Sony MDS-S39 Instrukcja obsługi

 1998 by Sony Corporation

3-862-110-51(1)

EN

Operating Instructions

Instrukcja obsługi

Инструкция по эксплуатации

PL

EN

RF

MDS-S39

MiniDisc Deck

2

EN

WARNING

To prevent fire or shock

hazard, do not expose the unit

to rain or moisture.

To avoid electrical shock, do

not open the cabinet. Refer

servicing to qualified

personnel only.

The laser component in this product is

capable of emitting radiation exceeding

the limit for Class 1.

This appliance is classified as a CLASS 1

LASER product. The CLASS 1 LASER

PRODUCT MARKING is located on the

rear exterior.

The following caution label is located

inside the unit.

Precautions

On safety

Should any solid object or liquid fall

into the cabinet, unplug the deck and

have it checked by qualified personnel

before operating it any further.

On power sources

• Before operating the deck, check that

the operating voltage of the deck is

identical with your local power

supply. The operating voltage is

indicated on the nameplate at the rear

of the deck.

• If you are not going to use the deck

for a long time, be sure to disconnect

the deck from the wall outlet. To

disconnect the mains lead, grasp the

plug itself; never pull the cord.

• The mains switch is located on the

rear exterior.

• Mains lead must be changed only at

the qualified service shop.

On placement

Do not install the appliance in a

confined space, such as a bookcase or

built-in cabinet because the mains

power switch (MAIN POWER) is

located on the rear exterior.

On operation

If the deck is brought directly from a

cold to a warm location, or is placed in a

very damp room, moisture may

condense on the lenses inside the deck.

Should this occur, the deck may not

operate properly. In this case, remove

the MD and leave the deck turned on

for about an hour until the moisture

evaporates.

On the MiniDisc cartridge

• Do not open the shutter to expose the

MD.

• Do not place the cartridge where it

will be subject to extremes of

sunlight, temperature, moisture or

dust.

On cleaning

Clean the cabinet, panel and controls

with a soft cloth slightly moistened with

a mild detergent solution. Do not use

any type of abrasive pad, scouring

powder or solvent such as alcohol or

benzine.

If you have any questions or problems

concerning your deck, please consult

your nearest Sony dealer.

Welcome!

Thank you for purchasing the Sony

MiniDisc Deck. Before operating the

deck, please read this manual

thoroughly and retain it for future

reference.

About This Manual

Conventions

• Controls in the instructions are those

on the deck; these may, however, be

substituted by controls on the remote

that are similarly named or, when

different, appear in the instructions

within brackets.

• The following icons are used in this

manual:

Z

Indicates a procedure that

requires use of the remote.

z

Indicates tips for making the

task easier and hints.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF

ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM

ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

EN

3

EN

TABLE OF CONTENTS

Getting Started

Unpacking ........................................................................................................................... 4

Hooking Up the System.................................................................................................... 4

Recording on an MD.......................................................................................................... 6

Playing an MD ....................................................................................................................... 8

Recording on MDs

Notes on Recording ........................................................................................................... 9

Useful Tips for Recording ................................................................................................ 9

Recording Over Existing Tracks..................................................................................... 11

Adjusting the Recording Level....................................................................................... 11

Marking Track Numbers while Recording (Track Marking) .................................... 12

Starting Recording with 6 Seconds of Prestored Audio Data

(Time Machine Recording) .......................................................................................... 13

Synchro-Recording with Audio Equipment of Your Choice .................................... 14

Synchro-Recording with a Sony CD Player ................................................................. 14

Recording on an MD Using a Timer.............................................................................. 16

Playing MDs

Using the Display.............................................................................................................. 17

Locating a Specific Track ................................................................................................. 18

Locating a Particular Point in a Track ........................................................................... 19

Playing Tracks Repeatedly .............................................................................................. 20

Playing in Random Order (Shuffle Play) ...................................................................... 21

Creating Your Own Programme (Programme Play) .................................................. 21

Useful Tips when Recording from MDs to Tape ........................................................ 22

Playing an MD Using a Timer ........................................................................................ 23

Editing Recorded MDs

Notes on Editing ............................................................................................................... 24

Erasing Recordings (Erase Function) ............................................................................ 24

Erasing a Portion of a Track (A-B Erase Function) ..................................................... 25

Dividing Recorded Tracks (Divide Function).............................................................. 26

Combining Recorded Tracks (Combine Function) ..................................................... 27

Moving Recorded Tracks (Move Function).................................................................. 28

Labelling Recordings (Title Function)........................................................................... 29

Undoing the Last Edit (Undo Function) ....................................................................... 31

Additional Information

Display Messages.............................................................................................................. 32

System Limitations ........................................................................................................... 32

Troubleshooting ................................................................................................................ 33

Specifications ..................................................................................................................... 34

Beep Output During Operations .................................................................................... 35

Guide to the Serial Copy Management System ........................................................... 36

Index .......................................................................................................................................... 38

Getting Started

4

EN

ç

Ç

REC

OUT

TAPE

IN

DIGITAL

OUT

DIGITAL

OUT

DIGITAL

IN

L I N E

(ANALOG)

D I G I T A L

IN

OUT

L

R

IN

OUT

B E E P

ON

OFF

Getting Started

çç

ç : Signal flow

to a wall outlet

(or to a timer during timer

recording or playback)

White

(L)

Red

(R)

White

(L)

Red

(R)

Amplifier

CD player

DAT deck or

MD deck, etc.

Connect only

one digital

component at

a time.

Unpacking

Check that you received the following items:

• Audio connecting cords (2)

• Optical cable (1)

• Remote commander (remote) RM-D27M (1)

• Sony SUM-3 (NS) batteries (2)

Inserting batteries into the remote

You can control the deck using the supplied remote.

Insert two R6 (size-AA) batteries by matching the +

and – on the batteries. When using the remote, point it

at the remote sensor g on the deck.

z When to replace batteries

With normal use, the batteries should last for about six

months. When the remote no longer operates the deck,

replace all the batteries with new ones.

Notes

• Do not leave the remote near an extremely hot or humid

place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from

battery leakage and corrosion.

Hooking Up the System

Overview

This section describes how to hook up the MD deck to

an amplifier or other components such as a CD player

or DAT deck. Be sure to turn off the power of each

component before connection.

What cords will I need?

• Audio connecting cords (supplied) (2)

• Optical cables (only one supplied) (2)

Getting Started

5

EN

DIGITALDIGITAL

OUTIN

OPTICAL

ç

Ç

ç

Ç

TAPE/MD

L

R

L

R

INOUT

IN

OUT

LINE

(ANALOG)

Hookups

Connecting the deck to an amplifier

Connect the amplifier to the LINE (ANALOG) IN/OUT

jacks using the audio connecting cords (supplied), making

sure to match the colour-coded cords to the appropriate

jacks on the components: red (right) to red and white (left) to

white. Be sure to make connections firmly to prevent hum

and noise.

Connecting the deck to a digital component such as a CD

player, DAT deck, digital amplifier, or another MD deck

Connect the component through the DIGITAL IN/OUT

connectors with two optical cables (only one supplied).

Take the caps off the connectors and then insert the plugs

parallelly until they click into place.

Be sure not to bend or tie together the optical cables.

z Automatic conversion of digital sampling rates

during recording

A built-in sampling rate converter automatically

converts the sampling frequency of various digital

sources to the 44.1 kHz sampling rate of your MD deck.

This allows you to record sources such as 32- and 48-

kHz DAT or satellite broadcasts, as well as compact

discs and other MDs.

Notes

• If “Din Unlock” or “Cannot Copy” appears in the display,

recording through the digital connector is not possible.

In this case, record the programme source through the

LINE (ANALOG) IN jacks with INPUT set to ANALOG.

• When recording through the DIGITAL IN connector, you

cannot adjust the recording level.

çç

ç: Signal flow

MD deck

Amplifier

çç

ç: Signal flow

MD deck Digital component

Connecting the mains lead

Connect the mains lead to a wall outlet or to the outlet

of a timer.

Turning on the unit

Set MAIN POWER on the rear of the unit to ON.

The unit is turned on in standby mode.

MAIN POWER

ONOFF

MAIN

POWER

Basic Operations

6

EN

MONO

4

Set INPUT to the corresponding input connector.

5

Set REC MODE to the mode you want to record in.

With the arrow

pointing this way

With the label side up

If the MD has a recorded material on it, the deck will

automatically start recording from the end of the last recorded

track.

To record through Set INPUT to

LINE (ANALOG) IN

DIGITAL

ANALOG

DIGITAL IN

To record in Set REC MODE*

1

to

Monaural sound*

2

STEREOStereo sound

*

1

If you switch REC MODE during recording or recording pause, recording

stops.

*

2

In the monaural recording, you can record about two times longer than in

the stereo recording.

Monitor audio during recording

Even if you set REC MODE to

MONO, the monitor signal does

not become monaural.

1

Turn on the amplifier and play the programme source you

want to record.

2

Press 1/u.

The STANDBY indicator turns off.

3

Insert a recordable MD.

•

REC LEVEL

(ANALOG)

AMS

PUSH ENTER

0

10

p

·∏

•

REC MODE

INPUT

EDIT/NO YES

STEREO

MONO

ANALOG

REPEAT

DISPLAY/CHAR

SCROLL

PLAY MODE

TIMER

PHONES

LEVEL

REC OFF PLAY

MIN

MAX

r

)

0

§

=

+



DIGITAL

STANDBY

32 68

457

Recording on an MD

Basic Operations

7

EN

6

Press r.

The deck becomes ready to record.

7

When recording the analog input signal, adjust the recording

level with REC LEVEL.

The fourth dot is satisfactory for most purposes. For details,

refer to “Adjusting the Recording Level” on page 11.

8

Press ﬂ (or ·).

Recording starts.

9

Start playing the programme source.

Do not disconnect the deck from the power source immediately after

recording

If you do, recorded material may not be saved to the MD. To save the material,

after recording, press § to take out the MD or change the deck to standby by

pressing

1/u

. “TOC” will flash in the display at this time.

After “TOC” stops flashing and goes out, you can pull out the mains lead.

To

Press

Stop recording

Pause recording* ﬂ (or P). Press the button again to

resume recording.

p

Take out the MD § after stopping recording

* Whenever you pause recording, the track number increases by one. For example, if

you paused recording while recording on track 4, the track number increases by

one and recording continues on the new track when restarted.

To protect an MD against accidental erasure

To make it impossible to record on an MD, slide the tab in the direction of

arrow, opening the slot. To allow recording, close the slot.

Rear of the disc

Slide the tab in

the direction of arrow

Record-protect tab

When ”TOC“ flashes in the

display

The deck is currently updating the

Table Of Contents (TOC).

Do not move the deck or pull out

the mains lead. Changes to an MD

made through recording are saved

only when you update the TOC by

ejecting the MD or changing the

deck to standby by pressing 1/u.

Basic Operations

8

EN

4

Press ﬂ (or ·).

The deck starts playing. Adjust the volume on the amplifier.

Playing an MD

z You can locate and play back

a track while the deck is

stopped

1 Turn AMS (or press =

or +) until the number

of the track you want to

play appears.

2 Press AMS or ﬂ (or ·).

z To use headphones

Connect them to PHONES

jack. Use PHONES LEVEL

to adjust the volume.

Adjust the

headphone

volume.

Connect the

headphones.

Pause playing

Stop playing

Do the following:

Press p.

Press ﬂ (or P). Press the button again

to resume playing.

To

Turn AMS counterclockwise (or press

= on the remote).

Go to the preceding track

Go to the next track

Turn AMS clockwise (or press + on

the remote).

Press § after stopping playing.

Take out the MD

With the arrow

pointing this way

With the label side up

1

Turn on the amplifier and set the source selector to the position

for MD deck.

2

Press 1/u.

The STANDBY indicator turns off.

3

Insert an MD.

•

REC LEVEL

(ANALOG)

AMS

PUSH ENTER

0

10

p

·∏

•

REC MODE

INPUT

EDIT/NO YES

STEREO

MONO

ANALOG

REPEAT

DISPLAY/CHAR

SCROLL

PLAY MODE

TIMER

PHONES

LEVEL

REC OFF PLAY

MIN

MAX

r

)

0

§

=

+



DIGITAL

STANDBY

32 4

9

EN

Recording on MDs

The MD deck uses the SCMS (Serial Copy Management

System on page 36)

MDs recorded through digital input connector cannot be

copied onto other MDs or DAT tapes through the digital

output connector.

When recording digital signals that have been emphasized

(in the higher frequencies)

The signal is automatically de-emphasized (with attenuation

proportional to the degree of emphasis) and the level of the

de-emphasized signal is indicated on the peak level meters.

When the deck is recording or in recording pause, digital

signals input through DIGITAL IN are output to DIGITAL

OUT with the same sampling rate.

To change the digital input signal to another sampling rate

for output (without recording it to an MD), use Input

Monitor Function (see page 10).

•

p

·∏

•

r

)

0

§

=

+



DISPLAY/CHAR

Recording on MDs

Useful Tips for Recording

Checking the remaining recordable time on

the MD

• When you press DISPLAY/CHAR while recording,

the remaining recordable time on the MD appears.

• When you press DISPLAY/CHAR repeatedly while

the deck is stopped, the display changes as follows:

total recorded time, remaining recordable time on

the MD, disc name (see page 17).

(Continued)

Notes on Recording

If “Protected” appears in the display

The MD is record-protected. Close the slot to record on the

disc (see “To protect an MD against accidental erasure” on

page 7).

If “Din Unlock” flashes in the display

• The digital programme source is not connected as you set

with INPUT in Step 4 on page 6.

To continue, connect the programme source properly.

• The programme source is not on.

Turn on the programme source.

Depending on source being recorded, track numbers are

marked in following ways:

• When recording from a CD or MD with INPUT at

DIGITAL and the source connected through DIGITAL IN:

The deck automatically marks track numbers in the same

sequence as the original. If, however, a track is repeated

two or more times (e.g. by single-track repeat play) or two

or more tracks with the same track number (e.g. from

different MDs or CDs) are played, the track or tracks are

recorded as part of a single, continuous track with a single

track number.

If the source is an MD, track numbers may not be marked

for tracks of less than 4 seconds.

• When recording with INPUT at DIGITAL the deck may

not automatically mark track numbers for some CD

players and multi disc players. In these cases, mark the

track numbers afterwards using the deck’s Divide

Function (see “Dividing Recorded Tracks” on page 26).

• When recording from source connected through LINE

(ANALOG) IN with INPUT at ANALOG, and “LEVEL-

SYNC” does not light up (see “Marking Track Numbers

while Recording” on page 12) or when recording from

DAT or satellite broadcasts connected through DIGITAL

IN with INPUT at DIGITAL:

The source will be recorded as a single track. You can

divide the track afterwards using the Divide Function on

page 26 or mark track numbers during recording by using

the Track Marking Function on page 12.

If “LEVEL-SYNC” appears in the display, the deck

automatically marks track numbers when recording

analog source or digital recording of DAT or satellite

broadcasts (see “Marking track numbers automatically”

on page 12).

• When recording from DAT or satellite broadcasts with

INPUT at DIGITAL, the deck automatically marks a track

number whenever the sampling frequency of the input

signal changes.

When “TOC” flashes in the display

The deck is currently updating the Table Of Contents (TOC).

Do not move the deck or pull out the mains lead. Changes

to an MD made through recording are saved only when you

update the TOC by ejecting the MD or changing the deck to

standby by pressing 1/u.

Recording on MDs

10

EN

Monitoring the input signal (Input Monitor)

Before starting recording, you can monitor the selected

input signal through the deck’s output connectors.

1 Press § to remove the MD.

2 Set INPUT according to the input signal you want

to monitor.

When INPUT is at ANALOG

The analog signal input through LINE (ANALOG) IN is

output to DIGITAL OUT after A/D conversion, and

then to the LINE (ANALOG) OUT connectors and

PHONES jack after D/A conversion.

When INPUT is at DIGITAL

The digital signal input through DIGITAL IN is output

to DIGITAL OUT after passing through the sampling

rate converter, and then to the LINE (ANALOG) OUT

connectors and PHONES jack after D/A conversion.

Note

Even if you set REC MODE to MONO, the monitor

signal does not become monaural.

3 Press r.

If INPUT is at ANALOG, “AD-DA” appears in the

display.

If INPUT is at DIGITAL, “-DA”appears in the

display.

If “Auto Cut” appears in the display

(Auto Cut)

There has been no sound input for 30 seconds while

INPUT is set to DIGITAL and the source is connected

through DIGITAL IN. The 30 seconds of silence are

replaced by a blank of about 3 seconds and the deck

changes to recording pause.

z You can turn off the Auto Cut Function

For details, see “If “Smart Space” appears in the

display”.

If “Smart Space” appears in the display

(Smart Space)

There has been an extended silence of 4 to 30 seconds

in length when INPUT is set to DIGITAL and the

source is connected through DIGITAL IN.

The silence is replaced with a blank of about 3 seconds

and the deck continues recording. Note that the tracks

before and after this three-second space may be

recorded as a single track with a single track number.

To turn off the Smart Space Function and Auto Cut

Function

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES.

3 Press EDIT/NO to display “S. Space OFF.”

To turn on the Smart Space Function and Auto Cut

Function again

1 During recording pause, press EDIT/NO repeatedly until

“S. Space ?” appears in the display.

2 Press YES twice to display “S. Space ON”.

Notes

• When you turn off the Smart Space Function, the Auto Cut

Function is also turned off automatically.

• The Smart Space Function and Auto Cut Function are

factory set to on.

• The Smart Space Function does not affect the order of the

track numbers being recorded, even if the blank space

occurs in the middle of a track.

• If you turn off the deck or disconnect the mains lead, the

deck will recall the last setting (on or off) of the Smart

Space and Auto Cut Functions the next time you turn on

the deck.

Playing back tracks just recorded

Do this procedure to immediately play back tracks that

have just been recorded.

Press ﬂ (or ·) immediately after stopping

recording.

Playback starts from the first track of the material just

recorded.

To play from the first track of the MD after recording

1 Press p again after stopping recording.

2 Press ﬂ (or ·).

Playback starts from the first track of the MD.

11

EN

Recording on MDs

Recording Over Existing Tracks

Follow the procedure below to record over existing

material just as you would on an analog cassette tape.

1 Do Steps 1 to 5 in “Recording on an MD” on page

6.

2 Turn AMS (or press = or +) until the

number of the track to be recorded over appears.

3 To record from the start of the track, continue

from Step 6 in “Recording on an MD” on page 7.

z While “TRACK” flashes in the display

The deck is recording over an existing track, and stops

flashing when it reaches the end of the recorded

portion.

z To record from the middle of the track

1 After Step 2 above, press ﬂ (or ·) to start

playback.

2 Press ﬂ (or P) where you want to start recording.

3 Continue from Step 6 in “Recording on an MD” on

page 7.

Note

You cannot record from the middle of an existing track when

the “PROGRAM” or “SHUFFLE” is on.

Adjusting the Recording Level

When recording with INPUT at ANALOG and the

signal input through LINE (ANALOG) IN jacks, use

REC LEVEL to adjust the recording level before

starting recording.

You cannot adjust the recording level during digital

recording.

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 6 and 7.

2 Play the portion of the programme source with

the strongest signal level.

3 While monitoring the sound, turn REC LEVEL to

adjust the recording level so that the peak level

meters reach their highest point without turning

on the OVER indication. Occasional lighting of

“OVER” is acceptable.

4 Stop playing the programme source.

5 To start recording, do the procedure starting from

Step 8 in “Recording on an MD” on page 7.

Without turning on the OVER indication

=/+

r

6

)0

+=

pP·

= AMS +

•

p

·∏

•

r

)

0

§

=

+



•

p

·∏

•

r

)

0

§

=

+



REC LEVEL

Recording on MDs

12

EN

Marking Track Numbers while

Recording (Track Marking)

You can mark track numbers either manually or

automatically. By marking track numbers at specific

points, you can quickly locate the points later using the

AMS Function or Editing Functions.

1 Press EDIT/NO to display “LevelSync ?”during

recording or recording pause.

2 Press YES twice to display “LevelSync ON.”

“LEVEL-SYNC” appears in the display.

To cancel Automatic Track Marking

1 Press EDIT/NO during recording or recording pause.

“LevelSync ?” appears in the display.

2 Press YES.

3 Press EDIT/NO.

“LevelSyncOFF” appears in the display.

* The signal level must remain low for 2 or more seconds

before a new track number is marked.

z When you want to mark track numbers after you‘ve

finished recording

Use the Divide Function (see “Dividing Recorded

Tracks” on page 26).

Note

If you turn off the deck or disconnect the mains lead, the

deck will recall the last setting (LevelSync on or off) of the

Automatic Track Marking Function the next time you turn

on the deck.

Marking track numbers manually

(Manual Track Marking)

You can mark track numbers at any time while

recording on an MD.

Press r at the place you want to add a track mark

while recording.

Marking track numbers automatically

(Automatic Track Marking)

The deck adds track marks differently in the following

cases:

• When recording from CDs or MDs with INPUT at

DIGITAL and the source connected through

DIGITAL IN:

The deck marks track numbers automatically. When

you record from a CD or MD, the track numbers are

marked as they are found on the original. However,

the deck may not automatically mark track numbers

for some CD players and multi disc players.

• When recording with INPUT at ANALOG and the

source connected through LINE (ANALOG) IN, or

when recording from DAT or satellite broadcasts

with INPUT at DIGITAL and the DAT or satellite

broadcasts connected through DIGITAL IN:

The deck marks a new track number whenever the

signal level drops and rises to a certain point*

(Automatic Track Marking). If “LEVEL-SYNC” does

not light up, set the LevelSync to ON as follows:

•

p

·∏

•

r

)

0

§

=

+



YESEDIT/NO

r

13

EN

Recording on MDs

3 Press AMS (or T.REC) to start Time Machine

Recording.

Recording of the programme source starts with

the 6 seconds of audio data stored in the buffer

memory.

z To stop Time Machine Recording

Press p.

Note

The deck starts storing audio data when the deck is in

recording pause and you start playing the programme

source. With less than 6 seconds of playing of the

programme source and audio data stored in the buffer

memory, Time Machine Recording starts with less than

6 seconds of audio data.

Starting Recording with

6 Seconds of Prestored Audio

Data (Time Machine Recording)

When recording from an FM or satellite broadcast, the

first few seconds of material are often lost due to the

time it takes you to ascertain the contents and press the

record button. To prevent the loss of this material, the

Time Machine Recording Function constantly stores

6 seconds of the most recent audio data in a buffer

memory so that when you begin recording the

programme source, the recording actually begins with

the 6 seconds of audio data stored in the buffer

memory in advance, as shown in the illustration below:

1 Do Steps 1 to 6 in “Recording on an MD” on

pages 6 and 7.

The deck changes to recording pause.

2 Start playing the programme source you want to

record.

The most recent 6 seconds of audio data is stored

in the buffer memory.

End of the programme

source to be recorded

Time

Recorded

portion

When you press

AMS in Step 3

Audio data in 6-second buffer memory

Beginning of the programme

source to be recorded

r

6

)0

+=

pP·

T.REC

= AMS +

•

p

·∏

•

r

)

0

§

=

+



Recording on MDs

14

EN

Synchro-Recording with Audio

Equipment of Your Choice Z

By using the MUSIC SYNC button on the remote, you

can automatically start recording in sync with the

signal input from the programme source through the

LINE (ANALOG) IN jacks or the DIGITAL IN

connector (Music Synchro-Recording).

The method of marking track numbers differs,

depending on the programme source being recorded

and how the deck is connected to the programme

source. (See “Notes on Recording” on page 9.)

1 Do Steps 1 to 5 in “Recording on an MD” on page

6.

2 Press MUSIC SYNC.

The deck changes to recording pause.

3 Start playing the programme source you want to

record.

The deck starts recording automatically.

z To stop Music Synchro-Recording

Press p.

Note

When Music Synchro-Recording, the Smart Space Function

and the Auto Cut Function turn on automatically regardless

of their setting (on or off) and type of input (digital or

analog).

Synchro-Recording with a Sony

CD Player Z

By connecting your deck to a Sony CD player or Hi-Fi

Component System, you can easily dub CDs onto MDs

using the CD synchro buttons on the remote. If your

deck is connected to a Sony CD player by a digital

input cable, track numbers are automatically marked

as appear on the original regardless of whether

“LevelSync ON” or “LevelSyncOFF” is selected. If

your deck is connected to a Sony CD player by audio

connecting cords through LINE (ANALOG) IN, track

numbers are automatically marked when you select

“LevelSync ON” (see “Marking Track Numbers while

Recording” on page 12).

As the same remote controls both the CD player and

the deck, you may have trouble operating both units if

they are far from each other. If you do, place the CD

player close to this deck.

1 Set the source selector on the amplifier to CD.

2 Do Steps 2 to 5 in “Recording on an MD” on page

6 to prepare the deck for recording.

3 Insert a CD into the CD player.

4 Select the playback mode (Shuffle Play,

Programme Play, etc.) on the CD player.

r

6

)0

+=

pP·

MUSIC SYNC

r

6

)0

+=

+=P

pP·

STOP

CD PLAYER P

START

STANDBY

15

EN

Recording on MDs

z

You can also do synchro-recording with a Sony video

CD player

Using the procedure for synchro-recording with a Sony

CD player, you can do synchro-recording with a Sony

video CD player also.

To select the video CD player, press button number 2

while pressing down the 1/u button before starting the

procedure.

To select the CD player again, press button number 1

while pressing down the 1/u button.

The deck is factory set to a CD player for synchro-

recording.

z You can check the remaining recordable time on the

MD

Press DISPLAY (see page 17).

5 Press STANDBY.

The CD player pauses for playing and the deck

pauses for recording.

6 Press START.

The deck starts recording and the CD player starts

playback.

The track number and elapsed recording time of

the track appear in the display.

If the CD player does not start playing

Some CD player models may not respond when you

press START on the remote of the deck. Press P on the

remote of the CD player instead.

7 Press STOP to stop synchro-recording.

To pause recording

Press STANDBY or CD PLAYER P.

To restart recording, press START or CD PLAYER P.

A new track number is marked each time you pause

recording.

Note

When using the supplied remote for synchro-recording, set

the mode selector on the CD player to CD1.

z You can use the remote of the CD player during

synchro-recording

When you press p, the CD player stops and the deck

pauses for recording.

When you press P, the CD player pauses and the deck

pauses for recording.

To restart synchro-recording, press ·.

z You can change CDs during synchro-recording

Do the following steps instead of Step 7 above.

1 Press p on the remote of the CD player.

The deck pauses for recording.

2 Change the CD.

3 Press · on the remote of the CD player.

Synchro-recording restarts.

Recording on MDs

16

EN

Recording on an MD Using a

Timer

By connecting a timer (not supplied) to the deck, you

can start and stop recording operations at specified

times. For further information on connecting the timer

and setting the starting and ending times, refer to the

instructions that came with the timer.

1 Do Steps 1 to 7 in “Recording on an MD” on

pages 6 and 7.

2 • If you want to specify the time for the start of

recording, press p.

• If you want to specify the time for the end of

recording, do Steps 8 and 9 of “Recording on an

MD” on page 7.

• If you want to specify the time for both start

and end of recording, press p.

3 Set TIMER on the deck to REC.

4 Set the timer as required.

• When you have set the time for the start of

recording, the deck turns off. When the

specified time arrives, the deck turns on and

starts recording.

• When you have set the time for the end of

recording, recording continues. When the

specified time arrives, the deck stops recording

and turns off.

• When you have set the time for both the start

and end of recording, the deck turns off. When

the starting time arrives, the deck turns on and

starts recording. When the ending time arrives,

the deck stops recording and turns off.

5 After you have finished using the timer, set

TIMER on the deck to OFF. Then place the deck

in standby status by plugging the mains lead of

the deck into a wall outlet or set the timer to

continuous operation.

• If TIMER is left at REC, the deck will

automatically start recording the next time you

turn the deck on.

• If you do not change the deck to standby status

for more than a month after timer recording has

finished, the recorded contents may disappear.

Make sure to change the deck to standby status within a

month after timer recording is completed

The TOC on the MD is updated and recorded contents are

written to the MD when you turn the deck on. If the

recorded contents have disappeared, “STANDBY” flashes

when you turn the deck on.

Notes

• It may take about 30 seconds after the deck is turned on

until recording starts. When recording at a specified time

using the timer, be sure to take this time into account

when setting the recording start time.

• During timer recording, new material is recorded from the

end of the recorded portion on the MD.

• Material recorded during timer recording will be saved to

the disc the next time you turn the deck on. “TOC” will

flash in the display at that time. Do not move the deck or

pull out the mains lead while “TOC” is flashing.

• Timer recording will stop if the disc becomes full.

•

p

·∏

•

r

)

0

§

=

+



TIMER

p

17

EN

Playing MDs

When you insert an MD, the disc name, total number

of tracks, and total disc playing time appear in the

display as follows:

Total number of tracks Total disc playing time

The disc name appears, followed by the total number

of tracks (Tr) and total disc playing time.

A music calendar showing all the track numbers

appears within a grid if the MD is a premastered disc,

or without a grid if the MD is a recordable disc.

If the total track number exceeds 25, z appears to the

right of number 25 in the music calendar.

To label a recordable disc and its tracks, see

“Labelling Recordings” on page 29.

Note

When you insert a new MD or turn off the deck and turn it

on again, the last item displayed will reappear.

If, however, you disconnect the mains lead, the display will

show the total track number and total playing time of all

recorded tracks the next time you turn on the deck, no

matter what the last display was.

(Continued)

Disc name Music calendar

Checking the total track number, total disc

playing time, remaining recordable time of

the disc and the title of the disc

Each time you press DISPLAY/CHAR (or DISPLAY)

while the deck is stopped, you can change the display

as follows:

Remaining recordable time of the disc

(Recorded MDs only)

Disc name

Press

The remaining recordable time of the disc

is not shown for premastered MDs.

Press

Total track number and total playing

time of all recorded tracks

6

pP·

SCROLLDISPLAY

√

•

p

·∏

•

r

)

0

§

=

+



SCROLL

DISPLAY/CHAR

Playing MDs

Using the Display

You can use the display to check disc and track

information such as the total track number, total

playing time of the tracks, remaining recordable time

of the disc and disc name.

18

EN

Playing MDs

Locating a Specific Track

You can quickly locate any track while playing a disc

by using AMS (Automatic Music Sensor), = and

+, number buttons or M.SCAN on the remote.

z You can check the track name at any time while

playing an MD

Press SCROLL.

Since the display shows up to 12 characters at a time,

press SCROLL again to see the rest of the track title if

the title has 13 characters or more.

Press SCROLL again to pause scrolling, and again to

continue scrolling.

Do the following:

The next or

succeeding tracks

During playback, turn AMS clockwise

(or press + repeatedly) until you

find the track.

The current or

preceding tracks

During playback, turn AMS

counterclockwise (or press =

repeatedly) until you find the track.

A specific track

directly

Z

Press number buttons to enter the

track number.

A specific track by

using AMS

1 Turn AMS until the track number

you want to locate appears while

the deck is stopped. (The track

number is flashing.)

2 Press AMS or ﬂ.

To locate

By scanning each

track for 6 seconds

(music scan)

Z

1 Press M.SCAN before you start

playing.

2 When you find the track you want,

press · to start playing.

Number

buttons

Checking remaining time and the title of a

track

Each time you press DISPLAY/CHAR (or DISPLAY)

while playing an MD, you can change the display as

shown below. The track numbers in the music

calendar disappear after they are played.

Track number and playing time of the

current track

Track number and remaining time of

the current track

Press

Track name

Press

If no title is recorded, “No Name” appears,

followed by the elapsed playing time.

√

r

6

)0

+=

pP·

M.SCAN

>25

·

=/+

•

p

·∏

•

r

)

0

§

=

+



= AMS +

19

EN

Playing MDs

Locating a Particular Point in a

Track

You can also use 0 and ) to locate a particular

point in a track during playback or playback pause.

To locate a point Press

While monitoring the

sound

) (forward) or 0 (backward)

and keep pressing until you find

the point.

Quickly by observing

the display during

playback pause

) or 0 and keep pressing

until you find the point. There is

no sound output during this

operation.

Notes

• If the disc reaches the end while you are pressing )

during playback pause, “OVER” appears in the display.

Press 0 (or =) or turn AMS counterclockwise to go

back.

• If the disc reaches the end while you are pressing )

during sound monitoring, the deck stops.

• Tracks that are only a few seconds long may be too short

to scan using the search function. For such tracks, it is

better to play the MD at normal speed.

z When you directly locate a track with a number over

25 Z

You must press >25 first, before entering the

corresponding digits.

Press >25 once if it is a 2-digit track number, and twice

if it is a 3-digit track number.

To enter “0,” press button 10.

Examples: • To play track number 30

Press >25 once, then 3 and 10.

• To play track number 100

Press >25 twice, then 1, 10 and 10.

z You can extend the playing time during music scan

Z

While the deck is stopped, press M.SCAN repeatedly

until the playing time you want (6, 10 or 20 seconds)

appears in the display. Each press changes the time in

order of 6 to 20, then from 6 again.

z To pause playing at the beginning of a track

Turn AMS (or press = or +) after pausing

playback.

z To go quickly to the beginning of the last track

Turn AMS counterclockwise (or press =) while the

display shows the total track number and total disc

playing time, remaining recordable time of the disc, or

disc name (see page 17).

•

p

·∏

•

r

)

0

§

=

+



0/)

20

EN

Playing MDs

Playing Tracks Repeatedly

You can play tracks repeatedly in any play mode.

Press REPEAT.

“REPEAT” appears in the display.

The deck repeats the tracks as follows:

When the MD is

played in

Normal play (page 8)

Shuffle Play (page 21)

Programme Play (page 21)

The deck repeats

All the tracks

To cancel repeat play

Press REPEAT several times until “REPEAT” disappears.

The deck returns to the original playing mode.

Repeating the current track

While the track you want to repeat is playing in

normal play, press REPEAT several times until

“REPEAT 1” appears in the display.

Repeating a specific portion (A-B Repeat)

Z

You can play a specific portion of a track repeatedly.

This might be useful when you want to memorize

lyrics.

Note that you can only repeat a portion within the

boundaries of a single track.

1 While playing a disc, press A˜B at the starting

point (point A) of the portion to be played

repeatedly.

“REPEAT A-” flashes in the display.

2 Continue playing the track or press ) until you

reach the ending point (point B), then press A˜B

again.

“REPEAT A-B” lights continuously. The deck

starts to play the specified portion repeatedly.

To cancel A-B Repeat

Press REPEAT or p.

Setting new starting and ending points

You can repeat the portion immediately after the currently

specified portion by changing the starting and ending

points.

1 Press A˜B while “REPEAT A-B” appears.

The current ending point B becomes the new starting

point A and “REPEAT A-” flashes in the display.

2 Continue playing the track or press ) until you reach

the new ending point (point B), then press A˜B again.

“REPEAT A-B” lights continuously and the deck starts

playing repeatedly the newly specified portion.

Note

If you turn off the deck or disconnect the mains lead, the

deck will recall the last setting of the Repeat Function the

next time you turn on the deck.

The A-B Repeat settings, however, are lost.

All the tracks in random order

The same programme

r

6

)0

+=

pP·

REPEAT

A˜B

)

•

REPEAT

Strona jest ładowana ...

Sony MDS-S39 Instrukcja obsługi

Sony MDS-S39 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty