Yamaha CLP-124 Instrukcja obsługi

Marka: Yamaha

Model: CLP-124

Kategoria: Pianina cyfrowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

CLAVINOVA C L P - 3 8

CLP-124

Español

Manual de instrucciones

Páginas 62 — 81

English

Owner’s Manual Page 2 — 21

Deutsch

Bedienungsanleitung Seite 22 — 41

Français

Mode d’emploi Pages 42 — 61

Introduction

Thank you for choosing a Yamaha CLP-124 Clavinova. Your Clavinova is a fine musical instru-

ment that employs advanced Yamaha music technology. With the proper care, your Clavinova

will give you many years of musical pleasure.

● Stereo sampling of the acoustic piano voices offers unmatched realism and expressive power, while

the AWM (Advanced Wave Memory) tone generator system offers rich, realistic reproductions of all

other voices.

● 32-note polyphony permits use of the most sophisticated playing techniques.

● Piano-like touch response — adjustable in 3 stages — provides extensive expressive control and out-

standing playability.

● Dual play mode allows 2 voices to be played simultaneously.

● A number of built-in effects for wide-ranging sonic versatility.

● Unique Clavinova Tone voice provides a fresh sound for new musical expression.

● Damper pedal includes natural resonance effect for the piano voices, simulating the string and sound-

board resonance of acoustic pianos.

● MIDI compatibility and a range of MIDI functions make the Clavinova useful in a range of advanced

MIDI music systems.

In order to make the most of your Clavinova’s performance potential and features, we urge you

to read this Owner’s Manual thoroughly, and keep it in a safe place for later reference.

Your Clavinova is a fine musical instrument, and deserves the most careful treatment.

Observe the following points and your Clavinova will sound and look great for many years.

1 Never open the case and touch or tamper with the inter-

nal circuitry.

2 Always turn the POWER switch OFF after use, and

close the key cover to protect the keyboard.

3 Clean the cabinet and keys of your Clavinova only with

a clean, slightly damp cloth. A neutral cleanser may be

used if desired. Never use abrasive cleansers, waxes,

solvents or chemical dust cloths since these can dull or

damage the finish.

4 Never place any vinyl products on your Clavinova. Con-

tact with vinyl can cause irreversible damage to the

finish.

5 Install your Clavinova in a place that is away from di-

rect sunlight, excessive humidity or heat.

6 Never apply excessive force to the controls, connectors

or other parts of your Clavinova, and avoid scratching

or bumping it with hard objects.

7 Make sure that your local AC mains voltage matches the

voltage specified on the name plate.* In some areas a

voltage selector may be provided on the rear panel of

the main unit. Make sure that the voltage selector is set

for the voltage in your area.

* Name Plate Location

The CLP-124 name plate is located on the bottom panel.

Taking Care Of Your Clavinova

Contents

The Control Panel................................................................................................... 4

Connections............................................................................................................. 6

Selecting & Playing Voices .................................................................................. 7

■ Playing the Demonstration Tunes .......................................................................... 8

The Dual Mode......................................................................................................... 9

● Adjusting the Balance Between the Dual-mode Voices..................................... 9

● Shifting a Dual-mode Voice Up One Octave ..................................................... 9

● Slow-attack Strings ............................................................................................ 9

● Memorizing the Balance, Strings Type, & Octave Shift Settings ....................... 9

Reverb...................................................................................................................... 10

● Adjusting Reverb Depth ................................................................................... 10

● Memorizing the Reverb Type & Depth Settings............................................... 10

Effects...................................................................................................................... 11

● Memorizing Effects for Each Voice .................................................................. 11

The Pedals .............................................................................................................. 11

● Soft (Left) Pedal ............................................................................................... 11

● Sostenuto (Center) Pedal ................................................................................ 11

● Damper (Right) Pedal ...................................................................................... 11

Touch Sensitivity .................................................................................................. 12

● Memorizing the Touch Sensitivity Setting ........................................................ 12

Transposition......................................................................................................... 12

Pitch Control .......................................................................................................... 13

● Tuning Up ........................................................................................................ 13

● Tuning Down.................................................................................................... 13

● To Restore Standard Pitch .............................................................................. 13

Individual Key Tuning.......................................................................................... 14

● To Lower the Pitch of a Single Key.................................................................. 14

● To Raise the Pitch of a Single Key .................................................................. 14

● To Restore Standard Tuning For A Single Key ............................................... 14

● To Turn the Individual Key Tune Mode ON or OFF......................................... 15

● To Restore Standard Tuning For All Keys ....................................................... 15

Factory Preset Recall .......................................................................................... 15

MIDI Functions ...................................................................................................... 16

● A Brief Introduction to MIDI.............................................................................. 16

● MIDI “Messages” Transmitted & Received by the Clavinova .......................... 16

● MIDI Transmit & Receive Channel Selection................................................... 17

● MIDI Transmit Transpose ................................................................................ 17

■ Other MIDI Functions ............................................................................................. 18

● Local Control ON/OFF ..................................................................................... 18

● Program Change ON/OFF ............................................................................... 18

● Control Change ON/OFF ................................................................................. 19

● The Multi-Timbre Mode.................................................................................... 19

● The MIDI Split & Left Local OFF Mode ............................................................ 20

● The MIDI Split & Right Local Off Mode ............................................................ 20

● Transmitting the Panel Settings ....................................................................... 20

Troubleshooting.................................................................................................... 21

Options & Expander Modules ........................................................................... 21

Keyboard Stand Assembly ................................................................................ 82

MIDI Data Format .................................................................................................. 90

MIDI Implementation Chart ................................................................................ 92

Specifications ........................................................................................................ 93

The Control Panel

1 [POWER] Switch

Press the [POWER] switch once to turn the power

ON, a second time to turn the power OFF. When the

power is initially turned ON, the [PIANO 1] voice

selector LED will light.

2 [MASTER VOLUME] Control

The [MASTER VOLUME] control adjusts the vol-

ume (level) of sound produced by the Clavinova’s

internal stereo sound system. The [MASTER VOL-

UME] control also adjusts headphone volume when a

pair of headphones is plugged into the HEADPHONES

jack (page 6).

3 [BRILLIANCE] Button

This button can be used to change the tonality or “tim-

bre” of the selected voice. Three settings are provided:

MELLOW, NORMAL, and BRIGHT. To select one of

these settings, press the [BRILLIANCE] button a few

times until the indicator corresponding to the desired

setting lights. The NORMAL setting produces the

“normal” tone of the selected voice. The BRIGHT

setting creates a brighter or “sharper” tone, while the

MELLOW setting produces a “rounder” more mellow

tone.

4 [REVERB] Button

The [REVERB] button selects a number of digital

reverb effects that you can use for extra depth and

expressive power.

➪

See page 10 for details.

5 [EFFECT] Button

The [EFFECT] button selects a range of three effects

— detune, chorus, and tremolo — that you can use in

addition to the REVERB effects.

➪

See page 11 for details.

6 [TOUCH SENSITIVITY] Button

The [TOUCH SENSITIVITY] button selects three

different types of keyboard touch sensitivity —

HARD, MEDIUM or SOFT — to match different play-

ing styles and preferences.

➪

See page 12 for details.

A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 D1 E1 F1 G1

234567 8

MASTER VOLUME

MIN MAX

BRILLIANCE

MELLOW

NORMAL

BRIGHT

REVERB

HALL 1

HALL 2

COSMIC

ROOM

EFFECT

DETUNE

CHORUS

TREMOLO

TOUCH

SENSITIVITY

HARD

MEDIUM

SOFT

MIDI/

TRANSPOSE

PIANO

CLAVINOVA

TONE

E. PIANO

HARPSI-

CHORD

VIBES STRINGS ORGAN

A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4

Transpose keys

(See page 12)

Balance/Depth keys (See page 9, 10)

Pitch control keys

(See page 13)

Left voice shift up key

(See page 9)

HEADPHONES Jacks

(Bottom Panel)

7 [MIDI/TRANSPOSE] Button

The [MIDI/TRANSPOSE] button allows access to the

Clavinova’s TRANSPOSE function (to shift the pitch

of the entire keyboard up or down) and MIDI func-

tions. For details refer to the “TRANSPOSITION” and

“MIDI FUNCTIONS” sections on pages 12 and 16,

respectively.

8 Voice Selectors

The CLP-124 has ten voice selectors. Simply press any

of the voice selectors to select the corresponding

voice. The LED indicator above the voice selector will

light to indicate which voice is currently selected.

The CLP-124 also has a DUAL mode in which two

voices can be played simultaneously across the full

range of the keyboard — see page 9 for details.

Note: The PIANO 1 voice is automatically selected when-

ever the [POWER] switch is initially turned ON.

9 Pedals

The CLP-124’s soft (left), sostenuto (center), and

damper (right) pedals provide a range of expressive

control capabilities similar to the pedal functions on an

acoustic piano.

➪

See page 11 for details.

● The Music Stand

If you will be using sheet music with your

Clavinova, raise the music stand built into its top

panel by lifting the rear edge of the music stand,

then flip down the music stand braces and engage

them with the corresponding recesses.

The music stand can be lowered after slightly

lifting it and folding the two brackets which support

it against the back of the stand.

C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7

Demonstration key (See page 8)

Memory key (See page 9, 10, 11, 12, 13)

Soft pedal

Sostenuto pedal

Damper pedal

Right voice shift up key

(See page 9)

MIDI

IN OUT THRU

DRC-20

Connections

312

These jacks are intended for use with an external tone generator module

such as the Yamaha DOM-30 Disk Orchestra Module. The stereo outputs

from the external tone generator module are connected to the OPTIONAL

IN L and R jacks, allowing the sound of the tone generator to be reproduced

via the Clavinova’s internal sound system and speakers.

The AUX OUT R and L/L+R jacks deliver the output of the Clavinova

for connection to an instrument amplifier, mixing console, PA system, or

recording equipment. If you will be connecting the Clavinova to a monaural

sound system, use only the L/L+R jack. When a plug is inserted into the L/

L+R jack only, the left- and right-channel signals are combined and deliv-

ered via the L/L+R jack so you don’t lose any of the Clavinova’s sound.

The Internal Amplifier & Speaker System

The CLP-124 features a powerful stereo amplifier delivering 50 watts per channel,

driving a speaker system that puts out exceptionally rich sound with natural re-

sponse from powerful lows to shimmering highs. The speaker system includes

two 16-centimeter speaker units, two 10-centimeter units, and two 5-centimeters

speaker units.

Note: The AUX OUT jack signal must never be returned to the OPTIONAL IN jacks,

either directly or through external equipment.

The MIDI IN connector receives MIDI data from an external MIDI de-

vice (such as the DRC-20 Disk Recorder, or DOM-30 Disk Orchestra Mod-

ule) which can be used to control the Clavinova. The MIDI THRU connec-

tor re-transmits any data received at the MIDI IN connector, allowing

“chaining” of several MIDI instruments or other devices. The MIDI OUT

connector transmits MIDI data generated by the Clavinova (e.g. note and

velocity data produced by playing the Clavinova keyboard).

More details on MIDI are given in “MIDI FUNCTIONS” on page 16.

1 OPTIONAL IN L/R Jacks

OPTIONAL IN

DOM-30

AUX. OUT

L/L+RR

2 AUX OUT R and L/L+R Jacks

Stereo System

3 MIDI IN, THRU and OUT

Connectors

Two pairs of standard pair of stereo headphones can be plugged in here

for private practice or late-night playing. The internal speaker system is

automatically shut off when a pair of headphones is plugged into either of

the HEADPHONES jacks.

● HEADPHONES Jacks (Bottom Panel)

Tone Generator

ZTurn Power On

After making sure that the Clavinova’s AC plug is properly inserted into

a convenient AC wall outlet, press the [POWER] switch located to the left

of the keyboard to turn the power ON.

When the power is turned ON, the [PIANO 1] voice selector LED will

light (the PIANO 1 voice is automatically selected whenever the power is

turned ON).

Initially set the [MASTER VOLUME] control about half way between

the “MIN” and “MAX” settings. Then, when you start playing, re-adjust the

[MASTER VOLUME] control for the most comfortable listening level.

Select the desired voice by pressing one of the voice selectors.

All CLP-124 voices have 32-note polyphony, which means you can play

up to 32 notes at once. The Clavinova also offers keyboard touch response,

so the volume and timbre of notes played can be controlled according to

how “hard” you play the keys. The amount of variation available depends

on the selected voice.

* The total number of notes that can be played simultaneously is reduced from 32

to 16 when the DUAL play mode is used. See page 9 for information on the

DUAL play mode.

You can also change the overall tone or add reverb and/or effects as de-

sired by using the [BRILLIANCE], [REVERB] and [EFFECT] buttons

(see page 4 for [BRILLIANCE] button operation, “Reverb” on page 10,

and “Effects” on page 11).

XSet the Volume

POWER

MASTER VOLUME

MIN MAX

CSelect a Voice

PIANO

CLAVINOVA

TONE

E. PIANO

HARPSI-

CHORD

VIBES STRINGS ORGAN

VPlay

BAdjust Tone & Add Effects

As Required

BRILLIANCE

MELLOW

NORMAL

BRIGHT

REVERB

HALL 1

HALL 2

COSMIC

ROOM

EFFECT

DETUNE

CHORUS

TREMOLO

Selecting & Playing Voices

Playing the Demonstration Tunes

The CLP-124 features 10 demonstration tunes that effectively demonstrate it’s sound

capabilities. Here’s how you can select and play the demo tunes.

Press the C7 key while holding the [MIDI/TRANSPOSE] button. The

voice selectors will begin flashing in sequence to indicate that the demo

mode is engaged.

The 10 demo tunes are selected via the voice selectors. Press a selector to

start playback of the corresponding tune, featuring the voice normally se-

lected by that voice selector button. The demo tunes will play in sequence

until stopped, starting with the selected tune. The voice selector indicator

will flash during demo playback.

Use the [MASTER VOLUME] control to adjust the volume, and play

along on the keyboard if you like.

Press the [MIDI/TRANSPOSE] button when you want to stop demo

playback and return to the normal play mode.

The Demo Tunes

[PIANO 1] ........................... “Grande valse brillante” by F. F. Chopin

[PIANO 2] ........................... “Lake Louise” by Yuhki Kuramoto

[CLAVINOVA TONE].......... “Rêverie” by Debussy

[HARPSICHORD]............... “Invention 3” by J. S. Bach

[ORGAN] ............................ “Symphonie pour orgue No.5” by Widor

• The demonstration pieces listed above are short excerpts from the origi-

YAMAHA CORPORATION).

ZEngage the Demo Mode

XSelect a Demo Tune

Selecting & Playing Voices

MIDI/

TRANSPOSE

PIANO

CLAVINOVA

TONE

E. PIANO

HARPSI-

CHORD

VIBES STRINGS ORGAN

MASTER VOLUME

MIN MAX

CSet the Volume

VStop the Demo

MIDI/

TRANSPOSE

The Dual Mode

● Adjusting the Balance Be-

tween the Dual-mode Voices

The volume levels of the two voices combined in the DUAL mode are

normally set automatically to produce a pleasing balance (see “Default Set-

tings” below). The balance can be adjusted manually by using the C2

through C4 keys on the keyboard while pressing the two voice selectors cor-

responding to the voices to be combined in the DUAL mode.

The C3 key produces equal (50:50) balance between the two voices, while

keys to the left of C3 increase the volume of the left voice in relation to the

right voice, and keys to the right of C3 increase the volume of the right voice

in relation to the left voice. By “left” and “right” voice we refer to the rela-

tive positions of the voice selectors — i.e. in a STRINGS/ORGAN combina-

tion STRINGS is the left voice and ORGAN is the right voice.

Depending on which voices you combine using the DUAL mode, the com-

bination may sound better if one of the voices is shifted up an octave. To

shift the right voice, press the C5 key while pressing the two voice selectors

corresponding to the voices to be combined in the DUAL mode. Press C5

again to shift the voice back to its normal range. Use the C1 key in the same

way to shift the left voice.

Default octave settings are provided for all voice combinations, as listed in

the “Default Settings” chart, below.

In a DUAL mode voice combination using STRINGS and any other voice,

it is possible to switch the STRINGS voice to a slow-attack variation when

initially selecting the voices by pressing the [STRINGS] selector twice while

holding the other voice selector.

Press the C7 key while holding any two voice selectors to memorize all

balance, STRINGS voice attack variation, and octave shift settings made

since the power was turned on. The memorized settings will be retained in

memory for about one week after the power is turned off, then the default

settings will be restored. To keep the memorized settings for longer periods,

turn the power on briefly at least once a week.

If these settings are not memorized as described above, they are retained in

memory only until the Clavinova is turned off.

The DUAL mode makes it possible to play two voices simultaneously across the entire range of the key-

board. To activate the DUAL mode simply press two voice selectors at the same time (or press one voice

selector while holding another). The voice indicators of both selected voices will light when the DUAL mode

is active. To return to the normal single-voice play mode, press any single voice selector.

IBES STRINGS ORGAN

Equal

balance.

Left voice

maximum.

Right voice

maximum.

● Shifting a Dual-mode Voice

Up One Octave

IBES STRINGS ORGAN

Left voice

shift up.

Right voice

shift up.

● Slow-attack Strings

IBES STRINGS ORGAN

PIANO

PIAN

● Memorizing the Balance,

Strings Type, & Octave Shift

Settings

IBES STRINGS ORGAN

PIANO 1 PIANO 2 PIANO 3

CLAVINOVA

E. PIANO 1 E. PIANO 2

HARPSI-

VIBES STRINGS ORGAN

TONE

CHORD

PIANO 1 C3 C3 C3 C3 C3 C3 C3 F2 E2

PIANO 2 0 C3 C3 C3 C3 C3 C3 F2 E2

PIANO 3 0 0 C3 C3 C3 C3 C3 F2 E2

CLAVINOVA TONE

0 0 0 C3C3C3C3F2F2

E. PIANO 1 0 0 0 0

C3 C3 C3 F2 E2

E. PIANO 2 0 0 0 0 0

A2 C3 F2 F2

HARPSICHORD 0 0 0 0 0 0 C3 F2 G2

VIBES R R R RRRR B2B2

STRINGS 0 0 0 0 000L C3

ORGAN 0 0 0 0 000L0

Balance

Default Settings

Octave Shift

C2 … C4: Balance keys 0: Normal octave L: Left voice up one octave R: Right voice up one octave

ROOM........This setting add a continuous reverb effect to the sound that is similar to the type of

acoustic reverberation you would hear in a medium-size room.

HALL 1 ......For a “bigger” reverb sound, use the HALL 1 setting. This effect simulates the natu-

ral reverberation of a medium-size concert hall.

HALL 2 ......For a really spacious reverb sound, use the HALL 2 setting. This effect simulates the

natural reverberation of a large concert hall.

COSMIC ....The COSMIC reverb effect produces an echo-plus-reverb sound that can add life and

animation to your music.

The depth of the selected reverb effect can be adjusted for the current

voice by using the C2 through C4 keys on the keyboard while holding the

[REVERB] button. The C3 key sets the “normal” depth for the selected

effect. Keys to the left of C3 decrease the reverb depth, while keys to the

right of the C3 key increase the reverb depth. Separate reverb settings can

be made for each effect and voice.

The default reverb depth settings are given in the “Default Settings”

chart, below

Press the C7 key while holding the [REVERB] button to memorize the

current effect type and all depth settings made since the power was turned

on. The memorized settings will be retained in memory for about one week

after the power is turned off, then the default settings will be restored. To

keep the memorized settings for longer periods, turn the power on briefly at

least once a week.

If these settings are not memorized as described above, they are retained

in memory only until the Clavinova is turned off.

Reverb

The [REVERB] button selects a number of digital reverb effects that you can use for

extra depth and expressive power.

To select a reverb type press the [REVERB] button a few times until the indicator

corresponding to the desired type lights (the indicators light in sequence each time the

[REVERB] button is pressed). No reverb is produced when all indicators are off.

REVERB

HALL 1

HALL 2

COSMIC

ROOM

Normal

depth.

Decrease

depth.

Increase

depth.

● Adjusting Reverb Depth

ROOM HALL 1 HALL 2

COSMIC

STRINGS, ORGAN C3 C3 F3 E3

Default Settings

REVERB

HALL 1

HALL 2

COSMIC

ROOM

● Memorizing the Reverb

Type & Depth Settings

* All effect types set to C3 for all other voices.

* The default reverb type is OFF.

DETUNE ......DETUNE delivers a thick, multi-instrument sound by producing two notes of

slightly different pitch for every single note you play on the keyboard — i.e.

the two notes are slightly “detuned.”

CHORUS .....This produces an animated “shimmering” effect that both thickens the sound

and gives it a more lively feel.

TREMOLO...TREMOLO is a gentle variation in volume that gives the sound a more dy-

namic feel. The tremolo speed is independently preset for each voice.

The CLP-124 allows different effects to be set for each voice so that the

appropriate effect is automatically recalled whenever a voice is selected.

The initial effect assignments when the CLP-124 power is turned on are

given in the chart below.

These settings can be changed by selecting the desired voice and effects,

and then pressing the C7 key while holding the [EFFECT] button. All set-

tings made since the power was turned on are memorized. The memorized

settings will be retained in memory for about one week after the power is

turned off, then the default settings will be restored. To keep the memorized

settings for longer periods, turn the power on briefly at least once a week.

If these settings are not memorized as described above, they are retained

in memory only until the Clavinova is turned off.

● Memorizing Effects for Each

Voice

The [EFFECT] button selects a range of three effects that you can use in addition to the

REVERB effects.

To select an effect press the [EFFECT] button a few times until the indicator correspond-

ing to the desired effect lights (the indicators light in sequence each time the [EFFECT]

button is pressed). No effect is produced when all indicators are off.

Effects

Pressing the soft pedal reduces the volume and slightly changes the timbre of notes played.

The soft pedal actually functions in eight levels, depending on how hard it is pressed.

If you play a note or chord on the keyboard and press the sostenuto pedal while the note(s)

are held, those notes will be sustained as long as the pedal is held (as if the damper pedal had

been pressed) but all subsequently played notes will not be sustained. This makes it possible

to sustain a chord, for example, while other notes are played “staccato.”

The damper pedal functions in the same way as a damper pedal on an acoustic piano. When

the damper pedal is pressed notes played have a long sustain. When a piano voice is selected

the damper pedal also produces a special “resonance” that simulates the ring of the strings and

the sound board of an acoustic piano. Releasing the pedal immediately stops (damps) any sus-

tained notes. The CLP-124 damper pedal additionally features continuous damping. This al-

lows you to create shorter effects by pressing the damper pedal down only part of the way.

● Sostenuto (Center)

Pedal

The CLP-124 has three foot pedals that produce a range of expressive effects similar to

those produced by the pedals on an acoustic piano.

The Pedals

● Soft (Left) Pedal

● Damper (Right)

Pedal

EFFECT

DETUNE

CHORUS

TREMOLO

Voice

PIANO 1 PIANO 2 PIANO 3

CLAVINOVA

E. PIANO 1 E. PIANO 2

HARPSI-

VIBES STRINGS ORGAN

TONE

CHORD

Power-on

OFF OFF OFF OFF OFF CHORUS OFF TREMOLO OFF OFF

Effect

HARD.........The HARD setting requires the keys to be played quite hard to produce maximum loudness.

MEDIUM ....The MEDIUM setting produces a fairly “standard” keyboard response. This is the initial factory

default setting.

SOFT .........The SOFT setting allows maximum loudness to be produced with relatively light key pressure.

● Memorizing the Touch Sen-

sitivity Setting

Press the C7 key while holding the [TOUCH SENSITIVITY] button to

memorize the current touch sensitivity setting. The memorized setting will

be retained in memory for about one week after the power is turned off,

then the default setting will be restored. To keep the memorized setting for

longer periods, turn the power on briefly at least once a week.

If this settings is not memorized as described above, it is retained in

memory only until the Clavinova is turned off.

The [MIDI/TRANSPOSE] button and keys F#2 through F#3 on the keyboard are used for transposition.

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress a key between F#2 and F#3 according to the desired amount of

transposition.*

CRelease the [MIDI/TRANSPOSE] button.

* Pressing the C3 key produces normal keyboard pitch. Pressing the key to

the left of C3 (B2) transposes the pitch of the keyboard down a semitone,

the next key to the left (Bb2) transposes down a whole tone (two semi-

tones), etc., down to the F#2 key which transposes down 6 semitones.

Upward transposition is accomplished in the same way using the keys to

the right of C3, up to F#3 which transposes up 6 semitones.

The [TOUCH SENSITIVITY] button selects three different types of keyboard touch sensi-

tivity — HARD, MEDIUM or SOFT — to match different playing styles and preferences.

To select a touch sensitivity setting press the [TOUCH SENSITIVITY] button a few times

until the indicator corresponding to the desired setting lights (the indicators light in se-

quence each time the [TOUCH SENSITIVITY] button is pressed).

Touch Sensitivity

The Clavinova’s TRANSPOSE function makes it possible to shift the pitch of the entire key-

board up or down in semitone intervals up to a maximum of six semitones. “Transposing” the

pitch of the Clavinova keyboard facilitates playing in difficult key signatures, and you can easily

match the pitch of the keyboard to the range of a singer or other instrumentalist.

Transposition

TOUCH

SENSITIVITY

HARD

MEDIUM

SOFT

Normal

pitch.

Transpose

down.

Transpose

up.

MIDI/

TRANSPOSE

● Tuning Up

ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is increased by approximately 1.2 cents, up to a maxi-

mum of 50 cents above standard pitch.

CRelease the A-1 and B-1 keys.

ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simultane-

ously.

XPress any key between C3 and B3. Each time a key in this range is

pressed the pitch is decreased by approximately 1.2 cents, up to a maxi-

mum of 50 cents below standard pitch.

CRelease the A-1 and A#-1 keys.

ZTo restore standard pitch (A3 = 440 Hz), hold the A-1, A#-1 and B-1

keys simultaneously.

XPress any key between C3 and B3.

CRelease the A-1, A#-1 and B-1 keys.

* Standard pitch (A3 = 440 Hz) is set when the [POWER] switch is ini-

tially turned ON. The power-on pitch setting can be changed, however,

by pressing the C7 key while still holding the A-1/B-1, A-1/A#-1, or A-

1/A#-1/B-1 key combinations after setting the desired pitch.

Settings changed in this way are retained in internal memory for approxi-

mately one week if the power is not turned on during that time. If the

backup period is exceeded, the original factory setting is restored. To

keep the memorized settings for longer periods, turn the power on briefly

at least once a week.

Note: The PITCH CONTROL function has no effect when LOCAL OFF is active

(see “MIDI FUNCTIONS,” page 18).

● Tuning Down

● To Restore Standard Pitch*

Pitch control makes it possible to tune the Clavinova over a ±50-cent range in approximately

1.2-cent intervals. A hundred “cents” equals one semitone, so the tuning range provided allows

fine tuning of overall pitch over a range of approximately a semitone. Pitch control is useful for

tuning the Clavinova to match other instruments or recorded music.

Pitch Control

-1

MIDI/

TRANSPOSE

RPSI-

ORD

VIBES STRINGS ORG

MIDI/

TRANSPOSE

RPSI-

ORD

VIBES STRINGS ORG

MIDI/

TRANSPOSE

RPSI-

ORD

VIBES STRINGS ORG

● To Lower the Pitch of a Single

Key

ZHold the [MIDI/TRANSPOSE] button.

XPress and release the [VIBES] voice selector (do not release the

[MIDI/TRANSPOSE] button). The [VIBES] indicator will flash.

CWhile still holding the [MIDI/TRANSPOSE] button, press the desired

key as many times as necessary to lower its pitch by the required

amount (each press lowers pitch by approximately 1.2 cents). The [OR-

GAN] indicator will light to indicate that the Individual Key Tune

mode is ON.

VRelease the [MIDI/TRANSPOSE] button.

ZHold the [MIDI/TRANSPOSE] button.

XPress and release the [STRINGS] voice selector (do not release the

[MIDI/TRANSPOSE] button). The [STRINGS] indicator will flash.

CWhile still holding the [MIDI/TRANSPOSE] button, press the desired

key as many times as necessary to raise its pitch by the required amount

(each press raises pitch by approximately 1.2 cents). The [ORGAN]

indicator will light to indicate that the Individual Key Tune mode is

ON.

VRelease the [MIDI/TRANSPOSE] button.

ZHold the [MIDI/TRANSPOSE] button.

XPress and release the [VIBES] and [STRINGS] voice selectors simulta-

neously (do not release the [MIDI/TRANSPOSE] button). The

[VIBES] and [STRINGS] indicators will flash.

CWhile still holding the [MIDI/TRANSPOSE] button, press the key you

want to restore to normal pitch.

VRelease the [MIDI/TRANSPOSE] button.

● To Raise the Pitch of a Single

Key

● To Restore Standard Tuning

For A Single Key

When used in ensemble with other keyboards and particularly acoustic pianos, however, slight

tuning discrepancies can arise. The CLP-124 is equipped with an individual key tuning features that

allows such differences to be accurately compensated for. The individual key tuning feature also

makes it possible to tune the CLP-124 to completely different standards, if required. The pitch of

each key can be raised or lowered by a maximum of 50 cents from the standard pitch.

Individual Key Tuning

RPSI-

ORD

VIBES STRINGS ORGAN

MIDI/

TRANSPOSE

● To Turn the Individual Key

Tune Mode ON or OFF

The individual key tuning settings described above can be turned on or

off (normal tuning) while retaining the settings in memory. Individual key

tuning is always turned off when the power is initially turned on, but any

previous settings are retained in memory and can be recalled if the power

has not been off for longer than about a week. To keep the memorized set-

tings for longer periods, turn the power on briefly at least once a week.

ZHold the [MIDI/TRANSPOSE] button.

XPress the [ORGAN] voice selector to turn the Individual Key Tune

mode ON ([ORGAN] indicator on) or OFF ([ORGAN] indicator off).

CRelease the [MIDI/TRANSPOSE] button.

Note: The INDIVIDUAL KEY TUNING function has no effect when LOCAL OFF is

active (see “MIDI FUNCTIONS,” page 18).

ZHold the [MIDI/TRANSPOSE] button.

XPress and release the [VIBES], [STRINGS], and [ORGAN] voice

selectors simultaneously. The [VIBES], [STRINGS], and [ORGAN]

indicators will light.

CRelease the [MIDI/TRANSPOSE] button.

MIDI/

TRANSPOSE

RPSI-

ORD

VIBES STRINGS ORGAN

● To Restore Standard Tuning

For All Keys

All dual mode, reverb, effect, touch sensitivity, pitch control, and

individyal key tune settings can be restored to their original factory preset

(default) values by holding the C7 key while turning the [POWER] switch

ON.

Factory Preset Recall

POWER

DRC-20

Data Being Recorded

Playback Data

MIDI IN MIDI INMIDI OUTMIDI OUT

DOM-30

MIDI Cable

MIDI INMIDI OUT

● A Brief Introduction to MIDI

MIDI, the Musical Instrument Digital Interface, is a world-standard com-

munication interface that allows MIDI-compatible musical instruments and

equipment to share musical information and control one another. This

makes it possible to create “systems” of MIDI instruments and equipment

that offer far greater versatility and control than is available with isolated

instruments. For example, most MIDI keyboards (including the Clavinova,

of course) transmit note and velocity (touch response) information via the

MIDI OUT connector whenever a note is played on the keyboard. If the

MIDI OUT connector is connected to the MIDI IN connector of a second

keyboard (synthesizer, etc.) or a tone generator (essentially a synthesizer

with no keyboard), the second keyboard or tone generator will respond

precisely to notes played on the original transmitting keyboard. The result is

that you can effectively play two instruments at once, providing thick multi-

instrument sounds.

This same type of musical information transfer is used for MIDI se-

quence recording. A sequence recorder such as the Yamaha DRC-20 Disk

Recorder can be used to “record” MIDI data received from a Clavinova, for

example. When the recorded data is played back, the Clavinova automati-

cally “plays” the recorded performance in precise detail.

The examples given above really only scratch the surface. MIDI can do

much, much more. The CLP-124 offers a number of MIDI functions that

allows it to be used in fairly sophisticated MIDI systems.

Note: Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN termi-

nals. Never use MIDI cables longer than about 15 feet, since cables longer than

this can pick up noise which can cause data errors.

● MIDI “Messages” Transmitted

& Received by the Clavinova

Note and Velocity Data

This information tells the receiving keyboard or tone generator to play a certain note (specified by the MIDI

note number) at a certain dynamic level (specified by the MIDI velocity value). Note and velocity data is trans-

mitted by the Clavinova whenever a key is pressed, and the Clavinova’s internal AWM tone generator will

“play” the corresponding note(s) whenever note and velocity data is received from an external MIDI device.

Program Change Numbers

The CLP-124 transmits a MIDI program change number between 0 and 10 when one of its voice selectors is

pressed. This normally causes the correspondingly numbered voice to be selected on a receiving MIDI device.

The Clavinova will respond in the same way, automatically selecting the appropriate voice when a MIDI pro-

gram change number is received. See “Program Change ON/OFF” on page 18 for information on turning pro-

gram change number reception and transmission ON or OFF.

Control Change Numbers

Control Change data representing Soft, Sostenuto and Damper pedal operations is transmitted by the

Clavinova whenever one of these pedals is used. If the receiving device is a tone generator or another keyboard,

it will respond in the same way as the Clavinova’s internal tone generator when one of the pedals is used. The

Clavinova also receives and responds to the appropriate control change data. See “Control Change ON/OFF” on

page 19 for information on turning control change number reception and transmission ON or OFF.

The MIDI information (messages) transmitted and received by the CLP-

124 Clavinova are as follows:

Clavinova

MIDI Functions

DRC-20

Tone Generator

MIDI IN

MIDI OUT

MIDI THRU

1356810121315

2 4 7 9 11 14 16

1356810121315

2 4 7 9 11 14 16

MIDI/

TRANSPOSE

● MIDI Transmit & Receive

Channel Selection

The MIDI system allows transmission and reception of MIDI data on 16

different channels. Multiple channels have been implemented to allow se-

lective control of certain instruments or devices connected in series. For

example, a single MIDI sequence recorder could be used to “play” two

different instruments or tone generators. One of the instruments or tone

generators could be set to receive only on channel 1, while the other is set

to receive on channel 2. In this situation the first instrument or tone genera-

tor will respond only to channel-1 information transmitted by the sequence

recorder, while the second instrument or tone generator will respond only to

channel-2 information. This allows the sequence recorder to “play” two

completely different parts on the receiving instruments or tone generators.

In any MIDI control setup, the MIDI channels of the transmitting and

receiving equipment must be matched for proper data transfer. An “OMNI”

receive mode is also available, which allows reception on all 16 MIDI chan-

nels. In the OMNI mode it is not necessary to match the receive channel of

the receiving device to the transmit channel of the transmitting device (ex-

cept when receiving mode messages).

Setting the Clavinova MIDI Channels

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired MIDI trans-

mit or receive channel.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys C1 through D#2 on the keyboard are used to set the MIDI transmit

channel, and keys C4 through D#5 are used to turn the OMNI mode OFF

and set the MIDI receive channel as shown in the illustration to the left.

The E5 key sets the OMNI receive mode and basic receive channel 1.

Note: When the power is initially turned ON, MIDI receive is set to the OMNI mode

and the transmit channel is set to 1.

This function allows the MIDI note data transmitted by the Clavinova to

be transposed up or down in semitone increments by up to plus or minus 6

semitones. The pitch of the Clavinova itself is not affected.

Setting the MIDI Transpose Function

ZPress and hold the [MIDI/TRANSPOSE] button.

XPress the key on the keyboard corresponding to the desired amount of

transposition.*

CRelease the [MIDI/TRANSPOSE] button.

* Keys F#5 through F#6 on the keyboard are used to set the MIDI transmit

transpose function as shown in the illustration to the left.

Note: When the power is turned ON, MIDI transmit transpose is set to 0 (no trans-

position).

● MIDI Transmit Transpose

(Set to receive on MIDI

channel 2)

Clavinova

(Set to receive on MIDI channel 1)

For setting the transmit

channel. (C1 ~ D#2)

For setting the receive

channel. (C4 ~ D#5)

For OMNI mode

MIDI/

TRANSPOSE

-6 -4 -2 1 3 6

5420-1-3-5

MIDI Functions

MIDI FUNCTION CHART

Function CLP-124 Voice Selector

Local Control ON/OFF [PIANO 1]

Program Change ON/OFF [PIANO 2]

Control Change ON/OFF [PIANO 3]

Multi-Timbre Mode [CLAVINOVA TONE ]

MIDI Split & Left Local OFF [E.PIANO 1]

MIDI Split & Right Local OFF [E.PIANO 2]

Panel Data Transmit [HARPSICHORD]

Other MIDI Functions

The MIDI functions listed to the right are engaged by

holding down the [MIDI/TRANSPOSE] button and press-

ing the corresponding voice selector. Full details are given

in the following pages.

“Local Control” refers to the fact that, normally, the Clavinova keyboard controls its internal tone generator,

allowing the internal voices to be played directly from the keyboard. This situation is “Local Control ON” since

the internal tone generator is controlled locally by its own keyboard.

Local control can be turned OFF, however, so that the Clavinova keyboard does not play the internal voices,

but the appropriate MIDI information is still transmitted via the MIDI OUT connector when notes are played on

the keyboard. At the same time, the internal tone generator responds to MIDI information received via the MIDI

IN connector.

When using the DOM-30 Disk Orchestra Module with the Clavinova, for example, Local Control should be

turned OFF when recording using the DOM-30 voices only, and ON when recording the Clavinova voices while

listening to playback of the DOM-30 voices.

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [PIANO 1] voice selector. If the PIANO 1 LED is lit when

the [PIANO 1] voice selector is pressed, you have turned local control

OFF. If the PIANO 1 LED is not lit when the [PIANO 1] voice selector

is pressed, you have turned local control ON.

CRelease the [MIDI/TRANSPOSE] button.

Normally the Clavinova will respond to MIDI program change numbers received from an external keyboard

or other MIDI device, causing the correspondingly numbered Clavinova voice to be selected. The Clavinova

will normally also send a MIDI program change number whenever one of its voices is selected, causing the

correspondingly numbered voice or program to be selected on the external MIDI device if the device is set up to

receive and respond to MIDI program change numbers.

This function makes it possible to cancel program change number reception and transmission so that voices

can be selected on the Clavinova without affecting the external MIDI device, and vice versa.

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [PIANO 2] voice selector. If the PIANO 2 LED is lit when

the [PIANO 2] voice selector is pressed, you have turned program

change reception/transmission OFF. If the PIANO 2 LED is not lit

when the [PIANO 2] voice selector is pressed, you have turned pro-

gram change reception/transmission ON.

CRelease the [MIDI/TRANSPOSE] button.

● Local Control ON/OFF

● Program Change ON/OFF

MIDI/

TRANSPOSE

PIANO

PIAN

PIANO

= Local Control OFF

= Local Control ON

MIDI/

TRANSPOSE

PIANO

PIAN

PIANO

= Program Change OFF

= Program Change ON

DRC-20

MIDI IN MIDI INMIDI OUTMIDI OUT

Normally the Clavinova will respond to MIDI control change data received from an external MIDI device or

keyboard, causing the selected Clavinova voice to be affected by pedal and other “control” settings received

from the controlling device. The Clavinova also transmits MIDI control change information when one of its

pedals are operated.

This function makes it possible to cancel control change data reception and transmission if you do not want

the Clavinova voices to be affected by control change data received from an external device or vice versa.

● Control Change ON/OFF

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [PIANO 3] voice selector. If the PIANO 3 LED is lit when

the [PIANO 3] voice selector is pressed, you have turned control

change reception/transmission OFF. If the PIANO 3 LED is not lit

when the [PIANO 3] voice selector is pressed, you have turned control

change reception/transmission ON.

CRelease the [MIDI/TRANSPOSE] button.

The Multi-Timbre mode is a special mode in which the Clavinova voices

can be independently controlled on different MIDI channel numbers (1

through 10) by an external MIDI device such as the Yamaha DRC-20 Disk

Recorder. The Multi-Timbre mode can be activated as follows:

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [CLAVINOVA TONE] voice selector. If the CLAVINOVA

TONE LED is lit when the [CLAVINOVA TONE] voice selector is

pressed, you have turned the Multi-Timbre mode ON. If the

CLAVINOVA TONE LED is not lit when the [CLAVINOVA TONE]

voice selector is pressed, you have turned the Multi-Timbre mode OFF.

CRelease the [MIDI/TRANSPOSE] button.

A Multi-timbre Example

Here’s an example of how you could use the Multi-Timbre mode to

record two different parts on the DRC-20 Disk Recorder that will play dif-

ferent voices on the Clavinova when played back.

ZConnect the DRC-20 to the Clavinova as shown to the left.

XActivate the Clavinova Multi-Timbre mode.

CSet the DRC-20 track 1 to record.

VSelect a voice and record the first part on the DRC-20.

BSet the DRC-20 track 2 to record.

NSelect a voice and record the second part on the DRC-20.

MStill in the Multi-Timbre mode, play back the DRC-20. The recorded

parts will be played back using the individual voices selected during

recording, providing a full ensemble sound.

● The Multi-Timbre Mode

Clavinova

PIANO

CLAVI

TON

MIDI/

TRANSPOSE

PIANO

= Control Change OFF

= Control Change ON

ANO

PIANO

CLAVINOVA

TONE

E. PIA

MIDI/

TRANSPOSE

CLAVINOVA

TONE

CLAVINOVA

TONE

= Multi-Timble Mode ON

= Multi-Timble Mode OFF

DOM-30

LINE OUT

OPTIONAL IN

RMIDI OUT

MIDI

MIDI Functions

In the MIDI split mode one section of the Clavinova keyboard is used to play a Clavinova voice in the normal

way, while the remaining section is used to play a second MIDI keyboard or tone generator such as the Yamaha

DOM-30 Disk Orchestra Module. In this mode the right-hand section of the keyboard is used to play an internal

Clavinova voice, while the left-hand section of the keyboard plays the external keyboard or tone generator.

Playing the left-hand section of the keyboard produces no sound from the Clavinova. The “split point,” or the

key that divides the left- and right-hand sections of the keyboard can be set at any desired key.

● The MIDI Split & Left Local OFF Mode

The MIDI split mode is useful if, for example, you want to play a piano

(Clavinova) voice with the right hand while playing a synthesizer bass line

or string section with the left hand.

When the MIDI split mode is activated, notes played on the left-hand

section are transmitted via the Clavinova MIDI OUT connector on MIDI

channel 2. Notes played on the right-hand section are transmitted on the

“basic channel” (i.e. the channel set using the MIDI channel selection func-

tion described previously).

ZPress the [E.PIANO 1] voice selector while holding down the [MIDI/

TRANSPOSE] button. The E.PIANO 1 LED will flash.

XWhile still holding the [MIDI/TRANSPOSE] button, press the key on

the keyboard at which you want to set the split point. The E.PIANO 1

LED will light continuously. The split-point becomes the first key of

the left-hand section.

CRelease the [MIDI/TRANSPOSE] button.

VTo return to the normal full-keyboard mode, hold the [MIDI/TRANS-

POSE] button and press the [E.PIANO 1] voice selector, then release

both buttons.

Note: When the power is turned ON the default split point key — F

2 — will be

automatically selected. If a new split point is selected it remains active until the

power is turned OFF or a different split point is selected.

● The MIDI Split & Right Local Off Mode

In the CLP-124 either the right- or left-hand section of the keyboard can be assigned to control an external

keyboard or tone generator. Assigning the left-hand section to external tone generator control was described in

the previous section. To assign the right-hand section to external tone generator control while playing the

Clavinova voices with the left hand, press the [E.PIANO 2] voice selector instead of the [E.PIANO 1] voice

selector when activating the Split mode (see the preceding section). All other operations are exactly the same as

described in the previous section.

● Transmitting the Panel Settings

This function causes all the current Clavinova control settings (selected voice, etc) to be transmitted via the

MIDI OUT terminal. This is particularly useful if you will be recording performances to a MIDI sequence re-

corder which will be used to control the Clavinova on playback. By transmitting the Clavinova panel settings

and recording them on the MIDI sequence recorder prior to the actual performance data, the Clavinova will be

automatically restored to the same settings when the performance is played back.

ZHold down the [MIDI/TRANSPOSE] button.

XPress the [HARPSICHORD] voice selector.

CRelease the [MIDI/TRANSPOSE] button.

IANO

E. PIANO

HARPSI-

CHORD

VIB

MIDI/

TRANSPOSE

Clavinova

(Set to receive on

MIDI channel 2)

CLAVINOVA

TONE

E. PIANO

E. PIA

MIDI/

TRANSPOSE

▼

Left-hand section plays

a DOM-30 bass voice.

Right-hand section plays a

Clavinova piano voice.

SPLIT POINT

Strona jest ładowana ...

Yamaha CLP-124 Instrukcja obsługi

Marka: Yamaha

Model: CLP-124

Kategoria: Pianina cyfrowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

CLAVINOVA C L P - 3 8

ściągnij PDF

raport

w innych językach

čeština: Yamaha CLP-124 Uživatelský manuál
español: Yamaha CLP-124 Manual de usuario
italiano: Yamaha CLP-124 Manuale utente
Deutsch: Yamaha CLP-124 Benutzerhandbuch
svenska: Yamaha CLP-124 Användarmanual
português: Yamaha CLP-124 Manual do usuário
français: Yamaha CLP-124 Manuel utilisateur
Türkçe: Yamaha CLP-124 Kullanım kılavuzu
English: Yamaha CLP-124 User manual
dansk: Yamaha CLP-124 Brugermanual
русский: Yamaha CLP-124 Руководство пользователя
suomi: Yamaha CLP-124 Ohjekirja
Nederlands: Yamaha CLP-124 Handleiding
română: Yamaha CLP-124 Manual de utilizare

Powiązane dokumenty

Inne dokumenty

Vermeiren Kim Instrukcja obsługi