Seada SD-MV-0501 4K 5X1 Seamless Switcher Instrukcja obsługi
- Typ
- Instrukcja obsługi
4K 5x1 Seamless Switcher with Multiview
S h ow i n g t h e Wor l d
SD-MV-0501
4K 5X1 Seamless Switcher with Multiview
VER 1.0
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 1 E-mail: [email protected]
Warning
◼ Do not expose this device to Rain, Moisture, and Dripping
◼ Only use accessories specified by the manufacture
◼ Unplug this device during Lightning Storms
◼ The manual is for reference only, maybe updated without further notice
Content
1. FEATURES 2
2. PACKAGE CONTENTS 2
3. CONNECTORS AND CONTROLS 3
Front 3
Rear 3
4. EDID AND HDCP HANDLE 4
5. VIDEO AND AUDIO OUTPUT 4
6. MULTIVIEW 4
7. SPECIFICATION 5
8. RS232 COMMAND 5
HELP command 5
Firmware version command 5
Switching and Input command 5
Set output resolution command 6
Multiview command 7
Output HDCP command 9
EDID command 9
Video Keep Alive (VKA) command 9
4K-AUTO command 10
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 2 E-mail: sales@seada.co.uk
Introduction
SD-MV-0501 is a HDMI 2.0 and DP 1.2 Seamless Video Switcher with Multiview function. It
supports 3x HDMI, 1x DP and 1x USB-C (video only) inputs, one HDMI and one HDBaseT video
mirror output. One 3.5mm audio jacket can output analogue stereo audio. User can use Front
Buttons or RS232 commands to control the switcher
1. Features
• Seamless Switching on single display window mode
• Support 5 Multiview display modes
• Support HDMI 2.0, DP 1.2 input
• Scaling output with multiple resolution options, up to 4096x2160@60
• Extensive EDID and HDCP control
• HDBaseT transmission length up to 70m @1080p, or 40m @4K
• Support PCM and bitstream audio format up to 5.1 channel
• Audio extraction, 3.5mm L/R output
• Provide 24V/10watt PSE (POC) for HDBaseT receiver
• Support firmware upgrade with U disk by side of the switcher
2. Package Contents
Item
Quantity
Switcher Unit
1
24V/1A power adapter
1
3-way male captive screw connector
1
Download Card
1
Quick Start Manual
1
HDBaseT RX (only with Kit)
1
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 3 E-mail: sales@seada.co.uk
3. Connectors and Controls
Front
Name
Description
HDMI 1
Press HDMI 1 button to select HDMI 1 as the input source.
Long press it for 3 seconds to enter SINGLE mode, .
Note, when works on non-SINGLE mode, directly short press input
buttons will be invalid.
HDMI 2
Press HDMI 2 button to select HDMI 2 as the input source.
Long press it for 3 seconds to enter PIP Multiview mode, .
HDMI 3
Press HDMI 3 button to select HDMI 3 as the input source.
Long press it for 3 seconds to enter PBP Multiview mode, .
DP
Press DP button to select DP as the input source.
Long press it for 3 seconds to enter 3xWIN mode, .
USB-C
Press USB-C button to select USB-C (video only) as the input
Long press it for 3 seconds to enter 4xWIN mode, .
RESO
Press RESO (short for Resolution) button to select different output
resolution. The resolution info will be shown on screen.
Long press this button for 3 seconds the screen will show up one yellow
border on window 1. Continue press this button the border will be
shown on window 2 or 3… then press one input button such as HDMI 1,
and then HDMI 1 will be displayed on the current selected window.
Please note: Press HDMI 3 and DP at the same time can enable/disable AUTO SWITCH function
in SINGLE window display mode
Rear
Name
Description
HDBT out
HDBaseT Scaling output up to 3840x2160@60-4:2:0
Act as 24V POC-PSE
HDMI out
HDMI scaling output up to 3840x2160@60
LR out
3.5mm LR stereo audio output, 20Hz ~ 20kHz, 1.5Vrms max
INPUTs
HDMI 1, HDMI 2, HDMI 3, DP, USB-C
RS232
Baud Rate: 9600, Data Bits:8, Parity: None Stop Bits:1
3 way 3.5mm phoenix connector
TX means Switcher PC; RX means Switcher PC G means Ground
24V
24V power adapter to plug in
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 4 E-mail: sales@seada.co.uk
4. EDID and HDCP handle
The switcher support following EDID modes for source to detection, user can select it by RS232
command
Number
EDID mode
Number
EDID mode
1
4K60-2.0CH
9
1680x1050
2
4K60-5.1CH
10
1600x1200
3
4K30-2.0CH
11
1440x900
4
4K30-5.1CH
12
1360x768
5
1080P-2.0CH
13
1280x1024
6
1080P-5.1CH
14
1024x768
7
720P
15
AUTO
8
1920x1200
The switcher support 3 HDCP options for HDMI output setting
FORCE-1.4, FORCE-2.2, FORCE-OFF
The default selection is FORCE-1.4, User can select it by RS232 command
5. Video and Audio output
The switcher support following video output resolution
Number
Output Resolution
Number
Output Resolution
1
4096x2160p 60Hz
8
1920x1080p 60Hz
2
4096x2160p 50Hz
9
1920x1080p 50Hz
3
3840x2160p 60Hz
10
1360x768p 60Hz
4
3840x2160p 50Hz
11
1280x800p 60Hz
5
3840x2160p 30Hz
12
1280x720p 60Hz
6
3840x2160p 25Hz
13
1280x720p 50Hz
7
1920x1200P 60Hz RB
14
1024x768 60Hz
Audio output is always extracted from the source displayed on the window 1
6. Multiview
The Switcher support 5 Multiview display modes
SINGLE, PIP, PBP, 3xWIN, 4Xwin
Users can select different operations for different Multiview modes as following:
SINGLE and 4xWIN: Inputs selection
PBP and 3xWIN: Inputs selection, Display Ratio selection
PIP: Inputs selection, Display Ratio selection, Sub window size and position selection
Multiview window distribution as following
User can use RS232 commands to do detail window layout.
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 5 E-mail: sales@seada.co.uk
7. Specification
RS232
9600 baud rate, 8 data bits, 1 stop bit, no parity
Power Supply
24V/1A ,14W max
Operating Temperature
0 to +40°C (+32 to +104 °F)
Operating Humidity
10 to 50 % RH (non-condensing)
Dimensions
L225 x W100 x H25 mm
Mass (Main Unit)
0.75kg
8. RS232 command
Note: All the commands begin with SET or GET, end with Carriage Return (CR).
Represents Carriage Return (CR).
All return messages are always end with CR.
HELP command
This command returns the complete list of supported control commands
Command
Details
GET HELP
Get the Commands list
Example:
Send: GET HELP
Receive: Command list
Firmware version command
Command
Details
GET VERSION
Get firmware version
Example:
Send: GET VERSION
Receive: 20210824
Switching and Input command
The following commands are used for input selection or querying input information
These commands only be valid on SINGLE mode
Commands
Details
SET AUTO SWITCH w
w is ON or OFF, default OFF
Example:
Send: SET AUTO SWITCH ON
Receive: AUTO SWITCH ON
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 6 E-mail: sales@seada.co.uk
GET AUTO SWITCH
Return AUTO SWITCH setting status
Example:
Send: GET AUTO SWITCH
Receive: AUTO SWITCH ON
SET IN SOURCE w
w is one of the following:
HDMI1, HDMI2, HDMI3, DP, USB-C
Example:
Send: SET IN SOURCE HDMI1
Receive: IN SOURCE HDMI1
GET IN SOURCE
Get current source selection
Example:
Send: GET IN SOURCE
Receive: IN SOURCE HDMI1
GET IN RESOLUTION
Get current source resolution
Example:
Send: GET IN RESOLUTION
Receive: IN RESOLUTION 1920x1080p60
Set output resolution command
The following commands are used to select the output resolution:
Commands
Details
SET OUT RESOLUTION w
w is one of the following
4096x2160p60, 4096x2160p50,
3840x2160p60, 3840x2160p50,
3840x2160p30, 3840x2160p25,
1920x1200p60RB, 1920x1080p60,
1920x1080p50, 1360x768p60,
1280x800p60, 1280x720p60,
1280x720p50, 1024x768p60
Default: 3840x2160p60
Example:
Send: SET OUT RESOLUTION 3840x2160p60
Receive: OUT RESOLUTION 3840x2160p60
GET OUT RESOLUTION
Get current output resolution setting
Example:
Send: GET OUT RESOLUTION
Receive: OUT RESOLUTION 3840x2160p60
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 7 E-mail: sales@seada.co.uk
Multiview command
The following commands used to select Multiview modes, windows layout and so on
Commands
Details
SET MULTIVIEW w
Select one Multiview mode for current display
w is one of the following, default SINGLE
SINGLE,
PIP,
PBP,
3xWIN,
4xWIN,
Example:
Send: SET MULTIVIEW PIP
Receive: MULTIVIEW PIP
GET MULTIVIEW
Get the current Multiview mode
Example:
Send: GET MULTIVIEW
Receive: MULTIVIEW 3xWIN
SET WINDOWx IN y
Select one input for one display window for the current
Multiview mode. x is one of 1, 2, 3 or 4
y is one of the following:
HDMI1, HDMI2, HDMI3, DP, USB-C
Example:
Send: SET WINDOW1 IN HDMI1
Receive: WINDOW1 IN HDMI1
GET WINDOWx IN
This command to get which is the input source for one
display window for the current Multiview mode
Example:
Send: GET WINDOW1 IN
Receive: WINDOW1 IN HDMI1
SET PIP POS w
This command to select the PIP sub window position.
w is one of the following, default RightBottom
LeftTop, LeftBottom, RightTop, RightBottom
Example:
Send: SET PIP POS LeftTop
Receive: PIP POS LeftTop
GET PIP POS
This command to get the PIP sub window position
Example:
Send: GET PIP POS
Receive: PIP POS LeftTop
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 8 E-mail: sales@seada.co.uk
SET PIP SIZE w
This command to select the PIP sub window size.
w is one of the following, default LARGE
SMALL, MIDDLE, LARGE
Example:
Send: SET PIP SIZE SMALL
Receive: PIP SIZE SMALL
GET PIP SIZE
Get the PIP window size.
Example:
Send: GET PIP SIZE
Receive: PIP SIZE SMALL
SET PBP RATIO w
Set the PBP window display ratio
w is one of the following, default 2:1
2:1, 1:1
Example:
Send: SET PBP RATIO 1:1
Receive: PBP RATIO 1:1
GET PBP RATIO
Get the PBP window display ratio
Example:
Send: GET PBP RATIO
Receive: PBP RATIO 1:1
SET 3xWIN RATIO w
Set the 3xWIN window display ratio
w is one of 2:1 or 1:1, default 2:1
Example:
Send: SET 3xWIN RATIO 1:1
Receive: 3xWIN RATIO 1:1
GET 3xWIN RATIO
Get the 3xWIN window display ratio
Example:
Send: GET 3xWIN RATIO
Receive: 3xWIN RATIO 1:1
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 9 E-mail: sales@seada.co.uk
Output HDCP command
The following commands are used to select the HDMI Output HDCP modes:
Commands
Details
SET OUT HDCP w
w is one of following, default FORCE-OFF
FORCE-1.4,FORCE-2.2,FORCE-OFF
Example:
Send: SET OUT HDCP FORCE-1.4
Receive: OUT HDCP FORCE-1.4
GET OUT HDCP
Get the output current HDCP mode
Example:
Send: GET OUT HDCP
Receive: OUT HDCP FORCE-1.4
EDID command
The following commands are used to set EDID mode for the inputs
Commands
Details
SET IN EDIDMODE w
w is one of the following:
4K60-2.0, 4K60-5.1, 4K30-2.0, 4K30-5.1, 1080p60-2.0
1080p60-5.1, 1920x1200, 1680x1050, 1600x1200,
1440x900, 1360x768, 1280x1024, 1024x768, 720p, AUTO
Default: 4K60-2.0
Example:
Send: SET IN EDIDMODE 4K60-2.0
Receive: IN EDIDMODE 4K60-2.0
GET IN EDIDMODE
Get the current EDID mode
Example:
Send: GET IN EDIDMODE
Receive: IN EDIDMODE 4K60-2.0
Video Keep Alive (VKA) command
When there is no signal present, 3 options are available for selection:
Output blue screen, Output black screen, No timing output (VKA off)
Commands
Details
SET OUT VKA w
w is one of the following, default BLACKSCREEN
BLUESCREEN, BLACKSCREEN,NOTIMING
Example:
Send: SET OUT VKA BLUESCREEN
Receive: OUT VKA BLUESCREEN
GET OUT VKA
Get current VKA mode
Example:
Send: GET OUT VKA
Receive: OUT VKA BLUESCREEN
4K 5x1 Seamless Switcher with Multiview
Website: www.seada.co.uk 10 E-mail: sales@seada.co.uk
4K-AUTO command
If we set 4K output to a displayer which can’t support 4K, 4K-AUTO command can be enabled,
switcher will change the output resolution according to displayer’s capability
Commands
Details
SET OUT 4K-AUTO w
w is one of ON or OFF, default ON
Example:
Send: SET OUT 4K-AUTO ON
Receive: OUT 4K-AUTO ON
GET OUT 4K-AUTO
Get current OUT 4K-AUTO mode
Example:
Send: GET OUT 4K-AUTO
Receive: OUT 4K-AUTO ON
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
