Interlogix IFS NS2052-4P-1T Instrukcja obsługi

Marka: Interlogix

Model: IFS NS2052-4P-1T

Kategoria: Przełączniki sieciowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

of their respective owners. Information in this document is subject to change without notice.

IFS MC252-4P-1S and NS2052-4P-1T User

Manual

Package contents

Unless specified, the term “industrial PoE+ switch”

mentioned in this user manual refers to the MC252-4P-1S and

the NS2052-4P-1T.

Open the box of the industrial PoE+ switch and carefully

unpack it. The box should contain the following items:

• Industrial PoE+ switch × 1

• Dust cap × 4

• Wall-mount kit × 1

If any of these are missing or damaged, please contact your

dealer immediately. If possible, retain the carton including the

original packing material, and use them again to repack the

product in case there is a need to return it to us for repair.

Product features

Physical port

Model Name

10/100 Mbps

RJ45 Ports

100FX SFP

Slots

PoE Ports

NS2052-4P-1T 5 - 4

MC252-4P-1S 4 1 4

Interface

• NS2052-4P-1T: Four 10/100BASE-TX Fast Ethernet IEEE

802.3at PoE+ RJ45 copper ports (Port-1 to Port-4)

• MC252-4P-1S: Four 10/100BASE-TX Fast Ethernet RJ45

copper ports with IEEE 802.3at PoE+ Injector (Port-1 to

Port-4)

• NS2052-4P-1T:One 10/100BASE-TX Fast Ethernet non-

PoE RJ45 copper port.

• MC252-4P-1S: One 100BASE-FX SFP interface

• One terminal block for master and slave power input

(Power Range: 12~48 VDC redundant power).

• Hardware DIP switch for Standard, VLAN, and Extend

mode selection; the Extend mode features a 25 W PoE

transmission distance of 250 m at a speed of 10 Mbps

(Port-1 to Port-4 only).

Power over Ethernet

• Complies with IEEE 802.3at Power over Ethernet Plus,

end-span PSE

• Backward compatible with IEEE 802.3af Power over

Ethernet

• Up to four ports of IEEE 802.3af/at devices powered

• Up to 120 W PoE budget

• Supports PoE power up to 36 W for each PoE port

• Each port supports 54 VDC power to PoE powered device

• Auto detects powered device (PD)

• Circuit protection prevents power interference between

ports

• Remote power feeding up to 100 m in standard mode with

250 m in extend mode (switch selectable)

Switching

• Hardware-based 10/100 Mbps (half/full duplex), auto-

negotiation, and auto MDI/MDI-X

• Features Store-and-Forward mode with wire-speed

filtering and forwarding rates

• IEEE 802.3x flow control for full duplex operation and back

pressure for half duplex operation

• 2K MAC address table size

• 10K jumbo frame

• IEEE 802.1Q VLAN transparency

• Automatic address learning and address aging

• Supports CSMA/CD protocol

Industrial case and installation

• IP40 metal case

• DIN-rail, wall-mount design

• 12~48 VDC redundant power with polarity reverse protect

function

• Fault alarm for power input failed

• Supports 5 KV DC Ethernet ESD protection

• -40 to 75°C operating temperature

• Four real-time PoE power usage indicators

2 / 9 P/N 1073625-EN • REV A • ISS 17APR19

Product description

Cost-effective full PoE+ power solution ideal for hardened

environment

Featuring Plug and Play designed to be installed in heavy

industrial demanding environments, the industrial PoE+

switches are industrial-grade, DIN-rail type unmanaged Fast

Ethernet PoE+ switches with four 10/100BASE-TX PoE+ ports,

with one additional Fast Ethernet (NS2052-4P-1T) or

100BASE-FX fiber optic (MC252-4P-1S) interface for video

uplink. The industrial PoE+ switches are designed with a

redundant power system and operate reliably, stably, and

quietly in any hardened environment without affecting

performance. It comes with a total power budget of up to 120

W for different kinds of PoE applications and an operating

temperature ranging from -40 to 75°C in a rugged IP40 metal

housing.

Extension of ethernet data transmission distance

The industrial PoE+ switch has a built-in solid DIP switch

providing Standard, VLAN, and Extend operation modes. By

default, the industrial PoE+ switch operates as a normal IEEE

802.3af/at PoE+ switch in the “Standard” operation mode.

The "VLAN" operation mode features with port-based VLAN

function helps to prevent the IP camera’s multicast or

broadcast storm from influencing each other.

In the “Extend” operation mode, the industrial PoE+ switch

operates on a per-port basis at 10 Mbps full duplex operation

and can support 25 W PoE power output over a distance of up

to 250 meters, overcoming the 100-meter limit on Ethernet

UTP cable.

Convenient and reliable power system

To facilitate the 802.3at PoE+ usage with commonly used

12~48V DC power input for transportation and industrial-lev el

applications, the industrial PoE+ switch adopts 12~48 VDC to

54V power boost technology to solve power source issues but

does not require special power supplies. The industrial PoE+

switch provides an integrated power solution with a wide range

of voltages (12~48 VDC) for worldwide operability. It also

provides dual-redundant, reversible polarity 12~48 VDC power

supply inputs for high availability applications.

Environmentally hardened design

With the IP40 metal industrial case, the industrial PoE+ switch

provides a high level of immunity against electromagnetic

interference and heavy electrical surges which are usually

found on plant floors or in curb-side traffic control cabinets

without air conditioning. It features a ventilated construction in

which a cooling fan is not necessary, thereby making its

operation noiseless. Being able to operate under the

temperature range from -40 to 75°C, the industrial PoE+ switch

can be placed in almost any difficult environment.

Robust protection

The industrial PoE+ switch provides contact discharge of ±5

KV DC and air discharge of ±5 KV DC for Ethernet ESD

protection. It also supports ±5 KV surge immunity to improve

product stability and protects users’ networks from devastating

ESD attacks, making sure the flow of operation does not

fluctuate.

Hardware introduction

Switch front panel

Figure 1: Industrial PoE+ switch front panels

NS2052-4P-1T

MC252-4P-1S

Fast Ethernet TP interfaces

10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters.

100BASE-FX SFP slot (MC252-4P-1S)

100BASE-FX mini-GBIC slot, SFP (Small Factor Pluggable)

transceiver module: From 2 kilometers (multi-mode fiber) to

20/40/60 kilometers (single-mode fiber).

DIP switch

The industrial PoE+ switch provides one DIP switch for

Standard, VLAN, and Extended mode selections. The detailed

descriptions are shown in the following table.

DIP Switch Mode

Function

Standard

In this mode, the industrial PoE+ switch operates

as a general switch and all PoE ports operate at

10/100Mbps auto-negotiation.

VLAN

In this mode, the industrial PoE+ switch operates

as a VLAN isolation switch and

1. Port 1 to port 4 will isolate respectively.

2. Port 1 to port 4 can only communicate with

port 5.

Note: After adjusting the VLAN DIP switch,

reboot the industrial PoE+ switch to effectuate

the

change.

Extended

In this mode, the industrial PoE+ switch operates

on a per-port basis at 10 Mbps full duplex

operation but can support IEEE 802.3af PoE

power output over a distance of up to 250 meters

overcoming the 100 m limit on a Ethernet UTP

cable.

P/N 1073625-EN • REV A • ISS 17APR19 3 / 9

LED indicators

System

LED Color Function

P1 Green Lit: indicates power 1 has power.

P2 Green Lit: indicates power 2 has power.

FAULT Red

Lit: indicates either power 1 or power 2 has

no power.

30W Orange

Off: indicates the PoE usage is less than 14

Blinking: indicates that the PoE usage is

around 15 to 29 W.

Lights: indicates the PoE usage is

around/over 30 W.

60W Orange

Blinking: indicates that the PoE usage is

around 45 to 59 W.

Lit: indicates the PoE usage is around/over

60 W.

90W Orange

Blinking: indicates that the PoE usage is

around 75 to 89 W.

Lit: indicates the PoE usage is around/over

90 W.

120W Orange

Blinking: indicates that the PoE usage is

around 100 to 119 W.

Lit: indicates the PoE usage is at the

maximum.

Per 802.3at PoE+ 10/100BASE-TX Interface (Port 1 to Port

LED Color Function

Link/ACT Green

Lit: indicates the port is successfully

connecting to the network at 10 Mbps or

100 Mbps.

Blinking: indicates that the port is actively

sending or receiving data.

PoE in

Use

Orange

Lit: indicates the port is providing DC in-line

power.

Off: indicates the connected device is not a

PoE powered device (PD).

Per 10/100BASE-TX Interface (Port 5 of NS2052-4P-1T)

LED Color Function

Link/ACT Green

Lit: indicates the port is successfully

connecting to the network at 10 or 100

Mbps.

Blinking: indicates that the port is actively

sending or receiving data.

Per 100FX SFP Slot (Port 5 of MC252-4P-1S)

LED Color Function

Link/ACT Green

Lit: indicates the port is successfully

connecting to the network at 100 Mbps.

Blinking: indicates that the port is actively

sending or receiving data.

Switch upper panel

The upper panel of the industrial PoE+ switch consists of one

terminal block connector within two DC power inputs.

Figure 2 below shows the upper panel of the industrial PoE+

switch.

Figure 2: Industrial PoE+ switch upper panel

Wiring the power inputs

The six-contact terminal block connector on the top panel of

industrial PoE+ switch is used for two DC redundant power

inputs. Follow the steps below to insert the power wire.

Caution: When performing procedures like inserting the wires

or tightening the wire-clamp screws, ensure that the power is

OFF to prevent electrical shock.

1. Insert positive and negative DC power wires into contacts

1 and 2 for Power 1 or 5, and 6 for Power 2.

2. Tighten the wire-clamp screws for preventing the wires

from loosening.

Power 1

Fault

Power 2

Notes:

1. The wire gauge for the terminal block should be in the

range between 12 and 24 AWG.

2. The DC power input range is 12 to 48 VDC.

4 / 9 P/N 1073625-EN • REV A • ISS 17APR19

3. When the DC power input range is 12 V, the PoE budget is

60 W;

When the DC power input range is 24 V, the PoE budget is

90 W;

When the DC power input range is 48 V, the PoE budget is

120 W.

To avoid damage, use the industrial PoE+ switch under its

specification.

Wiring the fault alarm contact

The fault alarm contacts are in the middle of the terminal block

connector. Upon inserting the wires, the industrial PoE+ switch

detects the fault status of the power failure and then forms an

open circuit. The following illustration shows an application

example for wiring the fault alarm contacts.

Insert the wires into the fault alarm contacts.

Note:

1. The wire gauge for the terminal block should be in the

range between 12 to 24 AWG.

2. Alarm relay circuit accepts up to 24 V, max. 1 A currents.

Mounting

Note: Ensure that the industrial PoE+ switch is mounted

vertically with the power connectors on the top and a minimum

of three inches above and below the switch to allow for proper

air flow. This device uses a convection flow of hot air which

rises and brings cold air in from the bottom and out of the top

of the device. Do not mount the switch horizontally as this does

not allow air to flow up into the device and will result in damage

to the switch. Do not tie DC1 to DC2. DC2 is for secondary

power redundancy. Do not plug DC power into the device while

the AC power cord is plugged in. This is not a hot-swappable

switch. Hot-swapping this device will result in damage.

DIN-rail mounting installation

To replace the wall-mount application with DIN-rail application

on the industrial PoE+ switch, refer to the following figures to

screw the DIN-rail on the industrial PoE+ switch.

To hang the industrial PoE+ switch, follow the steps below:

1. Screw the DIN-rail on the industrial PoE+ switch.

2. Place the bottom of DIN-rail lightly into the track.

3. Ensure that the DIN-rail is secured to the track.

To remove the industrial PoE+ switch from the track, carefully

pull out the bottom of the DIN-rail to remove it from the track.

P/N 1073625-EN • REV A • ISS 17APR19 5 / 9

Wall-mount plate mounting

To install the industrial PoE+ switch on the wall, follow the

steps below.

1. Remove the DIN-rail from the industrial PoE+ switch.

Loosen the screws to remove the DIN-rail.

2. Place the wall-mount plates on the rear panel of the

industrial PoE+ switch as shown below.

3. Use the screws to screw the wall-mount plates on the

industrial PoE+ switch.

4. Use the hook holes at the corners of the wall-mount plates

to hang the industrial PoE+ switch on the wall.

5. To remove the wall-mount plates, reverse the steps

above.

Installation Steps

This section describes the functionalities of the Industrial PoE+

components and guides how to install it on the desktop. Basic

knowledge of networking is assumed. Please read this chapter

completely before installation.

1. Unpack the industrial PoE+ switch.

2. Check the DIN-Rail that is pre-installed on the industrial

PoE+ switch. (Please refer to DIN-Rail Mounting section

for DIN-Rail installation. If you want to wall mount the

industrial PoE+ switch, then please refer to Wall Mount

Plate Mounting section for specific instructions.

3. To hang the industrial PoE+ switch on the DIN-Rail track

or wall, please refer to the Mounting section.

4. Power on the industrial PoE+ switch. (Please refer to the

Wiring the Power Inputs section for power input) The

power LED on the industrial PoE+ switch illuminates.

Please refer to the LED indicators section for LED

definitions.

5. Prepare the twisted-pair, straight through Category 5 cable

for Ethernet connection.

6. Insert one side of Category 5 cables into the industrial

PoE+ switch Ethernet port (RJ-45 port) and the other side

to the network device Ethernet port (RJ-45 port), ex:

Switch, PC, or Server. The UTP port (RJ-45) LED on the

industrial PoE+ switch illuminates when the cable is

connected to the network device. Please refer to the LED

indicators section for LED definitions.

7. Insert the fiber cable from the industrial PoE+ switch to the

fiber network. TX, RX must be paired at both ends. The

optical port LED on the MC252-4P-1S illuminates when

the connection is established with a network device.

Please refer to the LED indicators section for LED

definitions.

8. When all connections are set up and the LEDs illuminate,

the installation is complete.

Troubleshooting

This section contains issue-solving information. If the industrial

PoE+ switch is not functioning properly, ensure that the

industrial PoE+ switch was set up according to instructions in

this manual.

Issue Solution

The per port LED does

not illuminate.

Check the cable connection and try

swapping out a cable.

Performance is poor

Check the speed duplex mode of the

partner device. The industrial PoE+

switch is run in auto-negotiation mode

and if the partner is set to half duplex,

then the performance will be poor.

The per port LED

illuminates, but the

traffic is irregular.

Ensure that the attached device is not

set to dedicated full duplex. Some

devices use a physical or software

switch to change duplex modes. Auto-

negotiation may not recognize this type

of full-duplex setting.

The industrial PoE+

switch doesn’t

connect to the network

Check the per port LED and/or try

another port on the industrial PoE+

switch. Ensure that the cable is installed

properly and is the correct type. Turn off

the power and then, after a while, turn

on the power again.

Product specifications

MC252-4P-1S

Hardware specifications

Fast Ethernet

Copper Ports

Four 10/100BASE-TX RJ45 auto-MDI/MDI-

X ports

PoE Injector Port

Four ports with 802.3af/at PoE+ injector function

(Port-1 to Port-4)

SFP Port One 100BASE-FX SFP port

Switch Architecture

Store-and-Forward

Switch Fabric 1 Gbps/non-blocking

Switch

Throughput@64

bytes

0.74 Mpps @64 bytes

MAC Address

Table

2K entries

Flow Control

IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

Jumbo Frame 10 Kbytes

DIP Switch (Port-1

to Port-4)

Standard mode: 30 W PoE transmission distance

of 100 m at speed of 10/100 Mbps.

VLAN mode: "Port-

based VLAN Protection" where

ports can be isolated from each other via one DIP

switch. Only Port-5 can visit other ports.

Extend mode: 25 W PoE transmission distance of

6 / 9 P/N 1073625-EN • REV A • ISS 17APR19

250 m at a speed of 10 Mbps (switch selectable).

Connector

Removable 6-pin terminal block:

Pin 1/2 for Power 1

Pin 3/4 for power fault alarm

Pin 5/6 for Power 2

Alarm

One relay output for power failure.

Alarm relay current carry ability: 1 A @ 24 VAC

Power

requirements

12 to 48 VDC, 7 A (max.)

Power

Consumption/

Dissipation

4.3 W, 14.6 BTU (Standby without PoE function)

at DC 12 V power input

72.5 W, 247.4 BTU (Full loading with PoE

function) at DC 12 V power input

5 W, 17 BTU (Standby without PoE function) at

DC 24 V power input

103.9 W, 354.5 BTU (Full loading with PoE

function) at DC 24 V power input

5.3 W, 18.1 BTU (Standby without PoE function)

at DC 48V power input

135.8 W, 463.4 BTU (Full loading with PoE

function) at DC 48 V power input

Dimensions (W ×

× H)

50 × 85.1 × 135 mm

Weight 598 g

ESD protection 5 KV DC

Enclosure IP40 metal case

Installation DIN rail kit and wall-mount ear

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus / PSE

PoE Power Supply

Type

End-Span

Power Pin

Assignment

1/2(+), 3/6(-)

PoE Power Output 54 VDC Per Port, Max. 36 W

PoE Power Budget

(max.)

60 W @ 12 VDC input

90 W @ 24 VDC input

120 W @ 48 VDC input

Max. Number of

Class 2 PDs

Max. Number of

Class 3 PDs

Max. Number of

Class 4 PDs

Standards conformance

Regulatory

compliance

FCC Part 15 Class A, CE

Stability testing

IEC60068-2-32 (Free Fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Standards

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3z Gigabit SX/LX

IEEE 802.3x Flow Control and Back Pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

Environment

Temperature

Operating: -40 to +75°C

Storage: -40 to 85°C

Humidity 5% to 95% (non-condensing)

NS2052-4P-1T

Hardware specifications

Fast Ethernet

Copper Ports

Five 10/100BASE-TX RJ45 auto-MDI/MDI-

X ports

(Port-1 to Port-5)

PoE Injector Port

Four ports with 802.3af/at PoE+ injector function

(Port-1 to Port-4)

Switch Architecture

Store-and-Forward

Switch Fabric 1 Gbps/non-blocking

Switch

Throughput@64

bytes

0.74 Mpps @64 bytes

MAC Address

Table

2K entries

Flow Control

IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

Jumbo Frame 10 Kbytes

DIP Switch (Port-1

to Port-4)

Standard mode: 30 W PoE transmission distance

of 100 m at speed of 10/100 Mbps.

VLAN mode: "Port-

based VLAN Protection" where

ports can be isolated from each other via one DIP

switch. Only Port-5 can visit other ports.

Extend mode: 25 W PoE transmission distance of

250 m at a speed of 10 Mbps (switch selectable).

Connector

Removable 6-pin terminal block:

Pin 1/2 for Power 1

Pin 3/4 for power fault alarm

Pin 5/6 for Power 2

Alarm

One relay output for power failure.

Alarm relay current carry ability: 1 A @ 24 VAC

Power

requirements

12 to 48 VDC, 7 A (max.)

Power

Consumption/

Dissipation

3.7 W, 12.6 BTU (Standby without PoE function)

at DC 12 V power input

70 W, 238.8 BTU (Full loading with PoE function)

at DC 12 V power input

4.6 W, 15.7 BTU (Standby without PoE function)

at DC 24 V power input

105.1 W, 358.6 BTU (Full loading with PoE

function) at DC 24 V power input

4.8 W, 16.4 BTU (Standby without PoE function)

at DC 48V power input

136.8 W, 466.8 BTU (Full loading with PoE

function) at DC 48 V power input

Dimensions (W ×

× H)

50 × 85.1 × 135 mm

Weight 596 g

ESD protection 5 KV DC

Enclosure IP40 metal case

Installation DIN rail kit and wall-mount ear

P/N 1073625-EN • REV A • ISS 17APR19 7 / 9

Power over Ethernet

PoE Standard IEEE 802.3at Power over Ethernet Plus / PSE

PoE Power Supply

Type

End-Span

Power Pin

Assignment

1/2(+), 3/6(-)

PoE Power Output 54 VDC Per Port, Max. 36 W

PoE Power Budget

(max.)

60 W @ 12 VDC input

90 W @ 24 VDC input

120 W @ 48 VDC input

Max. Number of

Class 2 PDs

Max. Number of

Class 3 PDs

Max. Number of

Class 4 PDs

Standards conformance

Regulatory

compliance

FCC Part 15 Class A, CE

Stability testing

IEC60068-2-32 (Free Fall)

IEC60068-2-27 (Shock)

IEC60068-2-6 (Vibration)

Standards

Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab Gigabit 1000BASE-T

IEEE 802.3x Flow Control and Back Pressure

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

Environment

Temperature

Operating: -40 to +75°C

Storage: -40 to 85°C

Humidity 5% to 95% (non-condensing)

Appendix: Networking

connection

RJ45 pin assignments

1000Mbps, 1000BASE-T

Contact MDI MDI-X

1 BI_DA+ BI_DB+

2 BI_DA- BI_DB-

3 BI_DB+ BI_DA+

4 BI_DC+ BI_DD+

5 BI_DC- BI_DD-

6 BI_DB- BI_DA-

7 BI_DD+ BI_DC+

8 BI_DD- BI_DC-

10/100Mbps, 10/100BASE-TX

Contact

MDI

Media Dependent

Interface

MDI-X

Media Dependent

Interface-Cross

1 Tx + (transmit) Rx + (receive)

2 Tx - (transmit) Rx - (receive)

3 Rx + (receive) Tx + (transmit)

4, 5 Not used

6 Rx - (receive) Tx - (transmit)

7, 8 Not used

RJ45 cable pin assignments

The standard RJ45 receptacle/connector

There are eight wires on a standard UTP/STP cable and each

wire is color-coded. Figure 3 on page 8 shows the pin

allocation and color of straight-through cable and crossover

cable connection:

8 / 9 P/N 1073625-EN • REV A • ISS 17APR19

Figure 3: Straight-through and crossover cable

Straight-through cable

SIDE 1

SIDE 2

SIDE 1

1 = White / Orange

2 = Orange

3 = White / Green

4 = Blue

5 = White / Blue

6 = Green

7 = White / Brown

8 = Brown

1 = White / Orange

2 = Orange

3 = White / Green

4 = Blue

5 = White / Blue

6 = Green

7 = White / Brown

8 = Brown

SIDE 2

Crossover cable

SIDE 1

SIDE 2

SIDE 1

1 = White / Orange

2 = Orange

3 = White / Green

4 = Blue

5 = White / Blue

6 = Green

7 = White / Brown

8 = Brown

1 = White / Green

2 = Green

3 = White / Orange

4 = Blue

5 = White / Blue

6 = Orange

7 = White / Brown

8 = Brown

SIDE 2

Ensure that the connected cables have the same pin assignment and color as described above.

Regulatory information

Disclaimer

Information in this document is subject to change

without notice. No part of this document may be

reproduced or transmitted in any form or by any

means, electronic or mechanical, for any

purpose, without the express written permission

of UTC Fire & Security Americas Corporation, Inc

Trademarks and

patents

The TruVision Navigator name and logo are

trademarks of United Technologies.

Interlogix IFS NS2052-4P-1T Instrukcja obsługi

Marka: Interlogix

Model: IFS NS2052-4P-1T

Kategoria: Przełączniki sieciowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

ściągnij PDF

raport

w innych językach

English: Interlogix IFS NS2052-4P-1T User manual

Interlogix IFS NS2052-4P-1T Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Interlogix IFS NS2052-4P-1T Instrukcja obsługi

w innych językach

Inne dokumenty