Yamaha NY64 Instrukcja obsługi

Typ
Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

NY64-D
-
1
-
EnglishDeutschFrançais
Español
Português
Italiano
Русский
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Manual do Proprietário
Manuale di istruzioni
Руководство пользователя
JA
ES
KO
RU
IT
PT
FR
DE
EN
NY64-D
AUDIO INTERFACE CARD
Owner’s Manual
NY64-D
-
2
-
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT
MODIFY THIS UNIT!
This product, when installed as indicated
in the instructions contained in this man-
ual, meets FCC requirements. Modifica-
tions not expressly approved by Yamaha
may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this
product to accessories and/or another
product use only high quality shielded
cables. Cable/s supplied with this product
MUST be used. Follow all installation
instructions. Failure to follow instructions
could void your FCC authorization to use
this product in the USA.
3. NOTE: This product has been tested
and found to comply with the
requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices.
Compliance with these requirements
provides a reasonable level of assurance
that your use of this product in a
residential environment will not result in
harmful interference with other electronic
devices. This equipment generates/uses
radio frequencies and, if not installed and
used according to the instructions found
in the users manual, may cause
interference harmful to the operation of
other electronic devices. Compliance with
FCC regulations does not guarantee that
interference will not occur in all
installations. If this product is found to be
the source of interference, which can be
determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem
by using one of the following measures:
Relocate either this product or the device
that is being affected by the interference.
Utilize power outlets that are on different
branch (circuit breaker or fuse) circuits or
install AC line filter/s.
In the case of radio or TV interference,
relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not
produce satisfactory results, please
contact the local retailer authorized to
distribute this type of product. If you can
not locate the appropriate retailer, please
contact Yamaha Corporation of America,
Electronic Service Division, 6600
Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to
those products distributed by Yamaha
Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
Owner’s Manual
NY64-D
-
3
-
This applies only to products distributed by Yamaha Canada Music Ltd.
Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
(can_b_01)
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : Audio Interface Card
Model Name : NY64-D
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause
undesired operation.
See user manual instructions if interference to radio reception is suspected.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA (FCC DoC)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
-
4
-
Owner’s Manual
NY64-D
-
5
-
Owner’s Manual
NY64-D
Table of contents
Included items........................................................................................................ 5
Precautions............................................................................6
Introduction .......................................................................... 9
Main features ......................................................................................................... 9
Updating the firmware ........................................................................................... 9
Card installation ..................................................................................................... 9
Dante support........................................................................................................ 9
Device features ....................................................................10
How to read the [SYNC] indicators ...................................... 11
Specifications.......................................................................13
General Specifications .......................................................................................... 13
Dimensions .......................................................................................................... 14
Included items
Owner's Manual (this document)
Dante Virtual Soundcard license code
Information for Users on Collection and Disposal of Old Equipment
This symbol on the products, packaging, and/or accompanying documents
means that used electrical and electronic products should not be mixed with
general household waste. For proper treatment, recovery and recycling of old
products, please take them to applicable collection points, in accordance with
your national legislation and the Directives 2002/96/EC.
By disposing of these products correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products, please
contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
[For business users in the European Union]
If you wish to discard electrical and electronic equipment, please contact your
dealer or supplier for further information.
[Information on Disposal in other Countries outside the European Union]
This symbol is only valid in the European Union. If you wish to discard these
items, please contact your local authorities or dealer and ask for the correct
method of disposal.
(weee_eu_en_01)
-
6
-
Owner’s Manual
NY64-D
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
Please keep this manual in a safe place for future reference.
Always follow the basic precautions listed below to avoid the possibility of
serious injury or even death from electrical shock, short-circuiting, damages,
fire or other hazards. These precautions include, but are not limited to, the
following:
Before installing the card in a device, check to make sure that the device is compatible
with the card. Also, do not install the card in any Yamaha products not specified by
Yamaha for use with the card in order to avoid possible electrical shock, fire, or device
damage. Please check possible restrictions regarding the maximum number of Yamaha
and third-party expansion cards that can be simultaneously installed. Refer to the
owner’s manual supplied with the device, and/or the Yamaha Pro Audio web site at:
http://www.yamahaproaudio.com/
Do not attempt to disassemble or modify the card. Do not apply excessive force to card
connectors or other card components. Mishandling of the card may lead to shock, fire
hazard, or device failure.
Be sure to disconnect the power cable of the host device before installing the card and
connecting/disconnecting the cables (in order to eliminate shock hazard, undesired
noise, and avoid device damage).
Turn off all peripheral devices connected to the host device before installation, and
unplug all related cables.
WARNING
PACARD_en_1 1/3
-
7
-
Owner’s Manual
NY64-D
PACARD_en_1 2/3
Always follow the basic precautions listed below to avoid the possibility of
physical injury to you or others, or damage to the device or other property.
These precautions include, but are not limited to, the following:
Be sure to properly ground the host device to prevent electrical shock and/or
malfunction.
Do not touch the metallic leads (pins) of the circuit board when handling the card. The
pins are sharp and may cause hand cuts.
Wear a pair of heavy gloves during installation to avoid scratching or cutting your hands
on sharp edges.
NOTICE
To avoid the possibility of malfunction/ damage to the product, damage to data, or
damage to other property, follow the notices below.
Handling and maintenance
Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile phone, or
other electric devices. Otherwise, the device, TV, or radio may generate noise.
Do not expose the device to excessive dust or vibration, or extreme cold or heat (such as in
direct sunlight, near a heater, or in a car during the day), in order to prevent the possibility
of panel disfiguration, unstable operation, or damage to the internal components.
Do not place vinyl, plastic or rubber objects on the device, since this might discolor the
panel.
When cleaning the device, use a dry and soft cloth. Do not use paint thinners, solvents,
cleaning fluids, or chemical-impregnated wiping cloths.
Condensation can occur in the device due to rapid, drastic changes in ambient
temperature—when the device is moved from one location to another, or air
conditioning is turned on or off, for example. Using the device while condensation is
present can cause damage. If there is reason to believe that condensation might have
occurred, leave the device for several hours without turning on the power until the
condensation has completely dried out.
Drain all static electricity from your clothing and body before handling the card.
Static electricity can damage the card. Touch an exposed metal part of the host device
or other grounded object beforehand.
Do not drop screws or other small parts inside the card. If power is applied while screws
or similar metal objects are loose inside the unit the card may malfunction or be
damaged. If you cannot retrieve dropped objects yourself, refer the problem to qualified
Yamaha service personnel.
CAUTION
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the device, or data that is lost or destroyed.
-
8
-
Owner’s Manual
NY64-D
Information
About this manual
The illustrations as shown in this manual are for instructional purposes only.
The company names and product names in this manual are the trademarks or
registered trademarks of their respective companies.
Software may be revised and updated without prior notice.
European models
Purchaser/User Information specified in EN55103-2:2009.
Conforms to Environments: E1, E2, E3 and E4
PACARD_en_1 3/3
-
9
-
Owner’s Manual
NY64-D
Introduction
Thank you for purchasing the Yamaha NY64-D audio interface card. The NY64-D is a
digital audio interface card designed for use with NY card form factor card slots, and
supports the Dante gigabit Ethernet digital audio network.
In order to take full advantage of this product's features, and to enjoy years of trouble-free
use, please read this document before you begin using the product. After you have read
this document, please keep it in a safe place.
Main features
Supports 64 inputs and 64 outputs of 32-bit, 48 kHz uncompressed digital audio signals
In addition to simple daisy chaining, supports redundant connections through its
primary and secondary data paths
Features various indicators that indicate status and errors
Updating the firmware
The Dante firmware contained in this product can be updated to take advantage of new
features, feature improvements, and bug fixes.
Details about updating the firmware are available online.
http://www.yamahaproaudio.com/
For information about updating and setting up the console, please refer to the firmware
update guide available on the website.
Card installation
When inserting or removing this card, refer to the operating instructions included with the
other device for instructions and safety information.
Dante support
This product uses the Dante digital audio network protocol to send and receive audio
signals. Dante is a protocol developed by Audinate that is designed to deliver multichannel
audio signals at various sampling and bit rates, as well as device control signals over a
Gigabit Ethernet network.
For information about Dante, please visit the Audinate website.
http://www.audinate.com/
You can also find information about Dante and Dante-compatible products on the Yamaha
Pro Audio website.
http://www.yamahaproaudio.com
NOTE
When updating this product's Dante module firmware, make sure you also update the Dante module
firmware contained in other connected devices.
-
10
-
Owner’s Manual
NY64-D
Device features
1 [PRIMARY] and [SECONDARY] connectors
etherCON CAT5 connector that connects the card to a Dante audio network. Uses
an RJ-45 connector.
Supports star and daisy-chain arrangements.
2 [LINK/ACT] indicators
Flash in green when the corresponding PRIMARY or SECONDARY connector is
sending or receiving data.
3 [1G] indicators
Indicate the connection status of the PRIMARY and SECONDARY connectors. If an
indicator is lit, the corresponding connector is connected to a Gigabit Ethernet
network. If an indicator is not lit, there is a problem with the connection. In this
case, check all network cables and switches. If you cannot resolve the problem,
please contact your nearest Yamaha representative.
4 [SYNC] indicators
Indicate the status of the Dante clock sync.
When the green indicator is lit, the device that this card is installed in is the clock
slave, and the clock is in sync.
When the green indicator is flashing, the device that this card is installed in is the clock master.
When the card is turned on, the green indicator should either light or flash; if the
indicator does not light or flash, an error has occurred.
NOTE
To avoid electromagnetic interference, use shielded twisted-pair (STP) cables that are rated
at CAT5e or higher. Use conductive tape or comparable means to make sure that the metal
parts of the cable plugs are electrically connected to the STP cable shield.
We recommend using RJ-45 plugs that are compatible with Neutrik etherCON CAT5
connectors. You can also use cables with standard RJ-45 plugs.
The maximum length of cable that can be used varies depending on the type of cable. When using
CAT5e cables, data can be sent between devices that are connected by up to 100 m of cable.
մ
ձճղձճղ
-
11
-
Owner’s Manual
NY64-D
How to read the [SYNC] indicators
You can use the [SYNC] indicators to confirm the card's status.
The indicators can relay operational status, and error status.
Operational status
The [SYNC] indicators light as follows when the card is operating normally.
Error status
The [SYNC] indicators light as follows when an error has occurred.
Refer to the "Solution" information for ways to resolve the error.
[SYNC] indicators Description Meaning
Sync in progress. The card is syncing with the
Dante network. Wait until the
card is in sync. (This may take
up to 45 seconds.)
Clock master, functioning
normally.
The card is functioning as the
clock master.
Clock slave, functioning
normally.
The card is functioning as the
clock slave and is in sync.
[SYNC] indicators Description Solution
Clock settings are incorrect. Either turn on the TF series
console's Quick Config feature,
or check the clock master and
sampling frequency settings of
the Dante Controller.
Card not connected to Dante
network.
Make sure the cables are not
damaged and that they are
connected properly.
LitOff
Flashing Off
Lit
Off
FlashingOff
Flashes 2 timesOff
How to read the [SYNC] indicators
-
12
-
Owner’s Manual
NY64-D
* When the connected device is the clock master, the green indicator flashes; when it is
the clock slave, the green indicator lights.
Cable wiring is wrong; cannot
find other Dante devices.
Check the wiring of the
Ethernet cables.
Device that is not Gigabit
Ethernet compatible is
connected.
To use Dante to send and
receive digital audio, make
sure your devices are Gigabit
Ethernet compatible.
When using a redundancy
network, [SECONDARY]
connector is sending/receiving
audio.
Check the connections of the
network connected to the
[PRIMARY] connector.
When using a redundancy
network, error was detected on
the [SECONDARY] connector.
Check the connections of the
network connected to the
[SECONDARY] connector.
[SYNC] indicators Description Solution
Flashes 3 timesOff
LitLit or flashing
FlashingLit or flashing
Flashes 2 timesLit or flashing
-
13
-
Owner’s Manual
NY64-D
Specifications
General Specifications
Sampling Frequency
Temperature Range
Digital input/output specifications
Dimensions (W x H x D) & Net weight
100(W) x 38.5(H) x 132.5(D) mm, 0.2kg
* The contents of this manual apply to the latest specifications as of the printing date. To obtain
the latest manual, access the Yamaha website then download the manual file.
* Der Inhalt dieser Bedienungsanleitung gilt für die neuesten Technischen Daten zum Zeitpunkt
der Drucklegung. Um die neueste Version der Anleitung zu erhalten, rufen Sie die Website
von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter.
* Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques
connues à la date d’impression du manuel. Pour obtenir la version la plus récente du manuel,
accédez au site Web de Yamaha puis téléchargez le fichier du manuel concerné.
* El contenido de este manual es aplicable a las últimas especificaciones en la fecha de impresión.
Para obtener el último manual, acceda al sitio web de Yamaha y descargue el archivo del manual.
* O conteúdo deste manual se aplica às especificações mais recentes a partir da data da
impressão. Para obter o manual mais recente, acesse o site da Yamaha e faça o download
do arquivo do manual.
* Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla
data di stampa. Per ottenere la versione più recente del manuale, accedere al sito Web
Yamaha e scaricare il file corrispondente.
* В содержании данного руководства приведены последние на момент публикации
технические характеристики. Для получения последней версии руководства
посетите веб-сайт корпорации Yamaha и загрузите файл с руководством.
* 본 설명서의 내용은 인쇄일 현재 최신 사양을 기준으로 하고 있습니다 . 최신 설명서를 가져오려면 Yamaha
웹사이트에 접속 후 해당 설명서 파일을 다운로드받으십시오 .
Conditions Min. Typ. Max. Unit
External Clock Frequency 44.1kHz / 48kHz -200 +200 ppm
Accuracy +4.1667%/+0.1%/-0.1%/-4.0% to all of the above -200 +200 ppm
Conditions Min. Typ. Max. Unit
Temperature Range Operating temperature range 0 40 °C
Storage temperature range -20 60 °C
Terminal Format
Data length
Level Audio Connector
Primary / Secondary Dante 24 or 32bit 1000BASE-T 64ch ( NY64-D to other devices)
64ch (Other devices to NY64-D)
etherCON Cat5e
Specifications
-
14
-
Owner’s Manual
NY64-D
Dimensions
NY64-D
Unit: mm
100
38.5
132.5
126.7
5.8
For details of products, please contact your
nearest Yamaha representative or the authorized
distributor listed below.
Pour plus de détails sur les produits, veuillez-vous
adresser à Yamaha ou au distributeur le plus proche
de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten
aufgeführten Niederlassung und bei Yamaha Vertragshändlern
in den jeweiligen Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda
Yamaha más cercana o el distribuidor autorizado
que se lista debajo.
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Toronto, Ontario,
M1S 3R1, Canada
Tel: +1-416-298-1311
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Avenue, Buena
Park, CA 90620, U.S.A.
Tel: +1-714-522-9011
MEXICO
Yamaha de México, S.A. de C.V.
Av. Insurgentes Sur 1647 Piso 9,
Col. San José Insurgentes,
Delegación Benito Juárez, México,
D.F., C.P. 03900
Tel: +52-55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Rua Fidêncio Ramos, 302 – Cj 52 e
54 – Torre B – Vila Olímpia – CEP
04551-010 – São Paulo/SP, Brazil
Tel: +55-11-3704-1377
ARGENTINA
Yamaha Music Latin America, S.A.,
Sucursal Argentina
Olga Cossettini 1553, Piso 4 Norte,
Madero Este-C1107CEK,
Buenos Aires, Argentina
Tel: +54-11-4119-7000
VENEZUELA
Yamaha Musical de Venezuela, C.A.
AV. Manzanares,
C.C. Manzanares Plaza, Piso 4,
Oficina 0401, Baruta, Caracas,
Venezuela
Tel: +58-212-943-1877
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Edif. Torre Banco General, Piso 7,
Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, República de
Panamá
Tel: +507-269-5311
THE UNITED KINGDOM/
IRELAND
Yamaha Music Europe GmbH (UK)
Sherbourne Drive, Tilbrook,
Milton Keynes, MK7 8BL, U.K.
Tel: +44-1908-366700
GERMANY
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-303-0
SWITZERLAND/
LIECHTENSTEIN
Yamaha Music Europe GmbH,
Rellingen, Branch Switzerland in
Zürich
Seefeldstrasse 94, 8008 Zürich,
Switzerland
Tel: +41-44-3878080
AUSTRIA/BULGARIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
CZECH REPUBLIC/
HUNGARY/ROMANIA/
SLOVAKIA/SLOVENIA
Yamaha Music Europe GmbH
Branch Austria
Schleiergasse 20, 1100 Wien, Austria
Tel: +43-1-60203900
POLAND/LITHUANIA/
LATVIA/ESTONIA
Yamaha Music Europe GmbH
Sp.z o.o. Oddzial w Polsce
ul. Wrotkowa 14, 02-553 Warsaw,
Poland
Tel: +48-22-880-08-88
MALTA
Olimpus Music Ltd.
Valletta Road, Mosta MST9010,
Malta
Tel: +356-2133-2093
NETHERLANDS/BELGIUM/
LUXEMBOURG
Yamaha Music Europe Branch
Benelux
Clarissenhof 5b, 4133 AB Vianen,
The Netherlands
Tel: +31-347-358040
FRANCE
Yam aha M us i c Eu ro pe
7 rue Ambroise Croizat,
Zone d'activités de Pariest,
77183 Croissy-Beaubourg, France
Tel: +33-1-6461-4000
ITALY
Yamaha Music Europe GmbH,
Branch Italy
Viale Italia 88, 20020,
Lainate (Milano), Italy
Tel: +39-02-93577-1
SPAIN/PORTUGAL
Yamaha Music Europe GmbH
Ibérica, Sucursal en España
Ctra. de la Coruna km. 17,200,
28231 Las Rozas de Madrid, Spain
Tel: +34-91-639-88-88
GREECE
Philippos Nakas S.A. The Music
House
19th klm. Leof. Lavriou 190 02
Peania – Attiki, Greece
Tel: +30-210-6686168
SWEDEN/FINLAND/
ICELAND
Yamaha Music Europe GmbH
Germany filial Scandinavia
JA Wettergrensgata 1,
400 43 Göteborg, Sweden
Tel: +46-31-89-34-00
DENMARK
Yamaha Music Denmark,
Fillial of Yamaha Music Europe
GmbH, Tyskland
Generatorvej 8C, ST. TH. ,
2860 Søborg, Denmark
Tel: +45-44-92-49-00
NORWAY
Yamaha Music Europe GmbH
Germany - Norwegian Branch
Grini Næringspark 1, 1361 Østerås,
Norway
Tel: +47-6716-7800
RUSSIA
Yamaha Music (Russia) LLC.
Room 37, entrance 7, bld. 7,
Kievskaya street, Moscow, 121059,
Russia
Tel: +7-495-626-5005
NORTH AMERICA
CENTRAL &
SOUTH AMERICA
EUROPE
OTHER EUROPEAN
COUNTRIES
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-3030
Yam ah a M us ic G u l f F ZE
JAFZA-16, Office 512,
P.O.Box 17328,
Jebel Ali FZE, Dubai, UAE
Tel: +971-4-801-1500
TURKEY
Yamaha Music Europe GmbH
Merkezi Almanya Türkiye
İstanbul Şubesi
Maslak Meydan Sodak,
Spring Giz Plaza Bagimsiz Böl. No:3,
Sanyer Istanbul, Turkey
Tel: +90-212-999-8010
CYPRUS
Yamaha Music Europe GmbH
Siemensstrasse 22-34,
25462 Rellingen, Germany
Tel: +49-4101-303-0
OTHER COUNTRIES
Yam ah a M us ic G u l f F ZE
JAFZA-16, Office 512,
P.O.Box 17328, Jebel Ali FZE,
Dubai, UAE
Tel: +971-4-801-1500
THE PEOPLE’S REPUBLIC
OF CHINA
Yamaha Music & Electronics
(China) Co.,Ltd.
2F, Yunhedasha, 1818 Xinzha-lu,
Jingan-qu, Shanghai, China
Tel: +86-400-051-7700
INDIA
Yamaha Music India Private
Limited
Spazedge Building, Ground Floor,
Tower A, Sector-47,
Gurgaon- Sohna Road,
Gurgaon-122002, Haryana, India
Tel: +91-124-485-3300
INDONESIA
PT. Yamaha Musik Indonesia
(Distributor)
Yamaha Music Center Bldg. Jalan
Jend. Gatot Subroto Kav. 4,
Jakarta 12930, Indonesia
Tel: +62-21-520-2577
KOREA
Yamaha Music Korea Ltd.
8F, Dongsung Bldg. 21,
Teheran-ro 87-gil, Gangnam-gu,
Seoul, 135-880, Korea
Tel: +82-2-3467-3300
MALAYSIA
Yamaha Music (Malaysia) Sdn. Bhd.
No.8, Jalan Perbandaran,
Kelana Jaya, 47301
Petaling Jaya, Selangor, Malaysia
Tel: +60-3-78030900
SINGAPORE
Yamaha Music (Asia) Private
Limited
Block 202 Hougang Street 21,
#02-00, Singapore 530202,
Singapore
Tel: +65-6740-9200
TAIWAN
Yamaha Music & Electronics
Taiwan Co.,Ltd.
2F., No.1, Yuandong Rd. Banqiao Dist.
New Taipei City 22063, Taiwan
Tel: +886-2-7741-8888
THAILAND
Siam Music Yamaha Co., Ltd.
3, 4, 15, 16th Fl.,
Siam Motors Building,
891/1 Rama 1 Road, Wangmai,
Pathumwan, Bangkok 10330,
Thailand
Tel: +66-2215-2622
VIETNAM
Yamaha Music Vietnam
Company Limited
15th Floor, Nam A Bank Tower,
201-203 Cach Mang Thang Tam St.,
Ward 4, Dist.3,
Ho Chi Minh City, Vietnam
Tel: +84-8-3818-1122
OTHER ASIAN COUNTRIES
Yam aha C orp ora tio n
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku,
Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street,
Southbank,
Vic. 3006, Australia
Tel: +61-3-9693-5111
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC
OCEAN
Yam aha C orp ora tio n
Sales & Marketing Division
10-1, Nakazawa-cho, Naka-ku,
Hamamatsu,
Japan 430-8650
Tel: +81-53-460-2312
AFRICA
MIDDLE EAST
ASIA
OCEANIA
HEAD OFFICE Yamaha Corporation, Audio Products Sales and Marketing Division
10-1, Nakazawa-cho, Naka-ku, Hamamatsu, Japan 430-8650
PA41
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Yamaha NY64 Instrukcja obsługi

Typ
Instrukcja obsługi
Niniejsza instrukcja jest również odpowiednia dla