Lux Products 3M-22 Instrukcja obsługi

Marka: Lux Products

Model: 3M-22

Kategoria: Termostaty

Typ: Instrukcja obsługi

• Your thermostat is a precise instrument, handle it with care.

• Turn off electricity to the appliance before installing or

servicing thermostat or any part of the system.

• Do not turn electricity back on until work is completed.

• Do not short (jumper) across electric terminals at control on

furnace or air conditioner to test the system. This will damage

the thermostat and void your warranty.

• All wiring must conform to local codes and ordinances.

• This thermostat is designed for use with 24 volt AC and

millivolt systems. The thermostat should be limited to a

maximum of 1.0 amps; higher amperage may cause damage

to the thermostat.

Caution

Install guide 3M-22

ENGLISH

Location

Caution

Tools

To avoid electrical shock and to prevent damage to the furnace, air conditioner,

and thermostat, disconnect the power supply before beginning work.

This can be done at the circuit breaker, or at the appliance.

Replacement installations -

mount the new thermostat in place of the old one.

New installations -

follow the guidelines listed below.

• Locate the thermostat on an inside wall, about 5 ft. (1.5m) above the floor, and

in a room that is used often.

• Do not install it where there are unusual heating conditions, such as: in direct

sunlight; near a lamp, radio, television, radiator register, or fireplace; near hot

water pipes in a wall; near a stove on the other side of a wall.

• Do not locate in unusual cooling conditions, such as: on a wall separating an

unheated room; or in a draft from a stairwell, door, or window.

• Do not locate in a damp area. This can

lead to corrosion that will shorten thermostat

life.

• Do not locate where air circulation is poor,

such as: in a corner or an alcove; or behind

an open door.

• Do not install the unit until all construction

work and painting has been completed.

• This thermostat does not require leveling.

You will need a small Phillips screwdriver and possibly a drill

with 3/16-in. (4.8mm) bit for wall mounting.

Good

5ft.

(1.5m)

Install guide 3M-22

Remove old unit

Prepare wires

IMPORTANT : LABEL ALL WIRES

BEFORE DISCONNECTING THEM!

• Switch electricity to the furnace and

air conditioner OFF; then proceed with the

following steps.

• Remove cover from old thermostat. Most are

snap-on types and simply pull off. Some have

locking screws on the side or front. These must

be loosened. Note the letters printed near the terminals. Attach

labels (enclosed) to each wire for identification.

• Label the wires one at a time. You must label all the wires before

you proceed. With all wires labeled, remove them from the old unit.

• Make sure the wires do not fall back inside the wall. You can wind

them around a pencil to keep them from falling.

• Loosen all screws on the old thermostat and remove it from the wall.

• Fill wall opening with non-combustible insulation to prevent drafts.

Caution

Read instructions carefully before removing any wiring from existing thermostat.

Wires must be labeled before they are removed. THERE IS NO STANDARD

COLOR CODE. When removing wires from their terminals, ignore the color of

the wires since these may not comply with any standard.

• You will need at least 2.6" of wire for each

of your connections to the 3M-22.

• If you do not have enough wire, splice

additional wire to allow enough slack.

• Fan out wires below the hole as shown.

Trim

2.6"

Before you Connect Wires

Caution

Do not allow wires to touch each other or parts on thermostat.

Please follow these guidelines for safe and secure

wire connections.

• Easy Terminals do not require stripping the wire.

• Clip any bare wire from previous installation.

• Take care not to damage the labels for each wire in handling.

• Fan wires out as illustrated with 3M-22 below the wall opening.

• Wires will dress behind the 3M-22 and up over the terminal area.

• Use the Step-By-Step diagram as your guide.

• Do not bunch wires behind 3M-22. Feed slack back into the wall

opening.

• Insert the wire in the terminal and tighten

the screw securely.

• You will need to set Configuration

Jumpers per the Step-By-Step

diagram. A needle-nose plier may be

required to modify jumper positions

Determine which step-by-step wiring

diagram below you should use. Make

sure your wires are labeled. This may

require you to find the 'other end' connection for each wire on your heating or

air conditioning equipment and read the label there.

If you have a wire marked "C" it is optional. If you do connect it, the

thermostat will draw power from the C wire. This extends battery life.

What wires do you have?

Jumpers

•

If you combination of wires is not above you can use the

wiring table on pages 24-25 to determine your connections,

or call our USA support line at 1-888-607-5824 for help.

• Find the referenece page with your wiring

diagram and jumper set-up information.

Remember, the

wire is optional.

Find the set-up diagram for your system

Go To Page 18Go To Page 17Go To Page 16

Go To Page 21Go To Page 19

C W2 W Y Y2 RH G

2 stage Cool

2 stage Heat

C W Y RH RC G

5 Wire

Heat/Cool

C W Y RH G

4 Wire

Heat/Cool

C W RH G

3 Wire

Heat

C W RH

2 Wire

Heat

W RH A

3 Wire

Zoned

Hot Water

Go To Page 20

C B or O W2 Y RH G

5 Wire

Heat Pump

w/ Aux Heat

C B or O Y RH G

4 Wire Heat Pump

w/o Aux Heat

Go To Page 15

PAGE 22

Install AAA Batteries

• The 3M-22 requires 2 AAA batteries to operate .

• Switch MODE switch to OFF and the FAN switch to AUTO.

• Install 2 AAA alkaline batteries according to the polarity noted in

the compartment. LCD segments will go on.

• Press the RESET button (under top cover) to clear transient

program memory. NOTE: Replace the batteries when this LOW

battery indicator appears on the display or once a year.

• Replace top and bottom covers on unit.

Wall

Wires

3M-22

Wall anchor

• Hold the 3M-22 against the wall, with the wires coming

over the top above terminal block. The 3M-22 will cover the

hole in the wall.

• Position 3M-22 for best appearance. Use the optional stand-

offs if more space for wires is needed behind the 3M-22.

• Attach the base to the wall with the screws provided.

• If you are mounting the base to sheet rock or if you are using

the old mounting holes, use the plastic anchors provided. Drill

a 3/16-in.(4.8mm) hole for the insert at

each screw location, then mount the base.

Mount the 3M-22

AAA

NOTE: If you have labeled your wires, follow the correct Step-By-Step, and

these Check procedures do not operate your system call support at

1-888-607-5824

Check Unit

Follow these procedures to verify you

have correctly installed the 3M-22.

To check Fan: (If you connected the

G wire - fan relay)

• Switch the FAN switch to the ON

position. Verify that air is blowing from

the system. Return to AUTO position

for normal operation.

To check HEAT mode:

Set the mode switch to HEAT.

Set the fan switch to AUTO.

• Using the TEMP + button raise the Target Temp to 90deg.

Allow the system 2 min to respond.

• Verify that heat is blowing from the system.

To check COOL mode:

• Set the mode switch to COOL.

• Press the TEMP - button to a temp 5 degrees below the room temp.

Allow the system 2 minutes to respond.

• Verify that cool air is blowing from the system.

Congratulations, you have successfully installed your unit.

Please proceed to the OPERATING Guide to initialize the 3M-22.

TEMP

UP button

TEMP

DOWN button

Temperature

Display

Mode

Switch

Fan

Switch

BATTERIES ONLY - This thermostat can run on batteries only using 2AAA

alkaline batteries. The batteries will last at least 1 year; replace the batteries

once a year or when the low battery icon comes on the display. If the batteries

are not replaced, the thermostat will shut off the HVAC and then stop working.

24VAC - This thermostat can run on the HVAC 24VAC (C wire) if available.

As shown in the wiring diagrams, the C wire is the other side of the 24VAC

heating transformer and can be found where the other thermostat wires

connect at the wall or at the furnace. Do not use the common or ground side

of the line voltage. If the C wire is used, the batteries are then for back-up in

case of power loss only and will last much longer. With the C wire connected,

the thermostat will continue to work if the batteries die or are removed.

Power Options

NOTE:Your thermostat comes from the factory calibrated to +/- 1

of actual

temperature. It is an accurate instrument. If you want your thermostat to

display the same temperature as another thermometer in your home, you

can adjust its calibration.

To change the calibration:

Set the Mode switch to HEAT or COOL.

Locate the TIME SET button and press it. The

current calibration factor (+/-) of the 3M-22 will appear

in the LCD display as well as the modified temp.

Push the UP or DOWN arrows until the desired

calibration factor is reached.

Press HOME to save. The new calibrated temperature

will be displayed on the LCD.

Calibration

Calibrate button

2 WIRE HEAT Heating GAS MILLIVOLT or 24vac

NOTE: Wires marked with

dotted line are optional.

3 Wire Heat

3M-22

GAS Milivolt Heat

C B O W

Y Y

RH RC G A

3M-22

R G

HVAC SYSTEM

C B O W

Y Y

RH RC G A

STEP 1 - Connect the R (or RH) wire to the RH terminal on

the 3M-22. This connects the Heater Power to the thermostat.

STEP 2 - Connect the W wire to the W on the 3M-22.

This connects the heater control line to the 3M-22.

STEP 3 - Set Config jumpers per this diagram.

Your Heater is now connected to the 3M-22.

Please Go To Page 9

STEP 1 - Connect the R (or RH) wire to the RH terminal

on the 3M-22. This connects to the Heater Power .

STEP 2 - Connect the W wire to the W terminal on the

3M-22. This connects the heater control line to the

3M-22.

STEP 3 - Connect the G wire to the G terminal on the

thermostat. This connects the Fan to the 3M-22

STEP 4 - Set Config jumpers per this diagram. If you

have Electric heat set 5, if you have Gas or Oil set 7.

Your system is now connected to the 3M-22.

Please Go To Page 9

OPTIONAL POWER

SET JUMPERS

1 2 3

STEP 1 -

Connect the

wire to the

terminal on the

thermostat. This connects to the heater control line.

STEP 2 -

Connect the

wire to the

terminal on the

3M-22. This connects to the Cooler compressor.

STEP 3 -

Connect the

wire to the

terminal and the

wire to the

terminal on the 3M-22. This connects

the Heater and Cooler Power.

STEP 4 -

Connect the

wire to the

terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 5, if you have Gas or Oil set 7.

Your HVAC system is now connected

to the 3M-22.

Please Go To Page 9

STEP 1 -

Connect the

wire to the

terminal on the

thermostat. This connects to the heater control line.

STEP 2 -

Connect the

wire to the

terminal on the

3M-22. This connects to the Cooler compressor.

STEP 3 -

Connect the

wire to the

terminal on

the thermostat. This connects the Heater/Cooler Power.

STEP 4 -

Connect the

wire to the

terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 5, if you have Gas or Oil set 7.

Your HVAC system is now connected

to the 3M-22.

Please Go To Page 9

W Y RH G

4 Wire Heat/Cool

3M-22

Terminals

R G

HVAC SYSTEM

C B O W

Y Y

RH RC G A

OPTIONAL POWER

W Y RH RC G

5 Wire Heat/Cool

3M-22

Terminals

RH RC

HVAC SYSTEM

C B O W

Y Y

RH RC G A

OPTIONAL

1 2 3

SET JUMPERS

1 2 3

STEP 1 - Connect O wire to the O terminal or B wire to the B terminal on

the 3M-22. (If you have both O and B - connect O wire to O terminal

DO NOT connect B to B terminal - see pg 24 Trane for B wire terminal)

This connects the change-over valve.

STEP 2 - Connect the Y wire to Y on the 3M-22.

This connects the Compressor.

STEP 3 - Connect the R wire to RH on the 3M-22.

This connects to the 24vac power.

STEP 4 - Connect the G wire to the G terminal on the

3M-22. This connects the Fan.

STEP 5 - Set Config jumpers per this diagram.

Your HVAC system is now connected

to the 3M-22.

Please Go To Page 9

O Y R G

4 Wire Heat Pump w/o Aux

OPTIONAL POWER

STEP 1 - Connect O wire to the O terminal or B wire to the B terminal on

the 3M-22. (If you have both O and B -connect O wire to O terminal DO

NOT connect B to B terminal - see pg 24 Trane for B wire terminal)

STEP 2 - Connect the W2 wire to W2 on the 3M-22.

STEP 3 - Connect the Y wire to Y on the 3M-22.

STEP 4 - Connect the R wire to RH on the 3M-22.

STEP 5 - Connect the G wire to G on the 3M-22.

STEP 6 - Set Config jumpers per this diagram.

Set jumper 1 if you have Gas or Oil aux heat.

Your HVAC system is now connected

to the 3M-22.

Please Go To Page 9

O W2 Y RH G

5 Wire Heat Pump w/ Aux Heat

3M-22

Terminals

R G

HEAT PUMP SYSTEM

C B O W

Y Y

RH RC G A

SET JUMPERS

3M-22

Terminals

R G

HEAT PUMP SYSTEM

C B O W

Y Y

RH RC G A

OPTIONAL POWER

1 2 3

R A

Motor Valve

C B O W

Y Y

RH RC G A

W RH [A?] 3 Zoned Hot Water - Motor Valve

Step 1 - based on your valve type

Motor driven Valve- Connect the R (or RH) wire to the RH

terminal on the 3M-22. Connect the W wire to the W terminal

on the 3M-22. Connect the remaining wire to the A terminal.

Solenoid valve -Connect the R (or RH) wire to the RH

terminal on the 3M-22. Connect the W wire to the A terminal

on the 3M-22. Connect the remaining wire to the W

terminal.

STEP 2 - Set Config jumpers per this diagram.

Your system is now connected to the 3M-22.

Please Go To Page 9

STEP 1 -

Connect the

wire to the

terminal and

W2 on the 3M-22. This connects 2 stages of heat.

STEP 2 -

Connect the

wire to the

terminal and Y2 wire

to Y2 on the 3M-22. This connects 2 stages of cool.

STEP 3 -

Connect the

wire to the

terminal on

the thermostat. This connects the Heater/Cooler Power.

STEP 4 -

Connect the

wire to the

terminal on the

Thermostat. This connects to the Fan.

STEP 5 - Set Config jumpers per this diagram. If you

have Electric heat set 5, if you have Gas or Oil set 7.

Your HVAC system is now connected

to the 3M-22.

Please Go To Page 9

W2 W Y Y2 RH RC G

2 Stage Heat and Cool

3M-22

Terminals

3M-22

Terminals

W Y

HVAC SYSTEM

C B O W

Y Y

RH RC G A

OPTIONAL

POWER

SET JUMPERS

1 2 3

SET JUMPERS

1 2 3

This thermostat can be used with all millivolt and 24VAC heating and cooling systems. It

cannot be used with line voltage systems. This thermostat is digital and your desired heat or

cool temperatures can easily be set on the large screen with the +/- buttons on the front. A

minimum 4 minute off time protects heating and cooling systems from damage.

This thermostat uses a new technique called sequential staging for more comfort with

faster reaction to requested temperature changes. When using a heat pump with Aux heat, if

the heat pump cannot keep up and/or is

defective, remove jumper from position 8 and put

jumper on position 6 and the Aux heat will then

be your only source of heat. Be sure to restore it

to PUMP when the pump is again operational as

aux heat is more expensive than pump heat.

3M-22 Features

Wire Reference

Your Wires

Filtrete Terminal

R or V or VR RH and RC Single power for HEAT and COOL

RH or 4 RH Power for HEAT (RH not connected to RC)

RC RC Power for COOL (RH not connected to RC)

W W Heat control

W2 W2 2nd stage HEAT or heat pump auxiliary heat

? A 3rd wire for zoned hot water heat (see zoned)

Y Y COOL control

Y2 Y2 2nd stage COOL control

G or F G FAN control

C or X C Common 24VAC power (to power thermostat)

E Emergency heat (do not connect, tape off)

L System monitor (do not connect, tape off)

T Outdoor sensor (do not connect, tape off)

B or B Heat pump changeover (cool to heat, powered in heat)

O O Heat pump changeover (heat to cool, powered in cool)

B and O

SEE NOTE

B and O

NOTE: If

there are both

B and O wires

(Trane pump

products)

DO NOT

CONNECT B

to B terminal,

connect B to C

terminal

1002-005

Customer Support: 888-607-5824 or

Visit our website www.radiothermostat.com/filtrete

Printed in China

Wire Reference cont

Your Wires

Filtrete Terminal

Lennox Heat Pump

V or VR or R RH

M or Y Y

Y or W or W2 W2

F or G G

R or O O

X or X2 or C C

Trane Products [American Standard]

B C

W or W1 W2

Zoned Systems

Your Wires

Filtrete Terminal

2 wire Zoned Hot Water

R RH

W W

3 Wire Zoned Hot Water

Motor Driven Valves

R RH

W W

Y (the 3rd wire) A

3 Wire Zoned Hot Water

Solenoid Valves

R RH

W A

Y (the 3rd wire) W

PUMP AUX

ELECT

CELSIUS

321

OPEN

PUMP AUX

GAS OR OIL

FAHRENHEIT

CLOSED

CELSIUS

TYPE

AUX

FAHRENHEIT

HEAT

PUMP

HEAT PUMP'S

AUX ONLY

12 hr

24hr

12hr clock

24hr clock

CLOSED

OPEN

SINGLE

POWER(R)

RESET UNIT

GAS/ELEC HEAT

OPEN

POWER RH

POWER RC

AFTER CHANGING JUMPERS

GAS OR OIL

ELECTRIC

CLOSED

HEAT

OR PUMP

CLOSED

HVAC

POWER

SELECT

Jumper Reference

Configuration jumpers allow your

3M-22 to be adapted to many

different HVAC control applications.

NORM/PUMP/AUX

SELECT

Lux Products 3M-22 Instrukcja obsługi

Marka: Lux Products

Model: 3M-22

Kategoria: Termostaty

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

English: Lux Products 3M-22 User manual

Lux Products 3M-22 Instrukcja obsługi

Lux Products 3M-22 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty