Cottons (3) 40° 1000 lll

792

Shirts 40° 600 lll

269

Jeans 40° 800 ll

-3,5 80

Special programmes

Baby: heavily soiled delicate colours 40° 800 lll

3118

Durable Synthetics 60° 800 lll

385

Delicate Synthetics 40° 800 lll

374

"Bed & Bath" for bedlinen and towels. 60° 1000 lll

795

Duvets: for down-stuffed garments. 30° 1000 ll

-294

Silk: for garments in silk and viscose, lingerie. 30° 0 ll

-155

Wool: for wool, cashmere, etc. 40° 600 ll

-1,5 55

Mix 30': to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand) 30° 800 ll

-330

Partials wash cycles

Rinse -1000 -ll

736

Spin -1000 - - - 716

Drain -0- - - 72

Downloaded From WashingMachine-Manual.com Manuals

Detergents and laundry

Detergent

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Measuring out the detergent carefully will avoid wastage

and help to protect the environment: although they are

biodegradable, detergents still contain ingredients which

alter the balance of nature.

We recommend the following:

 use powder detergents for white cotton garments and

pre-washing.

 use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

 use gentle liquid detergents for wool and silk

garments.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside

the drum - before the wash cycle begins. In the latter

case, it will not be possible to select the Cottons with

pre-wash cycle.

 Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

 Shake out the garments before loading them into the

machine.

 Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

 Empty all pockets and check the buttons;

 Do not exceed the values listed in the Table of wash

cycles, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Shirts: use the special Shirts wash cycle to wash

shirts in different fabrics and colours to guarantee they

receive the best possible care.

Jeans: use the special Jeans wash cycle for all

denim garments; turn inside out before washing and use

a liquid detergent.

Baby: use the special Baby wash cycle to remove

the remove the soiling typically caused by babies, while

removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suffering allergic

reactions. The cycle has been designed to reduce the

amount of bacteria by using a greater quantity of water

and optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle,

the machine will slowly rotate the drum; to end the cycle

press the START/PAUSE button.

Silk: use the special Silk wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the Silk wash cycle. These should

be folded and placed inside the bag provided.

Wool: Hotpoint/Ariston is the only washing machine

brand to have been awarded the prestigious Woolmark

Platinum Care endorsement (M.0508) by the Woolmark

Company, which means that all woollen garments may

be washed in the washing machine, even those which

state hand wash only on the label. The Wool

wash cycle can be used to wash all woollen garments in

the washing machine while guaranteeing optimum

performance.

Duvets: to wash single duvets (the weight of which

should not exceed 2 kg), cushions or clothes padded

with goose down such as puffa jackets, use the special

Duvets wash cycle. We recommend that duvets

are placed in the drum with their edges folded inwards

(see figure) and that no more than ¾ of the total volume

of the drum is used. To achieve the best results, we

recommend that a liquid detergent is used and placed

inside the detergent dispenser drawer.

Quilts: to wash quilts with a synthetic outer layer, use

the bag provided and set the wash cycle to Duvets .

Bedlinen and towels: use the Bed & Bath cycle

to wash laundry from all over the house; this optimises

fabric softener performance and helps you save time and

energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If

the load is excessively unbalanced, the washing

machine performs the distribution process instead of

spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Downloaded From WashingMachine-Manual.com Manuals

Precautions and tips

 The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 the machine must only be used by adults, in

accordance with the instructions given in this manual.

 Do not touch the machine when barefoot or with wet

or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water

using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is

freed from its stop position;

pull downwards until you

hear a click, which

indicates that the door is

now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Downloaded From WashingMachine-Manual.com Manuals

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

 Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser

drawer

To remove the drawer, press

lever (1) and pull the drawer

outwards (2) (see figure).

Wash it under running

water; this procedure should

be repeated frequently.

Caring for your appliance drum

 Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

 Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the machine

by first pressing it in the centre and then pushing

downwards on both sides until you can remove it (see

figures);

2. position a container so

that it will collect the water

which flows out

(approximately 1.5 l) (see

figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

Care and maintenance

Downloaded From WashingMachine-Manual.com Manuals

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre

(see Assistance), make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water.

The washing machine door

remains locked.

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The icons corresponding to the

Phase in progress flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washing machine door

remains locked.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or not enough to make

contact.

 There is no power in the house.

 The door is not closed properly.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 If you have selected the Baby  cycle or the Easy iron  option, when

the wash cycle has finished the machine will slowly rotate the drum; to end

the cycle press the START/PAUSE button or the Easy iron  button. If

you have selected the Silk  wash cycle, the machine will end the cycle

while the laundry is soaking; to drain the water so that the laundry may be

removed, press the START/PAUSE button or the Easy iron  button.

 The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see Installation).

 The free end of the hose is under water (see Installation).

 If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to fill

with water and drain continuously. Special anti-draining valves are available

in shops and help to prevent this inconvenience.

 The wall drainage system is not fitted with a breather pipe.

 The wash cycle does not include draining: Some wash cycles require the

drain phase to be started manually (see Wash cycles and options).

 The Easy iron option is enabled: to complete the wash cycle, press the

START/PAUSE button (Wash cycles and options).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The machine is not level (see Installation ).

 The machine is trapped between cabinets and walls (see Installation).

 The load is unbalanced (see Detergents and laundry).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser is blocked (to clean it, see Care and

maintenance).

 The drain hose is not fixed in place properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

 The detergent is not suitable for machine washing (it should display the text

for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

 Perform the manual unlocking procedure (see Precautions and tips).

Downloaded From WashingMachine-Manual.com Manuals

Before calling for Assistance:

 Check whether you can solve the problem by yourself (see Trouble shooting);

 Restart the wash cycle to check whether the problem has been solved;

 If it has not, contact the Authorised Technical Assistance Service.

 If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.

 Always request the assistance of authorised technicians.

Please have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

Assistance

Downloaded From WashingMachine-Manual.com Manuals

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Datos técnicos

Descripción de la máquina, 16-17

Panel de control

Cómo efectuar un ciclo de lavado, 18

Programas y opciones, 19

Tabla de Programas

Opciones de lavado

Detergentes y ropa, 20

Detergente

Preparar la ropa

Consejos sobre el lavado

Sistema de equilibrado de la carga

Precauciones y consejos, 21

Seguridad general

Eliminación

Apertura manual de la puerta

Mantenimiento y cuidados, 22

Interrumpir el agua y la corriente eléctrica

Limpiar la máquina

Limpiar el contenedor de detergentes

Cuidar el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Anomalías y soluciones, 23

Asistencia, 24

LAVADORA

AQUALTIS

AQ7L 05 U

Instrucciones para la

instalación y el uso

Downloaded From WashingMachine-Manual.com Manuals

Instalación

 Es importante conservar este manual para poder

consultarlo en cualquier momento. En el caso de venta,

cesión o traslado, controle que permanezca junto con la

lavadora.

 Lea atentamente las instrucciones: ellas contienen

importante información sobre la instalación, el uso y la

seguridad.

 En el sobre que contiene este manual encontrará,

además de la garantía, piezas que servirán para la

instalación.

Desembalaje y nivelación

Desembalaje

1. Una vez desembalada la lavadora, controle que no

haya sufrido daños durante el traslado.

Si estuviera dañada no la conecte y llame al revendedor.

2. Quite los 4 tornillos de

protección para el

transporte y el

correspondiente

distanciador, ubicados en

la parte posterior (ver la

figura).

3. Cierre los orificios con los tapones de plástico

contenidos en el sobre.

4. Conserve todas las piezas porque si la lavadora

tuviera que ser trasladada nuevamente, se deberían

volver a colocar para evitar daños internos.

 Los embalajes no son juguetes para los niños.

Nivelación

1. Instale la lavadora sobre un piso plano y rígido, sin

apoyarla en las paredes ni en los muebles.

2. Compense las

irregularidades

desenroscando o

enroscando las patas

hasta que la máquina

quede en posición

horizontal (no debe estar

inclinada más de 2

grados).

 Una cuidadosa nivelación brinda estabilidad y evita

vibraciones y ruidos, sobre todo durante el centrifugado.

 Cuando se instala sobre moquetas o alfombras, regule

las patas para que, debajo de la lavadora, quede un

espacio suficiente para la ventilación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de agua

 Antes de conectar el tubo de alimentación a la red

hídrica, haga correr agua hasta que sea límpida.

1. Conecte el tubo de

alimentación a la máquina

enroscándolo en la toma

de agua correspondiente

ubicada en la parte

posterior derecha (arriba)

(ver la figura).

2. Conecte el tubo de

alimentación enroscándolo

a un grifo de agua fría con

la boca roscada de 3/4 gas

(ver la figura).

3. Controle que en el tubo no hayan pliegues ni

estrangulaciones.

 La presión de agua del grifo debe estar comprendida

dentro de los valores contenidos en la tabla de Datos

técnicos (ver la página correspondiente).

 Si la longitud del tubo de alimentación no es la

suficiente, diríjase a un negocio especializado o a un

técnico autorizado.

 No utilice nunca tubos de carga usados o viejos, utilice

siempre los suministrados con la máquina.

Downloaded From WashingMachine-Manual.com Manuals

65 - 100 cm

Conexión del tubo de descarga

Conecte el tubo de

descarga a una tubería de

descarga o a una

descarga de pared

ubicadas a una distancia

del piso comprendida entre

65 y 100 cm., evitando

siempre plegarlo.

Una alternativa es apoyar

el tubo de descarga en el

borde de un lavamanos o

de una bañera, uniendo la

guía suministrada con el

aparato, al grifo (ver la

figura).

El extremo libre del tubo

de descarga no debe

permanecer sumergido en

el agua.

 No se aconseja utilizar tubos de prolongación, si fuera

indispensable hacerlo, la prolongación debe tener el

mismo diámetro del tubo original y no superar los 150

cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

 la toma tenga la conexión a tierra y haya sido hecha

según las normas legales;

 la toma sea capaz de soportar la carga máxima de

potencia de la máquina indicada en la tabla de Datos

técnicos (ver al costado);

 la tensión de alimentación esté comprendida dentro

de los valores indicados en la tabla de Datos técnicos

(ver al costado);

 la toma sea compatible con el enchufe de la

máquina. Si no es así, sustituya la toma o el enchufe.

 La máquina no debe ser instalada al aire libre, ni

siquiera si el lugar está protegido, ya que es muy

peligroso dejarla expuesta a la lluvia o a las tormentas.

 Una vez instalada la máquina, la toma de corriente

debe ser fácilmente accesible.

 No utilice prolongaciones ni conexiones múltiples.

 El cable no debe estar plegado ni sufrir compresiones.

 El cable de alimentación y el enchufe deben ser

sustituidos sólo por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas no sean

respetadas.

Datos técnicos

Modelo AQ7L 05 U

Dimensiones

ancho 59,5 cm.

altura 85 cm.

profundidad 58 cm.

Capacidad de 1 a 7 kg.

Conexiones

eléctricas

ver la placa de características

técnicas aplicada en la máquina

Conexiones

hídricas

presión máxima 1 MPa (10 bar)

presión mínima 0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad de

centrifugado máxima 1000 r.p.m.

Programas de

control según la

norma EN 60456

programa ; temperatura 60ºC;

efectuado con 7 kg. de carga.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 89/336/CEE del 03/05/89

(Compatibilidad Electromagnética) y

sucesivas modificaciones

- 2002/96/CE

- 2006/95/CE (Baja Tensión)

Downloaded From WashingMachine-Manual.com Manuals

PANEL DE

CONTROL

PUERTA

MANIJA DE

LA PUERTA

ZÓCALO

PATAS REGULABLES

Descripción de la máquina

PUERTA

Para abrir la puerta utilice

siempre la manija

correspondiente (ver la

figura).

CONTENEDOR DE DETERGENTE

El contenedor de

detergentes se encuentra

en el interior de la máquina y

se accede a él abriendo la

puerta.

Para la dosificación de

detergente, ver el capítulo

Detergentes y ropa.

Nota: adhiera al contenedor

de detergente el adhesivo

con la descripción de los

programas y las opciones. El adhesivo se encuentra en

el sobre que contiene este manual.

1. cubeta para el prelavado:

utilice detergente en polvo.

 Antes de verter el

detergente, verifique que no

esté colocada la cubeta

adicional 3.

2. cubeta para el lavado:

utilice detergente en polvo o

líquido. En este último caso

se recomienda verterlo un

instante antes de la puesta

en marcha de la lavadora.

3. cubeta adicional: Blanqueador

 El uso de la cubeta adicional 3 excluye el

prelavado.

cubeta para aditivos: para suavizante o aditivos

líquidos. Se recomienda no superar nunca el nivel

máximo indicado por la rejilla y diluir los suavizantes

concentrados.

Modalidad de stand by

Esta lavadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está dotada

de un sistema de auto-apagado (stand by) que, en caso

de no funcionamiento, se activa pasados algunos

minutos. Presionar brevemente el botón ON/OFF y

esperar que la máquina se active.

Downloaded From WashingMachine-Manual.com Manuals

Panel de control

Botón con piloto ON/OFF: presione brevemente el

botón para encender o apagar la máquina. El piloto

verde indica que la máquina está encendida. Para

apagar la lavadora durante el lavado, es necesario

mantener presionado el botón durante más tiempo,

aproximadamente 3 seg.; si se presiona en forma más

breve o accidental, la máquina no se apagará. Si la

máquina se apaga durante un lavado en curso, dicho

lavado se anulará.

Mando de PROGRAMAS: se puede girar en ambas

direcciones. Para elegir el programa más apropiado,

consulte la Tabla de programas.

Durante el lavado, el mando no se mueve.

Botón TEMPERATURA: presiónelo para modificar o

excluir la temperatura; el valor está indicado por los

pilotos que se encuentran encima (ver Cómo realizar un

ciclo de lavado).

Botón CENTRIFUGADO: presiónelo para modificar

o excluir la centrifugación; el valor está indicado por los

pilotos que se encuentran encima (ver Cómo realizar un

ciclo de lavado).

Botón COMIENZO RETRASADO: presiónelo para

fijar el comienzo retrasado del programa elegido; el valor

del retraso está indicado por los pilotos que se

encuentran encima (ver Cómo efectuar un ciclo de

lavado).

Botones con Pilotos OPCIONES: presiónelos para

seleccionar las opciones disponibles. El piloto

correspondiente a la opción seleccionada permanecerá

encendido (ver Cómo efectuar un ciclo de lavado).

Iconos FASES DE LAVADO: se iluminan para indicar el

avance del ciclo (Lavado  Enjuague 

Centrifugado  Desaguado ).

El mensaje se ilumina cuando ha finalizado el ciclo.

Botón con piloto START/PAUSE: cuando el piloto verde

centellea lentamente, presione el botón para que

comience el lavado. Una vez que el ciclo ha

comenzado, el piloto se mantiene fijo. Para poner en

pausa el lavado, presione nuevamente el botón; el piloto

centelleará con un color anaranjado. Si el piloto

Bloqueo de la puerta está apagado, se podrá abrir

la puerta.

Para que el lavado se reanude a partir del momento en

el cual fue interrumpido, presione nuevamente el botón.

Piloto BLOQUEO DE LA PUERTA: indica que la

puerta está bloqueada. Para abrir la puerta es necesario

poner el ciclo en pausa (ver Cómo efectuar un ciclo de

lavado).

Botón con piloto BLOQUEO DE BOTONES: para

activar o desactivar el bloqueo del panel de control,

mantenga presionado el botón durante 2 segundos

aproximadamente. El piloto encendido indica que el

panel de control está bloqueado. De este modo, se

evitan modificaciones accidentales de los programas,

sobre todo si en la casa hay niños.

Piloto ECO: el ícono se encenderá cuando,

modificando los parámetros de lavado, se obtenga un

ahorro de energía del 10% como mínimo. Además,

antes que la máquina entre en la modalidad "Stand by",

el icono se encenderá unos pocos segundos; con la

máquina apagada la recuperación energética estimada

será de aprox. el 80%.

Botón TEMPERATURA

Mando de

PROGRAMAS

Botones con Pilotos

OPCIONES

Piloto BLOQUEO

DE LA PUERTA

Botón con piloto

START/PAUSE

Iconos FASES

DE LAVADO

Botón CENTRIFUGADO

Botón COMIENZO

RETRASADO

Botón con piloto

BLOQUEO DE

BOTONES

Botón con piloto

ON/OFF

Piloto

ECO

Botones con

Pilotos

OPCIONES

Pilotos TEMPERATURA Pilotos

CENTRI-

FUGACIÓN

Pilotos COMIENZO RETRASADO

Downloaded From WashingMachine-Manual.com Manuals

NOTA: la primera vez que se utiliza la lavadora, realice

un ciclo de lavado sin ropa pero con detergente,

seleccionando el programa algodón 90º sin prelavado.

1. ENCENDER LA MÁQUINA. Presione el botón .

Todos los pilotos se encenderán durante 1 segundo y

luego permanecerá encendido en forma fija el piloto

del botón , el piloto START/PAUSE centelleará

lentamente.

2. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,

cuidando no superar la cantidad de carga indicada en

la tabla de programas de la página siguiente.

3. DOSIFICAR EL DETERGENTE. Extraiga el

contenedor y vierta el detergente en las cubetas

correspondientes como se explica en Descripción de

la máquina.

4. CERRAR LA PUERTA.

5. ELEGIR EL PROGRAMA. Gire el MANDO DE

PROGRAMAS hacia la derecha o hacia la izquierda

hasta seleccionar el programa deseado; se asociarán

al mismo, una temperatura y una velocidad de

centrifugado que luego se pueden modificar.

6. PERSONALIZAR EL CICLO DE LAVADO. Utilice

los botones correspondientes del panel de control:

Modifique la temperatura y/o el

centrifugado.

La máquina muestra automáticamente la temperatura

y la centrífuga máximas previstas para el programa

fijado o las últimas seleccionadas si son compatibles

con el programa elegido. Presionando el botón se

disminuye progresivamente la temperatura hasta llegar

al lavado en frío ( ). Presionando el botón se

disminuye progresivamente el centrifugado hasta su

exclusión ( ). Si se presionan una vez más los

botones, se volverá a los valores máximos previstos.

 Excepción: cuando se selecciona el programa

ALGODÓN, la temperatura se puede aumentar hasta

90°.

Seleccionar el comienzo retrasado.

Para seleccionar el inicio diferido del programa

elegido, presione varias veces el botón hasta que se

encienda el piloto correspondiente al retraso deseado.

La sexta vez que se presione el botón, la función se

desactivará.

Nota: Una vez presionado el botón START/PAUSE el

piloto correspondiente al retraso fijado centelleará (el

valor del retraso se podrá modificar sólo

disminuyéndolo).

Modificar las características del

ciclo.

Presione los botones OPCIONES para personalizar el

lavado según sus exigencias.

 Presione el botón para activar la opción; se

encenderá el piloto correspondiente.

 Presione nuevamente el botón para desactivar la

opción; el piloto se apagará.

 Si la opción seleccionada no es compatible con el

programa elegido, la incompatibilidad se indicará con

el centelleo del piloto y una señal sonora (3 sonidos) y

la opción no se activará.

 Si la opción elegida no es compatible con otra

seleccionada precedentemente, el piloto

correspondiente a la primera opción seleccionada

centelleará y quedará activada sólo la segunda, el

piloto del botón permanecerá fijo.

7. PONER EN MARCHA EL PROGRAMA. Presione el

botón START/PAUSE. El piloto correspondiente

quedará fijo y la puerta se bloqueará (piloto

BLOQUEO DE LA PUERTA encendido). Los

iconos correspondientes a las fases de lavado se

iluminarán durante el ciclo para indicar la fase en

curso. Para cambiar un programa mientras un ciclo

se está ejecutando, ponga la lavadora en pausa

presionando el botón START/PAUSE; luego

seleccione el ciclo deseado y presione nuevamente el

botón START/PAUSE.

Para abrir la puerta mientras un ciclo se está

ejecutando, presione el botón START/PAUSE; si el

piloto BLOQUEO DE LA PUERTA está apagado,

será posible abrir la puerta. Presione nuevamente el

botón START/PAUSE para reanudar el programa a

partir del momento en el que se había interrumpido.

8. FIN DEL PROGRAMA. Se indica con la palabra

END encendida. La puerta se podrá abrir

inmediatamente. Si el piloto START/PAUSE centellea,

presione el botón para terminar el ciclo. Abra la

puerta, descargue la ropa y apague la máquina.

 Si desea anular un ciclo que ya ha comenzado,

mantenga presionado el botón hasta que el ciclo se

interrumpa y la máquina se apague.

Bolsa para mantas acolchadas, cortinas y

prendas delicadas

Gracias a la bolsa especial suministrada, la lavadora

Aqualtis le permite lavar también sus prendas más

valiosas y delicadas garantizándole su máxima

protección. Se recomienda utilizar siempre la bolsa

cuando lave mantas acolchadas y edredones con funda

externa de material sintético.

Cómo efectuar un ciclo de lavado

Downloaded From WashingMachine-Manual.com Manuals

Opciones de lavado

Super Wash

Gracias al uso de una mayor cantidad de agua en la

fase inicial del ciclo y a la mayor duración del programa,

esta opción garantiza un

lavado con óptimos

resultados, es útil para

eliminar las manchas más

resistentes.

Puede emplearse con o sin

lejía. Si se desea efectuar

también el blanqueado

introducir la cubeta adicional

3 en dotación, en la cubeta

1. Al dosificar el

blanqueador, no supere el

nivel max indicado en el perno central (ver la figura).

Para realizar sólo el blanqueo, sin realizar un lavado

completo, verter el blanqueador en la cubeta adicional

3, seleccionar el programa "Enjuague" y activar la

opción "Super Wash" .

 No se puede activar con los programas , , , ,

, , , .

Plancha fácil

Cuando se selecciona esta opción, el lavado y el

centrifugado se modificarán oportunamente para

disminuir la formación de arrugas. Al finalizar el ciclo, la

lavadora realizará giros lentos del cesto; los pilotos

Plancha fácil y START/PAUSE centellearán. Para

terminar el ciclo, presione el botón START/PAUSE o el

botón Plancha fácil.

En el programa Seda la máquina terminará el ciclo

dejando la ropa en remojo y el piloto Plancha fácil

centelleará. Para descargar el agua y poder sacar la

ropa, es necesario presionar el botón START/PAUSE o el

botón Plancha fácil.

 No se puede activar con los programas , , , , .

Ahorro de Tiempo

Seleccionando esta opción se disminuye la duración del

programa en un 30%-50% en base al ciclo elegido,

garantizando al mismo tiempo un ahorro de agua y

energía. Utilice este ciclo para prendas no

excesivamente sucias.

 No se puede activar con los programas , , , ,

, , , , .

Enjuague Extra

Al elegir esta opción aumentará la eficacia del aclarado y

se asegurará la máxima eliminación de los residuos de

detergente. Es útil para pieles particularmente sensibles

a los detergentes. Se aconseja el uso de esta opción

cuando la lavadora funciona a plena carga o utilizando

elevadas dosis de detergente.

 No se puede activar con los programas , , .

Programas y opciones

Tabla de programas

Para todos los Test Institutes:

1) Programa de control según la norma EN 60456: seleccione el programa

con una temperatura de 60ºC.

2) Programa algodón largo: seleccione el programa

con una temperatura de 40ºC.

3) Programa algodón corto: seleccione el programa con una temperatura de 40ºC.

Icono Descripción del Programa

Te m p .

max.

(°C)

Velocidad

máx.

(r.p.m.)

Detergentes y aditivos Carga

max.

(Kg)

Dura-

ción

del

ciclo

Lavado Suavizante Blanqueador

Programas Algodón

Algodón con prelavado

(Agregue el detergente en el compartimento correspondiente). 90° 1000 ll -7174

Algodón (1): blancos y colores resistentes muy sucios. 60°

(Max. 90°) 1000 ll l7153

Algodón (2): blancos y colores delicados muy sucios. 40° 1000 ll l7148

Algodón de color (3) 40° 1000 ll l792

Camisas 40° 600 ll l

269

Vaqueros 40° 800 ll -3,5 80

Programas especiales

Baby: colores delicados muy sucios. 40° 800 ll l

3118

Sintético resistentes 60° 800 ll l

385

Sintético delicados 40° 800 ll l

374

Ropa "7 días": lencería de cama, toallas, albornoz. 60° 1000 ll l795

Anorak: para prendas rellenas con plumas de ánsar. 30° 1000 ll -294

Seda: para prendas de seda, viscosa, lencería. 30° 0 ll -155

Lana: para lana, cachemira, etc. 40° 600 ll -1,5 55

Mix 30': para refrescar rápidamente prendas poco sucias (no se

aconseja utilizarlo para lana, seda y prendas para lavar a mano). 30° 800 ll -330

Programas parciales

Enjuague -1000 -ll

736

Centrifugado -1000 - - - 716

Desaguado -0- - - 72

Downloaded From WashingMachine-Manual.com Manuals

Detergentes y ropa

Detergente

El tipo y la cantidad de detergente dependen del tipo de

tejido (algodón, lana, seda...), del color, de la

temperatura de lavado, del grado de suciedad y de la

dureza del agua.

Dosificar bien el detergente evita derroches y protege el

medio ambiente: aún siendo biodegradables, los

detergentes contienen elementos que alteran el equilibrio

de la naturaleza.

Se aconseja:

 usar detergentes en polvo para prendas de algodón

blancas y para el prelavado.

 usar detergentes líquidos para prendas delicadas de

algodón y para todos los programas a baja

temperatura.

 usar detergentes líquidos delicados para lana y seda.

El detergente se debe verter antes del comienzo del

lavado en la cubeta correspondiente, o en el dosificador

que se coloca directamente en el cesto. En este último

caso, no se puede seleccionar el ciclo Algodón con

prelavado.

 No use detergentes para lavar a mano porque

producen demasiada espuma.

Preparar la ropa

 Abra bien las prendas antes de cargarlas.

 Divida la ropa según el tipo de tejido (símbolo en la

etiqueta de la prenda) y el color, separando las

prendas de color de las blancas;

 Vacíe los bolsillos y controle los botones;

 No supere los valores indicados en la Tabla de

Programas referidos al peso de la ropa seca.

¿Cuánto pesa la ropa?

1 sábana 400-500 gr.

1 funda 150-200 gr.

1 mantel 400-500 gr.

1 albornoz 900-1200 gr.

1 toalla 150-250 gr.

1 jeans 400-500 gr.

1 camisa 150-200 gr.

Consejos sobre el lavado

Camisas: utilice el programa correspondiente

Camisas para lavar camisas de distintos tipos de

tejido y color, garantizando su máximo cuidado.

Vaqueros: utilice el programa correspondiente

Vaqueros para todas las prendas de tejido Denim;

voltee las prendas antes del lavado y utilice un

detergente líquido.

Baby: utilice el programa correspondiente Baby para

quitar la suciedad típica de los niños y eliminar el

detergente de las prendas evitando reacciones alérgicas

en la piel delicada de los mismos. Este ciclo ha sido

estudiado para disminuir la carga bacteriana utilizando

una mayor cantidad de agua y optimizando el efecto de

aditivos específicos higienizantes agregados al detergente.

Al finalizar el lavado, la máquina realizará lentas

rotaciones del cesto; para terminar el ciclo, presione el

botón START/PAUSE.

Seda: utilice el programa correspondiente Seda

para lavar todas las prendas de seda. Se aconseja el

uso de un detergente específico para prendas delicadas.

Cortinas: utilice el programa Seda . Se recomienda

plegarlas e introducirlas en la bolsa suministrada.

Lana: Hotpoint/Ariston es la única lavadora que ha

obtenido el prestigioso reconocimiento Woolmark

Platinum Care (M.0508) otorgado por The Woolmark

Company que certifica el lavado en lavadora de todas las

prendas de lana, incluidas aquellas que contienen la

etiqueta sólo lavado a mano . Con el programa

Lana, se pueden lavar en lavadora todas las prendas de

lana con la garantía de obtener los mejores resultados.

Anorak: para lavar prendas con relleno de pluma de

ganso como edredones para camas individuales (que no

excedan los 2 kg. de peso), cojines y anoraks, utilice el

programa Anorak . Se recomienda cargar los

edredones en el cesto doblando sus bordes hacia dentro

(ver las figuras) y no superar los ¾ del volumen de dicho

cesto.

Para lograr un lavado óptimo, se recomienda utilizar

detergente líquido introduciéndolo en el contenedor de

detergente.

Mantas acolchadas: para lavar mantas acolchadas

con funda sintética, utilice la bolsa suministrada y elija el

programa Anorak .

Lencería de cama, toallas, albornoz: para lavar la

ropa de toda la casa en un único ciclo utilice el

programa 7 Días que optimiza el uso de suavizante

y permite ahorrar tiempo y energía. Se aconseja el uso

de detergente en polvo.

Manchas difíciles: es una buena costumbre tratar las

manchas difíciles con jabón sólido antes del lavado y

utilizar el programa Algodón con prelavado.

Sistema de equilibrado de la carga

Antes de cada centrifugado, para evitar vibraciones

excesivas y para distribuir la carga de modo uniforme, el

cesto realiza rotaciones a una velocidad ligeramente

superior a la del lavado. Si después de varios intentos, la

carga todavía no está correctamente equilibrada, la

máquina realiza el centrifugado a una velocidad inferior a

la prevista. Cuando existe un excesivo desequilibrio, la

lavadora realiza la distribución antes que el centrifugado.

Para obtener una mejor distribución de la carga y su

correcto equilibrado, se aconseja mezclar prendas

grandes y pequeñas.

Downloaded From WashingMachine-Manual.com Manuals

Strona jest ładowana ...

Hotpoint Ariston AQ7L 05 U Instructions For Installation And Use Manual

Marka: Hotpoint Ariston

Model: AQ7L 05 U

Kategoria: Pralki

Typ: Instructions For Installation And Use Manual

ściągnij PDF

raport

w innych językach

español: Hotpoint Ariston AQ7L 05 U
English: Hotpoint Ariston AQ7L 05 U

Hotpoint Ariston AQ7L 05 U Instructions For Installation And Use Manual

Hotpoint Ariston AQ7L 05 U Instructions For Installation And Use Manual

w innych językach

Powiązane dokumenty

Inne dokumenty