TP-LINK TL-SG1005LP 16 Port Gigabit Desktop PoE Switch Instrukcja instalacji

TP-LINK
Marka
TP-LINK
Model
TL-SG1005LP 16 Port Gigabit Desktop PoE Switch
Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji
Connection
© 2023 TP-Link 7106510100 REV4.1.1
Installation Guide
5/16-Port Gigabit Desktop PoE Switch
LED Explanation
Note: For simplicity, we will take TL-SG1005P for example throughout this Guide.
Note:
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. TL-SG1005LP can supply up to 30 W for each PoE port and 40 W for all PoE ports.
3. TL-SG1005P can supply up to 30 W for each PoE port and 65 W for all PoE ports.
4. TL-SG116P can supply up to 30 W for each PoE port and 120 W for all PoE ports.
DC Power Adapter
AC Power Cord
IP Camera AP IP Phone
Router
LAN Port WAN Port
Internet
Ethernet Ports (1-5)
PoE Ports (1-4)
Power
On: Power on
O: Power o
Power
PoE MAX
PoE Max
TL-SG1005LP
On: 33 W ≤ Total power supply < 40 W
Flashing: Total power supply ≥ 40 W
O: Total power supply < 33 W
TL-SG1005P
On: 58 W ≤ Total power supply < 65 W
Flashing: Total power supply ≥ 65 W
O: Total power supply < 58W
Link/Act and PoE Status
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
On (Green): Connected to a 1000 Mbps
device
On (Yellow): Connected to a 10/100
Mbps device
Flashing: Transmitting/receiving data
O: No device is connected to the
corresponding port.
TL-SG116P
On: Total power supply ≥ 113 W
Flashing: Total power supply ≥ 113 W and lasts
for more than 2 minutes
O: Total power supply < 113W
PoE Devices
Switches Explanation
Priority (for TL-SG116P)
O: All the ports transmit data with the same priority.
On: The corresponding ports transmit data with a higher priority than other ports. When congestion
occurs, packets which are transmitted by the ports with a higher priority occupy the whole bandwidth.
Isolation (for TL-SG116P)
O: Ports can transmit data with each other.
On: The corresponding ports cannot transmit data with other downlink ports. They can transmit data
only with the uplink ports (ports 15-16 of TL-SG116P).
Extend (for TL-SG1005P/TL-SG116P)
O: The corresponding ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to 250 m away.
Recovery (for TL-SG1005P/TL-SG116P)
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch
nds that the PD works abnormally, the switch will reboot it.
Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power LED is
not lit, please try the following:
A1:
Make sure the AC power cord is connected to the switch with power source properly.
A2:
Make sure the voltage of the power supply meets the requirements of the input voltage
of the switch.
A3: Make sure the power source is on.
Q1. Why is the Power LED not lit?
It is recommended that you check the following items:
A1: Make sure that the cable connectors are rmly plugged into the switch and the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it
should be less than 250 meters (820 feet).
Q2. Why is the Link/Act LED not lit while a device is connected to
the corresponding port?
Q3. Why are PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the maximum, the
PoE port with a smaller port number has higher priority. The system will cut o power to the
ports with larger port numbers to ensure supplying to other ports.
Take TL-SG1005P as an example. If port 1, 2 and 4 are consuming 15.4 W respectively, and
an additional PoE device with 19 W is connected to port 3, the system will cut o the power
of port 4 to compensate for the overload.
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at
https://www.tp-link.com/en/support/ce/
EU declaration of conformity
UK declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and
Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at
https://www.tp-link.com/support/ukca
IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x,
IEEE802.3af, IEEE802.3at, IEEE802.1p
CSMA/CD
For TL-SG1005LP/TL-SG1005P:
5 10/100/1000 Mbps RJ45 Ports
Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-Port 4
For TL-SG116P:
16 10/100/1000 Mbps RJ45 Ports
Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-Port 16
Total Power Supply:
40 W (TL-SG1005LP)/65 W (TL-SG1005P)/120 W (TL-SG116P)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
1000BASE-T: UTP category 5e cable or above (maximum 100
m); EIA/TIA-568 100Ω STP (maximum 100 m)
10 Gbps (TL-SG1005LP/TL-SG1005P)/32 Gbps (TL-SG116P)
2 K (TL-SG1005LP/TL-SG1005P)/8 K (TL-SG116P)
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output:
53.5 VDC /0.81 A (TL-SG1005LP)
53.5 VDC /1.31 A (TL-SG1005P)
53.5 VDC /2.43 A (TL-SG116P)
Ye s
39 mm (TL-SG1005LP/TL-SG1005P)/200 mm (TL-SG116P)
Standard
General Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)
-40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
Specications
Wall Mountable
Distance Between
Mounting Holes
Network Media (Cable)
Switching Capacity
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
To ask questions, find answers, and communicate with TP-Link
users or engineers, please visit https://community.tp-link.com
to join TP-Link Community.
Power Supply
Interface
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please
contact us.
Place the device with its bottom surface downward.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Protocol
MAC Address Table
Transfer Method
MAC Address Learning
The plug on the power supply cord is used as the disconnect device, the
socket-outlet shall be easily accessible.
A1: Before upgrading a connected PoE powered device (PD), disable PoE Auto Recovery to
avoid the PD’s damage.
A2: When a PD does not send data packets to the switch for a long period in certain
scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD
repeatedly rebooting.
Q4. What should I notice before using the PoE Auto Recovery
feature?
FCC compliance information statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1)This device may not cause harmful interference.
2)This device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
We, TP-Link USA Corporation, has determined that the equipment shown as
above has been shown to comply with the applicable technical standards, FCC
part 15. There is no unauthorized change is made in the equipment and the
equipment is properly maintained and operated.
Issue Date: 2023/03/09
Product Name: 5/16-Port Gigabit Desktop PoE Switch
Model Number: TL-SG1005LP/TL-SG1005P/TL-SG116P
Component Name Model
T535081-2-DT (For TL-SG1005LP)
T535131-2-DT (For TL-SG1005P)
T535243-2-DT (For TL-SG116P)
I.T.E. Power Supply
Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: [email protected]
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на
відповідність вимогам нормативних документів та вимогам, що передбачені
чинними законодавчими актами України.
この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害
を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求
されることがあります。 VCCI-A
CAN ICES-3 (A)/NMB-3(A)
Industry Canada Statement
This is a class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to take
adequate measures.
CE Mark Warning
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。
警告：為避免電磁干擾，本產品不應安裝或使用於住宅環境。
Explanation of the symbols on the product label
Note: The product label can be found at the bottom of the product.
限用物質含有情況標示聲明書
限用物質及其化學符號
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
Cr+6
多溴聯苯
PBB
多溴二苯醚
PBDE
單元
PCB
外殼
電源供應器
備考1. “ “系指該項限用物質之百分比含量未超出百分比含量基準值。
備考2. “ “系指該項限用物質為排除項目。
Direct current
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be
handled pursuant to European directive 2012/19/EU in order to be
recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when he buys a new electrical or electronic
equipment.
For indoor use only
Polarity of d.c. power connector
Energy eciency Marking (Level VI)
Caution
Operator's manual
  • Page 1 1
  • Page 2 2
  • Page 3 3

TP-LINK TL-SG1005LP 16 Port Gigabit Desktop PoE Switch Instrukcja instalacji

TP-LINK
Marka
TP-LINK
Model
TL-SG1005LP 16 Port Gigabit Desktop PoE Switch
Kategoria
Przełączniki sieciowe
Typ
Instrukcja instalacji
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty