Whirlpool AKZM 656/IX/01 instrukcja

User and maintenance manual

Instrukcja obslugi i konserwacji

Руководство по эксплуатации

и техническому обслуживанию

Manual de utilizare şi întreţinere

EN

EN3

These instructions shall also be available on website: www.whirlpool.eu

YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

All safety warnings give specific details of the potential risk present

and indicate how to reduce risk of injury, damage and electric shock

resulting from improper use of the appliance. Carefully observe the

following instructions:

- Use protective gloves to perform all unpacking and installation

operations.

- The appliance must be disconnected from the power supply before

carrying out any installation work.

- Installation and maintenance must be carried out by a qualified

technician, in compliance with the manufacturer’s instructions and

local safety regulations. Do not repair or replace any part of the

appliance unless specifically stated in the user manual.

- Power cable replacement must be carried out by a qualified

electrician. Contact an authorized service centre.

- Regulations require that the appliance is earthed.

- The power cable must be long enough for connecting the

appliance, once fitted in its housing, to the main power supply.

- For installation to comply with current safety regulations, an all-

pole disconnect switch with minimum contact gap of 3 mm must

be utilized.

- Do not use multiple plug adaptors if the oven is fitted with a plug.

- Do not use extension leads.

- Do not pull the power supply cable.

- The electrical components must not be accessible to the user after

installation.

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER

Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

EN4

- If the surface of the induction plate is cracked, do not use it and

switch off the appliance to avoid the possibility of electric shock

(only for models with induction function).

- Do not touch the appliance with any wet part of the body and do

not operate it when barefoot.

- This appliance is designed solely for use as a domestic appliance

for cooking food. No other type of use is permitted (e.g.: heating

rooms). The Manufacturer declines all responsibility for

inappropriate use or incorrect setting of the controls.

- The appliance and its accessible parts become hot during use.

Care should be taken to avoid touching heating elements.

Very young (0-3 years) and young children (3-8 years) shall

be kept away unless continuously supervised.

- Children from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and

knowledge can use this appliance only if they are supervised or

have been given instructions on safe appliance use and if they

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

- During and after use, do not touch the heating elements or interior

surfaces of the appliance - risk of burns. Do not allow the appliance

to come into contact with cloths or other flammable materials until

all the components have cooled down completely.

- At the end of cooking, exercise caution when opening the

appliance door, letting the hot air or steam exit gradually before

accessing the oven. When the appliance door is shut, hot air is

vented from the aperture above the control panel. Do not obstruct

the vent apertures.

- Use oven gloves to remove pans and accessories, taking care not to

touch the heating elements.

- Do not place flammable materials in or near the appliance: a fire

may break out if the appliance is inadvertently switched on.

- Do not heat or cook sealed jars or containers in the appliance.

The pressure that builds up inside might cause the jar to explode,

damaging the appliance.

EN5

- Do not use containers made of synthetic materials.

- Overheated oils and fats catch fire easily. Always remain vigilant

when cooking foods rich in fat and oil.

- Never leave the appliance unattended during food drying.

- If alcoholic beverages are used when cooking foods (e.g. rum,

cognac, wine), remember that alcohol evaporates at high

temperatures. As a result, there is a risk that vapours released

by the alcohol may catch fire upon coming into contact with the

electrical heating element.

- Never use steam cleaning equipment.

- Do not touch the oven during the pyrolysis cycle. Keep children

away from the oven during the pyrolysis cycle. Excess spillage must

be removed from the oven cavity before cleaning cycle (only for

ovens with Pyrolysis function).

- Only use the temperature probe recommended for this oven.

- Do not use harsh abrasive cleaners or sharp metal scrapers to clean

the oven door glass since they can scratch the surface, which may

result in shattering of the glass.

- Ensure that the appliance is switched off before replacing the lamp

to avoid the possibility of electric shock.

- Do not use aluminium foil to cover food in the cooking vessel (only

for ovens with cooking vessel supplied).

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal

regulations. Before scrapping, cut off the power supply cable.

- For further information on the treatment, recovery and recycling of household electrical appliances, contact your

competent local authority, the collection service for household waste or the store where you purchased the appliance.

After unpacking the oven, make sure that it has not been damaged during transport and that the oven door closes properly.

In the event of problems, contact the dealer or your nearest After-sales Service. To prevent any damage, only remove the oven

from its polystyrene foam base at the time of installation.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all wood chips and sawdust.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the upper edge of the oven.

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The dataplate is on the front

edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm

2

) must be carried out by a qualified electrician. Contact an

authorized service centre.

INSTALLATION

EN6

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective film and adhesive labels from accessories.

- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell and fumes from the

insulating materials and protective grease.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Never pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become trapped in the door.

- Do not expose the oven to atmospheric agents.

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must

therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment

(WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it should not be treated as

domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic

equipment.

Energy saving

- Only pre-heat the oven if specified in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will continue to cook even

once the oven is switched off.

- This oven, which is intended to come into contact with foodstuffs, complies with European Regulation ( ) n.1935/2004

and has been designed, manufactured and sold in conformity with the safety requirements of the “Low Voltage” directive

2006/95/CE (which replaces 73/23/CEE and subsequent amendments), the protection requirements of “EMC” 2004/108/CE.

The oven does not work:

• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.

• Turn off the oven and restart it to see if the fault persists.

The door will not open:

• Turn off the oven and restart it to see if the fault persists.

• Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see paragraph “Cleaning

cycle of ovens with pyrolysis function”).

The electronic programmer does not work:

• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service. Specify in this case the

number that follows the letter “ ”.

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

TROUBLESHOOTING GUIDE

EN7

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide“.

2. Switch the appliance off and back on again it to see if the fault persists.

If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right hand edge of the oven cavity

(visible when the oven door is open). The service number is also indicated on the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-sales Service (to guarantee that original spare parts will be used

and repairs carried out correctly).

Oven exterior

IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with

the appliance, clean immediately with a damp cloth.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing up detergent to the water. Finish off

with a dry cloth.

Oven interior

IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin enamelled surfaces

and the oven door glass.

• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove built-up dirt and

stains caused by food residues (e.g. food with a high sugar content).

• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.

• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate cleaning

(see MAINTENANCE).

• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean the roof of the oven.

N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.) condensation may form

on the inside of the door and around the seal. When the oven is cold, dry the inside of the door with a cloth or sponge.

Accessories:

• Soak the accessories in water with washing up detergent immediately after use, handling them with oven gloves if still hot.

• Food residues can be easily removed using a brush or sponge.

Cleaning the rear wall and catalytic side panels of the oven (if present):

IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven sprays which could

damage the catalytic surface and ruin its self-cleaning properties.

• Operate the oven empty with the fan-assisted function at 200°C for about one hour

• Next, leave the appliance to cool down before removing any food residue with a sponge.

AFTER-SALES SERVICE

CLEANING

WARNING

- Never use steam cleaning equipment.

- Only clean the oven when it is cool to the touch.

- Disconnect the appliance from the power supply.

EN8

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (fig. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (fig. 2).

To refit the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles (Fig. 3).

2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).

3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to rest on the lateral

supports.

REPLACING THE OVEN LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the power supply.

2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover back on.

3. Reconnect the oven to the power supply.

To replace the side lamp (if present):

1. Disconnect the oven from the power supply.

2. Remove the side accessory holder grilles, if present (Fig. 3).

3. Use a screwdriver to prise off the lamp cover (Fig. 7).

4. Replace the lamp (see note for lamp type) (Fig. 8).

5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).

6. Refit the side accessory holder grilles.

7. Reconnect the oven to the power supply.

N.B.:

- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C halogen lamps.

MAINTENANCE

WARNING

- Use protective gloves.

- Ensure the oven is cold before carrying out the following operations.

- Disconnect the appliance from the power supply.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Fig. 6 Fig. 7 Fig. 8 Fig. 9

EN9

- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for household room

illumination (Commission Regulation (EC) No 244/2009).

- Lamps are available from our After-sales Service.

IMPORTANT:

- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.

- Do not use the oven until the lamp cover has been repositioned.

EN10

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Dataplate (not to be removed)

5. Lamps

6. Circular heating element (not visible)

7. Fan

8. Turnspit (if present)

9. Lower heating element (not visible)

10. Door

11. Position of shelves (the number of shelves is indicated on the front of the oven)

12. Rear wall

N.B.:

- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a

while.

- When the oven door is opened during cooking, the heating elements switch off.

ACCESSORIES SUPPLIED

A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other

ovenproof cooking receptacles.

B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as

an oven tray for cooking meat, fish, vegetables, focaccia, etc.

C. BAKING TRAY: for cooking all bread and pastry products, but also roasts, fish en papillotte, etc.

D. CATALYTIC PANELS: for easier and more thorough cleaning of the oven walls.

E. SLIDING RUNNERS: to facilitate insertion and removal of accessories.

The number of accessories may vary according to which model is purchased.

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-sales Service.

INSTRUCTIONS FOR OVEN USE

Fig. A Fig. B Fig. C Fig. D Fig. E

1

12

5

2

4

8

5

9

11

10

7

6

3

EN11

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).

2. The other accessories, like the drip tray and baking tray, are inserted with the raised part on the flat

section “B” facing upwards (Fig. 2).

CONTROL PANEL DESCRIPTION

TOUCH KEYS: to use, simply touch the corresponding symbol (a light touch is all that is required).

On/Off (when you press on / off button to turn off the oven an acoustic signal will sound, this sound can

not be disabled).

to access the main MENU or return to the start screen

to access the 10 most used functions

to return to the previous screen

to browse the functions/options and change pre-set values

to select and confirm settings

to start cooking

LIST OF FUNCTIONS

After switching on the oven, press the symbol and the display will show the following indications.

A. Symbol for highlighted function

B. Highlighted function can be selected by pressing

C. Description of highlighted function

D. Further available, selectable information

DETAILS OF FUNCTION

After selecting the desired function, press button and the display will show further options and related

details.

To move between different areas, use buttons and : the cursor moves to the adjustable values,

following the order described above. Press to select the value, adjust it using and confirm by

pressing button .

Fig. 1 Fig. 2

DISPLAY

Cooking nished at 19:10

Traditional manual cooking functions

Specials

Recipes

Traditional

A

D

C

B

PREHEAT

No

GRILL POWER

Medium

COOK TIME

END TIME

Grill

--:--

Zone 1 Zone 3

Cursor

Zone 4

Zone 2

EN12

USING THE APPLIANCE FOR THE FIRST TIME - LANGUAGE SELECTION AND SETTING

THE TIME

For correct use of the oven, when it is switched on for the first time you will have to select the desired

language and set the correct time.

Proceed as follows:

1. Press : the display will show the list of the first three available languages.

2. Press buttons and to scroll down the list.

3. When the desired language is highlighted, press to select it.

After language selection, the display will flash 12:00.

4. Set the time using buttons and . To scroll through the numbers more quickly, keep the button

pressed.

5. Confirm your setting by pressing : the display will show the list of functions.

SELECTING COOKING FUNCTIONS

1. If the oven off press button ; the display will show the cooking functions.

2. To browse the various possibilities, press buttons : the selectable function is highlighted in

white in the centre of the screen.

N.B.:for the list and description of functions, see the specific table at page16 and at page17.

3. Select the function by pressing button : the cooking settings are displayed on the screen. If the

pre-set values are those desired, press the start button , otherwise proceed as inidcated above to

change them.

SETTING THE TEMPERATURE/OUTPUT OF THE GRILL

To change the temperature or output of the grill, proceed as follows:

1. Check that the cursor is positioned next to the temperature value (zone 1); press button to select

the parameter to be changed: the temperature values flash.

2. Use buttons to change to the desired value.

3. Press button to confirm and then press . The display indicates which shelf food should be

placed on.

4. Press to start cooking.

The set temperature can also be changed during cooking by following the same procedure.

5. At the end of cooking, the end of cooking message is displayed. At this point the oven can be

switched off by pressing , or cooking can be prolonged by pressing . When switched off,

the display shows the cooling bar which indicates the temperature inside the oven.

PREHEATING THE OVEN

If you wish to preheat the oven before inserting food, change the oven’s default selection as follows:

1. Using buttons and , move the cursor to preheating.

2. Press button to select the setting: “No” flashes on the display.

3. To change the setting, press or : the display shows “Yes”.

4. To confirm your choice, press button .

Traditional manual cooking functions

Specials

Recipes

Traditional

PREHEAT

No

TEMPERATURE

200°C

COOK TIME

END TIME

Forced Air

--:--

PREHEAT

No

TEMPERATURE

180°C

COOK TIME

END TIME

Forced Air

--:--

Insert food on level 3

Press when done

PREHEAT

No

TEMPERATURE

180°C

COOK TIME

END TIME

Forced Air

--:--

PREHEAT

No

TEMPERATURE

180°C

COOK TIME

END TIME

Forced Air

--:--

PREHEAT

Yes

TEMPERATURE

180°C

COOK TIME

END TIME

Forced Air

--:--

EN13

FAST PREHEATING

If you wish to preheat the oven quickly before inserting food, change the oven’s default selection as

follows:

1. Select the fast preheating function using buttons .

2. Confirm by pressing : the settings are displayed on the screen.

3. If the proposed temperature is that desired, press , otherwise proceed as described in previous

paragraphs to change it. An acoustic signal will sound when the oven has reached the set temperature.

At the end of preheating, the oven automatically selects the conventional function .

At this point food can be placed in the oven for cooking.

4. If you wish to set a different cooking function, press and select the desired function.

SETTING COOKING TIME

This function can be used to cook food for a set length of time, from a minimum of 1 minute to the

maximum time allowed by the selected function, after which the oven switches off automatically.

1. To select the function, position the cursor next to “COOK TIME” using buttons .

2. Press button to select the setting; “00:00” flashes on the display.

3. Change the value using buttons and to display the desired cooking time.

4. Confirm the selected value by pressing button .

BROWNING

At the end of cooking, with certain functions, the display indicates the possibility of browning the surface of

your dish. This function can only be used when cooking time has been set.

At the end of cooking time, the display shows “^ to prolong, to brown”. Press button , and the oven

starts a 5 minute browning cycle. This function can only be used once after cooking.

SETTING END OF COOKING TIME / DELAYED START

The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and

59 minutes. This can only be done once cooking time has been set. This setting is only possible when

pre-heating is not required for the selected function.

After setting cooking time, the display shows the end of cooking time (for example 19:20). To delay the end

of cooking time, and thus also the cooking start time, proceed as follows:

1. Position the cursor next to the end of cooking time using buttons .

2. Press button to select the setting: the end of cooking time flashes.

3. To delay the end of cooking time, use buttons and to set the desired value.

4. Confirm the selected value by pressing button .

5. Press button . The display indicates which shelf food should be placed on.

6. Press button to activate the function. The oven will start cooking after a period of time calculated

so as to finish cooking at the set time (for example, in the case of a dish which requires a cooking time

of 20 minutes, if the end of cooking time is set to 20:10, the oven will begin cooking at 19:50).

N.B.:during the interval before cooking starts, the oven can in any case be switched on by pressing

button .

TEMPERATURE

180°C

INSERT IN

Fast Preheating

- 00:02

TEMPERATURE

180°C

INSERT IN

Preheating

- 00:02

TEMPERATURE

180°C

INSERT IN

Oven is Hot!

- 00:02

PREHEAT

No

TEMPERATURE

180°C

COOK TIME

END TIME

Forced Air

--:--

PREHEAT

No

TEMPERATURE

180°C

HH:MM

END TIME

Forced Air

--:--

- 00:00

PREHEAT

No

TEMPERATURE

180°C

HH:MM

END TIME

Forced Air

19:20

- 00:20

Browning

COOK TIME

END TIME

20:05

- 00:05

Cooking nished at 20:00

^ to prolong, 3 to brown

Browning nished at 20:05

PREHEAT

No

TEMPERATURE

180°C

HH:MM

END TIME

Forced Air

19:20

- 00:20

PREHEAT

No

TEMPERATURE

180°C

HH:MM

END TIME

Forced Air

19:20

- 00:20

PREHEAT

No

TEMPERATURE

180°C

HH:MM

END TIME

Forced Air

20:10

- 00:20

EN14

At any time during cooking, set values (temperature, grill setting, cooking time) can be changed

using buttons and button as described in previous paragraphs.

TIMER

This function can be used only with the oven switched off and is useful, for example, for monitoring the

cooking time of pasta. The maximum time which can be set is 1 hour 30 minutes.

1. With the oven switched off, press button : the display will show “00:00:00”.

2. Press buttons and to select the desired time.

3. Press button to start the countdown. When the set time has elapsed, the display will show

“00:00:00” and an acoustic signal will sound. At this point the time can be prolonged, proceeding as

described above, or the timer can be deactivated by pressing button (the time of day will be

shown on the display).

RECIPES

Thanks to “Sixth sense” technology, the oven offers 30 pre-set recipes with ideal cooking temperatures.

Simply follow the recipe as regards ingredients and the method of preparation. Then, proceed as follows:

1. Select “RECIPES” using buttons and confirm with .

2. Select the dish to be cooked from the proposed list.

3. Confirm the selected dish using button .

4. Select the desired recipe using buttons .

5. Confirm by pressing button : the display shows the approximate cooking time.

6. Put the food in the oven and press button . The display indicates which shelf food should be placed

on.

7. Press button to start cooking. To delay the start of cooking, see the relevant paragraph.

N.B.:some dishes must be turned or stirred half way through cooking: the oven will emit an acoustic

signal and the display will indicate what action is required.

The initial cooking time displayed is merely for guidance: it can be prolonged automatically during

cooking.

Shortly before cooking time finishes, the oven prompts you to check that the food is cooked to your

satisfaction. If it is not, extra time can then be added manually using the buttons .

SHORTCUTS

1. Press button : the display shows the 10 most used functions.

2. To scroll down the list, use buttons .

3. Press to select the desired function.

4. To change the settings of the selected function, proceed as shown in the previous paragraphs.

Press to set Timer, ✓ to Start

00 : 00 : 00

(HH) (MM) (SS)

Press to set Timer, ✓ to Start

01 : 10 : 00

(HH) (MM) (SS)

Timer

01 : 09 : 00

Fully automatic 6th Sense recipes

Traditional

Settings

Recipes

6th Sense: Press ✓ to view recipes

Vegetables

Fish

Poultry

6th Sense: See cookbook for description

Chicken Breasts

Roast Chicken

CONTROL

Automatic

COOK TIME

END TIME

Roast Chicken

19:45

- 00:45

CONTROL

Automatic

COOK TIME

END TIME

Cooking

19:45

- 00:44

Insert food on level 3

Press when done

Please turn food

Cooking nearly nished

Please check on food

Cooking Finished at 19:45

Press to Prolong Cooking

Your most used cooking functions

Chicken Breasts

Lasagna

Pizza

EN15

SETTINGS

1. To change some display settings, select “SETTINGS” from the main menu using buttons .

2. Confirm by pressing : the display shows which settings can be changed (language, volume of

acoustic signal, display brightness, time, energy saving function).

3. Select the setting you wish to change using buttons .

4. Press button to confirm.

5. Follow the instructions of the display to change the settings.

6. Press ; a message appears on the display confirming your selection.

N.B.:When the oven is switched off, if the ECOMODE (Energy saving) function is selected (ON), the display

switches off after a few seconds, showing the clock. To view information on the display and switch the light

on again, just press any of the buttons or turn one of the knobs. During a cooking function if the ECOMODE

is activated the cavity lamp will be switched off after 1 minute of cooking and reactivated for each user

interaction. If, on the other hand, the function is not selected (OFF), after a few minutes the display is merely

dimmed.

KEY-LOCK

This function can be used to lock the control panel buttons.

To activate it, press and at the same time for at least 3 seconds. If activated, the functions of the

buttons are locked and the display shows a message and the symbol . This function can also be activated

during cooking. To deactivate it, repeat the above procedure. When the key-lock function is activated, the

oven can be switched off using button .

EN16

FUNCTION DESCRIPTION TABLE

MAIN MENU

SETTINGS

Setting the display (language, time, brightness, volume of acoustic signal,

energy saving function).

RECIPES

Selecting 30 different pre-set recipes (see enclosed recipe booklet).

The oven automatically sets the optimum cooking temperature, function

and time. It is important to follow the instructions given in the recipe book

regarding preparation, accessories and which oven shelf to use.

TRADITIONAL See TRADITIONAL FUNCTIONS.

SPECIALS See SPECIAL FUNCTIONS.

TRADITIONAL FUNCTIONS

FAST PREHEATING To preheat the oven rapidly.

CONVENTIONAL

To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza,

savoury pies and sweets with liquid fillings, use the 1st or 2nd shelf.

The oven does not have to be preheated.

GRILL

To grill steak, kebabs and sausages; to cook vegetables au gratin and toast

bread. Place food on the 4th or 5th shelf. When grilling meat, use the drip

tray to collect the cooking juices. Position it on the 3rd/4th shelf, adding

approx. half a litre of water. The oven does not have to be preheated.

During cooking the oven door must remain closed.

TURBO GRILL

To roast large joints of meat (legs, roast beef, chickens). Position the food

on the middle shelves. Use the drip tray to collect the cooking juices.

Position it on the 1st/2nd shelf, adding approx. half a litre of water.

The oven does not have to be preheated. During cooking the oven door

must remain closed. With this function you can also use the turnspit, if

provided.

FORCED AIR

To cook a variety of food requiring the same cooking temperature on

several shelves (maximum three) at the same time (e.g.: fish, vegetables,

cakes). This function can be used to cook different foods without odours

being transferred from one food to another. Use the 2nd shelf to cook on

one shelf only, the 1st and 4th to cook on two shelves, and the 1st, 3rd and

5th to cook on three shelves. The oven does not have to be preheated.

CONVECTION BAKE

To cook meat and pies with liquid filling (savoury or sweet) on single shelf.

Use 3rd shelf. The oven does not have to be preheated.

EN17

SPECIAL

DEFROST

To speed up defrosting of food. Place food on the middle shelf. Leave food

in its packaging in order to prevent it from drying out on the outside.

KEEP WARM

For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).

Place food on the middle shelf. The function will not activate if the

temperature in the oven is above 65°C.

RISING

For optimal rising of sweet or savoury dough. To safeguard the quality of

proving, the function will not activate if the temperature in the oven is

above 40°C. Place the dough on the 2nd shelf. The oven does not have

to be preheated.

CONVENIENCE

Cooking ready meals kept at room temperature or from refrigerated

cabinets (biscuits, liquid cake mixtures, muffins, first courses and bakery

products). This function gently cooks all food quickly; it can also be used

to reheat cooked food. Follow the instructions on the food packaging.

The oven does not have to be preheated.

MAXI COOKING

To cook large joints of meat (above 2.5 kg). Use the 1st or 2nd shelves,

depending on the size of the joint. The oven does not have to be

preheated. It is advisable to turn the meat over during cooking, to obtain

even browning on both sides. It is preferable to baste the meat every now

and again so that it does not become too dry.

FROZEN

FOOD

Lasagne

The function automatically selects the ideal cooking temperature and

mode for 5 different types of ready frozen food. Use the 2nd or 3rd shelf.

The oven does not have to be preheated.

Pizza

Strudel

French

Fries

Bread

Custom

The temperature can be set from 50 to 250°C to cook other types of

product.

ECO FORCED AIR

To cook stuffed roasts and meat in pieces on one shelf. This function uses

discontinuous, delicate fan assistance, which prevents excessive drying of

foods. In this ECO function the light remains off during cooking and can be

temporarily switched on again by pressing the confirm button. In order to

maximize energy efficiency, it is advisable not to open the door during

cooking. It is advisable to use 3rd level. The oven does not have to be

preheated.

EN18

COOKING TABLES

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and notes

Leavened cakes

- 2/3 160-180 30-90 Cake tin on rack

- 1-4 160-180 30-90

Level 4: cake tin on rack

Level 1: cake tin on rack

Filled pies

(cheesecake, strudel,

apple pie)

- 3 160-200 35-90

Drip-tray / baking tray or

cake tin on rack

- 1-4 160-200 40-90

Level 4: cake tin on rack

Level 1: cake tin on rack

Biscuits/Tartlets

- 3 170-180 20-45 Drip-tray or baking tray

- 1-4 160-170 20-45

Level 4: rack

Level 1: drip-tray or baking

tray

- 1-3-5 160-170 20-45*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or baking

tray

Choux buns

- 3 180-200 30-40 Drip-tray or baking tray

- 1-4 180-190 35-45

Level 4: pan on rack

Level 1: drip-tray or baking

tray

- 1-3-5 180-190 35-45*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or baking

tray

Meringues

- 3 90 110-150 Drip-tray or baking tray

- 1-4 90 140-160

Level 4: pan on rack

Level 1: drip-tray or baking

tray

- 1-3-5 90 140-160*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or baking

tray

Bread / Pizza /

Focaccia

-1/2190-250 15-50 Drip-tray or baking tray

- 1-4 190-250 20-50

Level 4: pan on rack

Level 1: drip-tray or baking

tray

- 1-3-5 190-250 25-50*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or baking

tray

EN19

Savoury pies

(vegetable pie,

quiche lorraine)

- 2/3 180-190 40-55 Cake tin on rack

- 1-4 180-190 45-70

Level 4: cake tin on rack

Level 1: cake tin on rack

- 1-3-5 180-190 45-70*

Level 5: cake tin on rack

Level 3: cake tin on rack

Level 1: drip-tray or baking

tray + cake tin

Vols-au-vent / Puff

pastry savouries

- 3 190-200 20-30 Drip-tray or baking tray

- 1-4 180-190 20-40

Level 4: pan on rack

Level 1: drip-tray or baking

tray

- 1-3-5 180-190 20-40*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or baking

tray

Lasagna / Baked

pasta / Cannelloni /

Flans

- 3 190-200 45-65 Drip-tray or pan on rack

Lamb / Veal / Beef /

Pork 1 Kg

- 3 190-200 80-110 Drip-tray or pan on rack

Chicken / Rabbit /

Duck 1 Kg

- 3 200-230 50-100 Drip-tray or pan on rack

Turkey / Goose 3 Kg - 2 190-200 80-130 Drip-tray or pan on rack

Baked fish / en papil-

lote (fillet, whole)

- 3 180-200 40-60 Drip-tray or pan on rack

Stuffed vegetables

(tomatoes, courget-

tes, aubergines)

- 2 180-200 50-60 Pan on rack

Toas t - 5 High 3-6 Rack

Fish fillets / steaks - 4 Medium 20-30

Level 4: rack (turn food

halfway through cooking)

Level 3: drip-tray with water

Sausages / Kebabs /

Spare ribs /

Hamburgers

- 5

Medium-

High

15-30

Level 5: rack (turn food

halfway through cooking)

Level 4: drip-tray with water

Roast chicken

1-1.3 Kg

- 2 Medium 55-70

Level 2: rack (turn food two

thirds of the way through

cooking)

Level 1: drip-tray with water

- 2 High 60-80

Level 2: turnspit (if present)

Level 1: drip-tray with water

Roast beef rare 1 Kg - 3 Medium 35-50

Pan on rack (turn food two

thirds of the way through

cooking if necessary)

Leg of lamb / Shanks - 3 Medium 60-90

Drip-tray or pan on rack (turn

food two thirds of the way

through cooking if

necessary)

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and notes

EN20

* Cooking time is approximate. Food can be removed from the oven at different times depending on

personal preference.

Baked potatoes - 3 Medium 45-55

Drip-tray or baking tray (turn

food two thirds of the way

through cooking if

necessary)

Vegetables au gratin - 3 High 10-25 Drip-tray or pan on rack

Lasagna & Meat - 1-4 200 50-100*

Level 4: pan on rack

Level 1: drip-tray or pan on

rack

Meat & Potatoes - 1-4 200 45-100*

Level 4: pan on rack

Level 1: drip-tray or pan on

rack

Fish & Vegetables - 1-4 180 30-50*

Level 4: pan on rack

Level 1: drip-tray or pan on

rack

Complete meal:

Tart (Level 5) /

Lasagna (Level 3) /

Meat (Level 1)

- 1-3-5 190 40-120*

Level 5: pan on rack

Level 3: pan on rack

Level 1: drip-tray or pan on

rack

Frozen pizza

- 3 Auto 10-15

Level 3: drip-tray / baking

tray or rack

- 1-4 Auto 15-20

Level 4: pan on rack

Level 1: drip-tray or baking

tray

- 1-2-4 Auto 20-30

Level 4: baking tray

Level 2: pan on rack

Level 1: drip-tray or baking

tray

- 1-2-3-4 Auto 20-30

Level 4: baking tray

Level 3: pan on rack

Level 2: pan on rack

Level 1: drip-tray / baking

tray

Filled roast meats - 3 200 80-120* Drip-tray or pan on rack

Meat cuts (rabbit,

chicken, lamb)

- 3 200 50-100* Drip-tray or pan on rack

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and notes

Strona jest ładowana ...

Whirlpool AKZM 656/IX/01 instrukcja

Whirlpool AKZM 656/IX/01 instrukcja

w innych językach

Powiązane dokumenty