Whirlpool KN3G620SA(W)/U instrukcja

Marka: Whirlpool

Model: KN3G620SA(W)/U

Kategoria: Mikrofale

Typ: instrukcja

COOKER AND OVEN

Contents

Installation, 2-5

Positioning and levelling

Electrical connection

Gas connection

Adapting to different types of gas

Table of burner and nozzle specifications

Table of characteristics

Description of the appliance, 6

Overall view

Control panel

Start-up and use, 7-12

Using the hob

Using the oven

Cooking modes

Practical advice on using the electric hotplates

Practical cooking advice

Electronic timer

Planning cooking with the electronic programmer

Oven cooking advice table

Precautions and tips, 13

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 14

Switching the appliance off

Cleaning the appliance

Replacing the oven light bulb

Gas tap maintenance

Assistance

Operating Instructions

English, 1

KN3M6SA/U

KN3G65SA/U

KN3G66SA/U

KN3G62SA/U

KN3G6SA/U

KN3G60SA/U

KN3G610SA/U

KN3G620SA/U

KN3G650SA/U

KN3G660SA/U

Polski, 15

Latviešu, 43

Lietuviu;29

Eesti keeles,57

E E

L T

! Before operating your new appliance please read this

instruction booklet carefully. It contains important

information concerning the safe installation and

operation of the appliance.

! Please keep these operating instructions for future

reference. Make sure that the instructions are kept with

the appliance if it is sold, given away or moved.

! The appliance must be installed by a qualified

professional according to the instructions provided.

! Any necessary adjustment or maintenance must be

performed after the cooker has been disconnected

from the electricity supply.

Room ventilation

The appliance may only be installed in permanently-

ventilated rooms, according to current national

legislation. The room in which the appliance is

installed must be ventilated adequately so as to

provide as much air as is needed by the normal gas

combustion process (the flow of air must not be lower

than 2 m

/h per kW of installed power).

The air inlets, protected by grilles, should have a duct

with an inner cross section of at least 100 cm

and

should be positioned so that they are not liable to

even partial obstruction (

see figure A

These inlets should be enlarged by 100% - with a

minimum of 200 cm

- whenever the surface of the hob

is not equipped with a flame failure safety device.

When the flow of air is provided in an indirect manner

from adjacent rooms (

see figure B

), provided that

these are not communal parts of a building, areas with

increased fire hazards or bedrooms, the inlets should

be fitted with a ventilation duct leading outside as

described above.

! After prolonged use of the appliance, it is advisable to

open a window or increase the speed of any fans used.

Disposing of combustion fumes

The disposal of combustion fumes should be

guaranteed using a hood connected to a safe and

efficient natural suction chimney, or using an electric

fan that begins to operate automatically every time the

appliance is switched on (

see figure

! The liquefied petroleum gases are heavier than air

and collect by the floor, therefore all rooms containing

LPG cylinders must have openings leading outside so

that any leaked gas can escape easily.

LPG cylinders, therefore, whether partially or

completely full, must not be installed or stored in

rooms or storage areas that are below ground level

(cellars, etc.). Only the cylinder being used should be

stored in the room; this should also be kept well away

from sources of heat (ovens, chimneys, stoves) that

may cause the temperature of the cylinder to rise

above 50°C.

Positioning and levelling

! It is possible to install the appliance alongside

cupboards whose height does not exceed that of the

hob surface.

! Make sure that the wall in contact with the back of

the appliance is made from a non-flammable, heat-

resistant material (T 90°C).

To install the appliance correctly:

• Place it in the kitchen, dining room or the bed-sit

(not in the bathroom).

• If the top of the hob is higher than the cupboards,

the appliance must be installed at least 200 mm

away from them.

• If the cooker is installed underneath a wall cabinet,

there must be a minimum distance of 420 mm

between this cabinet and the top of the hob.

Installation

Adjacent room Room requiring

ventilation

Ventilation opening for

comburent air

Increase in the gap

between the door and

the flooring

Fumes channelled

straight outside

Fumes channelled through a

chimney or a branched flue

system (reserved for cooking

appliances)

• If the cooker is

installed underneath a

wall cabinet, there must

be a minimum distance

of 420 mm between this

cabinet and the top of

the hob.

This distance should be

increased to 700 mm if

the wall cabinets are

flammable (

see figure

• Do not position blinds behind the cooker or less

than 200 mm away from its sides.

• Any hoods must be installed according to the

instructions listed in the relevant operating manual.

Levelling

If it is necessary to level the

appliance, screw the adjustable

feet into the places provided on

each corner of the base of the

cooker (

see figure

The legs* fit into the slots on

the underside of the base of

the cooker.

Electrical connection

Install a standardised plug corresponding to the load

indicated on the appliance data plate (

see Technical

data table

The appliance must be directly connected to the

mains using an omnipolar circuit-breaker with a

minimum contact opening of 3 mm installed between

the appliance and the mains. The circuit-breaker must

be suitable for the charge indicated and must comply

with NFC 15-100 regulations (the earthing wire must

not be interrupted by the circuit-breaker). The supply

cable must be positioned so that it does not come into

contact with temperatures higher than 50°C at any

point.

Before connecting the appliance to the power supply,

make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated by the data plate.

HOOD

420

Min.

min. 650 mm. with hood

min.

700 mm. without hood

mm.

600

Min. mm.

420

Min. mm.

• The voltage is in the range between the values

indicated on the data plate.

• The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced

by authorised technicians only.

! The manufacturer declines any liability should

these safety measures not be observed.

Gas connection

Connection to the gas network or to the gas cylinder

may be carried out using a flexible rubber or steel hose,

in accordance with current national legislation and after

making sure that the appliance is suited to the type of

gas with which it will be supplied (see the rating sticker

on the cover: if this is not the case

see below

). When

using liquid gas from a cylinder, install a pressure

regulator which complies with current national

regulations. To make connection easier, the gas supply

may be turned sideways*: reverse the position of the

hose holder with that of the cap and replace the gasket

that is supplied with the appliance.

! Check that the pressure of the gas supply is

consistent with the values indicated in the Table of

burner and nozzle specifications (

see below

). This will

ensure the safe operation and durability of your

appliance while maintaining efficient energy

consumption.

Gas connection using a flexible rubber hose

Make sure that the hose complies with current

national legislation. The internal diameter of the hose

must measure: 8 mm for liquid gas supply; 13 mm for

methane gas supply.

Once the connection has been performed, make sure

that the hose:

• Does not come into contact with any parts that

reach temperatures of over 50°C.

• Is not subject to any pulling or twisting forces and

that it is not kinked or bent.

• Does not come into contact with blades, sharp

corners or moving parts and that it is not

compressed.

• Is easy to inspect along its whole length so that its

condition may be checked.

• Is shorter than 1500 mm.

• Fits firmly into place at both ends, where it will be

fixed using clamps that comply with current

regulations.

! If one or more of these conditions is not fulfilled or if

the cooker must be installed according to the

conditions listed for class 2 - subclass 1 appliances

(installed between two cupboards), the flexible steel

hose must be used instead (

see below

Connecting a flexible jointless stainless steel pipe

to a threaded attachment

Make sure that the hose and gaskets comply with

current national legislation.

To begin using the hose, remove the hose holder on

the appliance (the gas supply inlet on the appliance is

a cylindrical threaded 1/2 gas male attachment).

! Perform the connection in such a way that the hose

length does not exceed a maximum of 2 metres,

making sure that the hose is not compressed and

does not come into contact with moving parts.

Checking the tightness of the connection

When the installation process is complete, check the

hose fittings for leaks using a soapy solution. Never

use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a

7 mm socket spanner (

see

figure

), and replace them with

nozzles suited to the new type

of gas (

see Burner and nozzle

specifications table

3. Replace all the components

by following the above

instructions in reverse.

Adjusting the hob burners’ minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory screw,

which is positioned inside or next to the tap pin, until

the flame is small but steady.

! If the appliance is connected to a liquid gas supply,

the regulatory screw must be fastened as tightly as

possible.

3. While the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame is not extinguished.

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used with a

different type of gas, replace the old rating label with a new

one that corresponds to the new type of gas (these labels

are available from Authorised Technical Assistance

Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating to

“regulators for channelled gas”.

Table of burner and nozzle specifications

Table 1 G30 (GPB-B) G20 (GZ50) G2.350 (GZ35)

Burner Diameter

(mm)

Thermal

power

(p.c.s.*)

Thermal

power

(p.c.s.*)

By-pass

1/100

Nozzle

1/100

Flow*

g/h

Thermal

power

(p.c.s.*)

Nozzle

1/100

Flow*

l/h

Thermal

power

(p.c.s.*)

Nozzle

1/100

Flow*

l/h

Reduc. Nominal (mm) (mm) Nominal (mm) Nominal (mm)

Fast (Large)(R) 100 0,70 3,40 41 87 247 3,00 128 286 3,00 158 397

Semi Fast

(Medium) (S)

75 0,40 2,20 30 70 160 1,90 104 181 1,90 143 251

Auxiliary (Small)

(A)

51 0,40 1,30 30 52 95 1,00 76 95 1,00 106 132

Supply

Pressures

Minimum (mbar)

Nominal (mbar)

Maximum (mbar)

* A 15°C e 1013 mbar-dry gas

G2.350 (GZ35) p.c.s. 27.20 MJ/m³

G20 (GZ50) p.c.s. 37,78 MJ/m³

G30 (GPB-B) p.c.s. 49,47 MJ/Kg

Ø180

TABLE OF CHARACTERISTSICS

Dimensions (with

drawn guide rails)

width 44 cm

height 34 cm

depth 38 cm

Volume (with

drawn guide rails)

54 l

Dimensions of the

lower compartment

width 42 cm

height 23 cm

depth 44 cm

Burners

may be adapted for use with any type

of gas shown on the data plate, which

is located inside the flap or, after the

oven compartment has been opened,

on the left-hand wall inside the oven.

Voltage and

frequency

see data plate

ENERGY LABEL

Directive 2002/40/EC on the label of

electric ovens.

Standard EN 50304

Energy consumption for Natural

convection – heating mode:

Convection;

Declared energy consumption for

Forced convection Class – heating

mode: Baking

This appliance conforms to the

following European Economic

Community directives: 2006/95/EC

dated 12/12/06 (Low Voltage) and

subsequent amendments -

2004/108/EC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments - 93/68/EEC

dated 22/07/93 and subsequent

amendments.

2002/96/EC

2009/142 of 30/11/09 (Gas)

1275/2008 (Stand-by/ Off mode)

KN3G65SA/U

KN3G66SA/U

KN3G62SA/U

KN3G6SA/U

KN3G60SA/U

KN3G610SA/U

KN3G620SA/U

KN3G650SA/U

KN3G660SA/U

KN3M6SA/U

Description

of the appliance

Overall view

Control panel

Only available in certain models.

BURNER

control knobs

SELECTOR

knob

THERMOSTAT

knob

THERMOSTAT

indicator light

GAS BURNER

ignition button*

TIMER button*

BURNER

control knobs

THERMOSTAT

indicator light

SELECTOR

knob

THERMOSTAT

knob

TIMER

BURNER

control knobs

SELECTOR

knob

THERMOSTAT

knob

THERMOSTAT

indicator light

TIMER

button

Electronic

timer*

BURNER

control knobs

SELECTOR

knob

THERMOSTAT

indicator light

THERMOSTAT

knob

Electronic

cooking

programmer*

TIMER

button

COOKING

END TIME

button

COOKING

TIME button

BURNER

control knobs

SELECTOR

knob

THERMOSTAT

knob

THERMOSTAT

indicator light

ACTIVE HOTPLATE

indicator light*

GAS BURNER

ignition button*

ELECTRIC

HOTPLATE

control knob*

ELECTRIC HOTPLATE

Hob grid

Control panel

GRILL

GUIDE RAILS

for the sliding racks

position 3

position 2

position 1

Gas burner

Containment surface

for spills

Adjustable foot

position 5

position 4

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a full ring showing

the strength of the flame for the relevant burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an

anticlockwise direction so that it is pointing to the

maximum flame setting E .

3. Adjust the intensity of the flame to the desired

level by turning the BURNER knob in an

anticlockwise direction. This may be the minimum

setting C , the maximum setting E or any position in

between the two.

If the appliance is fitted with

an electronic lighting

device* (

), press the

BURNER knob and turn it in

an anticlockwise direction,

towards the minimum flame

setting, until the burner is lit.

The burner may be

extinguished when the knob is released. If this

occurs, repeat the operation, holding the knob down

for a longer period of time.

f the appliance is equipped with a flame failure

safety device (X), press and hold the BURNER knob

for approximately 3-7 seconds to keep the flame

alight and to activate the device.

! If the flame is accidentally extinguished, switch off

the burner and wait for at least 1 minute before

attempting to relight it.

To switch the burner off, turn the knob until it

reaches the stop position •.

Electric hotplates

The corresponding knob may be turned clockwise or

anti-clockwise and set to any of the six different

positions:

Setting Normal or Fast Plate

0 Off

1 Low

2 - 5 Medium

High

When the selector knob is in any position other than

the off position, the ‘on’ light is illuminated.

Practical advice on using the burners

For the burners to work in the most efficient way

possible and to save on the amount of gas

consumed, it is recommended that only pans that

have a lid and a flat base are used. They should

also be suited to the size of the burner:

Burner ø Cookware diameter (cm

)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

To identify the type of burner, please refer to the

diagrams contained in the “Burner and nozzle

specifications”.

Using the oven

! The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective

substances used during the manufacturing process

burning away.

! Before operating the product, remove all plastic

film from the sides of the appliance.

! Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged.

! Should the appliance be equipped with an

electronic programmer*, to use the electric oven, just

press buttons

and at the same time (the

symbol will appear on the display) before

selecting the desired cooking function.

1. Select the desired cooking mode by turning the

SELECTOR knob.

2. Select the recommended temperature for the

cooking mode or the desired temperature by turning

the THERMOSTAT knob.

A list detailing cooking modes and suggested

cooking temperatures can be found in the relevant

table (

see Oven cooking advice table

During cooking it is always possible to:

• Change the cooking mode by turning the

SELECTOR knob.

• Change the temperature by turning the

THERMOSTAT knob.

Only available in certain models.

cod, Ancona style stockfish, tender veal strips with

rice, etc. Excellent results are achieved when

preparing veal or beef-based dishes as well (braised

meats, stew, goulash, wild game, ham etc.) which

need to cook slowly and require basting or the

addition of liquid. It nonetheless remains the best

system for baking cakes as well as fruit and cooking

using covered casserole dishes for oven baking.

When cooking in convection mode, only use one

dripping pan or cooking rack at a time, otherwise the

heat distribution will be uneven. Using the different

rack heights available, you can balance the amount

of heat between the top and the bottom of the oven.

Select from among the various rack heights based

on whether the dish needs more or less heat from

the top.

FAN ASSISTEDFAN ASSISTED

FAN ASSISTED mode

Temperature: any temperature between 50°C and Max.

The heating elements, as well as the fan, will come

on. Since the heat remains constant and uniform

throughout the oven, the air cooks and browns food

uniformly over its entire surface. With this mode, you

can also cook various dishes at the same time, as

long as their respective cooking temperatures are

the same. A maximum of 2 racks can be used at the

same time, following the instructions in the section

entitled: “Cooking On More Than One Rack”.

This fan assisted mode is particularly recommended

for dishes requiring a gratin finish or for those

requiring considerably prolonged cooking times,

such as for example: lasagne, pasta bakes, roast

chicken and potatoes, etc… Moreover, the excellent

heat distribution makes it possible to use lower

temperatures when cooking roasts. This results in

less loss of juices, meat which is more tender and a

decrease in the loss of weight for the roast. The fan

assisted mode is especially suited for cooking fish,

which can be prepared with the addition of a limited

amount of condiments, thus maintaining their

flavour and appearance.

Desserts: the fan assisted mode is also perfect for

baking leavened cakes.

Moreover, this mode can also be used to thaw

quickly white or red meat and bread by setting the

temperature to 80 °C. To thaw more delicate foods,

set the thermostat to 60°C or use only the cold air

circulation feature by setting the thermostat to 0°C.

TOP OVEN TOP OVEN

TOP OVEN

mode

Temperature: any temperature between 50°C and

Max.

The top heating element comes on.

This mode can be used to brown food at the end of

cooking.

• Stop cooking by turning the SELECTOR knob to

the “0” position.

! Always place cookware on the rack(s) provided.

THERMOSTAT indicator light

When this is illuminated, the oven is generating

heat. It switches off when the inside of the oven

reaches the selected temperature. At this point the

light illuminates and switches off alternately,

indicating that the thermostat is working and is

maintaining the temperature at a constant level.

Oven light

This is switched on by turning the SELECTOR knob

to any position other than “0”. It remains lit as long

as the oven is operating. By selecting

with the

knob, the light is switched on without any of the

heating elements being activated.

Timer*

To activate the Timer proceed as follows:

1. Turn the TIMER knob in a clockwise direction 4

for almost one complete revolution to set the buzzer.

2. Turn the TIMER knob in an anticlockwise direction

5 to set the desired length of time.

Cooking modes

BAKING BAKING

BAKING mode

Temperature: any temperature between 50°C and Max.

The rear heating element and the fan come on,

guaranteeing delicate heat distributed uniformly

throughout the oven.

This mode is ideal for baking and cooking delicate

foods - especially cakes that need to rise - and for

the preparation of certain tartlets on 3 shelves at the

same time. Here are a few examples: cream puffs,

sweet and savoury biscuits, savoury puffs, Swiss

rolls and small portions of vegetables au gratin,

etc…..

CONVECTION CONVECTION

CONVECTION mode

Temperature: any temperature between 50°C and Max.

On this setting, the top and bottom heating

elements come on. This is the classic, traditional

type of oven which has been perfected, with

exceptional heat distribution and reduced energy

consumption. The convection oven is still unequalled

when it comes to cooking dishes made up of several

ingredients, e.g. cabbage with ribs, Spanish style

Only available in certain models.

and insert the spit in the hole provided on the back

panel of the oven.

3. Activate the rotisserie by selecting

with the

SELECTOR knob.

Lower oven compartment

There is a compartment

underneath the oven

that may be used to

storeoven accessories or

deep dishes. To open

the door pull it

downwards (

see

figure

! Do not place flammable materials in the lower oven

compartment.

! The internal surfaces of the compartment (where

present) may become hot.

Practical advice on using the electric

hotplates

To avoid heat loss and damage to the hotplates use

pans with a flat base, whose diameter is no less

than that of the hotplate itself.

Setting Normal or Fast Plate

0 Off

1 Cooking vegetables, fish

Cooking potatoes (using steam) soups,

chickpeas, beans.

Continuing the cooking of large quantities

of food, minestrone

For roasting (average)

For roasting (above average)

For browning and reaching a boil in a

short time.

! Before using the hotplates for the first time, you

should heat them at maximum temperature for

approximately 4 minutes, without placing any pans

on them. During this initial stage, their protective

coating hardens and reaches its maximum

resistance.

GRILLGRILL

GRILL

mode

Temperature: any temperature between 50°C and Max.

The top heating element and the turnspit come on.

The extremely high and direct temperature of the grill

makes it possible to brown the surface of meats and

roasts while locking in the juices to keep them

tender. The grill is also highly recommended for

dishes that require a high temperature on the

surface: such as beef steaks, veal, rib steak, filets,

hamburgers etc...

Always leave the oven door ajar during cooking,

except when using the turnspit.

Some grilling examples are included in the “Practical

Cooking Advice” paragraph..

FAN ASSISTED GRILL

mode

Temperature: any temperature between 50°C and 200°C.

The top central heating element and the fan come on.

This combination of features increases the

effectiveness of the unidirectional thermal radiation of

the heating elements through forced circulation of the

air throughout the oven. This helps prevent food from

burning on the surface, allowing the heat to penetrate

right into the food. Excellent results are achieved

with kebabs made with meats and vegetables,

sausages, ribs, lamb chops, chicken in a spicy

sauce, quail, pork chops, etc.

This mode is also ideal for cooking fish steaks, like

swordfish, tuna, grouper, stuffed cuttlefish etc.

! The TOP OVEN, GRILL and FAN ASSISTED GRILL

cooking modes must be performed with the oven

door shut.

! When using the TOP OVEN and GRILL cooking

modes, place the rack in position 5 and the dripping

pan in position 1 to collect cooking residues (fat and/

or grease). When using the FAN ASSISTED GRILL

cooking mode, place the rack in position 2 or 3 and

the dripping pan in position 1 to collect cooking

residues.

Rotisserie*

To activate the

rotisserie function (

see

diagram

) proceed as

follows:

1. Place the dripping

pan in position 1.

2. Place the rotisserie

support in position 4

Only available in certain models.

Planning cooking with the electronic

programmer*

Setting the clock

After the appliance has been connected to the

power supply, or after a blackout, the display will

automatically reset to 0:00 and begin to blink. To set

the time:

1. Press the COOKING TIME button and the

COOKING END TIME

simultaneously.

2. Within 4 seconds of having pressed these

buttons, set the exact time by pressing the + and -

buttons. The + button advances the hours and the

button decreases the hours.

Once the time has been set, the programmer

automatically switches to manual mode.

Setting the timer

The timer enables a countdown to be set, when the

time has elapsed a buzzer sounds.

To set the timer proceed as follows:

1. press the TIMER button

. The display shows:

Practical cooking advice

Cooking on several shelves simultaneously

If it is necessary to use two racks, use the FAN

ASSITED mode

, as this is the only cooking mode

suited to this type of cooking. We also recommend

that:

• Positions 1 and 5 are not used. This is because

excessive direct heat can burn temperature

sensitive foods.

• Positions 2 and 4 are used and that food that

requires more heat is placed on the rack in

position 2.

• When cooking foods that require different cooking

times and temperatures, set a temperature that is

halfway between the two recommended

temperatures (

see Oven cooking advice table

)

and place the more delicate food on the rack in

position 4. Remove the food that requires a

shorter cooking time first.

• When cooking pizzas on several racks with the

temperature set to 220°C, the oven is preheated

for 15 minutes. Generally speaking, cooking on

the rack in position 4 takes longer: we

recommend that the pizza cooked on the lowest

rack position is removed first, followed by the

pizza cooked in position 4 a few minutes later.

• Place the dripping pan on the bottom and the rack

on top.

Electronic timer*

This function displays the time and works as a timer

which counts down to zero.

! All functions will be implemented approximately 7

seconds after they have been set.

Resetting the clock

After the appliance has been connected to the

power supply, or after a power cut, the clock display

will begin to blink, showing the figure:

0:000:00

0:00

• Press button

and then buttons

and

to set

the exact time. Press and hold the buttons to

quicken the count upwards.

Any necessary modifications can be made by

repeating the above process.

Timer feature

This function may be accessed by pressing the

button, after which the display will show the symbol

n. Every time the + button is pressed it

corresponds to a time increase of 10 seconds, until

it reaches 99 minutes and 50 seconds. After this

point, each press of the button represents an

Pressing the - button reduces the time.

After the time period has been set, the timer will

begin to count down. When the timer reaches zero,

the buzzer will sound (this may be stopped by

pressing any button).

The time may be displayed by pressing the

button, and the

n symbol indicates that the timer

function has been set. After approximately 7 seconds,

the display will automatically revert to the timer.

Cancelling a time that has already been set

Press the - button until the display shows

0:00.0:00.

0:00.

Adjusting the buzzer volume

After selecting and confirming the clock settings,

use the - button to adjust the volume of the alarm

buzzer.

Setting the cooking time with an immediate start

Follow the above procedure for setting the cooking

time (points 1-3).

! When the letter A appears, this indicates that both

the cooking time and the end cooking time have

been programmed in AUTO mode. To restore the

oven to manual operation, after each AUTO cooking

mode press the COOKING TIME and END

COOKING TIME

buttons simultaneously.

! The symbol

will remain lit, along with the oven,

for the entire duration of the cooking programme.

The set cooking duration can be displayed at any

time by pressing the COOKING TIME button

and the cooking end time may be displayed by

pressing the END COOKING TIME button

When the cooking time has elapsed a buzzer

sounds. To stop it, press any button apart from the

+ and - buttons.

End-cooking Timer *

1. To set the buzzer, turn the COOKING TIMER knob

clockwise almost one complete revolution.

2. Turn the knob anticlockwise to set the desired

time: align the minutes shown on the COOKING

TIMER knob with the indicator on the control panel.

3. When the selected time has elapsed, a buzzer

sounds and the oven turns off.

4. When the oven is off the cooking timer can be

used as a normal timer.

! To use the oven manually, in other words when you

do not wish to use the end of cooking timer, turn the

COOKING TIMER knob until it reaches the 9

symbol.

Only available in certain models.

2. Press the + and - buttons to set the desired time.

3. When the buttons are released the timer begins

counting down and the current time appears on the

display.

4. After the time has elapsed a buzzer will sound,

and this can be switched off by pressing any button

(except the + and - buttons). The symbol

will

switch off.

The timer does not switch the oven on or off.

use the - button to adjust the volume of the alarm

buzzer.

Setting the cooking time with a delayed start

First decide which cooking mode you wish to use

and set a suitable temperature using the SELECTOR

and THERMOSTAT knobs on the oven.

1. Press the COOKING TIME button

2. Within 4 seconds of having pressed this button,

set the desired amount of time by pressing the + and

- buttons. If, for example, you wish to set a cooking

3. 4 seconds after the buttons are released, the

current time (for example 10.00) reappears on the

display with the symbol

and the letter A (AUTO).

Next the desired cooking end time must be set:

4. Press the END COOKING TIME button .

5. Within 4 seconds of having pressed this button,

adjust the cooking end time by pressing the + and -

buttons. If, for example, you want cooking to end at

13.00, the display shows:

6. 4 seconds after the buttons are released, the

current time (for example 10.00) reappears on the

display with the letter A (AUTO).

At this point, the oven is programmed to switch on

automatically at 12:30 and switch off after 30

minutes, at 13.00.

Cancelling a previously set cooking programme

Press the COOKING TIME button

and the

COOKING END TIME simultaneously.

Correcting or cancelling previously set data

The data entered can be changed at any time by

pressing the corresponding button (TIMER,

COOKING TIME or COOKING END TIME) and the +

or - button.

When the cooking time data is cancelled, the

cooking end time data is also cancelled

automatically, and vice versa.

If the oven has already been programmed, it will not

accept cooking end times which are before the start

of the programmed cooking process.

Oven cooking advice table

Selector knob

se ttin g

Food to be cooked Weight

(in kg )

Cooking rack

position from

b o tto m

Preheating time

(m inutes)

Therm ostat

knob

se ttin g

Cooking

tim e

(m inu te s)

Baking

Tarts

Fruit cakes

Plum cake

Sponge cake

Stuffed pancakes (on 2

racks)

Small cakes (on 2 racks)

Cheese puffs (on 2

racks)

Cream puffs (on 3 racks)

Biscuits (on 3 racks)

Meringues (on 3 racks)

0.5

0.7

0.5

1.2

0.6

0.4

0.7

0.5

2/3

2-4

1-3-5

180

160

200

190

210

180

20-30

40-45

40-50

25-30

30-35

20-25

15-20

20-25

180

Convection

Duck

Roast veal or beef

P ork roast

B iscu its (sho rt p astry)

Tarts

200

180

65-75

70-75

70-80

15-20

30-35

Fan assisted

Pizza (on 2 racks)

Lasagne

Lamb

Roast chicken +

potatoes Mackerel

Plum-cake

Cream puffs (on 2 racks)

Biscuits (on 2 racks)

Sponge cake (on 1 rack)

Sponge cake (on 2

racks)

Savoury pies

0.5

1.0

1.5

2-4

220

200

180

170

190

180

170

200

15-20

30-35

50-60

60-75

30-35

40-50

20-25

10-15

15-20

20-25

25-30

Top Oven

Browning food to perfect

cooking

- 3/4 15 220 -

Grill

Soles and cuttlefish

Squid and prawn

kebabs

Cod filet

Grilled vegetables

Veal steak

Cutlets

Hamburgers

Mackerels

Toasted sandwiches

n.° 4

3/4

Max

8-10

6-8

10-15

15-20

7-10

15-20

2-3

Fan assisted

grill

Grilled chicken

C u ttle fis h

1.5

200

55-60

30-35

! cooking times are approximate and may vary according to personal taste. When cooking using the grill or fan

assisted grill, the dripping pan must always be placed on the 1st oven rack from the bottom.

Using the cooking timer

1. To set the buzzer, turn the COOKING TIMER knob

clockwise almost one complete revolution.

2. Turn the knob anticlockwise to set the desired

time: align the minutes shown on the COOKING

TIMER knob with the indicator on the control panel.

3. When the selected time has elapsed, a buzzer

sounds and the oven turns off.

4. When the oven is off the cooking timer can be

used as a normal timer.

! To use the oven manually, in other words when

you do not wish to use the end of cooking timer,

turn the COOKING TIMER knob until it reaches the

symbol.

Precautions and tips

! This appliance has been designed and manufactured in

compliance with international safety standards.

The following warnings are provided for safety reasons

and must be read carefully.

General safety

• The appliance was designed for domestic use inside

the home and is not intended for commercial or

industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• Do not touch the appliance with bare feet or with wet or

damp hands and feet.

• The appliance must be used by adults only for the

preparation of food, in accordance with the instructions

provided in this booklet.

• The instruction booklet accompanies a class 1

(insulated) or class 2 - subclass 1 (recessed between 2

cupboards) appliance.

• Keep children away from the oven.

• Make sure that the power supply cables of other

electrical appliances do not come into contact with the

hot parts of the oven.

• The openings used for the ventilation and dispersion of

heat must never be covered.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use flammable liquids (alcohol, petrol, etc...)

near the appliance while it is in use.

• Do not place flammable material in the lower storage

compartment or in the oven itself. If the appliance is

switched on accidentally, it could catch fire.

• Always make sure the knobs are in the “

•” position

when the appliance is not in use.

• When unplugging the appliance, always pull the plug from

the mains socket; do not pull on the cable.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from the

electricity mains.

• If the appliance breaks down, under no circumstances

should you attempt to repair the appliance yourself.

Repairs carried out by inexperienced persons may

cause injury or further malfunctioning of the appliance.

Contact Assistance.

• Do not rest heavy objects on the open oven door.

•

The appliance should not be operated by people

(including children) with reduced physical, sensory or

mental capacities, by inexperienced individuals or by

anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by

someone who assumes responsibility for their safety or

receive preliminary instructions relating to the operation

of the appliance.

WARNING! The glass lid can break in

if it is heated up. Turn off all the burn-

ers and the electric plates before clos-

ing the lid

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing potential

damage to the atmosphere and to public health. The

crossed-out dustbin is marked on all products to

remind the owner of their obligations regarding

separated waste collection. For more information

relating to the correct disposal of household

appliances, owners should contact their local

authorities or appliance dealer.

Respecting and conserving the environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of the

morning.

• Always keep the oven door closed when using the

GRILL and FAN-ASSISTED GRILL mode cooking. This

will achieve better results while saving energy

(approximately 10%).

• Check the door seals regularly and wipe them clean to

ensure they are free of debris so that they adhere

properly to the door, thus avoiding heat dispersion.

Switching the appliance off

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Cleaning the appliance

! Never use steam cleaners or pressure cleaners on

the appliance.

• The stainless steel or enamel-coated external

parts and the rubber seals may be cleaned using

a sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for

the removal of stubborn stains. After cleaning,

rinse well and dry thoroughly. Do not use abrasive

powders or corrosive substances.

• The hob grids, burner caps, flame spreader rings

and burners may be removed to make cleaning

easier; wash them in hot water and non-abrasive

detergent, making sure all burnt-on residue is

removed before drying them thoroughly.

• For hobs with electronic ignition, the terminal part

of the electronic lighting devices should be

cleaned frequently and the gas outlet holes

should be checked for blockages.

• The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot

water and detergent, then rinse well and dry with

a soft cloth. Do not use abrasive products.

•

Clean the glass part of the oven door using a

sponge and a non-abrasive cleaning product,

then dry thoroughly with a soft cloth. Do not use

rough abrasive material or sharp metal scrapers

as these could scratch the surface and cause the

glass to crack.

• The accessories can be washed like everyday

crockery, and are even dishwasher safe.

The cover*

If the cooker is fitted with

a glass cover, this cover

should be cleaned using

lukewarm water. Do not

use abrasive products.

It is possible to remove

the cover in order to

make cleaning the area

behind the hob easier.

Open the cover fully and pull it upwards (

see figure

! Do not close the cover when the burners are alight

or when they are still hot.

! Remove any liquid from the lid before opening it.

Inspecting the oven seals

Check the door seals around the oven regularly. If

the seals are damaged, please contact your nearest

Authorised After-sales Service Centre. We

recommend that the oven is not used until the seals

have been replaced.

Replacing the oven light bulb

1. After disconnecting the oven

from the electricity mains, remove

the glass lid covering the lamp

socket (

see figure

2. Remove the light bulb and

replace it with a similar one:

voltage 230 V, wattage 25 W, cap

E 14.

3. Replace the lid and reconnect the oven to the

electricity supply.

Gas tap maintenance

Over time, the taps may become jammed or difficult to

turn. If this occurs, the tap must be replaced.

! This procedure must be performed by a qualified

technician who has been authorised by the

manufacturer.

Assistance

Please have the following information to hand:

• The appliance model (Mod.).

• The serial number (S/N).

This information can be found on the data plate

located on the appliance and/or on the packaging.

Care and maintenance

Only available in certain models.

Instalacja 16-19

Ustawienie

Pod∏àczenie do instalacji elektrycznej

Pod∏àczenie gazu do kuchni

Dostosowanie kuchni do innych rodzajów gazów

Dane techniczne

Parametry dysz i palników

Opis kuchni 20

Ogólny widok

Panel kontrolny

Uruchomienie i obs∏uga kuchni 21-26

Obs∏uga p∏yty gazowej

Obs∏uga piekarnika

Programy pieczenia

Wskazówki dotyczàce korzystania

z elektrycznej p∏yty grzewczej

Wskazówki dotyczàce pieczenia

Elektroniczny programator

Programowanie pieczenia

Pieczenie w piekarniku – porady praktyczne

Ârodki ostro˝noÊci i porady 27

Ogólne informacje o bezpieczeƒstwie

Pozbywanie si´ starych urzàdzeƒ elektrycznych

Oszcz´dnoÊç energii i ochrona Êrodowiska

Konserwacja i czyszczenie 28

Wy∏àczenie urzàdzenia

Czyszczenie

Wymiana ˝arówki

Smarowanie zaworów gazu

Serwis

Kuchnia z piekarnikiem

Polski, 15

Instrukcja obs∏ugi

LV EE

Latviešu,43

Lietuviu,

Eesti,53

English, 14

KN3M6SA/U

KN3G65SA/U

KN3G66SA/U

KN3G62SA/U

KN3G6SA/U

KN3G60SA/U

KN3G610SA/U

KN3G620SA/U

KN3G650SA/U

KN3G660SA/U

Instalacja

! Przed przystàpieniem do u˝ytkowania urzàdzenia, nale˝y

starannie zapoznaç si´ z podr´cznikiem u˝ytkownika. Za-

wiera on wa˝ne zalecenia dotyczàce bezpieczeƒstwa insta-

lacji, obs∏ugi oraz konserwacji kuchenki. Podr´cznik nale˝y

zachowaç do póêniejszego u˝ytku.

! Instrukcj´ nale˝y zachowaç na przysz∏oÊç. Instrukcja mu-

si byç do∏àczona do urzàdzenia w przypadku sprzeda˝y,

przekazywania innym osobom lub przeprowadzki.

! Poni˝sze instrukcje przeznaczone sà dla wykwalifikowane-

go specjalisty instalujàcego urzàdzenie. Instrukcje te majà

na celu zapewnienie mo˝liwie najbardziej profesjonalnego

i doÊwiadczonego wykonania czynnoÊci zwiàzanych z in-

stalacjà i konserwacjà urzàdzenia.

! Wszelkie prace regulacyjne lub konserwacyjne nale˝y

przeprowadzaç po od∏àczeniu kuchenki od zasilania.

Wentylacja pomieszczenia

Wymagania dla pomieszczeƒ kuchennych

Przed przystàpieniem do instalowania kuchni gazowej

w pomieszczeniu kuchennym itp., nale˝y upewniç si´, czy

spe∏nia ono stawiane mu wymagania. Podstawa prawna,

w oparciu, o którà oceniamy przydatnoÊç pomieszczenia

do zainstalowania w nim kuchni gazowej, jest Rozporzà-

dzenie Ministra Gospodarki Przestrzennej i Budownictwa

z dnia 14 grudnia 1994 r. w sprawie warunków technicz-

nych, jakim powinny odpowiadaç budynki i ich usytuowa-

nie, b´dàce aktem wykonawczym do Prawa budowlanego

(Dz.U. nr 75 z dnia 16-12-2002 poz. 690).

Wa˝ne: niniejsze urzàdzenie mo˝e byç instalowane i wyko-

rzystywane wy∏àcznie w pomieszczeniach z trwa∏à wentyla-

cjà, zgodnie z obowiàzujàcymi przepisami

Pomieszczenie powinno umo˝liwiaç dop∏yw powietrza, któ-

re niezb´dne jest do w∏aÊciwego spalania gazu. Dop∏yw po-

wietrza powinien byç nie mniejszy ni˝ 2 m

/h na jeden kW

mocy palników. Powietrze mo˝e byç dostarczane w wyniku

bezpoÊredniego przep∏ywu z zewnàtrz przez kana∏ o prze-

kroju, co najmniej 100 cm

, którego konstrukcja musi unie-

mo˝liwiaç przypadkowe zablokowanie (Rysunek A). Otwór

ten nale˝y powi´kszyç o 100%, je˝eli instalacja kominowa

nie zosta∏a wyposa˝ona w urzàdzenie bezpieczeƒstwa, wy-

krywajàce ogieƒ. Ewentualnie dop∏yw powietrza mo˝e odby-

waç si´ poÊrednio z sàsiednich pomieszczeƒ, które wypo-

sa˝one sà w kana∏y wentylacyjne wychodzàce na zewnàtrz,

spe∏niajàce wymagania dla kana∏ów opisane powy˝ej.

Wszystko to przy za∏o˝eniu, ˝e sàsiednie pomieszczenia nie

sà pomieszczeniami wspólnymi, sypialniami ani nie wyst´-

puje w nich zagro˝enie po˝arowe (Rysunek B).

! JeÊli kuchnia jest wykorzystywana intensywnie I d∏ugo, to

mo˝e okazaç si´ konieczne otworzenie okna dla poprawie-

nia wentylacji.

Odprowadzanie spalin

Pomieszczenie, w którym ma byç zainstalowana kuchnia

powinno byç wyposa˝one w system wentylacji odprowa-

dzajàcy na zewnàtrz spaliny powstajàce podczas spalania.

Instalacja ta powinna sk∏adaç si´ z okapu lub wentylatora

elektrycznego, który w∏àcza si´ automatycznie za ka˝dym

razem, gdy uruchamiana jest kuchnia.

! Gaz p∏ynny jest ci´˝szy od powietrza i w zwiàzku z tym ma

tendencje do gromadzenia si´ na dolnych poziomach. Po-

koje, w których zainstalowano butle z gazem p∏ynnym, po-

winny byç wyposa˝one w kana∏y wentylacyjne wyprowa-

dzone z pomieszczenia na zewnàtrz, umo˝liwiajàce wydo-

stawanie si´ gazu w przypadku nieszczelnoÊci. Z tego sa-

mego powodu butle z gazem, zarówno puste jak i cz´Êcio-

wo nape∏nione, nie powinny byç ani instalowane, ani prze-

chowywane w pomieszczeniach usytuowanych pod po-

wierzchnià ziemi (piwnice, itp.). Dobrà praktykà jest prze-

chowywanie w pomieszczeniu kuchennym jedynie tego

zbiornika, który jest aktualnie wykorzystywany, pod warun-

kiem, ˝e nie znajduje si´ on zbyt blisko êróde∏ ciep∏a (piecy-

ki, kominki, piekarniki, itp.), które mog∏yby zwi´kszyç tem-

peratur´ we wn´trzu zbiornika powy˝ej 50°C.

Ustawianie i poziomowanie kuchni

Kuchnia gazowa pod wzgl´dem ochrony przed przegrza-

niem otaczajàcych powierzchni jest przyrzàdem klasy X i ja-

ko taka mo˝e byç zabudowana w ciàgu meblowym tylko do

wysokoÊci p∏yty roboczej tj. 850 mm od posadzki. Zabudo-

wa powy˝ej tego poziomu jest zabroniona.

Rysunek A

Przyk∏ady otworów

wentylacyjnych

pomieszczenie

sàsiednie

pomieszczenie, które

ma byç wentylowane

Rysunek B

Powi´kszenie szczeliny

wentylacyjnej pomi´dzy

oknem i pod∏ogà

komin lub rozga∏´ziony

kana∏ dymowy

bezpoÊrednio na zewnàtrz

(w przypadku kuchenek)

Uwaga: Kuchnia w klasie X nie mo˝e byç zabudowana wy-

sokim meblem. Jednak w ka˝dym przypadku meble do za-

budowy muszà mieç ok∏adzin´ oraz klej do jej przyklejenia

odporny na temperatur´ 100°C. Niespe∏nienie tego warun-

ku mo˝e spowodowaç zdeformowanie powierzchni lub od-

klejenia ok∏adziny. Je˝eli nie mamy pewnoÊci, co do odpor-

noÊci termicznej mebli, kuchni´ nale˝y zabudowaç mebla-

mi zachowujàc odst´p ok. 2 cm.

! Âciana znajdujàca si´ za kuchnià powinna byç uodpornio-

na na wysokie temperatury. Podczas korzystania z kuchni, jej

tylna Êciana mo˝e rozgrzaç si´ do temperatury oko∏o 90°C.

W∏aÊciwa instalacja kuchni wymaga uwzgl´dnienia

poni˝szych kwestii:

• Kuchni´ mo˝na zainstalowaç w kuchni, kuchnio-jadalni

lub pokoju spe∏niajàcym warunki techniczne wynikajàce

z przytoczonych przepisów; nie wolno jej instalowaç w ∏a-

zience ani w pomieszczeniu z prysznicem.

• Meble znajdujàce si´ obok kuchni, które wystajà powy˝ej

powierzchni kuchni, powinny znajdowaç si´ w odleg∏oÊci,

co najmniej 200 mm od kraw´dzi p∏yty z palnikami.

• Szafki sàsiadujàce z okapem

powinny znajdowaç si´ w odle-

g∏oÊci, co najmniej 420 mm od

powierzchni kuchni. Minimalna

odleg∏oÊç nad poziomem palni-

ków, w jakiej mogà byç moco-

wane elementy umeblowania

kuchni wykonane z materia∏ów

niezabezpieczonych termicznie

wynosi 700 mm.

• Nie stosowaç zas∏on z ty∏u kuchni i w odleg∏oÊci nie

mniejszej ni˝ 200 mm od jej boków.

• Okapy nale˝y montowaç zgodnie z instrukcjami podany-

mi w do∏àczonych do nich instrukcjach obs∏ugi, ale nie ni-

˝ej ni˝ 650 mm.

Kuchnia ma nast´pujàcà technicznà specyfikacj´:

Kat. II2ELs3B/P

Poziomowanie kuchni

Kuchenka wyposa˝ona jest w nó˝-

ki o zmiennej wysokoÊci umo˝liwia-

jàce odpowiednie wypoziomowa-

nie urzàdzania. JeÊli jest to koniecz-

ne nale˝y wkr´ciç lub wykr´ciç

nó˝ki znajdujàce si´ w naro˝nikach

podstawy kuchenki a˝ do uzyska-

nia w∏aÊciwego wypoziomowania.

Monta˝ nó˝ek (niektóre modele)

Przyrzàd do montowania nó˝ek

w podstawie kuchni

Pod∏àczenie do instalacji elektrycznej

Kuchenki, które wyposa˝one sà w trójbiegunowy kabel za-

silajàcy przystosowane sà do zasilania pràdem zmiennym

o parametrach podanych na tabliczce znamionowej

(umieszczonej we wn´ce pod piekarnikiem).

Uwaga: Do zasilania kuchni nie nale˝y stosowaç trans-

formatorów, przejÊciówek ani boczników, gdy˝ mogà

si´ one nadmiernie nagrzewaç lub zapaliç.

Na kablu zasilajàcym nale˝y zamontowaç standardowà

wtyczk´, odpowiadajàcà maksymalnemu obcià˝eniu, które

podano na tabliczce znamionowej. Ewentualnie, pod∏àczyç

urzàdzenie bezpoÊrednio do instalacji elektrycznej. W tym

przypadku nale˝y dodatkowo zamontowaç jednobiegunowy

wy∏àcznik sieciowy o odleg∏oÊci styków, co najmniej 3 mm

i odpowiadajàcy obowiàzujàcym przepisom bezpieczeƒstwa

(przewód uziemiajàcy nie mo˝e byç roz∏àczany przez wy∏àcz-

nik). Wy∏àcznik ten b´dzie odcina∏ kuchenk´ od zasilania. Ka-

bel zasilajàcy powinien byç u∏o˝ony w taki sposób, aby tem-

peratura w ˝adnym punkcie jego powierzchni nie mog∏a

przekroczyç temperatury pokojowej powi´kszonej o 50°C.

Przed wykonaniem po∏àczenia nale˝y sprawdziç czy:

• Urzàdzenie posiada obwód ochronny i wtyczk´ zgodnà

z obowiàzujàcymi przepisami.

• Bezpiecznik oraz instalacja elektryczna wytrzymajà obcià-

˝enie kuchenki.

• Instalacja elektryczna wyposa˝ona jest w skuteczny sys-

tem uziemiajàcy spe∏niajàcy wymagania aktualnych stan-

dardów i przepisów.

! Wtyczka lub wy∏àcznik sieciowy muszà byç ∏atwo dost´p-

ne po zainstalowaniu kuchenki.

! Przewód zasilajàcy nie mo˝e byç zagi´ty lub przygnieciony.

! Przewód zasilajàcy musi byç regularnie sprawdzany i w ra-

zie usterki wymieniony przez autoryzowanego technika.

! Producent nie ponosi ˝adnej odpowiedzialnoÊci za

ewentualne szkody wynik∏e z niew∏aÊciwego zainsta-

lowania urzàdzenia.

Pod∏àczenie gazu do kuchni

Uwaga: CzynnoÊç ta mo˝e byç wykonana jedynie przez

technika z odpowiednimi uprawnieniami, autoryzowa-

nego przez producenta.

Pod∏àczyç kuchni´ do butli gazowej lub rury instalacji gazo-

wej, przestrzegajàc obowiàzujàcych przepisów, wy∏àcznie po

uprzednim ustaleniu, czy kuchnia mo˝e byç zasilana gazem

wyst´pujàcym w danej instalacji. JeÊli jest inaczej, nale˝y wy-

HOOD

420

Min.

min.

650

mm. with hood

min.

700

mm. without hood

mm.

600

Min. mm.

420

Min. mm.

Klasa 2 podklasa 1

Klasa 1

konaç zalecania podane w cz´Êci „Dostosowywanie kuchen-

ki do ró˝nych rodzajów gazów”. Niektóre modele kuchenki

umo˝liwiajà pod∏àczenie instalacji gazowej z lewej lub prawej

strony kuchenki – aby zmieniç stron´ zasilania nale˝y zamie-

niç po∏o˝enie uchwytu w´˝a i korka zamykajàcego oraz wy-

mieniç uszczelk´ (do∏àczonà do kuchni). W przypadku pod-

∏àczenia do butli z gazem p∏ynnym nale˝y zastosowaç regu-

lator ciÊnienia, spe∏niajàcy obowiàzujàce przepisy.

Wa˝ne: nale˝y sprawdziç czy ciÊnienie gazu w instalacji

zgodne jest z zaleceniami podanymi w tabeli 1 zatytu∏owa-

nej „Parametry dysz i palników”. Zapewni to bezpiecznà

prac´ kuchni, w∏aÊciwe zu˝ycie gazu oraz przed∏u˝y czas

bezawaryjnej pracy kuchni.

Pod∏àczenie do sztywnej instalacji rurowej

(miedzianej lub stalowej)

Pod∏àczenie do instalacji gazowej powinno byç wykonane

w taki sposób, który nie wywo∏uje napr´˝eƒ w ˝adnym

punkcie instalacji ani na ˝adnej cz´Êci urzàdzenia.

Urzàdzenie wyposa˝one jest w regulowanà z∏àczk´

w kszta∏cie litery “L” oraz uszczelk´, które umo˝liwiajà pod-

∏àczenie do instalacji gazowej. Je˝eli zajdzie potrzeba prze-

kr´cenia z∏àczki to wymagana b´dzie równie˝ wymiana

uszczelki (do∏àczonej do urzàdzenia).

Z∏àcze doprowadzajàce gaz do kuchenki to m´ski cylinder

z gwintem 1/2.

Pod∏àczenie do elastycznego przewodu metalowego

Z∏àcze doprowadzajàce gaz do kuchenki to z∏àcze m´skie

z gwintem 1/2 do rur gazowych o przekroju okràg∏ym. Do

pod∏àczenia nale˝y stosowaç wy∏àcznie rury i uszczelki od-

powiadajàce aktualnie obowiàzujàcym normom. Maksy-

malna d∏ugoÊç przewodu elastycznego nie mo˝e przekra-

czaç 2000 mm. Po wykonaniu po∏àczenia nale˝y sprawdziç

czy elastyczny przewód metalowy nie styka si´ z ˝adnymi

cz´Êciami ruchomymi ani czy nie jest niczym przyciÊni´ty.

Pod∏àczenie w´˝em elastycznym

Kuchni´ gazowà pod∏àczamy w´˝em elastycznym tylko

w przypadku zasilania gazem p∏ynnym z butli gazowej.

Do pod∏àczenia nale˝y zastosowaç wà˝ gazowy odpowia-

dajàcy wymaganiom okreÊlonym przez krajowe normy. Je-

Êli kuchenka zasilana jest gazem p∏ynnym nale˝y zastoso-

waç regulatory ciÊnienia, które spe∏niajà krajowe przepisy

techniczne. Wewn´trzna Êrednica w´˝a powinna wynosiç:

• 8 mm, w przypadku zasilania gazem p∏ynnym

Sprawdziç czy wà˝ jest ÊciÊle dopasowany na obu koƒcach.

Do zamocowania w´˝a u˝yç standardowych zacisków,

G∏ównymi postanowienia obowiàzujàcych norm technicz-

nych przewidujà, ˝e:

• wà˝ nie powinien w ˝adnym punkcie stykaç si´ z „goràcy-

mi” elementami kuchenki;

• wà˝ nie powinien byç d∏u˝szy ni˝ 1,5 metra

• wà˝ nie powinien byç w ˝adnym miejscu zgi´ty ani nacià-

gni´ty, na ca∏ej swojej d∏ugoÊci nie powinien równie˝ po-

siadaç ciasnych zakr´tów ani zw´˝eƒ

• na ca∏ej swojej d∏ugoÊci wà˝ powinien byç dost´pny, tak,

aby mo˝liwa by∏a kontrola jego zu˝ycia

• w przypadku wykrycia nieszczelnoÊci wà˝ powinien byç

ca∏kowicie wymieniony; naprawianie nieszczelnego w´˝a

jest zabronione

Sprawdzanie szczelnoÊci

Wa˝ne: Po zakoƒczeniu instalacji kuchenki nale˝y spraw-

dziç szczelnoÊç wszystkich po∏àczeƒ stosujàc do tego wo-

d´ z myd∏em. Do sprawdzania szczelnoÊci nie wolno w ˝ad-

nym wypadku stosowaç ognia!

Dostosowywanie kuchenki

do ró˝nych rodzajów gazów

Aby dostosowaç kuchenk´ do gazu innego rodzaju, ni˝ ro-

dzaj, dla którego zaprojektowano kuchenk´ (patrz naklejka

na spodzie kuchenki lub na opakowaniu), nale˝y wymieniç

dysze palników, zgodnie z poni˝szà procedurà:

1. Zdemontowaç krat´ podpierajàcà garnki i wysunàç pal-

niki z kuchenki

2. Za pomocà klucza nasadowego

7mm odkr´ciç dysze i wymieniç je

na nowe dysze, odpowiednie do

gazu danego typu (patrz Tabela 1,

„Parametry dysz i palników”).

3. Ponownie zmontowaç razem cz´-

Êci, wykonujàc wy˝ej opisane

czynnoÊci w odwrotnej kolejnoÊci

Regulacja dop∏ywu powietrza do palnika

Palniki nie wymagajà takiej regulacji.

Regulacja minimalnej wielkoÊci p∏omienia

1. Ustawiç zawór gazu w po∏o˝eniu najmniejszego p∏omienia

2. Zdemontowaç pokr´t∏o i przekr´ciç Êrub´ regulacyjnà

(znajdujàcà si´ bàdê po jednej ze stron trzonka lub w je-

go Êrodku). Przekr´ciç Êrub´ w kierunku zgodnym z ru-

chem wskazówek zegara do po∏o˝enia, w którym p∏o-

mieƒ b´dzie ma∏y i stabilny.

3. Sprawdziç czy p∏omieƒ nie gaÊnie podczas szybkiego

kr´cenia zaworem

4. W przypadku niew∏aÊciwego dzia∏ania kuchenek wypo-

sa˝onych w urzàdzenie zabezpieczajàce (termoelement)

przy ustawieniu najmniejszego p∏omienia, nale˝y zwi´kszyç

wielkoÊç p∏omienia za pomocà Êruby.

W przypadku zasilania gazem p∏ynnym, Êruba regulacyj-

na powinna byç ca∏kowicie wkr´cona do samego koƒca.

Po zakoƒczonej regulacji, nale˝y zmieniç nalepk´ z opi-

sem rodzaju gazu, do jakiego kuchnia jest przystosowana.

JeÊli ciÊnienie gazu w instalacji ró˝ni si´ od wartoÊci, po-

danych w niniejszej instrukcji, nale˝y zastosowaç regulator

ciÊnienia.

Drying:

DANE TECHNICZNE

Mogà byç dostosowane do ró˝nych

rodzajów gazu, zgodnie z informacjà

przedstawionà na tabliczce znamionowej,

znajdujàcej si´ na:

– wewn´trznej stronie drzwiczek schowka;

– wewn´trznej stronie lewego boku kuchni

widoczna po wysuni´ciu szuflady.

Zobacz tabliczk´ znamionowà

Etykieta energetyczna jest zgodna

z Dyrektywà UE 2002/40/CE (norma EN

50304).

Energoch∏onnoÊç podana w oparciu

o nastawy piekarnika:

– pieczenie statyczne:

wybrana funkcja Tryb konwencjonalny

Deklarowana klasa energoch∏onnoÊci

podana dla trybu dynamicznego

– pieczenie dynamiczne:

wybrana funkcja „Pieczenie ciast”

szerokoÊç 44 cm

wysokoÊç 34 cm

g∏´bokoÊç 38 cm

szerokoÊç 42 cm

wysokoÊç 23 cm

g∏´bokoÊç 44 cm

54 litry

Ø180

Palniki

Napi´cie

i cz´stotliwoÊç

zasilania

Etykieta

energetyczna

Wymiary

piekarnika

PojemnoÊç

piekarnika

Szuflada/

schowek kuchni

Dyrektywy unijne: 2006/95/EC z

dnia 12/12/06 (niskie napiêcie) z

póniejszymi zmianami

z dnia 15/12/04 (zgodnoæ

elektromagnetyczna) z

póniejszymi zmianami -

93/68/EEC z dnia 22/07/93 z

póniejszymi zmianami,

2009/142/EC z dnia 30/11/09 (gaz)

z póniejszymi zmianami, -

93/68/EEC z dnia 22/07/93 z

póniejszymi zmianami, -

2002/96/EC.

* przy gazie suchym 15°C 1013 mbar

G20 (GZ 50) p.c.i. 37,78 Mj/m

GZ350 (GZ35) p.c.i. 27,20 Mj/m

G30 (GPB) p.c.i. 49,47 MJ/kg

Palnik

Szybki (du˝y – R)

Âredniej pr´dkoÊci (Êredni – S)

Pomocniczy (ma∏y) (A)

CiÊnienie gazu

Ârednica

(mm)

Moc

termiczna

(p.c.i*)

Min.

Moc

termiczna

(p.c.i*)

Nominalna

Moc

termiczna

(p.c.i*)

Nominalna

Dysza

1/100

(mm)

Przep∏yw*

l/h

G20 (GZ50) G2.350 (GZ350)

Dysza

1/100

(mm)

Przep∏yw*

l/h

Dysza

1/100

(mm)

Przep∏yw*

g/h

1000,70128 2861583973,4087247

750,401041811432512,2070160

0,40

76951061321,305295

Minimalne

Nominalne (mbar)

Maksymalne

3,00

1,90

1,00

Gaz naturalny

G30 (GPB)

Gaz p∏ynny

Parametry dysz i palników

DANE TECHNICZNE

1275/2008 (Stand-by/ Off mode)

UWAGA! Szklana pokrywa może

popękać jeżeli zostanie nagrzana.

Należy wyłączyć wszystkie palniki

przed zamknięciem pokrywy. *Dotyczy

tylko modeli ze szklana pokrywa.

KN3G65SA/U

KN3G66SA/U

KN3G62SA/U

KN3G6SA/U

KN3G60SA/U

KN3G610SA/U

KN3G620SA/U

KN3G650SA/U

KN3G660SA/U

KN3M6SA/U

Opis kuchni

Ogólny widok

Palniki gazowe

P∏yta podpalnikowa

poziom 5

poziom 4

poziom 3

poziom 2

poziom 1

PROWADNICE

do wsuwania rusztu i tacy

Regulowane

nó˝ki

P∏yta podpalnikowa

Elektryczna p∏yta

grzewcza

poziom 5

poziom 4

poziom 3

poziom 2

poziom 1

PROWADNICE

do wsuwania rusztu i tacy

Regulowane

nó˝ki

Ruszt

Panel sterujàcy

KRATKA piekarnika

TACA na kapiàcy t∏uszcz

lub do pieczenia

Regulowane nó˝ki

Palniki gazowe

Ruszt

Panel sterujàcy

KRATKA piekarnika

TACA na kapiàcy t∏uszcz

lub do pieczenia

Regulowane nó˝ki

* Dost´pne w niektórych modelach.

Strona jest ładowana ...

Whirlpool KN3G620SA(W)/U instrukcja

Marka: Whirlpool

Model: KN3G620SA(W)/U

Kategoria: Mikrofale

Typ: instrukcja

ściągnij PDF

raport

w innych językach

eesti: Whirlpool KN3G620SA(W)/U Kasutusjuhend
English: Whirlpool KN3G620SA(W)/U User guide

Powiązane dokumenty

Inne dokumenty

Master BG 100-200 Instrukcja obsługi