Yamaha RX-V2200 Instrukcja obsługi

OWNER’S MANUAL

RX-V2200

U

AV Receiver

IMPORTANT

Please record the serial number of this unit in the

space below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia

V795410

0100V2200(U)-cv1/4 01.8.1, 10:24 AM1

I CAUTION

SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

6 Attachments – Do not use attachments not recommended

by the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

product and cart combination to overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or

rack unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into

the product,

c) If the product has been exposed to rain or water,

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

0101V2200_Cau_EN(U) 01.8.1, 9:43 AM2

SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS

CAUTION II

1. IMPORTANT NOTICE : DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

FCC INFORMATION (for US customers only)

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in

performance - this indicates a need for service.

20 Replacement Parts – When replacement parts are

required, be sure the service technician has used

replacement parts specified by the manufacturer or have

the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric

shock, or other hazards.

21 Safety Check – Upon completion of any service or

repairs to this product, ask the service technician to

perform safety checks to determine that the product is in

proper operating condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the

antenna or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA

70, provides information with regard to proper grounding of

the mast and supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection

to grounding electrodes, and requirements for the

grounding electrode.

0101V2200_Cau_EN(U) 01.8.1, 9:43 AM3

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 30 cm on the top, 20 cm on the

right and left, and 10 cm at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a

room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal

injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may

cause fire, damage to this unit, and/or personal

injury.

– Containers with liquid in them, as they may

cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper,

tablecloth, curtain, etc. in order not to obstruct

heat radiation. If the temperature inside this unit

rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

III CAUTION

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than

specified is dangerous and may cause fire,

damage to this unit, and/or personal injury.

YAMAHA will not be held responsible for any

damage resulting from use of this unit with a

voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an

electrical storm.

14 Take care of this unit so that no foreign objects

and/or liquid drops inside this unit.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long

periods of time (i.e. vacation), disconnect the AC

power plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding

that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

19 VOLTAGE SELECTOR (China and General models

only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage

BEFORE plugging into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your equipment

by playing it at a safe level. One that lets the sound come through

loud and clear without annoying blaring or distortion – and, most

importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

0101V2200_Cau_EN(U) 01.8.1, 10:18 AM4

English

INTRODUCTION

PREPARATION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

1

CONTENTS

INTRODUCTION

CONTENTS ....................................................... 1

FEATURES ........................................................ 2

GETTING STARTED ....................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS .................... 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Using the Remote Control ........................................ 7

Front Panel Display .................................................. 8

Rear Panel ................................................................ 9

PREPARATION

SPEAKER SETUP .......................................... 10

Speakers to Be Used ............................................... 10

Speaker Placement ................................................. 10

Connecting the Speakers ........................................ 11

CONNECTIONS ............................................. 14

Before Connecting Components ............................ 14

Connecting Video Components .............................. 14

Connecting Audio Components ............................. 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ............................ 18

Connecting the Power Supply Cords ...................... 19

Turning on the Power ............................................. 20

ON-SCREEN DISPLAY (OSD) ..................... 21

OSD Modes ............................................................ 21

Selecting the OSD Mode ........................................ 21

SPEAKER MODE SETTINGS ..................... 22

Summary of SPEAKER SET Items 1A through 1F ...

22

ADJUSTING THE SPEAKER OUTPUT

LEVELS ....................................................... 23

Before You Begin ................................................... 23

Using the Test Tone (TEST DOLBY SUR.) .......... 23

BASIC OPERATION

BASIC PLAYBACK ........................................ 25

Input Modes and Indications .................................. 27

Selecting a Sound Field Program ........................... 28

Selecting PRO LOGIC or Neo: 6 ....................... 29

DIGITAL SOUND FIELD PROCESSING

(DSP) ............................................................ 31

Understanding Sound Fields .................................. 31

Hi-Fi DSP Programs............................................... 31

CINEMA-DSP ................................................. 32

Sound Design of CINEMA-DSP ............................ 32

CINEMA-DSP Programs ....................................... 34

TUNING ........................................................... 36

Connecting the Antennas ........................................ 36

Automatic and Manual Tuning ............................... 37

Presetting Stations .................................................. 38

Tuning in to a Preset Station .................................. 40

Exchanging Preset Stations .................................... 40

BASIC RECORDING ..................................... 41

ADVANCED OPERATION

REMOTE CONTROL FEATURES .............. 42

Control Area ........................................................... 42

Setting the Manufacturer Code .............................. 43

Programming a New Remote Control Function

(Learn Feature) ................................................... 44

Using the Macro Feature ........................................ 45

Changing the Source Name in the Display Window

............................................................................ 47

Clearing Learned Functions, Macros, Renamed

Source Names, and Setup Manufacturer Codes ...

47

Clearing a Learned Function or Macro .................. 48

Each Component Control Area .............................. 50

SET MENU ...................................................... 55

Adjusting the Items on the SET MENU................. 55

1 SPEAKER SET (speaker mode settings) ........... 56

2 LOW FRQ TEST ............................................... 59

3 L/R BALANCE (balance of the left and right main

speakers)............................................................. 60

4 HP TONE CTRL (headphone tone control) ....... 60

5 CENTER GEQ (center graphic equalizer) ......... 60

6 INPUT RENAME .............................................. 61

7 I/O ASSIGNMENT ............................................ 61

8 INPUT MODE (initial input mode) ................... 62

9 PARAM. INI (parameter initialization) ............. 63

10 LFE LEVEL ..................................................... 63

11 DYNAMIC RANGE ......................................... 64

12 SP DELAY TIME ............................................. 64

13 DISPLAY SET .................................................. 65

14 MEMORY GUARD ......................................... 65

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS .................................................. 66

SLEEP TIMER ................................................ 67

Setting the Sleep Timer .......................................... 67

Canceling the Sleep Timer ..................................... 67

ZONE 2 ............................................................ 68

Zone 2 Connections ................................................ 68

Remote Control in Zone 2 ...................................... 69

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM PARAMETER

EDITING ..................................................... 70

What is a sound field? ............................................ 70

Sound Field Program Parameters ........................... 70

Changing Parameter Settings ................................. 71

Resetting a Parameter to the Factory-set Value ...... 71

DIGITAL SOUND FIELD PARAMETER

DESCRIPTIONS ......................................... 72

TROUBLESHOOTING .................................. 76

GLOSSARY ..................................................... 81

SPECIFICATIONS ......................................... 83

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM1

2

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS”, “DTS-ES Extended Surround” and “Neo: 6” are

trademarks of Digital Theater System, Inc.

FEATURES

Built-in 6-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz, 8Ω)

Main: 100 W + 100 W

Center: 100 W

Rear: 100 W + 100 W

Rear center: 100 W

Multi-Mode Digital Sound Field

Processing

◆ Dolby Pro Logic/Dolby Pro Logic Decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder

◆ DTS/DTS ES Matrix 6.1, Discrete 6.1, DTS

Neo: 6 Decoder

◆ CINEMA DSP: Combination of YAMAHA DSP

Technology and Dolby Pro Logic, Dolby Digital

or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with 14 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal Jacks

◆ Sleep Timer

◆ Remote Control with Preset Manufacturer Codes

and “Learning” Capability

◆ PROCESSOR DIRECT for no alteration of the

original signal

◆ Custom Installation Facility

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this

manual.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM2

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

3

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

A

B

CD

DVD

VCR2/DVR

VCR 1

TITLE

MENU

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

TV

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SEARCH

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

1

5

9

6

10

0

10

100

11 12

78

234

+

Installing Batteries in the Remote

Control

1 Open the battery compartment cover.

2 Insert three supplied batteries (R6) in the

correct direction by aligning the + and –

marks on the batteries with the polarity

markings (+ and –) on the inside of the

battery compartment.

3 After new batteries are correctly inserted,

press the RESET button in the battery

compartment using a ball point pen or

similar object. (This does not clear the

contents of the memory.)

4 Replace the cover as pressing until it snaps

into place.

■ Notes on batteries

• Change all of the batteries if you notice the condition

like; the operating range of the remote control

decreases, the indicator does not flash or its light

becomes dim.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean

the battery compartment thoroughly before installing

new batteries.

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

Connection GuideAM loop antenna

Indoor FM antenna

(Australia model)

Indoor FM antenna

(U.S.A., Canada, China and

General models)

Batteries (3) (R6)

Remote control

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Power Cord

(U.S.A., and Canada models

only)

RESET button

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

SPEAKERS

TUNER

75Ω UNBAL.

AM

ANT

GND

FM

ANT

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

/ C

R

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

REAR

P

B

/ C

B

Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

CD

PHONO

IN

OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

/LD

CD

CBL

/SAT

(SURROUND)

COAXIAL

+

–

+

–

A

B

SUB

WOOFER

LR

AUDIO OUT S VIDEO

OUT

VIDEO

OUT

OPTICAL

IN

COMPONENT

VIDEO OUT

AUDIO

OUT

S VIDEO IN VIDEO IN

S VIDEO

OUT

VIDEO

OUT

OPTICAL

IN

O

COMPONENT

VIDEO IN

COMPONENT

VIDEO OUT

RIGHT LEFT

RIGHT

LEFT

L R

S

V

S

V

DVD Player Main Speaker

TV Subwoofer Center Speaker Rear Center

Speaker

Rear Speaker

CONNECTION

GUIDE

L

R

V

S

O

Analog audio signal

Optical digital signal

S video signal

Video signal

Signal flow

V795390

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM3

4

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUX

SILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

/

ON

NATURAL SOUND AV RECEIVER

6CH INPUT

–+

TREBLE

–+

PRO LOGIC

AB

DIGITAL

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

CD

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

123 4567

8

90 qw

e

r

t

y

u

d

s

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

FM/AM

o

p

ai

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit (see page 8).

4 INPUT MODE

Sets the priority for the types of input signals (AUTO,

DTS, ANALOG) to receive when one component is

connected to two or more input jacks of this unit (see

page 27). Priority cannot be set when 6CH INPUT is

selected as the input source.

5 INPUT l / h

Selects the input source you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH INPUT takes

priority over the source selected with INPUT l / h (or

the input selector buttons on the remote control).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel at each time its

corresponding button is pressed.

9 BASS EXTENSION

Turns on or off the BASS EXTENSION function at each

time the button is pressed, this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

However, this boost may not be noticeable if “1B MAIN

SP” on the SET MENU is set to SMALL and “1E LFE/

BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT

Turns on or off the PROCESSOR DIRECT function at

each time the button is pressed. When this is on, BASS,

TREBLE, and BASS EXTENSION are bypassed,

eliminating any alteration of the original signal.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM4

5

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

D

I

G

I

T

A

L

To open, press gently on the lower part of the panel.

q REC OUT/ZONE 2

Selects the source you want to direct to the audio/video

recorder and ZONE 2 outputs independent of the source

you are listening to in the main room. When set to the

SOURCE/REMOTE position, the input source is directed

to all outputs.

w STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are mixed down to the main left and

right speakers.

e A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

r PROGRAM l / h

Selects the DSP program (see page 28).

t PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

y PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the OUTPUT jacks or to the speakers.

u VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source.

i PRESET/TUNING EDIT

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset

station number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

o FM/AM

Switches the reception band between FM and AM.

p MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

a TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

s BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

d TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center and rear speakers may not match that of the left and

right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front

panel door, close the door.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM5

6

CONTROLS AND FUNCTIONS

TRANSMIT

RE-NAME

STANDBY

6CH INPUT

SOUND

SYSTEM

CLEAR LEARN MACRO

OFF ON

MACRO

PHONO

A

B

CD

DVD

VCR2/DVR

VCR 1

TITLE

MENU

CHAPTER

PAUSESTOPPOWER

REC

HALL 1

6.1/ES

DSP

10KEY

ROCK

CONCERT

MOVIE

THEATER 1

MOVIE

THEATER 2

MUTE

VOLUME

STEREO

TV INPUT

TV VOL

CH

PRESET

DISC

PARAMETER

SET MENU

EFFECT

LEVEL

ON SCREEN

TESTSLEEP

TV MUTE

TV

SPORTS

MONO

MOVIE

ENTER-

TAINMENT

HALL 2

CHURCH

JAZZ CLUB

SELECT

/DTS

SUR.

CHP/INDEX

A/B/C/D/E

SELECT

DISPLAY

SEARCH

SOURCE

PLAY

– +

ENTER

D-TV/LD

CBL/SAT

CD-R

MD/TAPE

TUNER

V-AU X

POWER

1

5

9

6

10

0

10

100

11 12

78

234

+

1

2

3

4

5

6

7

9

q

w

e

r

8

0

t

y

u

i

o

s

f

d

a

h

j

g

p

Remote Control

This section describes the controls and their functions of

the remote control. See “REMOTE CONTROL

FEATURES” on pages 42 to 54 for operating other

components with this remote control.

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 RE-NAME

Used for changing the input source name in the display

window (see page 47).

3 TRANSMIT indicator

Flashes while the remote control is sending signals.

4 STANDBY

Sets this unit in the standby mode.

5 SYSTEM POWER

Turns on the power of this unit.

6 Display window

Shows the selected source component that you are

controlling.

7 SOURCE SELECT k/n

Selects the another component to control independently

from the input that has been selected by pressing an input

selector button.

8 10KEY/DSP

Selects the numeric button (10KEY) mode or DSP mode.

9 Operation buttons

Provides functions such as play, stop, skip, etc. for

operating your other components selected by the input

selector buttons.

0 6.1/ES

Turns on or off the Dolby Digital Matrix 6.1 or DST ES

decoder with 10 KEY/DSP set to the DSP position.

q LEVEL

Selects the effect speaker channel to be adjusted and sets

the level.

w ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

e SLEEP

Sets the sleep timer.

r TEST

Outputs the test tone to adjust the speaker levels.

t CLEAR

Used for clearing functions acquired when using the learn

and rename features, and set manufacturer codes (see

page 47).

y LEARN

Used for setting up the manufacturer code or for

programming the functions of other remote controls (see

pages 43 and 44).

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM6

7

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

BASS

VOLUMEINPUT

INPUT M0DE

VIDEO AUXSILENT

PROGRAM

STEREO

SPEAKERS

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET

/

TUNING

PHONES

EFFECT

A/B/C/D/E

S VIDEO

MEMORY

FM/AM

EDIT

PRESET

/TUNING

MAN'L/AUTO FM AUTO/MAN'L MONO

TUNING

MODE

VIDEO AUDIO OPTICALLR

STANDBY

/

ON

NATURAL SOUND AV RECEIVER

6CH INPUT

– +

TREBLE

– +

PRO LOGIC

AB

DIGITAL

REC OUT/ZONE 2

V-AUX

VCR2

/DVR

VCR1

PHONO

CD

TUNER

MD/TAPE

DVD

SOURCE

/REMOTE

D-TV/LD

CBL/SAT

CD-R

30°30°

Approximately 6 m (20 feet)

u MACRO

Used to program a series of operations for control by a

single button (see page 46).

i MACRO ON/OFF

Turns the macro function on and off.

o Å and ı

Switch the control area for the extra components that are

not connected to this unit without changing the input.

p Input selector buttons

Select the input source and change the control area.

a 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

s DSP program/Numeric buttons

Select DSP programs or numbers according to the

position of 10KEY/DSP.

d MUTE

Mutes the sound. The MUTE indicator turns on when the

MUTE function is on. Press again to restore the audio

output to the previous volume level.

f VOLUME +/–

Increases or decreases the volume level.

g STEREO/EFFECT

Switches the normal stereo or DSP effect reproduction.

When STEREO is selected, 2-channel input signals are

directed to the main left and right speakers without effect

sounds. All Dolby Digital and DTS audio signals except

for the LFE channel are also directed to the main left and

right speakers.

h PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

j Cursor buttons k/n/–/+

Select and adjust DSP program parameters and SET

MENU items according to the position of PARAMETER/

SET MENU.

Using the Remote Control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM7

8

CONTROLS AND FUNCTIONS

RL

LCR

RC RR

LFE

VIRTUAL

DTS

Neo

MOVIE THEATER

ENTERTAINMENT12

:6

DOLBY DIGITAL

PRO

LOGIC

VCR DVD TUNER CD

PHONO

CD RV AUX

DSP

DISCRETE

PCM

1

SILENT

SP

DIGITAL

VCR2/DVR

CBL

/

SAT

MD

/

TAPE

TV

/

LD

STEREO

TUNED

MEMORY

P. DIRECT

BASS

MUTE VOLUME

SLEEP

AUTO

D

6.1

/

ES

PRO LOGIC

/

AB

78 q wertyui

123456

90

1 Processor indicators

When any function of DSP, DTS, DISCRETE,

VIRTUAL, g, 6.1/ES, and

PRO LOGIC

/

is

activated, its indicator lights up.

2 Input source indicator

Shows the current input source with underneath.

3 AUTO indicator

Shows that this unit is in the automatic tuning mode.

4 SLEEP indicator

Lights up while the sleep timer is on.

5 MUTE indicator

Lights up while the MUTE function is on.

6 VOLUME level indicator

Indicates the volume level.

7 v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

8 Headphones indicator

Lights up when headphones are connected.

9 SP A B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

0 SILENT indicator

Lights up when headphones are connected with the sound

effect (see “SILENT CINEMA DSP” on page 30).

q DSP program indicators

The name of the selected DSP program lights up when

the ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or V/DTS SURROUND DSP program is

selected.

w Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

e STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

r TUNED indicator

Lights up when this unit tunes in to a station.

t MEMORY indicator

Flashes to show a station can be stored.

y BASS indicator

Lights up while BASS EXTENSION is on.

u P. DIRECT

Lights up while PROCESSOR DIRECT is on.

i Input channel indicator

Indicates the channel components of input signals being

received.

Front Panel Display

0102V2200_1-9_EN(U) 01.8.4, 3:08 PM8

9

English

INTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL OUT SPEAKERS

TUNER

REMOTE

IN

75Ω UNBAL.

OUT

AM

ANT

GND

FM

ANT

+12V

10mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

PR/ CR

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

CENTER

REAR

PB/ CB Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

/LD

CD

CBL

/SAT

(SURROUND)

COAXIAL

+

–

+

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

:

A

B

AC IN

1

8

9 0 w e rq

2

3

4

5

6

7

*1

(U.S.A. model)

1 DIGITAL OUTPUT jacks

2 Audio component jacks

See pages 16 and 17 for connection information.

3 Video component jacks

See pages 14 and 15 for connection information.

4 REMOTE IN/OUT jacks

See page 68 details.

5 OUTPUT jacks

See page 18 for connection information.

6 AC INLET (U.S.A. and Canada models only)

Use this inlet to plug in the supplied power cord.

7 AC OUTLET(S)

Use these outlets to supply power to your other A/V

components (see page 19).

8 DIGITAL INPUT jacks

9 6CH INPUT jacks

See page 18 for connection information.

0 ZONE 2 OUT jacks

See page 68 for details.

q Antenna input terminals

See page 36 for connection information.

w CONTROL OUT

This is a control expansion terminal for commercial use.

e Speaker terminals

See pages 11 and 12 for connection information.

r IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance (see page 13). Set this unit in the

standby mode before you change the setting of this

switch.

< China and General models only >

FREQUENCY STEP switch

See page 36.

VOLTAGE SELECTOR

See page 19.

*1 As this terminal is used for an examination in the factory, do not

connect any equipment to this terminal.

Rear Panel

0102V2200_1-9_EN(U) 01.8.1, 9:43 AM9

10

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound-

field quality with a 6-speaker system, using left and right

main speakers, left and right rear speakers, and a center

and rear center speakers. If you use different brands of

speakers (with different tonal qualities) in your system,

the tone of a moving human voice and other types of

sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). If

for some reason it is not practical to use a center speaker,

you can do without it. Best results, however, are obtained

with the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers. For

precise sound localization, however, it is ideal to use the

models of equivalent performance with the main

speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

PREPARATION

Speaker Placement

Refer to the following diagram when you place the

speakers.

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will

be heard from the left and right main speakers. In this case,

“1A CENTER SP” on the SET MENU is set to NONE (see

page 56 for details).

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (6 feet) above the

floor.

■ Rear center speaker

Place the rear center speaker in the center between the left

and right rear speakers at the same height from the floor

as the rear speakers.

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

CAUTION

Use magnetically shielded speakers. If this type of

speakers still creates the interference with a monitor,

place the speakers away from the monitor.

Main

speaker (L)

1.8 m (6 feet)

Rear speaker (L)

Rear center

speaker

Rear speaker (R)

Subwoofer

Main speaker (R)Center speaker

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM10

11

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

12

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage this unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approximately 10 mm (3/8”) of

insulation from each of the speaker cables.

2 Twist the exposed wires of the cable

together to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

y

(U.S.A., Canada, Australia, China and General models only)

• Banana plug connections are also possible. First, tighten the

knob and then insert the banana plug connector into the end of

the corresponding terminal.

10 mm (3/8”)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

■ REAR CENTER SPEAKER terminals

A rear center speaker can be connected to these terminals.

Red: positive (+)

Black: negative (–)

Banana plug

3

1

2

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM11

12

SPEAKER SETUP

AC OUTLETS

CENTER

SUB

WOOFER

S VIDEO

MONITOR OUT

VIDEO

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO AUDIO VIDEO

CONTROL OUT SPEAKERS

TUNER

REMOTE

IN

75Ω UNBAL.

OUT

AM

ANT

GND

FM

ANT

+12V

10mA

MAX.

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

/ C

R

DVD

MONITOR

OUT

D-TV / LD

MAIN

REAR

CENTER

OUTPUT

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SUB

WOOFER

CENTER

REAR

CENTER

REAR

P

B

/ C

B

Y

R

L

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

DVD

D-TV

CD

PHONO

IN

OUT

ZONE 2 OUT

VCR 2

/DVR

VCR 1

IN

MAIN

SURROUND

/LD

CD

CBL

/SAT

(SURROUND)

COAXIAL

+

–

+

–

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR

REAR CENTER

:

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

:

A

B

AC IN

1

4567

23

Subwoofer

system

Rear Center

speaker

Main B speaker

Center

speaker

(U.S.A. model)

Right

Rear speaker

■ SUBWOOFER jack

When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,

connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or

rear channels are directed to this jack if they are assigned to this jack. (The cut-off frequency of this jack is 90 Hz.) The

LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are

assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on the subwoofer. It is also possible to adjust the volume level by using the

remote control of this unit (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 66).

• Depending on the settings of “1 SPEAKER SET” and “10 LFE LEVEL” on the SET MENU, some signals may not be output from

the SUBWOOFER jack.

Right Left

Main A speaker

Right Left

Left

1

2

3

4

5

7

6

The diagram above shows the speaker layout in the

listening room.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM12

13

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

AC OUTLETS

AC IN

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

REAR CENTER

:

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

:

IMPEDANCE SELECTOR

REAR

8ΩMIN. /SPEAKER

16ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

MAIN A OR B:

A+B:

CENTER

REAR

REAR CENTER

:

IMPEDANCE SELECTOR

SET BEFORE POWER ON

MAIN A OR B:

A+B:

CENTER

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

6ΩMIN. /SPEAKER

REAR

REAR CENTER

:

Switch

position

Left

Right

Speaker

Main

Center

Rear

Center

Rear

Main

Center

Rear

Center

Rear

Impedance level

If you use one set of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 8 Ω or higher.

The impedance must be 6 Ω or higher.

The impedance of each speaker must be 6 Ω or higher.

If you use one set of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two sets of main speakers, the impedance of

each speaker must be 16 Ω or higher.

[Canada model only]

The impedance of each speaker must be 8 Ω or higher.

The impedance must be 8 Ω or higher.

The impedance of each speaker must be 8 Ω or higher.

IMPEDANCE

SELECTOR

switch

(U.S.A. model)

■ IMPEDANCE SELECTOR switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise this unit

may be damaged.

If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the

standby mode.

Select the left and right position according to the impedance of the speakers in your system. Be sure to move this switch

only when this unit is in the standby mode.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM13

14

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different jack names. Refer to the operation instructions

for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling

system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video

signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.

The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO

jacks are separated into luminance (Y) and color difference (P

B

/C

B

, P

R

/C

R

) video signals. The jacks are also separated

into three for each signal. The description of the component video jacks may be different depending on the component

(e.g. Y, C

B

, C

R

/Y, P

B

, P

R

/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the

S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks

on your video component to the COMPONENT VIDEO jacks.

y

• Each type of video jack works independently. Signals input through the composite

video, S-video and component jacks are output through the corresponding composite

video, S-video, and component jacks, respectively.

• You can designate the input for the COMPONENT VIDEO A and B jacks according

to your component by using “7 I/O ASSIGNMENT” on the SET MENU (see pages

61 and 62 for details).

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when

connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being

connected.

■ VIDEO AUX jacks (on the front panel)

These jacks are used to connect any video input source

such as a game console and a camcorder to this unit.

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

O

V

L

R

S

Game console or camcorder

VIDEO

COMPONENT VIDEO

S VIDEO VIDEO

P

R

/ C

R

P

B

/ C

B

Y

VIDEO jack

(composite)

COMPONENT

VIDEO jacks

S VIDEO

jack

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM14

15

English

INTRODUCTION

PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

CENTER

SUB

WOOFER

DIGITAL OUTPUT

DIGITAL INPUT

6CH INPUT

GND

AUDIO

TUNER

75Ω UNBAL.

AM

ANT

GND

FM

ANT

MAIN

SUB

WOOFER

R

L

R

L

OPTICAL

MD

/

TAPE

IN

(

PLAY

)

IN

(

PLAY

)

OUT

(

REC

)

OUT

(

REC

)

CD-R

MD/TAPE

CD-R

CD

PHONO

MAIN

SURROUND

CD

+

–

A

B

COAXIAL

CBL

/SAT

AUDIO VIDEO

COMPONENT VIDEO

S VIDEO

DVD

D-TV

/LD

CBL

/SAT

VIDEO

P

R

/ C

R

DVD

MONITOR

OUT

D-TV / LD

P

B

/ C

B

Y

R

L

IN

OUT

VCR 2

/DVR

VCR 1

IN

S VIDEO

MONITOR OUT

VIDEO

DVD

/LD

D-TV

CONTROL OUT

REMOTE

IN

OUT

+12V

10mA

MAX.

ZONE 2 OUT

L

R

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO INPUT

AUDIO OUTPUT

COAXIAL

OUTPUT

OPTICAL

OUTPUT

RF

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

RF

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

O

COMPONENT

INPUT

COMPONENT

OUTPUT

COMPONENT

OUTPUT

L

R

C

*1

L

R

L

R

V

S

S VIDEO

INPUT

S

V

S

V

S

L

R

L

S

R

V

C

O

(U.S.A. model)

LD player

RF

demodulator

*1 If your LD player has an RF

OUTPUT jack, first connect it to

the RF INPUT on an RF

demodulator and then connect

the RF OUTPUT on an RF

demodulator to the COAXIAL

jack on this unit.

indicates S-video cables

indicates video cables

indicates coaxial cables

indicates optical cables

indicates right analog cables

indicates left analog cables

indicates signal direction

Video monitor

VCR 1 or VCR 2/

DVR (digital

video recorder)

Cable TV or

Satellite tuner

DVD player

TV/digital TV or

LD player

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM15

16

CONNECTIONS

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. When you connect components to

both the COAXIAL and OPTICAL jacks, priority is given

to the input signals from the COAXIAL jack. All digital

input jacks are acceptable for 96-kHz sampling digital

signals (see page 27 for details).

y

• You can designate the input for each digital jacks according to

your component by using “7 I/O ASSIGNMENT” on the SET

MENU (see pages 61 and 62 for details).

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM

or high-output MC cartridge. If you have a turntable with

a low-output MC cartridge, use an in-line boosting

transformer or MC-head amplifier when connecting to

these jacks.

y

• Connect your turntable to the GND terminal to reduce noise in

the signal. However you may hear less noise without the

connection to the GND terminal for some record players.

■ Connecting a CD player

y

• The COAXIAL CD and OPTICAL CD jacks are available for a

CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and

OPTICAL CD jacks, priority is given to the input signals from

the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

y

• DIGITAL OUTPUT jacks and analog OUT (REC) are

independent. Only digital signals are output from DIGITAL

OUTPUT jacks and analog signals from OUT (REC) jacks.

• When you connect your recording component to both the

analog and digital input and output jacks, the priority is given

to the digital signal.

Notes

• When you connect a recording component to this unit, keep its

power on while using this unit. If the power is off, this unit may

distort the sound from other components.

• When you record from a source component connected to this

unit while this unit is set in the standby mode, the recorded

sound may be distorted. To avoid this problem, turn on this

unit.

0103V2200_10-18_EN(U) 01.8.1, 9:43 AM16

Strona jest ładowana ...

Yamaha RX-V2200 Instrukcja obsługi

Yamaha RX-V2200 Instrukcja obsługi

w innych językach

Powiązane dokumenty