Legrand Smart Tru-Universal Dimmer Instrukcja instalacji

installation guide

Smart Tru-Universal Dimmer

WTRL50

2

table of contents

before you start ..................................3

what you need ...................................4

installation and setup ................ 6–19

getting to know your dimmer ... 20–21

specifications ............................. 22-23

faqs ..............................................24

warranty .......................................25

regulatory information ......... 26–29

support ........................................30

notes ............................................31

3

before you start

Review this guide in its entirety before beginning device installation. Consult an

electrician with any questions or if you are unsure of your abilities.

DWarning: Incorrect installation could

result in death, serious injury, and/or

damage to your home or devices.

DCaution: To reduce the risk of injury

and/or overheating and damage to other

equipment:

• For dry, indoor use only.

• Use ONLY with dimmable lighting loads.

• Do not use to power medical equipment.

• Do not use with loads exceeding the

device load rating (see page 22).

• Connect the smart dimmer to a

120 VAC, 60 Hz power source ONLY.

• Always use copper wire to install the

smart dimmer and follow all applicable

local and national electrical codes.

• Install in a non-metallic electrical box

to protect wireless signal strength.

Visit the Legrand website at www.legrand.us/radiant/smart-lighting.aspx to learn more

about your smart device.

4

what you need

REQUIRED:

Phillips-head screwdriver

Flat blade screwdriver

YOU MAY ALSO NEED:

Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,

ﬂashlight, radiant

®

screwless wallplate (included), wiring leads (included), and

wire nuts (included)

NOTE: Exercise caution when using power tools. Overtightening the screws can

damage the device.

5

6

installation & setup

step one

|

turn off the power for your device at the

circuit breaker

Flip the existing light switch multiple times to conﬁrm the power is off.

NOTES:

• If there are multiple devices next to your existing light switch, make sure power is

off at the circuit breaker for all of those devices.

• For three-way installations using a remote dimmer, follow the instructions for the

remote device (WTRL60).

7

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

8

installation & setup

step two

|

remove the existing device

Check for the following wires:

1

HOT or LINE: Receives power from the circuit box. Referred to as “Hot” for the

purposes of this guide.

2

LOAD: Directs power to your light(s).

3

NEUTRAL: Creates a path to return current to the power source when the

device is off. Required for your dimmer installation.

4

GROUND: Provides a safe path for electricity in the event of a short circuit.

NOTE: Refer to the “faqs” on page 24 if you are unsure of your wiring.

9

OFF

ON

OFF

ON

OFF

ON

VOLTAGE

TESTER

Load

Supply

“Hot”

10

installation & setup

step three

|

wire the smart dimmer

When connecting each wire, loosen the terminal screw, insert the wire into a

terminal slot, and tighten the terminal screw until the wire is secured.

1

Connect the neutral wires to the WHITE terminal slots.

2

Connect the load wire to any LOAD terminal slot.

3

Connect the hot wire to any HOT terminal slot.

4

Connect the ground wire to the green wiring lead on the device. Use a wire nut

to secure the wires together.

NOTE: If you need extra length on your wires, wire leads are included in your packaging.

11

OFF

ON

OFF

ON

OFF

ON

Load

Supply

“Hot”

Terminal screw

Terminal

slot

NOTE: For multi-gang installations,

refer to “speciﬁcations” on page 22.

12

installation & setup

step four

|

secure the smart dimmer

1

Gently fold the wires into the electrical box. Be careful not to pinch a wire or

loosen anywire nuts.

2

Use the device screws to secure the smart dimmer to the electrical box. Do

not fully tighten the screws.

13

14

installation & setup

step five

|

test the smart dimmer

NOTE: See page 20 for feature details.

1

Turn the power back on at the circuit breaker.

2

Press the paddle switch to turn your light on and off.

3

Use the dimmer paddle to adjust the level of your light(s).

TROUBLESHOOTING TIP:

If the device is not powering, reference the “faqs” on page 24 to determine if you have

reversed the “hot” and “load” wiring.

15

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

16

installation & setup

step six

|

attach the screwless wall plate

1

Noting which side faces out, align the sub-plate over the device screws. Use

the sub-plate screws (provided) to secure the sub-plate to the smart dimmer.

2

Tighten the device screws to secure the smart dimmer to the electrical box.

3

Angle the end of the screwless wall plate over the top edge of the

sub-plate. Push the screwless wall plate down and in until it “snaps” into

place over the sub-plate.

NOTE: To remove the wall plate, place the tip of a ﬂat blade screwdriver into the slot under

the wall plate and twist gently.

17

THIS SIDE OUT

MOUNT OVER DEVICE

THIS SIDE OUT

MOUNT OVER DEVICE

THIS SIDE OUT

MOUNT OVER DEVICE

1 32

18

19

installation & setup

step seven

|

set up your system

1

Download and launch the Smart Lights Thread app by Legrand. The app is

available on the App Store or on Google Play.

2

Connect your smart hub (WTH1) by following the smart hub installation guide

instructions and the self-guided app instructions.

3

Connect your smart dimmer to the smart hub by following the instructions

within the app.

Google Play and the Google Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

20

getting to know your dimmer

Item Name Description

1

Paddle

Switch

• Press the top of the paddle to turn the light on or double-tap to

raise the dimming percentage to 100%.

• Press the bottom of the paddle to turn the light off.

• To return the dimmer to factory default, press and hold the top

paddle for 15 seconds. The LED illuminates a solid amber color.

• To complete the factory reset, you must also remove the device

from your Samsung Artik Cloud account before it can be

recommissioned with your existing Hub or a new Hub.

2

LED Locator

Light

Indicates the current state of the device. Refer to “LED Locator

Light Explanations” for detail.

3

Dimmer

Paddle and

LED Light

Level

Controls and displays the dimming percentage:

• Press (+/-) to adjust the dimming level incrementally.

• Press and hold (+/-) to quickly change the dimming level.

4

Air Gap

Switch

Completely turns off the dimmer. Use when changing light

bulbs.

Strona jest ładowana ...

Legrand Smart Tru-Universal Dimmer Instrukcja instalacji

Legrand Smart Tru-Universal Dimmer Instrukcja instalacji

w innych językach

Powiązane dokumenty

Inne dokumenty