Hikoki DH28PD Instrukcja obsługi

Rotary Hammer

Bohrhammer

Σφυροδραπανο περιςτροφικο

Młotowiertarka

Fúrókalapács

Vrtací kladivo

Kırıcı delici

Ciocan rotopercutor

Vrtalno rušilno kladivo

Handling instructions

Bedienungsanleitung

Οδηγίες χειρισμού

Instrukcja obsługi

Kezelési utasítás

Návod k obsluze

Kullanım talimatları

Instrucţiuni de utilizare

Navodila za rokovanje

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Διαβάστε προσεκτικά και κατανοήσετε αυτές τις οδηγίες πριν τη χρήση.

Przed użytkowaniem należy dokładnie przeczytać niniejszą instrukcję i zrozumieć jej treść.

Használat előtt olvassa el ﬁ gyelmesen a használati utasítást.

Před použitím si pečlivě přečtěte tento návod a ujistěte se, že mu dobře rozumíte.

Aleti kullanmadan önce bu kılavuzu iyice okuyun ve talimatları anlayın.

Înainte de utilizare, citiţi cu atenţie şi înţelegeţi prezentele instrucţiuni.

Pred uporabo natančno preberite in razumite ta navodila.

DH 28PD

2

12

3 4

56

78

3

9 10

11 12

13 14

15 16

4

17 18

19 20

21 22

23 24

5

25 26

27 28

29 30

6

31

32

7

English Deutsch Ελληνικά

Drill bit Bohrer Λεπίδα τρυπανιού

Part of SDS-plus shank Teii des SDS-plus Schaftes Τμήμα του SDS-plus στελέχους

Front cap Vordere Abdeckung Μπροστινό περίβλημα

Grip Spannbacke Λαβή

Dust cup Staubschale Κύπελλο σκόνης

Dust collector (B) Staubfänger (B) Συλλέκτης σκόνης (Β)

Push button Druckschalter Κουμπί ώθησης

Change lever Wahlhebel Μοχλός αλλαγής

Push button Druckschalter Κουμπί ώθησης

Dust-collecting unit Staubfänger Μονάδα συλλογής σκόνης

Rail Strebe Οδηγός

Latch Verschluss Ασφάλεια

Nozzle Düse Ακροφύσιο

Adjuster Einstellvorrichtung Ρυθμιστής

Arrow Pfeil Βέλος

Adjuster rod Einstellstab Ράβδος ρυθμιστή

Lever Hebel Μοχλός

Dust box Staubgefäß Κουτί σκόνης

Nozzle seal Düsendichtung Εμφράκτης ακροστομίου

Rubber cap Gummikappe Ελαστικό κάλυμμα

Lip Lasche Χείλος

Groove Rille Εγκοπές

Groove between nozzle and nozzle

seal Rille zwischen Düse und Düsensitz Εγκοπές μεταξύ του ακροστομίου

και του εμφράκτη του ακροστομίου

Attachment hole Befestigungsloch Οπή προσαρμογής

Cover Abdeckung Κάλυμμα

Drill chuck Bohrfutter Σφικτήρας τρυπανιού

Chuck adapter Bohrfutteradapter Προσαρμογέας σφικτήρα

Chuck adapter (D) Bohrfutteradapter (D) Προσαρμογέας σφικτήρα (D)

Bit Bohrerspitze Λεπίδα

Socket Fassung Υποδοχή

Side handle Handgriﬀ Πλευρική λαβή

Stopper Anschlag Στόπερ

Mounting hole Befestigungsöﬀ nung Τρύπα στερέωσης

Wing bolt Flügelschraube Φτερωτό μπουλόνι

Tape shank adapter Kegelschaftadapter Κωνικός προσαρμογέας στελέχους

Cotter Dorn Κόφτης

Rest Auﬂ age Στήριγμα

Core bit Bohrkrone Κυλινδρικό κοπτικό τμήμα

Core bit shank Bohrkronenzapfen Άξονας κυλινδρικού κοπτικού

τμήματος

Thread Gewinde Σπείρωμα

Center pin Mittelstift Κεντρική περόνη

Guide plate Führungsplatte Οδηγητική πλάκα

Core bit tip Bohrkronenspitze Άκρη κυλινδρικού κοπτικού

τμήματος

Crank cover Kurbeldeckel Κάλυμμα στροφάλου

8

Polski Magyar Čeština

WiertłoFúróhegyVrták

Część chwytu SDS-plus Az SDS-plusz szár része Součást dříku SDS-plus

Przednia pokrywa Elülső kupak Přední kryt

Uchwyt Karmantyú Rukojeť

Kołnierz na pyłPorvédő sapka Prachová miska

Pojemnik na pył (B) Porgyűjtő (B) Lapač prachu (B)

Przycisk Nyomógomb Tlačítko

Dźwignia nastawcza Üzemmód váltó Přeřazovací páka

Przycisk Nyomógomb Tlačítko

Odpylacz Porgyűjtő egység Lapač prachu

Szyna Tartófém Vzpěra

Zatrzask Csappantyú Západka

Dysza Fúvóka Hubice

Regulator Szabályzó Nastavovací mechanizmus

Strzałka Nyíl Šipka

Pręt regulacji Beállító rúd Nastavovací tyč

Dźwignia Kar Páčka

Pojemnik na pyłPordoboz Prachový box

Uszczelka dyszy Fúvótömítés Těsnění trysky

Gumowa zatyczka Gumisapka Gumové víčko

Warga Perem Lem

Wyżłobienie Horony Žlábek

Wyżłobienie między dyszą a

uszczelką dyszy Horony a fúvó és a fúvótömítés között Žlábek mezi tryskou a těsněním

trysky

Otwór przyłączeniowy Csatlakozó nyílás Upevňovací otvor

Pokrywa Borító Kryt

Uchwyt wiertarski Fúrótokmány Sklíčidlo

Adaptor uchwytu Tokmány adapter Adaptér sklíčidla

Adaptor uchwytu narzędziowego (D) Tokmány adapter (D) Adaptér sklíčidla (D)

Wiertło Korona Nástroj

Gniazdo Befogópersely Objímka

Uchwyt boczny Oldalfogantyú Boční držadlo

Ogranicznik Rögzítőgomb Zarážka

Otwór mocujący Vezető lyuk Upevňovací otvor

Śruba łopatkowa Szárnyas csavar Křídlový šroub

Adaptor uchwytu stożkowego Kónuszos szár adapter Adaptér pro kuželovou stopku

SworzeńÉk Závlačka

Oparcie Alátámasztó blokk Klidová poloha

Koronka rdzeniowa Magfúró korona Okružní dutý vrták

Trzon koronki rdzeniowej Magfúró korona szára Stopka pro středový vrták

Gwint Menet Závit

Sworzeń centrujący Központosító tüske Středový vrtákbeton

Płyta wiodąca Vezetőlap Šablona

Granica zużycia Kopási határ Mez opotřebení

Pokrywa korby Hajtómű burkolata Kryt převodovky

9

Türkçe RomânăSlovenščina

Matkap ucu Burghiu Sveder

SDS-plus şank parçasıParte a trunchiului SDS- plus Del stebla SDS-plus

Ön mandren kapağıCapac frontal Sprednji pokrov

Kabza Cap de prindere Držalo

Tozluk Inel de colectare a prafului Lovilnik prahu

Toz toplayıcı (B) Colector de praf (B) Zbiralnik prahu (B)

Basma düğmesi Buton de comandăGumb

Değiştirme kolu Manetă de comutare Preklopna ročica

Basma düğmesi Buton de comandăGumb

Toz toplama ünitesi Unitate colectare praf Enota za prestrezanje prahu

Ray ŞinăVodilo

Kilit Dispozitiv de blocare Zapah

AğızAjutajŠoba

AyarlayıcıDispozitiv reglare Nastavljalo

Ok SăgeatăPuščica

Ayar çubuğuTijă reglare Drog za nastavljalo

Kol Pârghie Vzvod

Toz kutusu Cutie praf Škatla za prah

Meme contasıObturator Šobno tesnilo

Lastik kapak Manşon de protecţie Gumijasta kapa

Dudak Opritor Nastavek

Oluk Melc Utor

Meme ve meme contası arasındaki

oluk Melcul dintre duză şi obturator Utor med šobo in šobnim tesnilom

Bağlantı deliği Orificiu pentru ataşare Luknja za pritrditev

Kapak MascăPokrov

Ek Mandren MandrinăVrtalna glava

Mandren adaptörü Adaptor pentru mandrinăAdapter vrtalne glave

Mandren adaptörü (D) Adaptor pentru mandrină (D) Adapter vrtalne glave (D)

Uç Cap Nastavek

Soket Clichet Obojka

Yan kol Mâner lateral Stranski držaj

Durdurma düğmesi Opritor Zaustavljalo

Montaj deliğiGaură de prindere Pritrdilna odprtina

Kelebek başlı cıvata Bolţ fluture Krilat vijak

Konik sap adaptörü Adaptor pentru coadă conicăAdapter za konično steblo

Kama Dorn Trn

Destekler Suport Prislon

Buat ucu Burghiu găurire inelarăVrtalna krona

Buat ucu sapıPiesă antrenare burghiu Gred vrtalne glave

DişFilet Navoj

Merkez pimi Ştift centrare Centrirni zatič

Kılavuz plakasıPlacă ghidare Vodilna plošča

Yıpranma limiti Capăt burghiu găurire inelarăVrh vrtalne krone

Krank kapağıCapac în formă de cot Pokrov ročičnega mehanizma

10

Symbols

WARNING

The following show symbols

used for the machine. Be

sure that you understand

their meaning before use.

Symbole

WARNUNG

Die folgenden Symbole

werden für diese Maschine

verwendet. Achten Sie

darauf, diese vor der

Verwendung zu verstehen.

Σύμβολα

ΠΡΟΣΟΧΗ

Τα παρακάτω δείχνουν

τα σύμβολα που

χρησιμοποιούνται στο

μηχάνημα. Βεβαιωθείτε ότι

κατανοείτε τη σημασίας

τους πριν τη χρήση.

Symbole

OSTRZEŻENIE

Następujące oznaczenia

to symbole używane w

instrukcji obsługi maszyny.

Upewnij się, że rozumiesz

ich znaczenie zanim użyjesz

narzędzia.

Jelölések

FIGYELEM

Az alábbiakban a géphez

alkalmazott jelölések

vannak felsorolva. A gép

használata előtt feltétlenül

ismerje meg ezeket a

jelöléseket.

To reduce the risk of

injury, user must read

instruction manual.

Failure to follow the

warnings and instructions

may result in electric shock,

ﬁ re and/or serious injury.

Der Anwender muss die

Bedienungsanleitung

lesen, um das Risiko

einer Verletzung zu

verringern.

Wenn die Warnungen

und Anweisungen nicht

befolgt werden, kann es

zu Stromschlag, Brand

und/oder ernsthaften

Verletzungen kommen.

Για τον περιορισμό του

κινδύνου τραυματισμού,

ο χρήστης πρέπει να

διαβάσει το εγχειρίδιο

οδηγιών χρήσης.

Η μη τήρηση των

προειδοποιήσεων και

οδηγιών μπορεί να

προκαλέσει

ηλεκτροπληξία, πυρκαγιά

και/ή σοβαρό τραυματισμό.

Aby zmniejszyć ryzyko

odniesienia obrażeń,

użytkownik powinien

przeczytać instrukcję

obsługi.

Nieprzestrzeganie

ostrzeżeń oraz wskazówek

bezpieczeństwa może

spowodować porażenie

prądem elektrycznym,

pożar i/ lub odniesienie

poważnych obrażeń.

A sérülések

kockázatának

csökkentése érdekében,

a használónak el kell

olvasnia a használati

útmutatót.

A ﬁ gyelmeztetések

és utasítások be nem

tartása áramütést, tüzet

és/vagy súlyos sérülést

eredményezhet.

Only for EU countries

Do not dispose of electric

tools together with

household waste material!

In observance of European

Directive 2012/19/EU

on waste electrical and

electronic equipment

and its implementation in

accordance with national

law, electric tools that

have reached the end of

their life must be collected

separately and returned

to an environmentally

compatible recycling facility.

Nur für EU-Länder

Werfen Sie

Elektrowerkzeuge nicht in

den Hausmüll!

Gemäss Europäischer

Richtlinie 2012/19/EU über

Elektro- und Elektronik-

Altgeräte und Umsetzung

in nationales Recht

müssen verbrauchte

Elektrowerkzeuge

getrennt gesammelt und

einer umweltgerechten

Wiederververtung zugeführt

werden.

Μόνο για τις χώρες της EE

Μην πετάτε τα ηλεκτρικά

εργαλεία στον κάδο

οικιακών απορριμμάτων!

Σύμφωνα με την

εuρωπαϊκή οδηγία

2012/19/EE περί

ηλεκτρικών και

ηλεκτρονικών σuσκεuώv

και την ενσωμάτωσή

της στο εθνικό

δίκαιο, τα ηλεκτρικά

εργαλεία πρέπει να

σuλλέγovται ξεχωριστά

και να επιστρέφονται

για ανακύκλωση με

τρόπο φιλικό προς το

περιβάλλον.

Dotyczy tylko państw UE

Nie wyrzucaj

elektronarzędzi wraz z

odpadami z gospodarstwa

domowego!

Zgodnie z Europejską

Dyrektywą 2012/19/UE w

sprawie zużytego sprzętu

elektrotechnicznego i

elektronicznego oraz

dostosowaniem jej do

prawa krajowego, zużyte

elektronarzędzia należy

posegregować i zutylizować

w sposób przyjazny dla

środowiska.

Csak EU-országok számára

Az elektromos

kéziszerszámokat ne dobja

a háztartási szemétbe!

A használt villamos és

elektronikai készülékekről

szóló 2012/19/EU irányelv

és annak a nemzeti jogba

való átültetése szerint az

elhasznált elektromos

kéziszerszámokat

külön kell gyűjteni, és

környezetbarát módon újra

kell hasznosítani.

Symboly

UPOZORNĚNÍ

Následující text obsahuje

symboly, které jsou použity

na zařízení. Ujistěte se, že

rozumíte jejich obsahu před

tím, než začnete zařízení

používat.

Simgeler

DİKKAT

Aşağıda, bu alet için kullanılan

simgeler gösterilmiştir.

Aleti kullanmadan önce

bu simgelerin ne anlama

geldiğini anladığınızdan

emin olun.

Simboluri

AVERTISMENT

În cele ce urmează sunt

prezentate simbolurile

folosite pentru maşină.

Înainte de utilizare,

asiguraţi-vă că înţelegeţi

semniﬁ caţia acestora.

Simboli

OPOZORILO

V nadaljevanju so prikazani

simboli, uporabljeni pri

stroju. Pred uporabo se

prepričajte, da jih razumete.

Aby se snížilo riziko

zranění, uživatel si musí

přečíst návod k obsluze.

Nedodržení těchto varování

a pokynů může mít za

následek elektrický šok,

požár a/nebo vážné zranění.

Kullanıcı yaralanma

riskini azaltmak için

kullanım kılavuzunu

okumalıdır.

Uyarılara ve talimatlara

uyulmaması elektrik

çarpmasına, yangına ve/

veya ciddi yaralanmaya

neden olabilir.

Pentru a reduce

riscul de accidente,

utilizatorul trebuie să

citească manualul de

utilizare.

Nerespectarea

avertismentelor şi a

instrucţiunilor poate avea ca

efect producerea de şocuri

electrice, incendii şi/sau

vătămări grave.

Da ne bi prišlo do

poškodb, mora

uporabnik prebrati

navodila.

Z neupoštevanjem opozoril

in navodil tvegate električni

udar, požar in/ali resne

telesne poškodbe.

Jen pro státy EU

Elektrické nářadí

nevyhazujte do

komunálního odpadu!

Podle evropské směrnice

2012/19/EU o nakládání s

použitými elektrickými a

elektronickými zařízeními a

odpovídajících ustanovení

právních předpisů

jednotlivých zemí se

použitá elektrická nářadí

musí sbírat odděleně od

ostatního odpadu a podrobit

ekologicky šetrnému

recyklování.

Sadece AB ülkeleri için

Elektrikli el aletlerini evdeki

çöp kutusuna atmayınız!

Kullanılmış elektrikli

aletleri, elektrik ve

elektronikli eski cihazlar

hakkındaki 2012/19/AB

Avrupa yönergelerine göre

ve bu yönergeler ulusal

hukuk kurallarına göre

uyarlanarak, ayrı olarak

toplanmalı ve çevre

şartlarına uygun bir şekilde

tekrar değerlendirmeye

gönderilmelidir.

Numai pentru ţările membre

UE

Nu aruncaţi această sculă

electrică împreună cu

deşeurile menajere!

În conformitate cu Directiva

Europeană 2012/19/UE

referitoare la deşeurile

reprezentând echipamente

electrice şi electronice şi la

implementarea acesteia în

conformitate cu legislaţiile

naţionale, sculele electrice

care au ajuns la ﬁ nalul

duratei de folosire trebuie

colectate separat şi duse

la o unitate de reciclare

compatibilă cu mediul

înconjurător.

Samo za države EU

Električnih orodij ne zavržite

skupaj z gospodinjskimi

odpadki!

V skladu z evropsko

direktivo 2012/19/EU

o odpadni električni in

elektronski opremi in izvedbi

v skladu z državnimi zakoni,

je treba električna orodja, ki

so dosegla življenjsko dobo

ločeno zbirati in vrniti v z

okoljem združljivo ustanovo

za recikliranje.

English

11

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and

speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁ ed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk of

electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-skid

safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting to

power source and/or battery pack, picking up or

carrying the tool.

Carrying power tools with your ﬁ nger on the switch or

energising power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of the

power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts.

Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and safer

at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power toolʼs operation. If

damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

(Original instructions)

English

12

ROTARY HAMMER SAFETY WARNINGS

Safety instructions for all operations

1. Wear ear protectors

Exposure to noise can cause hearing loss.

2. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

3. Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

Safety instructions when using long drill bits with

rotary hammers

4. Always start drilling at low speed and with the bit tip

in contact with the workpiece.

At higher speeds, the bit is likely to bend if allowed to

rotate freely without contacting the workpiece, resulting

in personal injury.

5. Apply pressure only in direct line with the bit and do

not apply excessive pressure.

Bits can bend causing breakage or loss of control,

resulting in personal injury.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions and

the work to be performed.

Use of the power tool for operations diﬀ erent from

those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease.

Slippery handles and grasping surfaces do not allow

for safe handling and control of the tool in unexpected

situations.

5) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool is

maintained.

PRECAUTION

Keep children and inﬁ rm persons away.

When not in use, tools should be stored out of reach of

children and inﬁ rm persons.

SPECIFICATIONS

Voltage (by areas)* (110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)

Power Input 720 W

No-load speed 0–1050 min–1

Full-load impact rate 0–4000 min–1

Capacity: concrete

steel

wood

4–28 mm

13 mm

32 mm

Weight** 4.1 kg

Dust collecting adapter

Max. hole-drilling depth:

Diameter of drill:

Max. length of drill (eﬀ ective length):

85 mm (adjustment possible between 0 and 85 mm)

4–18 mm

100 mm

Dust box capacity: 0.4 liters

* Be sure to check the nameplate on product as it is subject to change by areas.

** According to EPTA-Procedure 01/2014.

STANDARD ACCESSORIES

(1) Plastic case ..................................................................1

(2) Side handle ..................................................................1

(3) Stopper ........................................................................1

(4) Cover ...........................................................................1

(5) Rubber cap (replacement) ...........................................1

Standard accessories are subject to change without notice.

English

13

OPTIONAL ACCESSORIES (sold separately)

+

+ +

Drill bit (Taper shank)

Taper shank

adapter Cotter

Guide plate Center pin Core bit Core bit shank

● Large hole boring

● Anchor setting

Anchor setting adapter

● Bolt placing operation with

Chemical Anchor

Chemical anchor adapter

Chuck

adapter

Drill chuck

(13 VLRB-D)

Special

screw

● Demolishing operation

Dust cup Dust collector (B)

Rotation only Hammering only Rotation + Hammering

●

Drilling holes in concrete or tile

● Drilling anchor holes

● Groove digging and edging

● Grooving

● Driving screws

● Drilling in steel or wood

⊕ Driver bit ⊖ Driver bit

Drill bit for steel Drill bit for wood

Grooving chisel

Cold chisel Cutter

Hexagon socket

Bull point

(Square type) Bull point

(Round type)

Drill bit

Tool Adapters

Use on jobs facing upwards

English

14

● Drilling holes in concrete or tile

SDS-plus Drill bit

Outer dia. Overall length Eﬀ ective length

4.0 mm 110 mm 50 mm

5.0 mm 110 mm 50 mm

160 mm 100 mm

5.5 mm 110 mm 50 mm

6.5 mm 160 mm 100 mm

7.0 mm 160 mm 100 mm

8.0 mm 160 mm 100 mm

8.5 mm 160 mm 100 mm

9.0 mm 160 mm 100 mm

12.0 mm 166 mm 100 mm

260 mm 200 mm

12.7 mm 166 mm 100 mm

14.0 mm 166 mm 100 mm

15.0 mm 166 mm 100 mm

16.0 mm 166 mm 100 mm

260 mm 200 mm

17.0 mm 166 mm 100 mm

19.0 mm 260 mm 200 mm

20.0 mm 250 mm 200 mm

22.0 mm 250 mm 200 mm

25.0 mm 450 mm 400 mm

● Drilling anchor holes

Taper shank adapter

Taper mode

Morse taper No.1

Morse taper No.2

A-Taper

B-taper

● Large hole boring

Core bit

Outer dia. Center pin Core bit shank

Overall length

25 mm* Not applicable

105 mm

300 mm

29 mm*

32 mm

(A)35 mm

38 mm

45 mm

(B) 300 mm

50 mm

65 mm

80 mm

* Without guide plate

● Anchor setting

Anchor setting adapter

Anchor size

W 1/4”

W 5/16”

W 3/8”

W 1/2”

W 5/8”

Optional accessories are subject to change without notice.

APPLICATIONS

Rotation and hammering function

○ Drilling anchor holes

○ Drilling holes in concrete

○ Drilling holes in tile

Rotation only function

○ Drilling in steel or wood

(with optional accessories)

○ Tightening machine screws, wood screws

(with optional accessories)

Hammering only function

○ Light-duty chiselling of concrete, groove digging and

edging.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms

to the power requirements speciﬁ ed on the product

nameplate.

2. Power switch

Ensure that the power switch is in the OFF position. If

the plug is connected to a power receptacle while the

power switch is in the ON position, the power tool will

start operating immediately, which could cause a serious

accident.

3. Extension cord

When the work area is removed from the power source,

use an extension cord of suﬃ cient thickness and rated

capacity. The extension cord should be kept as short as

practicable.

4. Mounting the drill bit (Fig. 1)

CAUTION

To prevent accidents, make sure to turn the switch oﬀ

and disconnect the plug from the receptacle.

NOTE

When using tools such as bull points, drill bits, etc.,

make sure to use the genuine parts designated by our

company.

(1) Clean the shank portion of the drill bit.

(2) Insert the drill bit in a twisting manner into the tool holder

until it latches itself. (Fig. 1)

(3) Check the latching by pulling on the drill bit.

(4) To remove the drill bit, fully pull the grip in the direction of

the arrow and pull out the drill bit. (Fig. 2)

5. Installation of dust cup or dust collector (B)

(Optional accessories) (Fig. 3, Fig. 4)

When using a rotary hammer for upward drilling

operations attach a dust cup or dust collector (B) to

collect dust or particles for easy operation.

English

15

○ Installing the dust cup

Use the dust cup by attaching to the drill bit as shown in

Fig. 3.

When using a bit which has big diameter, enlarge the

center hole of the dust cup with this rotary hammer.

○ Installing dust collector (B)

When using dust collector (B), insert dust collector (B)

from the tip of the bit by aligning it to the groove on the

grip. (Fig. 4)

CAUTION

○ The dust cup and dust collector (B) are for exclusive use

of concrete drilling work. Do not use them for wood or

metal drilling work.

○ Insert dust collector (B) completely into the chuck part of

the main unit.

○ When turning the rotary hammer on while dust collector

(B) is detached from a concrete surface, dust collector

(B) will rotate together with the drill bit. Make sure to turn

on the switch after pressing the dust cup on the concrete

surface. (When using dust collector (B) attached to

a drill bit that has more than 190 mm of overall length,

dust collector (B) cannot touch the concrete surface and

will rotate. Therefore please use dust collector (B) by

attaching to drill bits which have 166 mm, 160 mm, and

110 mm overall length.)

○ Dump particles after every two or three holes when

drilling.

○ Please replace the drill bit after removing dust collector

(B).

6. Selecting the driver bit

Screw heads or bits will be damaged unless a bit

appropriate for the screw diameter is employed to drive

in the screws.

7. Conﬁ rm the direction of bit rotation (Fig. 5)

The bit rotates clockwise (viewed from the rear side) by

pushing the R-side of the push button. The L-side of the

push button is pushed to turn the bit counterclockwise.

8. Selecting the function mode

You can switch functions to the 3 modes of “hammering

only”, “rotation + hammering”, and “rotation only” by

turning the change lever while pressing the push button.

Set the ▲ mark position of the change lever to that of the

mode to be used.

CAUTION

○ Before operating the change lever, check and make sure

that the motor has stopped.

A failure can occur if it is operated while the motor is

running.

○ To operate the change lever, press the push button,

and release the lock of the change lever. Also, check

and make sure after operation that the push button has

returned and that the change lever has been locked.

○ Switch the change lever without mistake. If it is used at a

position halfway, there is a fear that the service life of the

switching mechanism may be shortened.

HOW TO USE

CAUTION

To prevent accidents, make sure to turn the switch oﬀ

and disconnect the plug from the receptacle when the

drill pits and other various parts are installed or removed.

The power switch should also be turned oﬀ during a work

break and after work.

NOTE

Ensure that the wing bolt in the side handle is properly

tightened before using the tool.

1. Switch operation

The rotation speed of the drill bit can be controlled

steplessly by varying the amount that the trigger switch

is pulled. Speed is low when the trigger switch is pulled

slightly and increases as the switch is pulled more.

However, the switch trigger can only be pulled in halfway

during reverse and rotates at half the speed of forward

operation.

2. Rotation + hammering

This rotary hammer can be set to rotation and hammering

mode by pressing the push button and turning the change

lever to the mark. (Fig. 6)

Turn the grip slightly and conﬁ rm that the clutch has been

engaged with a click.

(1) Mount the drill bit.

(2) Pull the trigger switch after applying the drill bit tip to the

drilling position. (Fig. 7)

(3) Pushing the rotary hammer forcibly is not necessary at

all. Pushing slightly so that drill dust comes out gradually

is suﬃ cient.

CAUTION

When the drill bit touches construction iron bar, the bit

will stop immediately and the rotary hammer will react to

revolve. Therefore grip the side handle and handle tightly

as shown in Fig. 7.

3. Using the dust-collecting unit

Using the rotary hammer with the dust-collecting unit

attached creates a more hygienic working environment

free of ﬂ ying dust (Fig. 8).

(1) Attaching the dust-collecting unit

Insert the dust-collecting unit along the rail on the rotary

hammer. When it is inserted as far as it will go, ﬁ x it to the

rotary hammer with the two latches (Fig. 9).

CAUTION

The dust-collecting unit is designed for use when drilling

concrete. Do not use for drilling holes in metal or wood.

(2) Adjusting the dust-collecting unit

(a) Adjusting the position of the dust-collecting nozzle

Push the nozzle in and adjust to the desired position.

Pull the adjuster on the nozzle in the direction of the

arrow to release the lock and move until it contacts

with the adjuster rod. Push the adjuster in the

opposite direction to the arrow to lock (Fig. 10).

(b) Setting the hole-drilling depth

Pull the adjuster on the handle in the direction of the

arrow to release the lock, move to the desired position

to determine the stroke, and push the adjuster in the

opposite direction to the arrow to lock.

The nozzle travel distance when the tip of the nozzle

matches the tip of the drill bit is the hole-drilling depth.

(Fig. 11)

○ The maximum hole-drilling depth when using the

dust-collecting unit is 85 mm.

○ When using the dust-collecting unit, it is possible to

use HiKOKI drill bits between 4 mm and 18 mm in

diameter and up to 100 mm in eﬀ ective length.

(3) Drilling holes

When drilling holes, hold the rotary hammer so that the

tip of the nozzle contacts with the concrete surface. Dust-

collecting eﬀ ectiveness is reduced if the unit is not in

contact with the surface (Fig. 12).

English

16

(4) Removing dust

Excessive dust in the dust box will reduce dust-collecting

eﬀ ectiveness. Empty the dust box regularly.

Push the lever to remove the dust box from the dust-

collecting unit, and empty and clean the box (Fig. 13).

Dust-collecting eﬀ ectiveness is reduced if the ﬁ lter in the

dust box becomes blocked.

Use the table below as a guide to replacement of the dust

box.

Dust box capacity Drill diameter of 6 mm / depth of 28 mm: 130 holes

Drill diameter of 8 mm / depth of 30 mm: 75 holes

Drill diameter of 12 mm / depth of 50 mm: 20 holes

Guide to replacement of dust box Dust box has been ﬁ lled and emptied 100 times

(5) Replacing the rubber cap

Wear of the rubber cap will reduce dust-collecting

eﬀ ectiveness.

Replace the rubber cap when it becomes worn.

How to replace the rubber cap (Fig. 14)

(1) Remove the nozzle seal from the nozzle.

(2) Replace the rubber cap with a new cap.

Fit the rubber cap making sure that it is correctly oriented.

(3) Attach the nozzle seal.

Insert the lip of the nozzle seal securely into the groove of

the nozzle.

At this time, make sure that the groove between the

nozzle and the nozzle seal is uniform all the way round.

4. When not using the dust-collecting unit

When using the rotary hammer without the dust-collecting

unit, attach the provided cover in the unit attachment hole

(Fig. 15).

CAUTION

If no cover is attached, dust or other particles may be

sucked up from the hole, causing damage to the motor.

5. Rotation only

NOTE

The dust-collecting unit cannot be used. Remove the unit

and attach the provided cover in the unit attachment hole.

CAUTION

If no cover is attached, dust or other particles may be

sucked up from the hole, causing damage to the motor.

This rotary hammer can be set to rotation only mode by

pressing the push button and turning the change lever to

the mark. (Fig. 16)

Turn the grip slightly and conﬁ rm that the clutch has been

engaged with a click.

To drill wood or metal material using the drill chuck

and chuck adapter (optional accessories), proceed as

follows.

Installing drill chuck and chuck adapter: (Fig. 17)

(1) Attach the drill chuck to the chuck adapter.

(2) The part of the SDS-plus shank is the same as the drill

bit. Therefore, refer to the item of “Mounting the drill bit”

for attaching it.

CAUTION

○ Application of force more than necessary will not only

expedite the work, but will deteriorate the tip edge of the

drill bit and reduce the service life of the rotary hammer in

addition.

○ Drill bits may snap oﬀ while withdrawing the rotary

hammer from the drilled hole. For withdrawing, it is

important to use a pushing motion.

○ Do not attempt to drill anchor holes or holes in concrete

with the machine set in the rotation only function.

○ Do not attempt to use the rotary hammer in the rotation

and hammering function with the drill chuck and chuck

adapter attached. This would seriously shorten the

service life of every component of the machine.

6. When driving machine screws (Fig. 18)

First, insert the bit into the socket in the end of chuck

adapter (D).

Next, mount chuck adapter (D) on the main unit using

procedures described in 4 (1), (2), (3), put the tip of the

bit in the slots in the head of the screw, grasp the main

unit and tighten the screw.

CAUTION

○ Exercise care not to excessively prolong driving time,

otherwise, the screws may be damaged by excessive

force.

○ Apply the rotary hammer perpendicularly to the screw

head when driving the screw; otherwise, the screw head

or bit will be damaged, or driving force will not be fully

transferred to the screw.

○ Do not attempt to use the rotary hammer in the rotation

and hammering function with the chuck adapter and bit

attached.

7. When driving wood screws (Fig. 18)

(1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver bit

easily slips oﬀ the heads of minus-head screws.

(2) Driving in wood screws

○ Prior to driving in wood screws, make pilot holes suitable

for them in the wooden board. Apply the bit to the screw

head grooves and gently drive the screws into the holes.

○ After rotating the rotary hammer at low speed for a while

until the wood screw is partly driven into the wood,

squeeze the trigger more strongly to obtain the optimum

driving force.

CAUTION

Exercise care in preparing a pilot hole suitable for

the wood screw taking the hardness of the wood into

consideration. Should the hole be excessively small or

shallow, requiring much power to drive the screw into

it, the thread of the wood screw may sometimes be

damaged.

8. Hammering only

NOTE

The dust-collecting unit cannot be used. Remove the unit

and attach the provided cover in the unit attachment hole.

CAUTION

If no cover is attached, dust or other particles may be

sucked up from the hole, causing damage to the motor.

This rotary hammer can be set to hammering only mode

by pressing the push button and turning the change lever

to the mark (Fig. 19).

English

17

(1) Mount the bull point or cold chisel.

(2) Press the push button and set the change lever to

mark. (Fig. 20)

The rotation is released, turn the tool and adjust the tool

to desired position. (Fig. 21)

(3) Turn the change lever to mark. (Fig. 19)

Then bull point or cold chisel is locked.

9. Using the stopper (Fig. 22)

(1) Loosen the wing bolt and insert the stopper into the

mounting hole on the side handle.

(2) Adjust the stopper position according to the depth of the

hole and tighten the wing bolt securely.

10. How to use the drill bit (taper shank) and the taper

shank adapter

(1) Mount the taper shank adapter to the rotary hammer.

(Fig. 23)

(2) Mount the drill bit (taper shank) to the taper shank

adapter. (Fig. 23)

(3) Turn the switch ON, and drill a hole in prescribed depth.

(4) To remove the drill bit (taper shank), insert the cotter into

the slot of the taper shank adapter and strike the head of

the cotter with a hammer supporting on a rests. (Fig. 24)

11. Make sure to securely hold the tool as shown in

Fig. 31 during operation.

12. Using the side handle

When you wish to change a position of the side handle,

turn grip of the side handle counterclockwise to loosen it,

and then fasten it ﬁ rmly. (Fig. 32)

CAUTION

When boring a hole, there can be a case where the

machine attempts to rotate by the reaction at the time of

penetrating a concrete wall and/or when a tip of the blade

comes in contact with the rebar.

Firmly fasten the side handle and hold the machine

with both of your hands. Unless you hold it securely, an

accident can occur.

HOW TO USE THE CORE BIT

(FOR LIGHT LOAD)

When boring penerating large holes use the core bit (for light

loads). At that time use with the center pin and the core bit

shank provided as optional accessories.

1. Mounting

CAUTION

Be sure to turn power OFF and disconnect the plug from

the receptacle.

(1) Mount the core bit to the core bit shank (Fig. 25).

Lubricate the thread of the core bit shank to facilitate

disassembly.

(2) Mount the core bit to the rotary hammer (Fig. 26).

(3) Insert the center pin into the guide plate until it stops.

(4) Engage the guide plate with the core bit, and turn the

guide plate to the left or the right so that it does not fall

even if it faces downward (Fig. 27).

2. How to bore (Fig. 28)

(1) Connect the plug to the power source.

(2) A spring is installed in the center pin.

Push it lightly to the wall or the ﬂ oor straight.

Connect the core bit tip ﬂ ush to the surface and start

operating.

(3) When boring about 5 mm in depth the position of the hole

will be established. Bore after that removing the center

pin and the guide plate from core bit.

(4) Application of excessive force will not only expedite

the work, but will deteriorate the tip edge of the drill bit,

resulting in reduced service life of the rotary hammer.

CAUTION

When removing the center pin and the guide plate,

turn OFF the switch and disconnect the plug from the

receptacle.

3. Dismounting (Fig. 29)

Remove the core bit shank from the rotary hammer and

strike the head of the core bit shank strongly two or three

times with a hammer holding the core bit, then the thread

becomes loose and the core bit can be removed.

GREASE REPLACEMENT

This Rotary Hammer is of full air-tight construction to protect

against dust. This machine can be used without grease

replenishment for an extended period of time. However,

perform the grease replacement to extend the service life.

Replace the grease as described below.

1. Grease Replacement Period

You should look at the grease when you change the

carbon brush. (See item 4 in the section MAINTENANCE

AND INSPECTION.)

Ask for grease replacement at the nearest authorized

HiKOKI Service Center.

In the case that you are forced to change the grease by

yourself, please follow the following points.

2. How to replace grease

CAUTION

Before replacing the grease, turn the power oﬀ and pull

out the plug from the receptacle.

(1) Disassemble the crank cover and thoroughly wipe oﬀ the

old grease inside. (Fig. 30)

(2) Supply 25 g of HiKOKI Electric Hammer Grease A

(standard accessory, contained in tube) in the crank

case.

(3) After replacing the grease, reassemble the crank cover

securely. At this time, do not damage or lose the oil seal.

NOTE

The HiKOKI Electric Hammer Grease A is of the

low viscosity type. When the grease is consumed,

purchase from the authorized HiKOKI Service

Center.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

Since use of a dull tool will cause motor malfunctioning

and degraded eﬃ ciency, replace the drill bit with new

ones or resharpen them without delay when abrasion is

noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very ”heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock protection,

carbon brush inspection and replacement on this tool

should ONLY be performed by a HiKOKI Authorized

Service Center.

English

18

5. Replacing supply cord

If the replacement of the supply cord is necessary, it has

to be done by HiKOKI Authorized Service Center to avoid

a safety hazard.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country speciﬁ c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or normal

wear and tear. In case of complaint, please send the Power

Tool, undismantled, with the GUARANTEE CERTIFICATE

found at the end of this Handling instruction, to a HiKOKI

Authorized Service Center.

NOTE

Due to HiKOKI’s continuing program of research and

development, the speciﬁ cations herein are subject to change

without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to

EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 102 dB (A).

Measured A-weighted sound pressure level: 91 dB (A).

Uncertainty KpA: 3 dB (A).

Wear ear protection.

Vibration total values (triax vector sum) determined

according to EN62841.

Hammer drilling into concrete:

Vibration emission value ah, HD = 15.9 m/s2

Uncertainty K = 2.5 m/s2 (A)

Equivalent chiselling value:

Vibration emission value ah, CHeq = 14.3 m/s2

Uncertainty K = 2.0 m/s2 (A)

The declared vibration total value and the declared noise

emission value have been measured in accordance with a

standard test method and may be used for comparing one

tool with another.

They may also be used in a preliminary assessment of

exposure.

WARNING

○ The vibration and noise emission during actual use

of the power tool can diﬀ er from the declared total

value depending on the ways in which the tool is used

especially what kind of workpiece is processed; and

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched oﬀ and when it is running idle in addition to the

trigger time).

Deutsch

19

ALLGEMEINE SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Bitte beachten Sie sämtliche mit diesem Elektrogerät

gelieferten Sicherheitshinweise, Anweisungen,

Illustrationen und technischen Angaben.

Wenn die nachfolgenden Anweisungen nicht befolgt werden,

kann es zu Stromschlag, Brand und/oder ernsthaften

Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und Anweisungen

zum späteren Nachschlagen auf.

Der Begriﬀ „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

1) Sicherheit im Arbeitsbereich

a) Sorgen Sie für einen sauberen und gut

ausgeleuchteten Arbeitsbereich.

Zugestellte oder dunkle Bereiche ziehen Unfälle

förmlich an.

b) Verwenden Sie Elektrowerkzeuge niemals an

Orten, an denen Explosionsgefahr besteht,

wie zum Beispiel in der Nähe von leicht

entﬂ ammbaren Flüssigkeiten, Gasen oder

Stäuben.

Bei der Arbeit mit Elektrowerkzeugen kann es zu

Funkenbildung kommen, wodurch sich Stäube oder

Dämpfe entzünden können.

c) Sorgen Sie bei der Arbeit mit Elektrowerkzeugen

dafür, dass sich keine Zuschauer (insbesondere

Kinder) in der Nähe beﬁ nden.

Wenn Sie abgelenkt werden, können Sie die

Kontrolle über das Werkzeug verlieren.

2) Elektrische Sicherheit

a) Elektrowerkzeuge müssen mit passender

Stromversorgung betrieben werden. Nehmen

Sie niemals irgendwelche Änderungen am

Anschlussstecker vor. Verwenden Sie bei

Elektrowerkzeugen mit Schutzkontakt (geerdet)

niemals Adapterstecker.

Stecker im Originalzustand und passende

Steckdosen reduzieren das Stromschlagrisiko.

b) Vermeiden Sie Körperkontakt mit geerdeten

Gegenständen wie Rohrleitungen, Heizungen,

Herden oder Kühlschränken.

Bei Körperkontakt mit geerdeten Gegenständen

besteht ein erhöhtes Stromschlagrisiko.

c) Setzen Sie Elektrowerkzeuge niemals Regen

oder sonstiger Feuchtigkeit aus.

Wenn Flüssigkeiten in ein Elektrowerkzeug

eindringen, erhöht sich das Stromschlagrisiko.

d) Verwenden Sie das Anschlusskabel nicht

missbräuchlich. Tragen Sie das Elektrowerkzeug

niemals am Stromkabel, ziehen Sie es nicht

damit heran und ziehen Sie den Stecker nicht

am Anschlusskabel aus der Steckdose.

Halten Sie das Anschlusskabel von Hitzequellen,

Öl, scharfen Kanten und beweglichen Teilen

fern.

Beschädigte oder verdrehte Anschlusskabel erhöhen

das Stromschlagrisiko.

e) Verwenden Sie, wenn Sie ein Elektrowerkzeug

im Freien benutzen, ein für den Außeneinsatz

geeignetes Verlängerungskabel.

Ein für den Außeneinsatz geeignetes Kabel

vermindert das Stromschlagrisiko.

f) Falls sich der Betrieb des Elektrowerkzeugs

in feuchter Umgebung nicht vermeiden lässt,

verwenden Sie eine Stromversorgung mit

Fehlerstromschutzeinrichtung (Residual

Current Device, RCD).

Durch den Einsatz einer Fehlerstromschutzeinrichtung

wird das Risiko eines elektrischen Schlages

reduziert.

3) Persönliche Sicherheit

a) Bleiben Sie wachsam, achten Sie auf das, was

Sie tun, und setzen Sie Ihren Verstand ein, wenn

Sie mit Elektrowerkzeugen arbeiten.

Benutzen Sie keine Elektrowerkzeuge, wenn

Sie müde sind oder unter Einﬂ uss von Drogen,

Alkohol oder Medikamenten stehen.

Bei der Arbeit mit Elektrowerkzeugen können bereits

kurze Phasen der Unaufmerksamkeit zu schweren

Verletzungen führen.

b) Benutzen Sie eine persönliche

Schutzausrüstung. Tragen Sie immer einen

Augenschutz.

Schutzausrüstung wie Staubmaske, rutschfeste

Sicherheitsschuhe, Schutzhelm und Gehörschutz

senken bei angemessenem Einsatz das

Verletzungsrisiko.

c) Vermeiden Sie unbeabsichtigtes Einschalten.

Achten Sie darauf, dass sich der Schalter

in der Aus- (Oﬀ -) Position beﬁ ndet, ehe Sie

das Gerät mit der Stromversorgung und/

oder Batteriestromversorgung verbinden, es

aufheben oder herumtragen.

Das Herumtragen von Elektrowerkzeugen mit

dem Finger am Schalter oder das Herstellen der

Stromversorgung bei betätigtem Schalter zieht

Unfälle regelrecht an.

d) Entfernen Sie sämtliche Einstellwerkzeuge

(Einstellschlüssel), ehe Sie das Elektrowerkzeug

einschalten.

Ein an einem beweglichen Teil des Elektrowerkzeugs

angebrachter Schlüssel kann zu Verletzungen

führen.

e) Überstrecken Sie sich nicht. Achten Sie jederzeit

darauf, sicher zu stehen und das Gleichgewicht

zu bewahren.

Dadurch haben Sie das Elektrowerkzeug in

unerwarteten Situationen besser im Griﬀ .

f) Tragen Sie geeignete Kleidung. Tragen Sie keine

lose Kleidung oder Schmuck. Halten Sie Ihr Haar

und Ihre Kleidung von beweglichen Teilen fern.

Lose Kleidung, Schmuck oder langes Haar kann von

beweglichen Teilen erfasst werden.

g) Wenn Anschlüsse für Staubabsaug- und -

sammelvorrichtungen vorhanden sind, sorgen

Sie dafür, dass diese richtig angeschlossen und

eingesetzt werden.

Durch Entfernen des Staubes können staubbezogene

Gefahren vermindert werden.

(Übersetzung der Original-Gebrauchsanweisung)

Deutsch

20

h) Lassen Sie es nicht zu, dass die durch häuﬁ gen

Gebrauch von Werkzeugen erworbene

Vertrautheit Sie nachlässig macht und Sie

die Sicherheitsrichtlinien für das Werkzeug

ignorieren.

Eine unvorsichtige Handlung kann in

Sekundenbruchteilen zu schweren Verletzungen

führen.

4) Einsatz und Pﬂ ege von Elektrowerkzeugen

a) Überbeanspruchen Sie Elektrowerkzeuge nicht.

Benutzen Sie das richtige Elektrowerkzeug für

Ihren Einsatzzweck.

Das richtige Elektrowerkzeug erledigt seine Arbeit bei

bestimmungsgemäßem Einsatz besser und sicherer.

b) Benutzen Sie das Elektrowerkzeug nicht, wenn

es sich nicht am Schalter ein- und ausschalten

lässt.

Jedes Elektrowerkzeug, das nicht mit dem Schalter

betätigt werden kann, stellt eine Gefahr dar und muss

repariert werden.

c) Ziehen Sie den Stecker der Stromversorgung

ab und/oder entfernen Sie den Akkupack

vom Elektrowerkzeug, falls abnehmbar, ehe

Sie Einstellarbeiten vornehmen, Zubehörteile

tauschen oder das Elektrowerkzeug verstauen.

Solche präventiven Sicherheitsmaßnahmen

verhindern den unbeabsichtigten Anlauf des

Elektrowerkzeugs und die damit verbundenen

Gefahren.

d) Lagern Sie nicht benutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern, lassen

Sie nicht zu, dass Personen das Elektrowerkzeug

bedienen, die nicht mit dem Werkzeug selbst

und/oder diesen Anweisungen vertraut sind.

Elektrowerkzeuge in ungeschulten Händen sind

gefährlich.

e) Wartung von Elektrowerkzeugen und Zubehör.

Prüfen Sie sie auf Fehlausrichtungen,

Leichtgängigkeit beweglicher Teile,

Beschädigungen von Teilen und auf alle

anderen Umstände, die sich auf den Betrieb des

Elektrowerkzeugs auswirken können. Lassen

Sie das Elektrowerkzeug bei Beschädigungen

reparieren, ehe Sie es benutzen.

Viele Unfälle mit Elektrowerkzeugen sind auf

schlechte Wartung zurückzuführen.

f) Halten Sie Schneidwerkzeuge scharf und

sauber.

Richtig gewartete Schneidwerkzeuge mit scharfen

Schneiden bleiben weniger häuﬁ g hängen und sind

einfacher zu beherrschen.

g) Benutzen Sie Elektrowerkzeuge, Zubehör,

Werkzeugspitzen und Ähnliches in

Übereinstimmung mit diesen Anweisungen

– beachten Sie dabei die jeweiligen

Arbeitsbedingungen und die Art der

auszuführenden Arbeiten.

Der Gebrauch des Elektrowerkzeugs für andere

als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

h) Halten Sie Handgriﬀ e und Greiﬄ ächen trocken,

sauber und frei von Öl und Fett.

Rutschige Handgriﬀ e und Greiﬄ ächen lassen keine

sichere Handhabung und Kontrolle des Werkzeugs

in unerwarteten Situationen zu.

5) Service

a) Lassen Sie Elektrowerkzeuge durch qualiﬁ zierte

Fachkräfte und nur unter Einsatz passender

Originalersatzteile warten.

Dies sorgt dafür, dass die Sicherheit des

Elektrowerkzeugs nicht beeinträchtigt wird.

VORSICHT

Von Kindern und gebrechlichen Personen fernhalten.

Werkzeuge sollten bei Nichtgebrauch außerhalb der

Reichweite von Kindern und gebrechlichen Personen

aufbewahrt werden.

SICHERHEITSHINWEISE FÜR DEN

BOHRHAMMER

Allgemeine Sicherheitshinweise

1. Gehörschutz tragen

Die Aussetzung zu lauten Geräuschen kann zu

Gehörverlust führen.

2. Benutzen Sie, falls mit dem Werkzeug mitgeliefert,

den/die Hilfsgriﬀ (e).

Ein Verlust der Kontrolle kann zu Körperverletzungen

führen.

3. Halten Sie das Elektrowerkzeug bei Arbeiten,

bei denen das Schneidezubehör verborgene

Stromleitungen berühren könnte, nur an den

isolierten Griﬀ -Flächen.

Schneidezubehör, das eine Strom führende Leitung

berührt, kann nackte Metallteile des Elektrogeräts unter

Strom setzen und dem Bediener einen Stromschlag

versetzen.

Sicherheitshinweise zur Verwendung langer

Bohraufsätze mit Bohrhammern

4. Beginnen Sie beim Bohren immer mit niedriger

Drehzahl und so, dass die Spitze des Bits das

Werkstück berührt.

Bei höheren Drehzahlen kann sich das Bit verbiegen,

wenn es sich frei und ohne Kontakt mit dem Werkstück

dreht, was zu einer Verletzung führen kann.

5. Üben Sie Druck nur gerade entlang des Bits aus und

vermeiden Sie übermäßigen Druck.

Die Bits könnten sich verbiegen und brechen oder zu

Kontrollverlust und Verletzungen führen.

Strona jest ładowana ...

Hikoki DH28PD Instrukcja obsługi

Hikoki DH28PD Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty