Yamaha PM1D Instrukcja obsługi

EE

PM1D System Software V1.6

Supplementary Manual

PM1D System Software V1.6 Supplementary Manual

2

Copyright

Copying or distributing this manual in part or in whole using any method without the written permission of

Yamaha Corporation is prohibited.

Tr ade marks

Company names and product names are trademarks and registered trademarks of their respective owners.

Symbols such as ® and TM are not explicitly given in this document.

The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may

appear somewhat different from those on your instrument.

Contents

3

Contents

Additions and changes in V1.6 . . . . . . . . . . . . 4

Improvements to functions that were added

in V1.5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Panel Assign in the ST IN block . . . . . . . . . . . 5

Panel display of the unit name . . . . . . . . . . . 7

Channel name area added to the EQ CH and

LCR screens. . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Channel name area. . . . . . . . . . . . . . . . . . . . 8

DCA Auto Naming function. . . . . . . . . . . . . . . 9

DCA auto naming procedure . . . . . . . . . . . . 9

Input Channel Auto Naming function. . . . . . 11

Input Channel Auto Naming procedure . . . 11

Pan Nominal Position. . . . . . . . . . . . . . . . . . . 13

Pan Nominal Position procedure . . . . . . . . . 13

DCA Unity. . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DCA Unity procedure . . . . . . . . . . . . . . . . . 14

Scene Link Event . . . . . . . . . . . . . . . . . . . . . . 15

Scene Link Event procedure . . . . . . . . . . . . 15

Selective Recall . . . . . . . . . . . . . . . . . . . . . . . . 18

Extended functionality for Recall Safe. . . . . . 21

Recall Safe is now possible for compressor

and gate . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Clear Library. . . . . . . . . . . . . . . . . . . . . . . . . . 22

Extended functionality for the attenuators. . 23

Global Channel Copy . . . . . . . . . . . . . . . . . . . 24

CH COPY screen . . . . . . . . . . . . . . . . . . . . . 24

Using the Global Channel Copy function . . 25

Input Meter Bridge . . . . . . . . . . . . . . . . . . . . 27

FIXED CH mode . . . . . . . . . . . . . . . . . . . . . 28

FOLLOW PANEL mode . . . . . . . . . . . . . . . . 31

Parameter Lock/Console Lock . . . . . . . . . . . . 33

SECURITY screen . . . . . . . . . . . . . . . . . . . . . 33

Setting the System Password/Console

Password. . . . . . . . . . . . . . . . . . . . . . . . . . 34

Parameter Lock . . . . . . . . . . . . . . . . . . . . . . 35

Console Lock . . . . . . . . . . . . . . . . . . . . . . . 36

Surround panning . . . . . . . . . . . . . . . . . . . . . 37

SURR PRM screen . . . . . . . . . . . . . . . . . . . . 37

Internal settings and operation in surround

mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Making surround pan settings. . . . . . . . . . . 43

Cautions regarding surround pan . . . . . . . . 45

Multi-band dynamics processor. . . . . . . . . . . 46

File transfer mode . . . . . . . . . . . . . . . . . . . . . .47

Additional preference items . . . . . . . . . . . . . .48

Preset Effects Programs (added in V1.6) . . . .49

Effects Parameters (added in V1.6). . . . . . . . 49

Scene Memory/Effect Library to Program

Change Table. . . . . . . . . . . . . . . . . . . . . . . . .50

MIDI control change NRPN (Non Registered

Parameter Number) assignment table . . . . 50

MIDI Data Format . . . . . . . . . . . . . . . . . . . . . .53

PM1D System Software V1.6 Supplementary Manual

4

This supplementary manual explains the functionality that has been added or changed in PM1D system soft-

ware V1.6. Please use this manual in conjunction with the existing manuals.

*In cases where the console (CS1D) display differs from the screen of the PM1D Manager application program, expla-

nations that apply only to the PM1D Manager are distinguished by an indication of [PM1D Manager].

Additions and changes in V1.6

The additions and changes made in PM1D system software V1.6 are summarized below. For details on each

function, refer to the corresponding page.

■

Improvements to functions that were

added in V1.5 (

→

p.5)

Of the new functions that were added in V1.5, “Panel

Assign” and “Unit Name” have been improved.

■

Channel name area added to the EQ

CH and LCR screens (

→

p.8)

An area that displays the channel names has been

added to the EQ CH screens of the IN EQ function,

and to the LCR screen of the PAN/ROUTING.

■

DCA Auto Naming function (

→

p.9)

The DCA [NAME] indicator in the DCA GROUP

block can now be made to display the channel names

of the two last-assigned channels.

■

Input Channel Auto Naming function

(

→

p.11)

You can now make the INPUT block INPUT

[NAME] indicator always display the port name.

■

Pan Nominal Position (

→

p.13)

You now have the option of specifying that paired

input channels (or ST IN channels) will be at nomi-

nal level (0 dB) when panned to far left or right.

■

DCA Unity (

→

p.14)

When cue-monitoring a DCA group, it is now possi-

ble to always monitor the unity-level signal regard-

less of the state of the DCA fader or DCA [MUTE]

switch.

■

Scene Link Event (

→

p.15)

You can now cause a pre-programmed string of

MIDI events to be output from the desired MIDI

OUT connector when a speciﬁc scene is recalled.

■

Selective Recall (

→

p.18)

A Selective Recall function has been added, allowing

you to specify for each scene, parameters/channels

that will be excluded from recall when that scene is

recalled.

■

Extended functionality for Recall Safe

(

→

p.21)

The Recall Safe function has been extended, resulting

in slight changes to the Recall Safe screen, and add-

ing parameters that can be set to Recall Safe.

■

Clear Library (

→

p.22)

A CLEAR button has been added to each library

screen, allowing you to erase a library as desired.

■

Extended functionality for the attenua-

tors (

→

p.23)

The functionality of the input channel attenuators

has been expanded to allow cut/boost in a range of

–96 to +24 dB.

■

Global Channel Copy (

→

p.24)

Now you can choose desired parameters from the

currently selected channel, and copy them to multi-

ple channels of the same type in a single operation.

■

Input Meter Bridge (

→

p.27)

The levels of input channels and ST IN channels can

now be displayed in the meter bridge.

■

Parameter Lock/Console Lock (

→

p.33)

By specifying a password, the user can prevent cer-

tain parameters from being edited until the correct

password is input, or prohibit console operations.

■

Surround panning (

→

p.37)

Surround Pan functionality has been added, allowing

sounds from an input channel to be placed in a two-

dimensional space when a multi-channel playback

system is used.

■

Multi-band dynamics processor (

→

p.46)

A multi-band dynamics processor that includes an

independent compressor for each of three bands has

been added as an effect type for the internal effects.

■

File transfer mode (

→

p.47)

Data saved on a computer in which PM1D Manager

is installed can now be uploaded to the console, and

CS1D settings can be downloaded to the computer.

■

Additional preference items (

→

p.48)

The following items have been added to the UTIL-

ITY function PREFERENCE screen.

•

PROHIBIT DCA ASSIGN ON SELECTED CH

BLOCK

•

SKIP CONFIRMATIONS FOR MIX MINUS

SHORTCUT

•

LIBRARY PROTECTION

Improvements to functions that were added in V1.5

5

Improvements to functions that were added in V1.5

The following improvements have been made to the new functions that were added in V1.5.

Panel Assign in the ST IN block

In V1.5, a PANEL ASSIGN screen was added to the UTILITY function, allowing the combination of input channels and

ST IN channels reﬂected in the panel to be speciﬁed for each individual block.

PM1D System Software V1.6 Supplementary Manual

6

However for ST IN channels, the combinations that could be assigned to the panel were limited to the following four

possibilities.

•

The four combinations that were possible in V1.5

This limitation has been removed in V1.6. For example, any two ST IN channels of consecutive number such as ST IN

channels 1/2 and 5/6, or 1/2 and 7/8, can be combined freely. Also, if necessary, you may assign combinations of the same

ST IN channel to upper and lower ST IN blocks; e.g., ST IN channels 1/2 and 1/2, or ST IN channels 5/6 and 5/6.

12

34

12

56

78

56

ST IN

block 2

ST IN

block 1

ST IN

block 2

ST IN

block 1

ST IN

block 2

ST IN

block 2

ST IN

block 1

ST IN

block 1

Improvements to functions that were added in V1.5

7

Panel display of the unit name

In V1.5, the UNIT NAME screen added to the SYS/W.CLOCK function allowed you to assign a name to each port of each

input/output unit or card. In addition, if you turned on the UNIT NAME button in the NAME MODE area at the bot-

tom of the screen, the name of the port assigned to that channel would be displayed instead of the short name of the

input channel shown in the screen.

In V1.6 when you turn on the UNIT NAME button in the NAME MODE area, the INPUT [NAME] indicator in the

INPUT block will also show the name of the port assigned to that channel.

SEL

+

THR

-

COMP

+

THR

-

CLIP

6

12

18

30

60

GATE

+

THR

-

COMP

+

THR

-

GATE SEL

+

THR

-

COMP

+

THR

-

GATE SEL

+

THR

-

COMP

+

THR

-

GATE

CLIP

6

12

18

30

60

CLIP

6

12

18

30

60

CLIP

6

12

18

30

60

ONONONON

SEL

• INPUT block

Port name

PM1D System Software V1.6 Supplementary Manual

8

Channel name area added to the EQ CH and LCR screens

An area that displays the channel name of each channel has been added to the EQ CH screens (CH 1-24, CH

25-48, CH 49-72, CH 73-96, ST IN 1-8) of the IN EQ function and to the LCR screen of the PAN/ROUTING

function.

Channel name area

If the CH NAME button located in the NAME MODE area at the bottom of the display is turned on, this area will show

the short name of the corresponding channel.

•

EQ CH screen

•

LCR screen

When the UNIT NAME button is on, the name of the port assigned to that channel will be displayed.

•

EQ CH screen

•

LCR screen

Short name of the input channel

Port name of the input channel

Short name of the input channel

DCA Auto Naming function

9

DCA Auto Naming function

Normally, the DCA [NAME] indicator in the DCA GROUP block will display the name assigned to each DCA

group.

In V1.6, the channel names of the last-assigned two channels can also be displayed in the DCA [NAME] indi-

cator. (This is called the “DCA auto naming function.”)

DCA auto naming procedure

The auto naming procedure is as follows.

1. Access the IN PATCH/OUT PATCH function NAME

screen.

DCA name

1

2

3

4

PM1D System Software V1.6 Supplementary Manual

10

2. In the LIST SELECT area (

1

), move the cursor to

the DCA button and press the [ENTER] switch.

The name list (

2

) will show a list of the long names

(eight characters) assigned to each DCA group.

3. In the name list, move the cursor to the column of

the desired DCA group.

4. Make sure that the cursor is located at the ﬁrst

character of the text box (

3

) at right, and click the

DCA AUTO NAMING button of the character pal-

ette (

4

).

A highlighted “D” character will be input into the

character palette.

Hint

• If a PS/2 keyboard is connected to the CS1D, you

can also type Ctrl + D to input the highlighted “D”

character. (As a shortcut, you can hold down the

Ctrl key and type the ﬁrst character of the button

name in the character palette.)

• When you input the highlighted “D,” no further

characters can be input into the text box. Also, any

previously-input characters will be deleted.

• To delete the highlighted “D,” click the CLEAR

button.

5. Click the ENTER button at the right of the charac-

ter palette.

A highlighted “D” character will be input in the long

name ﬁeld of the name list.

The Auto Naming function is now enabled for the

corresponding DCA group. At this time, the DCA

[NAME] indicator will go dark if a channel has not

been assigned to the corresponding DCA group.

6. As necessary, perform the same operation for other

DCA groups.

7. Assign channels to the DCA groups for which you

performed steps 3–6.

For example if you assign input channels 1 and then

2 to DCA group 1, the corresponding DCA [NAME]

indicator will show the channel names of input chan-

nels 1/2.

If you then add input channel 3 to the same DCA

group, the DCA [NAME] indicator will change as

follows.

• Be aware that when you use the DCA Auto Nam-

ing function, the DCA [NAME] indicator will

show the short names of the two last-assigned

channels.

• A maximum of twelve channels of names will be

remembered for a DCA group. If a paired chan-

nel is assigned, the lower-numbered channel will

be displayed above.

• If you remove input channel 3 from DCA group 1

in the example described above, the display will

be blank.

Hint

• If you turn on the UNIT NAME button in the

NAME MODE area at the bottom of the screen,

the DCA [NAME] indicator will show the name of

the port assigned to that channel, instead of show-

ing the short name of the input channel.

• If you turn Cue Monitor on for a DCA group for

which Auto Naming is enabled, the channel that

was last assigned to that DCA group will be

selected (its [SEL] key will light).

Channel

names

Channel

names

Input Channel Auto Naming function

11

Input Channel Auto Naming function

As explained earlier, V1.5 added the capability of displaying the channel name or port name in the INPUT

[NAME] indicator of the INPUT block.

However if necessary, it is also possible to specify that the patched port name be always displayed as the input

channel name for only a speciﬁc input channel. This is referred to as the “Input channel auto naming function.”

Input Channel Auto Naming procedure

The auto naming procedure is as follows.

1. Access the IN PATCH/OUT PATCH function NAME

screen.

2. In the LIST SELECT area (1), move the cursor to

the INPUT button and press the [ENTER] switch.

The name list (2) will show a list of the short names

(four characters) and long names (eight characters)

assigned to each input channel.

3. In the name list, select the desired input channel,

and move the cursor to the short name ﬁeld.

4. Make sure that the cursor is located at the ﬁrst

character of the text box (3) at right, and click the

UNIT NAME ASSIGN button of the character pal-

ette (4).

A highlighted “U” character will be input into the

character palette.

1

2

3

4

PM1D System Software V1.6 Supplementary Manual

12

Hint

• If a PS/2 keyboard is connected to the CS1D, you

can also type Ctrl + U to input the highlighted “U”

character. (As a shortcut, you can hold down the

Ctrl key and type the ﬁrst character of the button

name in the character palette.)

• When you input the highlighted “U,” no further

characters can be input into the text box. Also, any

previously-input characters will be deleted.

• To delete the highlighted “U,” click the CLEAR

button.

5. Click the ENTER button at the right of the charac-

ter palette.

A highlighted “U” character will be input in the short

name ﬁeld of the name list.

The Auto Naming function is now enabled for the

corresponding input channel. Now the port name

assigned to the channel will always be displayed in

areas of the screen that display the short name of the

corresponding channel, and in the corresponding

INPUT [NAME] indicator of the panel.

Hint

It is also possible to select the long name ﬁeld instead

of the short name ﬁeld in step 3. In this case, the port

name will always be displayed in areas of the screen

that display the long name of the corresponding

channel.

Pan Nominal Position

13

Pan Nominal Position

Normally if a signal sent from an input channel to the stereo bus is panned to the far-left or far-right position,

the level will increase by +3 dB compared to when the signal is panned to the center. This is done so that a

constant volume (energy) will be output whether the signal is mono or stereo; however when inputting a ste-

reo source such as a synthesizer or CD player, you may consider this an inconvenience.

Thus, V1.6 adds the option of specifying that only paired input channels (or ST IN channels) will be at nomi-

nal level (0 dB) when pan is set to far left or right.

Pan Nominal Position procedure

Use the following procedure to enable this option.

1. Access the PAN/ROUTING function CH to MIX

screen.

The PAN NOMINAL POSITION ﬁeld has been

added to this screen.

• CENTER ......... If this button is on, all input chan-

nels and ST IN channels will be at

nominal level (0 dB) when panned

to the center, and +3 dB when

panned fully left or right. (This is

the default setting.)

• L ⇔ R.............. If this button is on, paired input

channels and ST IN channels will

be at –3 dB when panned to the

center, and at nominal level when

panned fully left or right (L63 or

R63).

2. Move the cursor to the L ⇔ R button and press the

[ENTER] switch.

A popup window will ask you to conﬁrm the

changed Pan Nominal setting.

3. Move the cursor to the OK button and press the

[ENTER] switch.

4. Enable pairing for the desired channels, and make

sure that a mode other than BALANCE is selected

as the pan mode.

In this state, panning fully left or right will produce a

nominal level only for paired input channels and for

ST IN channels.

• Pan Nominal Position does not affect unpaired

monaural input channels.

• Even in the case of a paired input channel (or a

ST IN channel), this setting has no effect if the

pan mode is set to BALANCE.

• In the case of L-MONO or R-MONO, this setting

has no effect; however in the LR-MONO state,

changes in the Pan Nominal Position setting will

be valid.

• When you change the Pan Nominal Position set-

ting, the MIX SEND PAN of signals being sent to

paired MIX buses will also be switched.

• The Pan Nominal Position of each input channel

can be viewed in the graph in the PAN/ROUT-

ING function LCR screen.

Hint

By setting Pan Nominal Position to L ⇔ R, you can

minimize changes in level that occur when a paired

channel is switched between PAN, BALANCE, L-

MONO, R-MONO, or LR-MONO.

PM1D System Software V1.6 Supplementary Manual

14

DCA Unity

When cue-monitoring a DCA group, it is now possible to always monitor the unity-level signal.

In previous versions, even when you pressed the DCA [CUE] switch, you could not monitor the signal of a

DCA group whose DCA fader was lowered or whose DCA [MUTE] switch was on.

However in V1.6, you have the option of always monitoring the DCA group at unity level (the level equivalent

to setting the DCA fader at 0 dB).

DCA Unity procedure

To use this option, access the MONI/CUE function CUE/SOLO screen, and turn on the DCA UNITY ON/OFF button

that has been added to the DCA area.

If this button is on, pressing the DCA [CUE] button

allows you to monitor that DCA group at unity level,

regardless of the current position of the DCA fader or

the on/off state of the DCA [MUTE] switch.

Hint

• The setting of the DCA UNITY ON/OFF button

does not affect the individual channels included in

the DCA groups.

• If the fader of a channel included in the DCA

group is lowered or if its [ON] switch is turned off,

you will not be able to monitor that channel via the

DCA group.

DCA UNITY ON/OFF button

Scene Link Event

15

Scene Link Event

You can now cause a string of MIDI events to be output from the desired MIDI OUT connector when a spe-

ciﬁc scene is recalled. (This is called the “Scene Link Event” function.)

By using this function to pre-program MIDI events for each scene, you can modify the internal settings of an

external device when that scene is recalled, or automatically start the transport of an external device.

Scene Link Event procedure

Here’s how to program MIDI events for each scene.

1. Access the SCENE function MEMORY screen.

2. In the list, click the row for the desired scene to

select it.

You cannot program MIDI events for a READ

ONLY scene or a protected scene.

3. Click the STORE button in the lower left of the

screen.

The SCENE STORE popup window will appear,

allowing you to assign a title or comment and store

the scene.

STORE button

PM1D System Software V1.6 Supplementary Manual

16

4. Click the COMMENT/MIDI EVENT ﬁeld to select

it.

The EVENT CODE SET button will appear at the

lower left of the character palette.

5. Click the EVENT CODE SET button.

The characters in the COMMENT/MIDI EVENT

ﬁeld will be erased, and a highlighted “M” character

will be input in their place. Also, the characters in the

character palette will be grayed-out except for 1, 2,

and E, and will be unavailable for input.

Hint

• If a PS/2 keyboard is connected to the CS1D, you

can also type Ctrl + E to input the highlighted “M”

character. (As a shortcut, you can hold down the

Ctrl key and type the ﬁrst character of the button

name in the character palette.)

• To erase the highlighted “M,” click the CLEAR but-

ton.

6. Click either 1, 2, or E in the character palette to

select the MIDI OUT connector from which the

MIDI event will be output.

The numerals or “E” character correspond to the fol-

lowing MIDI OUT connectors.

• 1....................... MIDI OUT connector of console 1

• 2....................... MIDI OUT connector of console 2

(if using Dual Console mode)

• E ...................... MIDI OUT connector of the

engine

The highlighted numeral or “E” character will be

added to the COMMENT/MIDI EVENT ﬁeld. Also,

characters in the characters palette other than 0–9

and A–F will be grayed-out, and will be unavailable

for input.

7. Use the 0–9 and A–F characters of the character

palette to directly input the MIDI event in hexadec-

imal format.

Two hexadecimal characters correspond to one byte

of the MIDI message.

8. When you have ﬁnished inputting the MIDI event,

click the AUTO STORE button or the MANUAL

STORE button.

The MIDI event you input will be stored in the scene.

You can check the contents of the MIDI event by

scrolling to the right edge of the scene list in the

MEMORY screen.

When you recall this scene, the MIDI event will be

transmitted from the speciﬁed MIDI OUT connec-

tor.

• The PM1D system is in no way aware whether the

MIDI message you input is a valid one. Please use

care when inputting the message.

• You can input a maximum of 32 bytes into the

COMMENT/MIDI EVENT ﬁeld, calculated as

follows. Since a total of two bytes are used by the

highlighted “M” and the character that speciﬁes

the output destination, you can input a maxi-

mum of 30 bytes of MIDI data here.

[Calculation method]

• One comment character .....................1 byte

• Highlighted “M”..................................1 byte

• Highlighted “1”....................................1 byte

• Highlighted “2”....................................1 byte

• Highlighted “E” ...................................1 byte

• Two characters of the MIDI message .1 byte

COMMENT/MIDI EVENT ﬁeld

Scene Link Event

17

• It is possible to input two or more messages, as

long as the total stays within 32 bytes. However

you should be aware that, depending on the type

of message, the receiving device may not be able

to process MIDI events received in immediate

succession.

• If you input more than 32 bytes, a warning of

“LENGTH OVER!” will be displayed, and you

will not be able to press the STORE button.

Delete characters until the warning is no longer

displayed.

• You cannot input “FE” (Active Sensing) as a

MIDI code.

• While inputting the MIDI event, you can click

the EVENT CODE SET button and insert the

event that speciﬁes the output destination. This

lets you output events to different MIDI OUT

connectors.

• ƒEven if you recall a scene for which a fade time is

set, the MIDI event will be transmitted immedi-

ately after the scene is recalled.

PM1D System Software V1.6 Supplementary Manual

18

Selective Recall

In V1.6 you can restrict the parameters/channels that will be recalled when a speciﬁc scene is recalled, or con-

versely specify parameters/channels that will be excluded from the recall operation for a speciﬁc scene. (This

function is called “Selective Recall.”)

In previous versions, you could use a function called Recall Safe to select channels/parameters that would be

excluded from recall operations. These Recall Safe settings are global, and are common to all scenes. (Chan-

nels/parameters excluded from a recall operation do not change when any scene is recalled.) In contrast, the

Selective Recall function lets you store – for each scene – a combination of parameters/channels that will be

recalled, or conversely a combination of parameters/channels that will be excluded from the recall operation.

This lets you create partial scene images for store/recall, using them in a way similar to libraries.

So that you can universally enable/disable the Selective Recall function settings saved in each scene, a BYPASS

button has been added to the MEMORY screen SELECTIVE RECALL FUNCTION area.

V1.6 adds a SELECTIVE RECALL screen to the SCENE function, allowing you to make Selective Recall set-

tings.

1 SELECTION MODE

Use the following two buttons to select how you want

to use the SELECTIVE RECALL screen.

• RECALL PARAMETER button

If this button is on, you can use the buttons in the

screen to select the channels/parameters that will be

affected by a recall operation.

• SAFE PARAMETER button

If this button is on, you can use the buttons in the

screen to select the channels/parameters that will be

excluded from a recall operation.

1

Selective Recall

19

Hint

Each time you switch between the RECALL PARAM-

ETER button and the SAFE PARAMETER button,

the settings in the screen will be initialized as follows.

• When you switch to the RECALL PARAMETER

button, all channels will be set to RECALL ON/

OFF button = On and RECALL PARAMETER

SELECT = ALL.

• When you switch to the SAFE PARAMETER but-

ton, all channels will be set to SAFE ON/OFF but-

ton = Off and SAFE PARAMETER SELECT = ALL.

2 ENABLE/DISABLE button

This button enables (button indicates ENABLE) or

disables (button indicates DISABLE) the Selective

Recall function individually for each scene.

3 RECALL ON/OFF button

SAFE ON/OFF button

This button selects the channel that will be affected.

The function of this button will change depending

on the mode you select in the SELECTION MODE

area (1).

• If RECALL PARAMETER is on

This button will function as the SAFE ON/OFF but-

ton to specify channels that will be affected by recall

operations.

• If SAFE PARAMETER is on

This button will function as the SAFE ON/OFF but-

ton to specify channels that will be excluded from

recall operations.

The input channels/output channels for which this

function can be set are the same as in the SCENE

function RECALL SAFE screen.

4 RECALL PARAMETER SELECT button

SAFE PARAMETER SELECT button

This button selects the parameter that will be

affected. The function of this button will change

depending on the button you select in the SELEC-

TION MODE area (1).

• If RECALL PARAMETER is on

This button will function as the RECALL PARAME-

TER SELECT button to specify parameters that will

be affected by recall operations.

• If SAFE PARAMETER is on

This button will function as the SAFE ON/OFF but-

ton to specify parameters that will be excluded from

recall operations.

The types of parameters for which this function can

be set are the same as in the SCENE function

RECALL SAFE screen, with the exception that you

cannot specify UNIT (a unit patched to an input

channel) as an input channel.

5 SET ALL

If you click this button, all corresponding parameter

buttons will be turned on.

6 CLEAR ALL

If you click this button, all corresponding parameter

buttons will be turned off.

7 OTHERS

Use these buttons to select parameters other than the

above. The function of these buttons will change

depending on the button that is selected in the

SELECTION MODE area (1).

• If RECALL PARAMETER is on

These buttons select the parameters that will be

affected by recall operations.

2

3

4

5

6

7

PM1D System Software V1.6 Supplementary Manual

20

• If SAFE PARAMETER is on

These buttons select the parameters that will be

excluded from recall operations.

The parameters that can be selected are the same as

in the SCENE function RECALL SAFE screen, with

the exception that there is no MUTE MASTER (on/

off for all mute groups).

In the case of parameters for which there is only one

parameter for two adjacent odd-numbered/even-

numbered channels (such as the parameters listed

below), the parameter will be excluded from the

recall operation only if both channels are speciﬁed

for selective recall.

• HA GAIN GANG

• HA A/B LINK

• GATE LINK

• COMP LINK

• DELAY GANG

• PAN MODE

• GEQ LINK

Hint

All of the Selective Recall settings will be linked for

two paired channels, ST IN channels, or STEREO A/

B channels.

• Recall Safe and Selective Recall may be used

together. Channels/parameters that are set to

Recall Safe, or channels/parameters for which the

Selective Recall settings of the scene being

recalled exclude them from recall operations, will

not be recalled.

• If a scene is recalled in PREVIEW mode, Selective

Recall has no effect.

• If, when a scene is recalled, a conﬂict in pairing

settings occurs between Recall Safe and Selective

Recall, that pairing will be forcibly defeated. (The

channel that is excluded from the recall will

maintain all its parameters in the state prior to

recall.)

• However if two channels are paired in the current

scene, and only one of these channels is set to Safe

by the Selective Recall settings of the scene you

are recalling, recalling that scene will cause both

channels to be Safe, and the state prior to recall

will be maintained.

• If MIX channels set to Selective Recall have dif-

fering mix types (VARI or FIX) before and after

recall, the mix type before recall will apply.

• If you set the SELECTIVE RECALL ENABLE/

DISABLE button to ENABLE, and store a scene

in which all channels/all parameters are excluded

from recall operations, no parameters will change

when you next recall that scene. In such cases,

you can temporarily disable Selective Recall by

turning on the BYPASS button in the SELEC-

TIVE RECALL FUNCTION area of the SCENE

function MEMORY screen, so that you will be

able to recall the previous scene.

• If you later want to make changes to the combi-

nation of channels/parameters that were set to

Selective Recall, access the SCENE function

MEMORY screen, and in the SELECTIVE

RECALL FUNCTION area, turn the BYPASS

switch on before you recall that scene. Alterna-

tively, you can recall the scene in PREVIEW

mode. Then use the SELECTIVE RECALL screen

to edit the combination of channels/parameters,

and store the scene again into the same scene

number.

• If you recall a scene in which the RECALL

PARAMETER button = On and the ENABLE/

DISABLE button = ENABLE, parameters apply-

ing to the entire scene (such as fade time

ENABLE/DISABLE and TIME parameters, and

Pan Nominal Position) will not be recalled.

Strona się ładuje...

Yamaha PM1D Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Yamaha PM1D Instrukcja obsługi

w innych językach

Powiązane artykuły