Sony KP-41PX2 Instrukcja obsługi

Kategoria
Telewizory LCD
Typ
Instrukcja obsługi
R
4-094-048-
11
(1)
Instruction Manual
KP-41PX2
©2003 by Sony Corporation
GB
Инструкции за експлоатация
BG
Kezelési útmutató
CZ
Návod k obsluze
HU
Instrukcja obsługi
PL
Инструкция пo эксплyатации
RU
100 Hz
Projection TV
3
GB
Introduction
Thank you for choosing this Sony 100 Hz Projection TV.
Before operating the projection TV, please read this manual thoroughly and retain it for future reference.
• Symbols used in the manual:
Important information.
Information on a feature.
1,2...
Sequence of instructions.
Shaded buttons on the remote control show you the buttons you have
to press to follow the sequence of the instructions.
Informs you of the result of the instructions.
Table of Contents
Introduction..........................................................................................................................................................................................................3
Safety Information...............................................................................................................................................................................................4
Overview
Overview of Remote Control Buttons ..............................................................................................................................................................5
Overview of TV Buttons ....................................................................................................................................................................................6
Installation
Connecting the Aerial and VCR .......................................................................................................................................................................7
Inserting Batteries into the Remote Control ....................................................................................................................................................7
First Time Operation
Switching On the TV and Automatically Tuning ..........................................................................................................................................8
Adjusting Colour Registration (Convergence)..............................................................................................................................................10
Menu system
Introducing and Using the Menu System......................................................................................................................................................10
On Screen Display Menus Guide ....................................................................................................................................................................11
Menu Guide:
Picture Adjustment........................................................................................................................................................................................12
Sound Adjustment .........................................................................................................................................................................................12
Sleep Timer .....................................................................................................................................................................................................13
AV3 Output.....................................................................................................................................................................................................13
PIP Input..........................................................................................................................................................................................................13
PIP Position.....................................................................................................................................................................................................14
Language/Country........................................................................................................................................................................................14
Auto Tuning....................................................................................................................................................................................................14
Programme Sorting........................................................................................................................................................................................14
Programme Labels .........................................................................................................................................................................................15
AV Preset.........................................................................................................................................................................................................15
Manual Programme Preset ...........................................................................................................................................................................16
RGB Centring..................................................................................................................................................................................................17
Teletext
..................................................................................................................................................................................................................... 18
NexTView
................................................................................................................................................................................................................ 19
Additional Information
Connecting Optional Equipment ....................................................................................................................................................................20
Using Optional Equipment ..............................................................................................................................................................................21
SmartLink ...........................................................................................................................................................................................................22
Remote Control Configuration for VCR/DVD.............................................................................................................................................23
Optimum Viewing Area ...................................................................................................................................................................................24
Specifications......................................................................................................................................................................................................25
Troubleshooting.................................................................................................................................................................................................26
Table of Contents
4
Safety Information
Additional Safety Information
After transporting the projection TV directly from a cold to a warm location, or if the room temperature has changed suddenly,
pictures may be blurred or show poor colour over portions of the picture. This is because moisture has condensed on the mirrors
or lenses inside the projection TV. Let the moisture evaporate before using the projection TV.
To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed
down from the ceiling.
Displaying a still picture for long periods of time, for instance, when operating a video game or personal computer and viewing
programme in 16:9 mode, may damage the picture tube. To avoid this, keep the picture contrast level low.
Avoid touching the screen, and take care not to scratch the surface with hard objects.
Do not open the cabinet and the rear cover of
the TV. Refer to qualified service personnel
only.
To prevent fire or shock hazard, do not
expose the TV to rain or moisture.
For your own safety, do not touch any part
of the TV, power lead or aerial lead during
lightning storms.
Do not cover the ventilation openings of the
TV For ventilation, leave a space of at least
10cm all around the set.
To prevent fire, keep inflammable objects or
naked lights (eg candles) away from the TV.
Clean the screen and cabineet with a soft, lightly
dampened cloth. Do not use any type of
abrasive pad, alkaline cleaner, scouring powder
or solvent, such as alcohol or benzine, or
antistatic spray. As safety precaution, unplug
the TV before cleaning it.
Pull out the power lead by the plug. Do not
pull on the power lead itself.
Take care not to place heavy objects on the
power lead as this could result in damage.
We recommend you wind any excess lead
around the holders provided on the rear of
the TV.
Place the TV on a secure stable stand. Do not
allow children to climb on to it. Do not place
the TV on its side or face up.
Do not cover the ventilation openings of the
TV with items such as curtains or
newspapers etc.
Never push objects of any kind into the set as
this could result in a fire or electric shock.
Never spill liquid of any kind on the set. If
any liquid or solid object does fall into the
cabinet, do not operate the TV. Have it
checked immediately by qualified personnel.
For environmental and safety reasons, it is
recommended that the TV set is not left in
standby mode when not in use. Disconnect
from the mains.
This set is to operate on a 220-240V AC
supply only. Take care not to connect too
many appliances to the same power socket
as this could result in fire or electric shock.
Safety Information
Unplug the power lead before moving the
TV. Avoid uneven surfaces, quick steps or
excessive force. If the set has been dropped
or damaged, have it checked immediately
by qualified service personnel.
Never place the TV in hot, humid or
excessively dusty places. Do not install the
TV where it may be exposed to mechanical
vibrations.
5
GB
Checking the Accessories Supplied
Overview
Overview of Remote Control Buttons
1
qf
qs
qd
qa
2
3
4
5
6
7
8
9
0
qg
qh
wd
ws
wa
w;
ql
qk
qj
1
To Temporarily Switch Off TV:
Press this button to temporarily switch off TV (the standby indicator on the TV lights up). Press
again to switch on TV from standby mode.
To save energy we recommend switching off completely when TV is not in use.
After 15 minutes without a signal and without any button being pressed, the TV switches
automatically into standby mode.
2
VCR or DVD on/off:
Press this button to switch your VCR or DVD on or off.
3
Media Selector:
With this remote control you can operate not only this TV but also the main functions of your VCR
or DVD. Switch on the device you want to operate and next press this button repeatedly to select
the VCR, TV or DVD. A green light will be momentarily lit to indicate the chosen function.
Before the first time you want to control a DVD or VCR by using this remote control, you have
to set it up depending on the brand of the device to be used. For more details, refer to the
chapter “Remote Control Configuration for VCR or DVD” on page 23.
4
Selecting input source:
Press this button repeatedly until the desired input symbol of the
source appears on the TV screen.
5
Selecting channels:
If Media Selector is switched to TV or VCR, press this button to select channels.
For double-digit programme numbers, enter the second digit within 2.5 seconds.
6
a) If Media Selector is switched to TV:
Press this button to watch the last channel selected (the last channel watched for at least 5
seconds).
b) If Media Selector is switched to VCR:
For Sony’s VCR double-digit programme numbers, e.g. 23, press -/- - first and then the buttons
2 and 3.
7
Selecting screen format:
Press this button repeatedly to change the format of the screen. 4:3
for a conventional picture or 16:9 for a imitation of wide screen.
8
This button only works in Teletext mode.
9
Selecting Teletext:
Press this button to switch on teletext.
0
Joystick:
a) If Media Selector is switched to TV:
• When MENU is switched on, use these buttons to operate the menu system. For details refer
to “Introducing and Using the Menu System” on page 10.
• When MENU is switched off, press OK to show a channel overview. Then press or to
select the channel and then press again the OK button to watch the selected channel.
b) If Media Selector is switched to VCR or DVD:
Using these buttons you can control the main functions of your VCR or DVD.
qa
Displaying the menu system:
Press this button to display the menu on the TV screen. Press again to remove the menu display
from the TV screen.
qs
Selecting channels:
Press these buttons to select the next or previous broadcast channel.
qd
NexTView:
For more details refer to chapter “NexTView” on page 19.
qf
Adjusting TV volume:
Press these buttons to adjust the volume of the TV.
qg
Recording button:
If Media Selector is switched to VCR, press this button to record programmes.
qh
Selecting TV mode:
Press this button to switch off PIP, teletext or video input.
qj
Selecting Picture mode:
Press this button repeatedly to change the picture mode.
qk
Selecting Sound effect:
Press this button repeatedly to change the sound effect.
ql
Displaying on Screen information:
Press this button to display all on-screen indications. Press again to cancel.
w;
Freezing the picture:
Press this button to freeze the picture. The screen is divided into two screens. On the left with the normal
picture, on the right the picture is freezed. Press this button again to return to the normal picture.
wa
Swapping screens:
Whilst you are in “PIP” mode, press this button to swap the two screens.
ws
PIP (Picture in Picture):
Press this button to watch another source in a small picture (PIP) within the main TV picture. Press again
to cancel. To select the source you want to watch, refer to the chapter “PIP Input” on page 13.
wd
Muting the Sound:
Press this button to mute TV sound. Press again to restore the sound.
Besides TV functions, all coloured buttons as well as green symbols are also used for Teletext operation. For more details,
please refer to the chapter “Teletext” on page 18.
6
Overview
Overview of Projection TV Buttons
On/Off
Switch
Video
Input
jack
S video
Input
jack
Audio
Input
jacks
Headphones
jack
1
Auto Convergence
Button:
Press this button to adjust
the colour registration.
For more details, please
refer to the chapter
“Adjusting Colour
Registration
(Convergence)” on page
10.
or
2
Auto Start Up Button:
Press and hold this
button for approximately
2 seconds to start the auto
start up sequence.
For more details, please
refer to the chapter
“Switching On the
Projection TV and
Automatically Tuning”
on page 8.
Standby
indicator
Programme
Up or Down
Buttons
(Select TV
channels)
Volume
control
buttons
Push up the flap on the front of the TV
to reveal the front control panel.
Selecting
Input
source
7
GB
Installation
Connecting the Aerial and VCR
Connecting cables are not supplied.
Inserting Batteries into the Remote Control
Make sure you insert the supplied batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.
or
For more details of VCR connection, please refer to the section “Additional information
when connecting equipment” on page 21.
VCR
OUT IN
Scart lead is optional.
8
Switching On the Projection TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose the language
of the menu screen, 2) choose the country in which you wish to operate the TV, 3) search and store all available channels (TV
Broadcast) and 4) change the order in which the channels (TV Broadcast) appear on the screen.
However, if you need to change any of these settings at a later date, you can do that by selecting the appropriate option in
the (Set Up menu) or by pressing the Auto Start Up Button / on the TV set.
First Time Operation
1 Connect the Projection TV plug to the mains socket (220-240V AC, 50Hz)
The first time that the TV set is connected, it is usually turned on. If the TV is off, press
the on/off button on the TV set to turn on the TV.
The first time you switch on the TV, a Language menu displays automatically on the
TV screen.
2 Press the or button on the remote control to select the language, then press the
OK button to confirm your selection. From now on all the menus will appear in the
selected language.
3 The Country menu appears automatically on the TV screen. Press the or button
to select the country in which you will operate the TV set, then press the OK
button to confirm your selection.
• If the country in which you want to use the TV se does not appear in the list,
select “-” instead of a country.
• To avoid wrong teletext characters for cyrillic languages we recommend
selecting Russia country if your own country does not appear in the list.
4 The Auto Tuning menu appears on the screen. Press the OK button to select Yes.
5 The projection TV starts to automatically search and store all available broadcast
channels for you.
This procedure could take some minutes. Please be patient and do not press
any buttons, otherwise automatic tuning will not be completed.
In some countries the TV Broadcaster installs the channels automatically (ACI
system). In this case, the TV Broadcaster sends a menu in which you can select
your city by pressing the or button and OK to store the channels.
If no channels were found during the auto tuning process then a new menu
appears automatically on the screen asking you to connect the aerial. Please
connect the aerial (see page 7) and press OK. The auto tuning process will start
again.
Language
English
Norge
Français
Italiano
Nederlands
Select Language: Confirm: OK
Country
Sverige
Norge
-
Italia
Schweiz/Suisse/Svizzera
Select Language: Confirm: OK
continued...
Programme:
Channel:
System
Searching...
1
C 01
B/G
Auto Tuning
Do you want to start
automatic tuning?
Yes
No
No channel found
Please connect aerial
Confirm
Language
English
Norge
Français
Italiano
Nederlands
Select Language: Confirm: OK
Language
English
Norge
Français
Italiano
Nederlands
Select Language: Confirm: OK
9
GB
6 After all available channels are captured and stored, the Programme Sorting menu
automatically appears on the screen enabling you to change the order in which the
channels appear on the screen.
a) If you wish to keep the broadcast channels in the tuned order, go to step 7.
b) If you wish to store the channels in a different order:
1 Press the or button to select the programme number with the channel (TV
Broadcast) you wish to rearrange, then press the button.
2 Press the or button to select the new programme number position for your
selected channel (TV Broadcast), then press OK.
3 Repeat steps b)1 and b)2 if you wish to change the order of the other channels.
7 Press the MENU button to remove the menu from the screen.
Programme Sorting
Programme:
01 TVE2 41 TVE
02 TVE
03 ANT3
04 TELE5
05 C+
06 C44
Select new position Move: OK
MENU
Programme Sorting
Programme:
01 TVE2
02 TVE
03 ANT3
04 TELE5
05 C+
06 C44
Select Channel Confirm:
Your projection TV is now ready for use.
First Time Operation
10
Auto converge the Red, Green, and
Blue Lines
1 Push up the flap on the front of the projection TV to reveal the front
control panel.
2 Press / button.
The Auto Convergence function works for about 10 seconds. When the white
cross disappears from the screen, your projection TV is ready for use.
The Auto Convergence function does not work when:
• no signal is input.
• the input signal is weak.
the screen is exposed to spotlights or direct sunlight.
• you watch the teletext broadcast.
you watch NexTView.
Adjusting Colour Registration (Convergence)
Due to the earth’s magnetism, the picture might become undefined and you could see different colours on the outlines of
the images.
In that case, proceed as follows:
1 Press the MENU button to switch the first level menu on.
2 • To highlight the desired menu or option, press or .
• To enter the selected menu or option, press .
• To return to the last menu or option, press .
• To alter the settings of your selected option, press //or.
• To confirm and store your selection, press OK.
3 Press the MENU button to remove the menu from the screen.
Introducing and Using the Menu system
Your projection TV uses an on-screen menu system to guide you through the operations. Use the following buttons on the
Remote Control to operate the menu system:
First Time Operation - Menu System
MENU
MENU
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
11
GB
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Sound Adjustment
Select: Enter Menu:
Effect
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
TV Speakers
Natural
Off
Stereo
On
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter Menu:
Off
AUTO
AV1
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
On Screen display Menus Guide
Refer to the section "Picture Adjustment”, on page 12.
Refer to the section "Sound Adjustment”, on page 12.
Refer to the section "RGB Centring"
on page 17.
Menu System
Refer to the section "Sleep Timer" on page 13.
Refer to the section "AV3 Output" on page 13.
Refer to the section "PIP Input" on page 13.
Refer to the section "PIP Position" on page 14.
Refer to the section "Language/Country" on page 14.
Refer to the section "Auto Tuning" on page 14.
Refer to the section "Programme Sorting" on page 14.
Refer to the section "Programme Labels" on page 15.
Refer to the section "AV Preset" on page 15.
Refer to the section "Manual Programme Preset" on page 16.
Sound Adjustment
Select: Enter:
Effect
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
TV Speakers
Natural
Off
Stereo
On
Picture Adjustment
Select: Enter:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter:
Off
AUTO
AV1
Select: Enter:
Features
Off
AUTO
AV1
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter:
Features
Off
AUTO
AV1
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter:
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Off
AUTO
AV1
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Start Auto Tuning:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Detail Set Up
Select:
RGB Centring
0
Set Up
Select:
Enter Menu:
Set Up
Select:
Enter Menu:
Set Up
Select:
Enter Menu:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
12
Menu Guide
Menu System
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to alter the picture
adjustments.
To do this: after selecting the item you want to alter press , then
press repeatedly / / or to adjust it and finally press OK to
store the new adjustment.
Level 1 Level 2 Level 3 / Function
This menu also allows you to customise the picture mode based on the programme you are watching:
Picture Mode Live (for live broadcast programmes, DVD and Digital Set Top Box receivers).
Personal (for individual settings).
Movie (for films).
Brightness, Colour and Sharpness can only be altered if “Personal” mode is selected.
Hue is only available for NTSC colour signal (e.g: USA video tapes).
Select Reset and press OK to reset the picture to the factory preset levels.
The Noise Reduction option is set to AUTO to automatically reduce the picture noise visible in the broadcast signal. To cancel this
function, select “Off” instead of “AUTO”.
SOUND ADJUSTMENT
The “Sound Adjustment” menu allows you to alter the sound
adjustments.
To do this: after selecting the item you want to alter, press . Then
press repeatedly / / or to adjust it and finally press OK to
store the new adjustment.
Effect Natural: Enhances clarity, detail and presence of sound by using “BBE High Definition Sound system”*.
Dynamic: “BBE High Definition Sound system”* intensifies clarity and presence of sound for better
intelligibility and musical realism.
Dolby**V: Dolby Virtual, simulates the sound effect of “Dolby Surround Pro Logic”.
Off: Flat response.
Treble Less More
Bass Less More
Balance Left Right
Reset Resets the sound to the factory preset levels.
Dual Sound For a stereo broadcast:
Mono.
Stereo.
For a bilingual broadcast:
Mono (for mono channel if available).
A (for channel 1).
B (for channel 2).
Auto Volume Off: volume level changes according to the broadcast signal.
On: volume level of the channels will stay the same, independent of the broadcast signal
(e.g. in the case of advertisements).
TV Speakers On: to listen to the TV from the set speakers.
Off: to listen to the TV from an external amplifier connected to the audio outputs on the rear of the projection
TV set.
If you are listening to the TV through headphones, the “Effect” option will automatically be switched to “Off”.
If you select “Dolby Virtual” on the “Effect” option, the “Auto Volume” option will automatically be switched to “Off” and vice versa.
* The “BBE High Definition Sound system” is manufactured by Sony Corporation under license from BBE Sound, Inc. It is covered by
U.S. Patent No. 4,638,258 and No. 4,482,866. The word “BBE” and BBE Symbol are trademarks of BBE Sound, Inc.
** This TV has been designed to create the “Dolby Surround” sound effect by simulating the sound of four speakers with two speakers,
when the broadcast audio signal is Dolby Surround encoded. The sound effect can also be improved by connecting a suitable external
amplifier (for details refer to “Connecting to external audio Equipment” on page 21).
** Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
K
Picture Adjustment
Select: Enter:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
continued...
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Sound Adjustment
Select: Enter Menu:
Effect
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
TV Speakers
Natural
Off
Stereo
On
Sound Adjustment
Select: Enter:
Effect
Treble
Bass
Balance
Reset
Dual Sound
Auto Volume
TV Speakers
Natural
Off
Stereo
On
13
GB
Menu System
Level 1 Level 2 Level 3 / Function
SLEEP TIMER
The “Sleep Timer” option in the “Features” menu allows you to
select a time period for the TV to switch itself automatically into the
standby mode.
To do this: after selecting the option press , then press or to
set the time period delay (max. of 4 hours).
While watching the TV, you can press the button on the remote control to display the time remaining.
One minute before the projection TV switches itself into standby mode, the time remaining is displayed on the TV screen automatically.
AV3 OUTPUT
The “AV3 Output” option in the “Features” menu allows you to
select the source to be output from the Scart connector 3/ 3 so
that you can record from this Scart any signal coming from the
projection TV or from an external equipment connected to the Scart
connectors 1/ 1 or 2/ 2 or front connectors 4 or
4 and 4.
If your VCR supports Smartlink, this procedure is not
necessary.
To do this: after selecting the option, press . Then press or to
select the desired output signal: TV, AV1, AV2, AV4, YC4 or
AUTO.
If you select “AUTO”, the output signal will always be the same one that is displayed on the screen.
If you have connected a decoder to the Scart 3/ 3 or to a VCR connected to this Scart, please remember to change back
the “AV3 Output” to “AUTO” or “TV” for correct unscrambling.
PIP INPUT
The “PIP Input” option in the “Features” menu allows you to select
the source you want to watch in the “PIP” screen.
To do this: after selecting the option, press . Then press repeatedly
or to select the desired source AV1, AV2, AV3, AV4 or TV.
Finally press OK to store.
To watch the “PIP” screen with the selected source, press the
/ button on the remote control.
You can swap the screens by pressing the / button on the
remote control.
S
S
S
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter Menu:
Off
AUTO
AV1
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter:
Off
AUTO
AV1
Select: Enter:
Features
Off
AUTO
AV1
Sleep Timer
AV3 Output
PIP Input
PIP Position
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter Menu:
Off
AUTO
AV1
continued...
B
A
A
BB
B
A
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter Menu:
Off
AUTO
AV1
Select: Enter:
Features
Off
AUTO
AV1
Sleep Timer
AV3 Output
PIP Input
PIP Position
14
Menu System
Level 1 Level 2 Level 3 / Function
PIP POSITION
The “PIP Position” option in the “Features” menu allows you to
change the position of the “PIP” screen within the main screen.
To do this: after selecting the option press , , or to select
the desired position. Finally press OK to store.
LANGUAGE/COUNTRY
The “Language/Country” option in the “Set Up” menu allows you
to select the language that the menus are displayed in. It also allows
you to select the country in which you wish to operate the
projection TV set.
To do this: after selecting the option, press and then proceed in
the same way as in steps 2 and 3 of the section “Switching On the
Projection TV and Automatically Tuning” on page 8.
AUTO TUNING
The “Auto Tuning” option in the “Set Up” menu allows you to
automatically search for and store all available TV channels.
To do this: after selecting the option, press and then proceed in
the same way as in the steps 4 and 5 of the section “Switching On
the Projection TV and Automatically Tuning” on page 8.
PROGRAMME SORTING
The “Programme Sorting” option in the “Set Up” menu allows you
to change the order in which the channels (TV Broadcast) appear on
the screen.
To do this: after selecting the option, press and then proceed in
the same way as in step 6 b) of the section “Switching On the
Projection TV and Automatically Tuning” on page 9.
Select: Enter:
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Off
AUTO
AV1
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Features
Sleep Timer
AV3 Output
PIP Input
PIP Position
Select: Enter Menu:
Off
AUTO
AV1
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
continued...
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
Start Auto Tuning:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
15
GB
Menu System
Level 1 Level 2 Level 3 / Function
PROGRAMME LABELS
The “Programme Labels” option in the “Set Up” menu allows you
to name a channel using up to five characters (letters or numbers).
To do this:
1 After selecting the option, press , then press or to select the
programme number with the channel you wish to name.
2 Press . With the first element of the Label column highlighted,
press or to select a letter or number (select “-“ for a blank),
then press to confirm this character. Select the other four
characters in the same way. Finally press OK to store.
AV PRESET
The “AV Preset” option in the “Set Up” menu allows you to
designate a name to the external equipment you have connected to
the input sockets of this projection TV.
To do this:
1 After selecting the option, press , then press or to select the
input source you wish to name (AV1, AV2 and AV3 are for the
rear Scarts and AV4 for front connectors). Then press .
2 A label automatically appears in the label column:
a) If you want to use one of the 6 predefined label (CABLE,
GAME, CAM, DVD, VIDEO or SAT), press or to select
the desired label and finally press OK to store.
b) If you want to set a different label, select Edit and press .
Then with the first element highlighted, press or to
select a letter, number or “-“ for a blank, then press to
confirm this character. Select the other four characters in the
same way and finally press OK to store.
continued...
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
16
Menu System
Level 1 Level 2 Level 3 / Function
MANUAL PROGRAMME PRESET
The “Manual Programme Preset” option in the “Set Up” menu
allows you to:
a) Preset channels or the VCR channel one by one to the programme order of your choice. To do this:
1 After selecting the ”Manual Programme Preset” option, press then with Programme option highlighted press .
Press or to select which programme number you want to preset the channel on (for VCR, select programme number
“0”). Then press .
2 The following option is only available depending on the country you have selected in the “Language/Country”
menu.
After selecting the System option, press . Then press or to select the TV Broadcast system (B/G for western
European countries, D/K for eastern European countries, L for France or I for United Kingdom). Then press .
3 After selecting the Channel option, press . Then press the number buttons to enter directly the channel number of the
TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press or to search for it. When
you have tuned the desired channel, press OK twice to store.
Repeat all the above steps to tune and store more channels.
b) Label a channel using up to five characters.
To do this: highlighting the Programme option, press the PROG +/- button to select the programme number with the channel
you wish to name. When the programme you want to name appears on the screen, select the Label option and press . Next
press or to select a letter, number or “-“ for a blank. Press to confirm this character. Select the other four characters in
the same way. After selecting all the characters, press OK twice to store.
c) Fine tune the broadcast reception. Normally the automatic fine tuning (AFT) will give the best possible picture, however you
can manually fine tune the TV to obtain a better picture reception in case the picture is distorted.
To do this: while watching the channel (TV Broadcast) you wish to fine tune, select the AFT option and press . Next press
or to adjust the fine tuning between -15 and +15. Finally press OK twice to store.
d) Skip any unwanted programme numbers when they are selected with the PROG +/- buttons.
To do this: highlighting the Programme option, press the PROG +/- button to select the programme number you want to skip.
When the programme you want to skip appears on the screen, select the Skip option and press . Next press or to select
Yes. Finally press OK twice to confirm and store.
To cancel this function afterwards, select “No” instead of “Yes” in the step above.
e) View and record correctly scrambled channels when using a decoder connected directly to Scart 3/ 3 or through a VCR.
This option is only available depending on the country you have selected in the “Language/Country” menu.
To do this: select the Decoder option and press . Next press or to select On. Finally press OK twice to confirm and store.
To cancel this function afterwards, select “Off” instead of “On” in the step above.
S
continued...
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Auto Tuning
Programme Sorting
Select NexTView
AV Preset
Manual Set Up
Select:
Enter Menu:
Set Up
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Select:
Enter Menu:
Enter:
Set Up
Select:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
17
GB
Menu System
Level 1 Level 2 Level 3 / Function
RGB CENTRING
When connecting an RGB source, such as a “PlayStation”, you may
need to readjust the horizontal position of the picture. If this is the
case, you can adjust it through the “RGB Centring” option in the
“Detail Set Up”.
To do this: while watching an RGB source select the “RGB Centring”
option and press . Then press or to adjust the centre of the
picture between –10 and +10. Finally press OK to confirm and store.
Picture Adjustment
Select: Enter Menu:
Picture Mode
Contrast
Brightness
Colour
Sharpness
Reset
Noise Reduction
Personal
AUTO
Enter:
Detail Set Up
Select:
RGB Centring
0
Set Up
Select:
Enter Menu:
Set Up
Select:
Enter Menu:
Set Up
Select:
Enter Menu:
Language/Country
Auto Tuning
Programme Sorting
Programme Labels
AV Preset
Manual Programme Preset
Detail Set Up
18
Teletext
Teletext is an information service transmitted by most TV stations. The index page of the teletext service (usually page 100)
gives you information on how to use the service. To operate teletext, use the remote control buttons as indicated below.
Teletext errors may occur if you use a channel (TV Broadcast) with a weak signal.
After 5 minutes viewing the same teletext page and without any button being pressed, the brightness level of the picture
automatically decreases notoriously to avoid any damage to the picture tube. Press any button of the remote control to
reset the brightness level.
To switch on Teletext :
After selecting the TV channel which carries the teletext service you
wish to view, press .
To select a Teletext page:
Input 3 digits for the page number, using the numbered buttons.
If you make a mistake, retype the correct page number.
If the counter on the screen continues searching, it is because the page is not available.
If this is the case, input another page number
To access the next or preceding page:
Press PROG + ( ) or PROG - ().
To superimpose teletext on to the TV:
Whilst you are viewing teletext, press . Press it again to cancel teletext mode.
To freeze a teletext page:
Press / . Press it again to cancel the freeze.
To reveal concealed information (e.g: answer to a quiz):
Press / . Press it again to conceal the information.
To select a sub page:
A teletext page may consist of several sub pages. In this case the page number that appears on the
upper left corner will change from white to green and one or more arrows will appear next to the page
number. Repeatedly press the or buttons on the remote control to watch the desired sub page.
To Switch Off Teletext:
Press .
Fastext
Fastext service lets you access Teletext pages with one button push.
When you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at the bottom
of the teletext page. Press the appropriate coloured button (red, green, yellow or blue) to access
the page corresponding to your menu choice.
Teletext
TELETEXT
Index
Programme
News
Sport
Weather
25
153
101
98
19
GB
NexTView*
*(depending on availability of service).
NexTView is an on-screen electronic programme guide, providing you with programme information for different
broadcasters.
When looking for information you can search by theme (sports, art, etc...) or date.
If wrong characters appear when viewing NexTView, use the menu system to enter the “Language/Country” menu (see page
14) and select the same language as the NexTView is broadcasted.
Displaying NexTView
1 Select a broadcast channel providing a NexTView service. In this case the indication “NexTView” is displayed as soon as data
is available.
2 To see NexTView service you have two different types of NexTView interface. These depend on the % of available data:
a)
“Programme List” interface:
Whilst you are watching TV, and after the indication “NexTView” (coloured white) is displayed on the screen, press the
button on the remote control to watch the “Programme List” interface (see fig. 1).
b) “Overview” interface:
Whilst you are watching TV, and after more than 50% of NexTView data is available (100% data may not be available
depending on the area) the indication “NexTView” (coloured black) is displayed on the screen. Press the button on
the remote control to watch the “Overview” interface (see fig. 2).
As soon as you enter the NexTView service the % of NexTView data available will be shown in the bottom left corner of
the screen. Once you have entered the service, the % of data will not increase.
3 To navigate through NexTView:
• moving to right or left press or .
• moving up or downwards, press or .
• confirming a selection, press OK.
4 To switch NexTView off, press the button on the remote control.
“Programme List” interface (fig. 1): “Overview” interface (fig. 2):
* “Record” and “Remind” options will be shown on the screen as soon as a programme have been selected, but
they will not be shown if you are watching the NexTView service on a TV channel which is not a NexTView
provider.
* “Record” and “Remind” will not be available if the programme that you have selected has already started.
Icons’ key:
NexTView
full selection list:
All the programme information
is listed by time and broadcast
channels order.
entertainment
children
arts
sports
news
movie
music
channel selection:
If the NexTView provider sends
information of more than 8
broadcast channels, you can
select 8 of them to create your
personal list.
After you have created your
personal list, the default list can
be restored. To restore it, select
“Auto (” by pressing button
on the remote control.
01
Mon
TV1
TV2
TV3
TV4
TV5
TV6
TV7
TV8
00 : 30
01 : 30
05 : 30
06 : 30
07 : 30
08 : 30
09 : 30
10 : 30
Songs from the shows
Weather forecast informat i
A1 news magazine
Arts show
Oclock news
Weather forecast informat i
A1 news magazine
Arts show
02
Tue
03
Wed
04
Thu
05
Fri
06
Sat
07
Sun 7 : 07 : 01
Songs from the shows
TV1 00:30 - 01:30 Thursday 04
Programme descriptio n
Record Remind
4
5
1
2
3
01
Mon
TV1
TV2
TV3
TV4
TV5
TV6
TV7
TV8
02
Tue
03
Wed
04
Thu
05
Fri
06
Sat
07
Sun 9 : 15 : 03
9 : 00 9 : 30 10 : 00
Magazine
|
Songs from the shows
Weather Forecast
|
Mike's show
Euronews
|
Fantasy film
|
Star Wars
Home Shopping Europe
|
Euro Sports
News | Arts show
|
Magazine
Larry King's live |
Euro Sports
Euro magazine |
Euro Sports
Home Shopping Europe |
Euronews
Songs from the shows
TV1 00:30 - 01:30 Thursday 04
Programme descriptio n
Record Remind
1
2
3
4
5
4 Record*
This function only works if you have connected a VCR
which supports SmartLink and Timer Programming
feature.
If you wish to record the selected programme, press
the red button on the remote control.
5 Remind*
If you wish to be reminded when the selected programme is
broadcast, press the green button on the remote control. At the
time that programme should be broadcast a reminder
message is displayed on the TV.
1 Icons for different themes
(see the “Icons’ key” below)
2 Date
3 Programme list
remind list:
shows you the list with all the
programmes (maximum 5
programmes) that you have
selected to be reminded about.
20
Additional Information
Acceptable input signal
A No inputs
B Audio/video and RGB signal
C Audio/video and RGB signal
D Audio/video and S video signal
E S Video signal
F Video signal
G Audio signal
H No input
Available output signal
Audio signal.
Video/audio from TV tuner.
Video/audio displayed on TV screen (monitor out).
Video/audio from selected source.
No output.
No output.
No output.
Audio signal to headphones.
Connecting Optional Equipment
Using the following instructions, you can connect a wide range of optional equipment to your projection TV.
VCR
V
C
R
VCR
Decoder
Hi-fi
DVD
A
B
C
D
E
F
G
H
To avoid
picture
distortion:
Do not
connect
equipment
to E and F
connectors
at the same
time.
S-VHS/Hi8/
DVC
camcorder
8mm/Hi8/
DVC
camcorder
continued...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148

Sony KP-41PX2 Instrukcja obsługi

Kategoria
Telewizory LCD
Typ
Instrukcja obsługi

w innych językach