LD Systems AMP 106 T Instrukcja obsługi

USER´S MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´UTILISATION

MANUAL DE USUARIO

INSTRUKCJA OBSŁUGI

MANUALE D´USO

AMP 106 T

1-CHANNEL MINI INSTALLATION POWER AMPLIFIER 60 W @ 4 OHM / 70V / 100V

LDAMP106T

CONTENTS / INHALTSVERZEICHNIS / CONTENU / CONTENIDO / TREŚĆ / CONTENUTO

ENGLISH

ABOUT THIS MANUAL 3

INTENDED USE 3

EXPLANATIONS OF TERMS AND SYMBOLS 3

SAFETY INSTRUCTIONS 4

PACKAGING CONTENT 7

INTRODUCTION 7

CONNECTIONS, OPERATING AND

DISPLAY ELEMENTS 8

TERMINAL BLOCK CONNECTIONS 10

CONNECTION EXAMPLE 11

UNDER / ON-TABLE MOUNTING 12

CARE, MAINTENANCE AND REPAIR 13

DIMENSIONS 14

TECHNICAL DATA 14

DISPOSAL 16

MANUFACTURER´S DECLARATIONS 17

DEUTSCH

INFORMATIONEN ZU DIESER

BEDIENUNGSANLEITUNG 18

BESTIMMUNGSGEMÄSSER GEBRAUCH 18

BEGRIFFS- UND SYMBOLERKLÄRUNGEN 18

SICHERHEITSHINWEISE 19

LIEFERUMFANG 22

EINLEITUNG 22

ANSCHLÜSSE, BEDIENUNG UND

ANZEIGEELEMENTE 23

KLEMMLEISTENANSCHLÜSSE 25

ANSCHLUSSBEISPIEL 26

UNTER- / AUFTISCHMONTAGE 27

PFLEGE, WARTUNG UND REPARATUR 28

ABMESSUNGEN 29

TECHNISCHE DATEN 29

ENTSORGUNG 31

HERSTELLERERKLÄRUNGEN 32

FRANCAIS

INFORMATIONS SUR CE MODE D‘EMPLOI 33

UTILISATION RÉGLEMENTÉE 33

EXPLICATIONS DES TERMES ET DES SYMBOLES 33

CONSIGNES DE SÉCURITÉ 34

CONTENU DE L‘EMBALLAGE 37

INTRODUCTION 38

BRANCHEMENTS, UTILISATION ET INDICATEURS 39

CONNEXIONS EUROBLOCK (BORNIER) 41

EXEMPLE DE CONNEXION 42

MONTAGE SOUS / SUR TABLE 43

ENTRETIEN, MAINTENANCE ET RÉPARATIONS 44

DIMENSIONS 45

CARACTÉRISTIQUES TECHNIQUES 46

MISE EN DÉCHETTERIE 48

DÉCLARATIONS DU FABRICANT 49

ESPAÑOL

INFORMACIÓN SOBRE ESTAS

INSTRUCCIONES DE USO 50

USO CONFORME A LA NORMATIVA 50

EXPLICACIONES DE TÉRMINOS Y SíMBOLOS 50

INSTRUCCIONES DE SEGURIDAD 51

CONTENIDO DEL EMBALAJE 54

INTRODUCCIÓN 54

CONEXIONES, MANDOS E INDICADORES 55

CONEXIONES DEL BLOQUE DE TERMINALES 57

EJEMPLO DE CONEXIÓN 58

MONTAJE BAJO/SOBRE LA MESA 59

CUIDADO, MANTENIMIENTO Y REPARACIÓN 60

DIMENSIONES 61

DATOS TÉCNICOS 62

DISPOSICIÓN 64

DECLARACIONES DEL FABRICANTE 65

POLSKI

INFORMACJE DOTYCZĄCE NINIEJSZEJ

INSTRUKCJI OBSŁUGI 66

STOSOWANIE ZGODNIE Z PRZEPISAMI 66

OBJAŚNIENIA TERMINÓW I SYMBOLI 66

INSTRUKCJE BEZPIECZEŃSTWA 67

ZAWARTOŚĆ OPAKOWANIA 70

WPROWADZENIE 70

PRZYŁĄCZA, ELEMENTY OBSŁUGI I WSKAŹNIKI 71

POŁĄCZENIA TERMINALI ZACISKOWYCH 73

PRZYKŁAD POŁĄCZENIA 74

MONTAŻ POD / NA BLACIE 75

PIELĘGNACJA, KONSERWACJA I NAPRAWA 76

WYMIARY 77

DANE TECHNICZNE 78

DYSPOZYCJA 80

OŚWIADCZENIA PRODUCENTA 81

ITALIANO

INFORMAZIONI SU QUESTE ISTRUZIONI

PER L‘USO 82

UTILIZZO IN CONFORMITÀ ALLE NORMATIVE 82

SPIEGAZIONI DI TERMINI E SIMBOLI 82

ISTRUZIONI DI SICUREZZA 83

CONTENUTO DELL‘IMBALLAGGIO 86

INTRODUZIONE 86

CONNESSIONI, ELEMENTI DI COMANDO E

DI VISUALIZZAZIONE 87

COLLEGAMENTI DELLA MORSETTIERA 89

ESEMPIO DI CONNESSIONE 90

MONTAGGIO SOTTO/SU TAVOLO 91

CURA, MANUTENZIONE E RIPARAZIONE 92

INGOMBRO 93

DATI TECNICI 94

MALTIMENTO 96

DICHIARAZIONI DEL PRODUTTORE 97

4

ENGLISH

YOU HAVE MADE THE RIGHT CHOICE!

We have designed this product to operate reliably over many years. LD Systems stands for this

with its name and many years of experience as a manufacturer of high-quality audio products.

Please read this User‘s Manual carefully, so that you can begin making optimum use of your

LD Systems product quickly. You can find more information about LD SYSTEMS at our Internet

site WWW.LD-SYSTEMS.COM

ABOUT THIS MANUAL

• Read the safety instructions and the entire manual carefully before commissioning.

• Observe the warnings on the unit and in the operating instructions.

• Always keep the operating instructions within reach.

• If you sell or pass on the appliance, be sure to hand over these operating instructions as well,

as they are an essential part of the product.

INTENDED USE

The product is a device for professional audio installation! The product has been developed for

professional use in the field of audio installation and is not intended for use in households!

Furthermore, this product is intended for installation by qualified persons with specialist

knowledge and for operation by instructed persons! The use of the product outside the specified

technical data and operating conditions is considered as not intended! Liability for damages and

third party damages to persons and property due to non-intended use is excluded!

The product is not suitable for:

• Persons (including children) with limited physical, sensory or mental capabilities or lack of

experience and knowledge.

• Children (children must be instructed not to play with the device)

EXPLANATIONS OF TERMS AND SYMBOLS

1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately

dangerous situations or conditions for life and limb.

2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially

dangerous situations or conditions for life and limb.

3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate

situations or conditions that may lead to injury.

4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations

or states that can lead to damage to property and/or the environment.

This symbol identifies hazards that can cause electric shock.

This symbol identifies hazardous areas or hazardous situations.

This symbol indicates hazards caused by hot surfaces.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

5

This symbol indicates dangers due to high volume levels.

This symbol denotes a device that does not contain any user-serviceable parts.

This symbol indicates additional information on the operation of the product.

SAFETY INSTRUCTIONS

DANGER:

1. Do not open the device and do not perform any modifications.

2. If your device no longer functions properly, if liquids or objects get inside it or if it

has been damaged in any other way, switch it off immediately and disconnect it

from the mains. The device may be repaired only by authorised repair technicians.

3. For devices of protection class 1, the protective conductor must be connected

correctly. Never disconnect the protective conductor. Devices of protection

class 2 do not have a protective conductor.

4. Ensure that live cables are not kinked or otherwise mechanically damaged.

5. Never bypass the device fuse.

WARNING:

1. The device may not be operated if it shows obvious signs of damage.

2. The device may only be installed in a voltage-free state.

3. If the mains cable of the device is damaged, do not operate the device.

4. Permanently connected power cables may only be replaced by a qualified person.

CAUTION:

1. Do not operate the device if it has been exposed to strong temperature fluctuations

(for example, after transport). Moisture and condensate could damage the device.

Do not switch on the device until it has reached ambient temperature.

2. Make sure that the voltage and frequency of the mains supply match the values

indicated on the device. If the device has a voltage selector switch, do not connect

the device until it is set correctly. Use only suitable power cords.

3.

To completely disconnect the device from the power supply, unplug the power cable or

power adapter from the outlet. It is not sufficient to press the on/off switch on the unit.

4. Only replace the fuse with a fuse of the same type and rating indicated on the device.

5. Make sure that suitable measures have been taken against overvoltage

(e.g. lightning strike).

6. Observe the specified maximum output current on devices with Power Out

connection. Ensure that the total current consumption of all connected devices

does not exceed the specified value.

7. Replace pluggable mains cables only with original cables.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

6

DANGER:

1. Choking hazard! Plastic bags and small parts must be kept out of reach of persons

(including children) with reduced physical, sensory or mental capabilities.

2. Danger of falling down! Make sure that the device is securely installed and cannot

fall down. Only use suitable stands or mountings (especially for fixed installations).

Make sure that accessories are properly installed and secured. Make sure that

applicable safety regulations are observed.

WARNING:

1. Use the device only in the manner intended.

2. Operate the device only with the accessories recommended and intended by the

manufacturer.

3. During installation, observe the safety regulations applicable in your country.

4. After connecting the device, check all cable routes to prevent damage or accidents,

e.g. due to tripping hazards.

5. It is essential to observe the specified minimum distance to normally flammable

materials! If this is not explicitly stated, the minimum distance is 0.3 m.

CAUTION:

1. In the case of moving components such as mounting brackets or other moving

components, there is a possibility of jamming.

2. In the case of units with motor-driven components, there is a risk of injury from the

movement of the unit. Sudden device movement can cause shockreactions.

CAUTION:

1. Do not install or operate the unit near any radiators, heat registers, stoves, or other

sources of heat. Always ensure that the device is installed in such a way that it is

sufficiently cooled and cannot overheat.

2. Do not place ignition sources such as lighted candles near the unit.

3. Ventilation openings must not be covered and fans must not be blocked.

4.

Use the original packaging or packaging provided by the manufacturer for transport.

5. Avoid shocks or impacts to the device.

6. Observe the IP protection class as well as the ambient conditions such as

temperature and humidity according to the specification.

7. Devices may be subject to continuous development. In case of deviating

information on operating conditions, performance or other device characteristics

between operating instructions and device labeling, the information on the device

always has priority.

8. The device is not suitable for tropical climates and for operation above 2000 m

above sea level.

9.

Unless explicitly stated, the device is not suitable for operation under marine conditions.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

7

NOTICE:

In the case of conversion or retrofit kits or accessories provided by the manufacturer,

be sure to follow the enclosed instructions.

CAUTION HIGH VOLUME AUDIO PRODUCTS!

This device is intended for professional use. Commercial operation of this device is

subject to applicable national regulations and guidelines for accident prevention.

Hearing Damage from High Volume and Continuous Exposure: Use of this product

may generate high sound pressure levels (SPL) that can cause hearing damage.

Avoid exposure to high volume levels.

NOTES FOR INDOOR INSTALLATION EQUIPMENT

1. Units for installation applications are designed for continuous operation.

2. Units for indoor installation are not weatherproof.

3. Surfaces and plastic parts of installation equipment can also age, e.g. due to UV

radiation and temperature fluctuations.

This does not usually lead to functional restrictions.

4. with permanently installed units, the deposition of impurities, e.g. dust, is to be

expected. Be sure to observe the care instructions.

5. Unless explicitly stated otherwise on the unit, the units are intended for

installation heights of less than 5 m.

PACKAGING CONTENT

Remove the product from the packaging and remove all packaging material.

Please check the completeness and integrity of the delivery and notify your distribution

partner immediately after purchase if the delivery is not complete or if it is damaged.

The packaging includes:

• 1 x AMP 106 T installation amplifier

• 1 x power supply unit

• 1 set of terminal blocks

• 1 x mounting set for under- or on-table mounting

• User manual

INTRODUCTION

The AMP 106 T is a 1-channel mini installation amplifier from the TICA® series and is ideal for use

in sound installations where small dimensions, passive cooling and high efficiency are required.

The highly efficient 60W Class-D amplifier, with Lo-Z / Hi-Z selector switch and 4 Ohm / 100V / 70V

outputs, is convection-cooled and a straightforward solution for professional installers.

With a size of 1/4 19“ rack, 1U, the mini AMP 106 T fits perfectly in any installation location.

The supplied mounting plates offer maximum flexibility and facilitate discreet mounting,

whether on the table or on the wall. Installation in suspended ceilings is also no problem

thanks to the compact size and passive cooling.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

8

For space-saving installation in the rack, an optional rack tray offers you the possibility to place

up to four products of the TICA® series next to each other.

Terminal strip connections on the balanced line inputs and speaker outputs make wiring

particularly easy.

Thanks to the option of remote control through third-party devices, you can conveniently adjust

the volume or put the power amplifier into standby mode at any time, even when it‘s hidden.

The perfect solution for professional installers and users looking for a compact, highly efficient

and easy-to-integrate solution.

FEATURES

• Professional mini amplifier

• 60W Class-D amplifier with Lo-Z / Hi-Z selector switch and 4 Ohm / 100V / 70V outputs

• Small form factor 1/4 19" rack, 1U

• Silent operation due to passive cooling

• Third-party connectivity for remote standby and volume control

• External wide-range switch mode power supply

• Incl. mounting plates for inconspicuous audio installations

• Suitable for fixed installation in suspended ceilings

• Balanced line input and speaker output with terminal strips

• User-friendly front panel with signal, clip and protection LEDs

• Optional rack tray for combination with other products of the TICA® series

CONNECTIONS, OPERATING AND DISPLAY ELEMENTS

45

63

8

7

2

1

1 TERMINAL BLOCK CONNECTION FOR POWER SUPPLY

Terminal block connection for the device‘s power supply. To avoid damage to the unit, please use

only the original power supply (power supply unit included).

2 STRAIN RELIEF

Use the strain relief for the flexible cable of the power supply unit to protect the device‘s power

terminal block connector and the power supply terminal block from damage and to prevent the

terminal block from being pulled out unintentionally.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

9

3 LINE IN L/R

Analogue audio inputs with balanced terminal block connections. The +, - and G poles are for the

balanced input signal (suitable for unbalanced cabling). The signals of the inputs L and R are

internally mono summed. Terminal blocks are included in the packaging content.

4 OUTPUT

The loudspeaker output with terminal block connection (terminal block included in the packaging

content) enables the use of low-impedance loudspeakers with an impedance of at least 4 ohms

(switch LO-Z/HI-Z in position LO-Z) as well as 70 V or 100 V loudspeakers (switch LO-Z/HI-Z in

position HI-Z). Please observe the correct assignment of the terminal block poles (see TERMINAL

BLOCK CONNECTIONS in this manual). The total power handling of the connected speakers should

be approximately equal to the amplifier power.

5 HI-Z / LO-Z

Before operating the unit, make sure that the switch is in the correct position!

Low impedance loudspeakers: LO-Z

70 V and 100 V loudspeakers: HI-Z

6 SETTINGS

DIP switch 1 STANDBY: Move the switch to the ON position to activate the automatic

standby function of the unit. If the standby function is activated, the amplifier is automatically

set to standby mode if no audio signal is detected for about 20 minutes. This reduces power

consumption in a sensible way. As soon as an audio signal is present, the amplifier is

automatically booted up from standby mode and is fully operational again within approximately

3 seconds. The power symbol on the front panel lights up red in standby mode. If the power

symbol lights up white, the unit is ready for operation.

DIP switch 2 HPF: Move the switch to ON position to activate the high-pass filter (HPF 110 Hz).

7 STANDBY

Standby mode can be activated manually with the help of an external button (momentary

switch). Press the button to activate standby mode and mute the speaker outputs. Press the

button again to end standby mode. The standby function via external button has priority over

the automatic standby function (see SETTINGS).

8 VCA

Terminal block connector for the use of an external volume control. The maximum volume is set

on the VOLUME control on the front panel. Once you have set the maximum volume, you can use

the external volume control to adjust the volume of the unit from the minimum value to the

preset value as desired. Please observe the correct assignment of the terminal block poles

(see TERMINAL BLOCK CONNECTIONS in this manual).

11 12

10

13 9

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

10

9 POWER SYMBOL

The power symbol lights up white when the installation amplifier is ready for operation.

In standby mode, the symbol lights up red.

10 VOLUME

Volume control. Turning to the right increases the volume, turning to the left decreases it.

11 SIG (SIGNAL)

As soon as an audio signal is present at the amplifier, the signal indicator lights up white.

12 CLIP

The CLIP indicator lights up when the amplifier is overdriven. In this case, reduce the volume

level. Failure to do so may result in distorted sound reproduction and damage to the amplifier

and speakers.

13 PROT (PROTECT)

The Protect indicator lights up permanently if the system is overloaded or overheats, in case

of a short circuit in the loudspeaker path and in case of a defect. The amplifier is automatically

muted. Disconnect the amplifier from the power supply and let it cool down for some time.

Eliminate a possible short circuit in the speaker path. Reconnect the amplifier to the power

supply. If the Protect indicator still lights up, there is a defect in the amplifier electronics.

Contact an authorised service workshop.

AIR VENTS

To prevent damage to the device, do not cover the ventilation openings on the left and right

sides and on the top and bottom of the device and ensure that air can circulate freely. Covering

the ventilation openings on the top or bottom of the enclosure when mounting it underneath

or on top of a table is not critical, as the cooling provided by the ventilation openings on the

remaining sides is sufficient.

TERMINAL BLOCK CONNECTIONS

LINE IN L / R CONNECTIONS STANDBY CONNECTIONS

balanced

unbalanced

momentary switch

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

11

CONNECTIONS VCA

Ground

5 V

Volume

OUTPUT CONNECTIONS

ATTENTION:

When wiring terminal blocks, please note the correct assignment of the poles/

terminals. The manufacturer accepts no liability for damage caused by faulty wiring!

CONNECTION EXAMPLE

ON

1 2

VOLUME

ON/STANDBY

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

12

UNDER / ON-TABLE MOUNTING

There are two recesses on the top and bottom of the enclosure, each with two M3 threaded

holes, for mounting underneath or on top of the table. Screw the two enclosed mounting plates

to the top or bottom side using the enclosed M3 countersunk screws. Now the amplifier can be

fixed in the desired position (see illustration, fixing screws not included). For tabletop mounting,

the four rubber feet must be removed beforehand.

Art No. XXX

PRODUCTNAME

GEZEICHNET

GEPRÜFT

GENEHMIGT

PRODUKTION

QUALITÄT

WENN NICHT ANDERS DEFINIERT:

BEMASSUNGEN SIND IN MILLIMETER

OBERFLÄCHENBESCHAFFENHEIT:

TOLERANZEN:

LINEAR:

WINKEL:

OBERFLÄCHENGÜTE:

NAME

SIGNATUR

DATUM

WERKSTOFF:

GEWICHT:

A2

BLATT 1 VON 2

MASSSTAB:1:1

ZEICHNUNGSNR.

BENENNUNG:

ÄNDERUNG

ZEICHNUNG NICHT SKALIEREN

ENTGRATEN

UND SCHARFE

KANTEN

BRECHEN

CARE, MAINTENANCE AND REPAIR

To ensure the proper functioning of the device in the long term, it must be cared for regularly

and serviced as required. The care and maintenance requirements depend on the intensity of

use and environment.

We generally recommend a visual inspection before each start-up. Furthermore, we recommend

carrying out all the maintenance measures listed below every 500 operating hours or, in the

case of less intensive use, after one year at the latest. Defects due to insufficient care may result

in limitations of the warranty claims.

MAINTENANCE (user performable)

WARNING! Prior to any maintenance measures, the voltage supply and, if possible, all

device connections must be disconnected.

NOTE! Improper maintenance may impair the device or even destroy it.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

13

1. Housing surfaces must be cleaned with a clean, damp cloth.

Make sure that no moisture can penetrate the device.

2. Air inlets and outlets must be regularly cleaned of dust and dirt.

If compressed air is used, make sure that damage to the device is prevented

(e.g. fans must be blocked in this case).

3. Lines and plug contacts must be cleaned regularly and dust and dirt must be removed.

4. In general, no cleaning agents or abrasive agents may be used, otherwise the surface

finish may be damaged. Especially solvents, such as alcohol, can impair the function of

housing seals.

5. Devices must generally be stored dry and protected from dust and dirt.

MAINTENANCE AND REPAIR (by qualified personnel only)

DANGER! There are live components in the device. Even after disconnection from the

mains, residual voltage may still be present in the device, e.g. due to charged capacitors.

NOTE! There are no assemblies in the device that require maintenance by the user.

NOTE! Maintenance and repair work may only be carried out by qualified personnel

authorized by the manufacturer. In case of doubt, contact the manufacturer.

NOTE! Improperly performed maintenance work may affect the warranty claim.

DIMENSIONS

LD Systems

®

is a registered brand of the Adam Hall Group.

Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany

DESIGNED AND ENGINEERED IN GERMANY. Assembled in PRC



106

53

43

221,7

Art No. XXX

PRODUCTNAME

GEZEICHNET

GEPRÜFT

GENEHMIGT

PRODUKTION

QUALITÄT

WENN NICHT ANDERS DEFINIERT:

BEMASSUNGEN SIND IN MILLIMETER

OBERFLÄCHENBESCHAFFENHEIT:

TOLERANZEN:

LINEAR:

WINKEL:

OBERFLÄCHENGÜTE:

NAME

SIGNATUR

DATUM

WERKSTOFF:

GEWICHT:

A2

BLATT 2 VON 2

MASSSTAB:1:1

ZEICHNUNGSNR.

BENENNUNG:

ÄNDERUNG

ZEICHNUNG NICHT SKALIEREN

ENTGRATEN

UND SCHARFE

KANTEN

BRECHEN

221,7

LD Systems

®

is a registered brand of the Adam Hall Group.

Adam-Hall-Str. 1 · 61267 Neu-Anspach · Germany

DESIGNED AND ENGINEERED IN GERMANY. Assembled in PRC



106

53

43

221,7

Art No. XXX

PRODUCTNAME

GEZEICHNET

GEPRÜFT

GENEHMIGT

PRODUKTION

QUALITÄT

WENN NICHT ANDERS DEFINIERT:

BEMASSUNGEN SIND IN MILLIMETER

OBERFLÄCHENBESCHAFFENHEIT:

TOLERANZEN:

LINEAR:

WINKEL:

OBERFLÄCHENGÜTE:

NAME

SIGNATUR

DATUM

WERKSTOFF:

GEWICHT:

A2

BLATT 2 VON 2

MASSSTAB:1:1

ZEICHNUNGSNR.

BENENNUNG:

ÄNDERUNG

ZEICHNUNG NICHT SKALIEREN

ENTGRATEN

UND SCHARFE

KANTEN

BRECHEN

221,7

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

14

TECHNICAL DATA

Item number LDAMP106T

Product type Installation power amplifier

Line inputs 2

Line input connectors balanced line inputs, pitch 3.81 mm terminal block (3-pin)

Line outputs 0

Powered outputs 1 with output mode selector (LO-Z / HI-Z)

Cooling system Convection cooling

Priority levels 1

Input Section

Nominal input sensitivity 8.5 dBu (sine 1 kHz, gain max)

Nominal input clipping 18 dBu (sine 1 kHz, gain 0dB)

THD+N < 0.02% (SPK OUT, 4 dBu, 20 kHz BW)

Frequency response 20 Hz – 20 kHz (LO-Z SPK OUT, –0.5 dB)

Input impedance 12 kohms (balanced)

SNR > 100 dB (SPK OUT, 8 dBu, gain max, 20 kHz BW, A-weighted)

SNR (best conditions) > 102 dB (SPK OUT, +13 dBu, 22 kHz BW, A-weighted)

CMRR > 48 dB (SPK OUT, 4 dBu 1 kHz)

Gain –33 to 18 dB

Connector 2 x 3.81 mm terminal block 3-pin

Standby wake up threshold –30 dBu

3rd Party Control

Main volume 10k (linear taper) External potentiometer, pitch 3.5 mm terminal block (3-pin)

Power standby External momentary button, pitch 3.5 mm terminal block (2-pin)

Amplier output

Type Class D

Amplifier outputs 1-channel, mono summed, LO-Z: 4 ohm minimum load, HI-Z 70 V or 100 V outputs

Connector 4-pin terminal block (pitch 5.08 mm)

RMS output power 60 W (continuous sine wave 1 kHz, 4 ohm load)

Peak output power 72 W (100 msec sine 1 kHz burst @ 4 ohm load)

Frequency response 15 Hz – 20 kHz (LO-Z, –1 dB)

20 Hz – 20 kHz (HI-Z, –1 dB)

High pass filter 110 Hz

Protection Over/Undervoltage, Overtemperature, Short-Circuit, DC-Detection

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

15

Item number LDAMP106T

Power Supply

Type External SMPS

Voltage range 100 VAC – 240 VAC (+–10%), 50 – 60 Hz

Mains fuse none

Secondary connector Terminal block 5.08 mm 2-pole

Secondary Voltage 24 V DC

Secondary Current 3,5 A

Primary connector IEC Jack

Safety class Class 1

Max power consumption 75 W (sine 1 kHz with 4 ohm load)

Idle power consumption 2 W (no signal input)

Standby power consuption < 1 W

Operating temperature 0°C – 40°C; < 85% humidity, non condensing

General

Time to standby 20 min.

Material Steel chassis, plastic front panel

Dimensions (w x h x d) 106 x 53 x 221.7 mm (height with rubber feet)

Weight 1.3 kg

Included accessories External power supply, mounting plates for surface mount applications,

terminal blocks for electrical connections.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

16

DISPOSAL

Packaging:

1. Packaging can be disposed of via the usual waste disposal channels.

2. Please separate the packaging according to the waste disposal and materials

regulations in your country.

Device:

1. This device is subject to the European Directive on Waste Electrical and Electronic

Equipment in its applicable version. WEEE Directive- Waste Electrical and Electroni-

cal Equipment. Old devices and batteries do not belong in household waste. The old

device or batteries must be disposed of via an approved waste disposal service or a

municipal waste disposal facility. Follow the directives in your country!

2. Follow the disposal laws in your country.

3. As a private customer, you can obtain information on environmentally friendly

disposal options from the retailer from whom you purchased the product or from

the relevant regional authorities.

Batteries and rechargeable batteries:

1. Batteries and rechargeable batteries do not belong in household waste. Batteries

and rechargeable batteries must be disposed of via an authorised disposal company

or a municipal disposal facility.

2. Observe all disposal laws and regulations applicable in your country.

3. As a private customer, you can obtain information on environmentally friendly

disposal options from the dealer from whom the product was purchased or from

the relevant regional authorities.

4. Appliances with batteries or accumulators that cannot be removed by the user

must be handed in at a collection point for electrical appliances.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

17

MANUFACTURER´S DECLARATIONS

MANUFACTURER‘S WARRANTY & LIMITATIONS OF LIABILITY

Adam Hall GmbH, Adam-Hall-Str. 1, D-61267 Neu Anspach / E-mail [email protected] /

+49 (0)6081 / 9419-0.

Our current warranty conditions and limitation of liability can be found at:

https://cdn-shop.adamhall.com/media/pdf/MANUFACTURERS-DECLARATIONS_LD_SYSTEMS.pdf.

Contact your distribution partner for service.

UKCA-CONFORMITY

Hereby, Adam Hall Ltd. declares that this product meets the following guidelines (where applicable)

Electrical Equipment (Safety) Regulations 2016

Electromagnetic Compatibility Regulations 2016 (SI 2016/1091)

The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Regulation 2012 (SI 2012/3032)

Radio Equipment Regulations 201 7(SI 2016/2015)

UKCA-DECLARATION OF CONFORMITY

Products that are subject to Electrical Equipment(Safety)Regulation 2016, EMC Regulation 2016 or

RoHS Regulation can be requested at

[email protected]. Products that are subject to the Radio Equipments Regulations 2017

(SI2017/1206) can be downloaded from

www.adamhall.com/compliance/

CE CONFORMITY

Adam Hall GmbH hereby confirm that this product meets the following guidelines

(where applicable):

R&TTE (1999/5/EC) or RED (2014/53/EU) as of June 2017.

Low Voltage Directive (2014/35/EU)

EMC Directive (2014/30/EU)

RoHS (2011/65/EU)

The complete Declaration of Conformity can be found at www.adamhall.com.

Furthermore, you can also request it at [email protected].

CE DECLARATION OF CONFORMITY

Declarations of conformity for products subject to the LVD, EMC, RoHS Directive

can be requested from [email protected].

Declarations of conformity for products subject to RED Directive

can be downloaded from www.adamhall.com/compliance/.

Subject to misprints and errors, as well as technical or other modifications!

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

18

DEUTSCH

SIE HABEN DIE RICHTIGE WAHL GETROFFEN!

Wir haben dieses Produkt so konzipiert, dass es über viele Jahre hinweg zuverlässig funktioniert.

Dafür steht LD Systems mit seinem Namen und seiner langjährigen Erfahrung als Hersteller von

hochwertigen Audioprodukten. Bitte lesen Sie diese Bedienungsanleitung sorgfältig durch,

damit Sie Ihr LD SYSTEMS Produkt schnell optimal nutzen können. Weitere Informationen über

LD SYSTEMS finden Sie auf unserer Internet-Seite WWW.LD-SYSTEMS.COM

INFORMATIONEN ZU DIESER BEDIENUNGSANLEITUNG

• Lesen Sie vor Inbetriebnahme die Sicherheitshinweise und die gesamte Anleitung aufmerksam durch.

• Beachten Sie die Warnungen auf dem Gerät und in der Bedienungsanleitung.

• Bewahren Sie die Bedienungsanleitung immer in Reichweite auf.

• Wenn Sie das Gerät verkaufen oder weitergeben, händigen Sie unbedingt auch diese

Bedienungsanleitung aus, da sie ein wesentlicher Bestandteil des Produkts ist.

BESTIMMUNGSGEMÄSSER GEBRAUCH

Das Produkt ist ein Gerät für die professionelle Audioinstallation!

Das Produkt wurde für den professionellen Einsatz im Bereich der Audioinstallation entwickelt

und ist nicht für den Einsatz in Haushalten vorgesehen!

Außerdem ist dieses Produkt für die Installation durch qualifizierte Personen mit

Fachkenntnissen und für die Bedienung durch eingewiesene Personen bestimmt!

Die Benutzung des Produkts außerhalb der spezifizierten technischen Daten und

Betriebsbedingungen gilt als nicht bestimmungsgemäß!

Haftung für Schäden und Drittschäden an Personen und Sachen durch nicht

bestimmungsgemäßen Gebrauch ist ausgeschlossen!

Das Produkt ist nicht geeignet für:

• Personen (einschließlich Kinder) mit eingeschränkten körperlichen, sensorischen oder

geistigen Fähigkeiten oder mangelnder Erfahrung und Kenntnis.

• Kinder (Kinder müssen angewiesen werden, nicht mit dem Gerät zu spielen).

BEGRIFFS- UND SYMBOLERKLÄRUNGEN

1. GEFAHR: Mit dem Wort GEFAHR, evtl. in Kombination mit einem Symbol, wird auf

unmittelbar gefährliche Situationen oder Zustände für Leib und Leben hingewiesen.

2. WARNUNG: Mit dem Wort WARNUNG, evtl. in Kombination mit einem Symbol, wird auf

potentiell gefährliche Situationen oder Zustände für Leib und Leben hingewiesen.

3. VORSICHT: Mit dem Wort VORSICHT, evtl. in Kombination mit einem Symbol, wird auf

Situationen oder Zustände hingewiesen, die zu Verletzungen führen können.

4. ACHTUNG:

Mit dem Wort ACHTUNG, evtl. in Kombination mit einem Symbol, wird auf Situa tionen

oder Zustände hingewiesen, die zu Sach- und/oder Umweltschäden führen können.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

19

Dieses Symbol kennzeichnet Gefahren, die einen elektrischen Schlag verursachen können.

Dieses Symbol kennzeichnet Gefahrenstellen oder gefährliche Situationen.

Dieses Symbol kennzeichnet Gefahren durch heiße Oberflächen.

Dieses Symbol kennzeichnet Gefahren durch hohe Lautstärken.

Dieses Symbol kennzeichnet ergänzende Informationen zur Bedienung des Produkts.

Dieses Symbol kennzeichnet ein Gerät, in dem sich keine vom Benutzer

austauschbaren Teile befinden.

SICHERHEITSHINWEISE

GEFAHR:

1. Öffnen Sie das Gerät nicht und verändern Sie es nicht.

2. Wenn Ihr Gerät nicht mehr ordnungsgemäß funktioniert, Flüssigkeiten oder Gegen-

stände in das Geräteinnere gelangt sind, oder das Gerät anderweitig beschädigt

wurde, schalten Sie es sofort aus und trennen es von der Spannungsversorgung.

Dieses Gerät darf nur von autorisiertem Fachpersonal repariert werden.

3. Bei Geräten der Schutzklasse 1 muss der Schutzleiter korrekt angeschlossen werden.

Unterbrechen Sie niemals den Schutzleiter. Geräte der Schutzklasse 2 haben keinen

Schutzleiter.

4. Sorgen Sie dafür, dass spannungsführende Kabel nicht geknickt oder anderweitig

mechanisch beschädigt werden.

5. Überbrücken Sie niemals die Gerätesicherung.

WARNUNG:

1. Das Gerät darf nicht in Betrieb genommen werden, wenn es offensichtliche

Beschädigungen aufweist.

2. Das Gerät darf nur im spannungsfreien Zustand installiert werden.

3. Wenn das Netzkabel des Geräts beschädigt ist, darf das Gerät nicht in Betrieb

genommen werden.

4. Fest angeschlossene Netzleitungen dürfen nur von einer qualifizierten Person

ersetzt werden.

DEUTSCHFRANCAIS

ESPAÑOL ENGLISH

ITALIANO POLSKI

20

ACHTUNG:

1. Nehmen Sie das Gerät nicht in Betrieb, wenn es starken Temperaturschwankungen

ausgesetzt war (beispielsweise nach dem Transport). Feuchtigkeit und Kondensat

könnten das Gerät beschädigen. Schalten Sie das Gerät erst ein, wenn es

Umgebungstemperatur erreicht hat.

2. Stellen Sie sicher, dass die Spannung und die Frequenz des Stromnetzes mit den

auf dem Gerät angegebenen Werten übereinstimmen. Verfügt das Gerät über

einen Spannungswahlschalter, schließen Sie das Gerät erst an, wenn dieser

korrekt eingestellt ist. Nutzen Sie nur geeignete Netzkabel.

3. Um das Gerät allpolig vom Netz zu trennen genügt es nicht, den Ein-/Aus-Schalter

am Gerät zu betätigen.

4. Stellen Sie sicher, dass die eingesetzte Sicherung dem auf dem Gerät

abgedruckten Typ entspricht.

5. Stellen Sie sicher, dass geeignete Maßnahmen gegen Überspannung

(z.B. Blitzschlag) ergriffen wurden.

6. Beachten Sie den angegebenen maximalen Ausgangsstrom an Geräten mit

Power Out Anschluss. Beachten Sie, dass die gesamte Stromaufnahme aller

angeschlossenen Geräte den vorgegebenen Wert nicht überschreitet.

7. Ersetzen Sie steckbare Netzleitungen nur durch Originalleitungen.

GEFAHR:

1. Erstickungsgefahr! Kunststoffbeutel und Kleinteile müssen außer Reichweite

von Personen (einschließlich Kindern) mit eingeschränkten körperlichen,

sensorischen oder geistigen Fähigkeiten aufbewahrt werden.

2. Gefahr durch Herabfallen! Stellen Sie sicher, dass das Gerät sicher installiert ist

und nicht herunterfallen kann. Verwenden Sie ausschließlich geeignete Stative

bzw. Befestigungen (im Besonderen bei Festinstallationen). Stellen Sie sicher,

dass Zubehör ordnungsgemäß installiert und gesichert ist. Achten Sie dabei

darauf, dass geltende Sicherheitsbestimmungen eingehalten werden.

WARNUNG:

1. Verwenden Sie das Gerät nur in der vorgesehenen Art und Weise.

2. Betreiben Sie das Gerät nur mit dem vom Hersteller empfohlenen und

vorgesehenen Zubehör.

3. Beachten Sie bei der Installation die für Ihr Land geltenden Sicherheitsvorschriften.

4. Überprüfen Sie nach dem Anschluss des Geräts alle Kabelwege, um Schäden oder

Unfälle, z. B. durch Stolperfallen zu vermeiden.

5. Beachten Sie unbedingt den angegebenen Mindestabstand zu normal entflamm -

baren Materialien! Sofern dieser nicht explizit ausgewiesen ist, beträgt der Mindest-

abstand 0,3 m.

ITALIANO

POLSKI

ESPAÑOL

FRANCAIS

DEUTSCHENGLISH

Strona jest ładowana ...

LD Systems AMP 106 T Instrukcja obsługi

LD Systems AMP 106 T Instrukcja obsługi

w innych językach