Hagerco 780-110HD - Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

Marka: Hagerco

Model: 780-110HD - Heavy Duty - Concealed Leaf Hinge

Typ: Instrukcja obsługi

ROTON INSTRUCTION SHEETPART NO: 75009010

Removable Electric for Concealed hinges – RETW Rev: 01.18.19

HAGER Companies, 139 Victor Street, St. Louis, MO 63104 (800) 325-9995

HAGER Companies - 139 Victor Street  St. Louis, MO 63104  (800 325 9995)  www.hagerco.com

Part No.: 75009010

REMOVABLE ELECTRIC THROUGH WIRE

Door and Frame Preparation

1. For grout filled frame, install a Mortar Box (HAGER 430). Failure to do so will void the hinge warranty.

2. Prepare the door and frame for installation using the standard installation instruction sheet furnished with the

hinge.

Installation

1. Attach the hinge to the door and frame using the standard installation instruction

sheet furnished with the hinge.

2. If the door will have a closer on it, disconnect the closer arm. The module is much

easier to install with the door fully open.

3. Place the marking template into the notched section of the hinge. Make sure it rests

flat against the mounting surface and to the outside edge of the hinge.

4. Using the transfer punch, center punch both the mounting holes and the wire

access hole. See Fig. 1. The middle hole is the wire access hole.

5. Repeat steps 2 and 3 for the opposite leaf of the hinge.

6. Drill only the 5/8” (3/4” max. for Quick Connect) diameter access hole in both the

frame rabbet and the door edge. For metal frames and doors ≤ 0.110” (2.8mm)

thick, it is not necessary to drill pilot holes for the mounting screws, if using the self-drilling screws provided. For metal

frames and doors > 0.110” (2.8mm) thick, drill the pilot holes for the mounting screws using a #16 (0.177”/4.5mm) bit,

if using the self-drilling screws provided. For wooden doors, drill pilot holes for the mounting screws using a #18

(0.170”/4.3mm) bit, if using the wood screws provided.

7. After drilling, remove any burrs or sharp edges from the holes to prevent damage to the wire leads.

8. Identify which leaf gears of the module matches the frame leaf of the installed hinge (the number of gear teeth are

different on the frame and door leafs).

9. Connect the system wires from the frame to the appropriate leads of the frame leaf side of the module (as described

in the system wiring diagram). Insulate the bare end of any unused wires.

Red

Yellow

Violet

Grey

White w/Grey

White w/Red

White w/Violet

White w/Yellow

Blue

Brown

Red

Yellow

Violet

Grey

White w/Grey

White w/Red

White w/Violet

White w/Yellow

Blue

Brown

Fig. 1

CORRECT INTERLOCKING

GEARS

(END VIEW)

FRAME / DOOR

SIDE

PLACE THESE

LOOPED WIRES

INSIDE COVER

CHANNEL TO

PREVENT PINCHING

OR CUTTING WIRES

COUTERSUNK

HOLE SIDE

DOOR PREP HOLE LOCATIONS

ROTON INSTRUCTION SHEETPART NO: 75009010

Removable Electric for Concealed hinges – RETW Rev: 01.18.19

HAGER Companies, 139 Victor Street, St. Louis, MO 63104 (800) 325-9995

HAGER Companies - 139 Victor Street  St. Louis, MO 63104  (800 325 9995)  www.hagerco.com

Part No.: 75009010

MAXIMUM ELECTRICAL

RATING CONTACT THROUGH WIRE

Volts: 48V DC/AC

Amperes: 3.5Amps Continuous

10. Insert the frame leaf module into the notch of the hinge

while carefully pushing the wires back through the

access hole in the frame, making sure they are placed

so they will not be cut or pinched as the installation is

completed. Attach the module to the frame, leaving the

screws slightly loose. For metal doors, use the #12 self-

drilling screws provided (recommended driver speed

1,900-2,500 RPM). For wood doors, use the #12 wood

screws provided.

11. Connect the system wires from the door to the

appropriate leads of the door leaf side of the module.

See illustration to the right. Insulate the bare end of any

unused wires.

12. Insert the door leaf module into the notch of the hinge

while carefully pushing the wires back through the access

hole in the door, making sure they are placed so they will

not be cut or pinched as the installation is completed.

Move the door to at least 90 degrees to verify the gears

align with the gears in the frame leaf. Make sure the

gears you can see are aligned with the other hinge gears

above and below. Using the #12 self-drilling screws to

attach the module to the door, ensure the proper interlock

of gear teeth of the two module components and that the

looped wires are placed into the cover channel.

13. Tighten all screws in the module, making sure that both

leaves of the module are flat and flush with the hinge

leaves. A quick visual inspection should show all gears

are vertically aligned. Cycle door open and closed to

ensure proper alignment with hinge and module.

14. Reattach door closer arm if present.

Hagerco 780-110HD - Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

Marka: Hagerco

Model: 780-110HD - Heavy Duty - Concealed Leaf Hinge

Typ: Instrukcja obsługi

ściągnij PDF

raport

w innych językach

English: Hagerco 780-110HD - Heavy Duty - Concealed Leaf Hinge Operating instructions

Hagerco 780-110HD - Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

Hagerco 780-110HD - Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

w innych językach

Inne dokumenty