Hagerco 1200-600XHD - Extra Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

Typ
Instrukcja obsługi
ROTON INSTRUCTION SHEETPART NO: 75009010
Removable Electric for Concealed hinges RETW Rev: 01.18.19
HAGER Companies, 139 Victor Street, St. Louis, MO 63104 (800) 325-9995
HAGER Companies - 139 Victor Street St. Louis, MO 63104 (800 325 9995) www.hagerco.com
Part No.: 75009010
REMOVABLE ELECTRIC THROUGH WIRE
Door and Frame Preparation
1. For grout filled frame, install a Mortar Box (HAGER 430). Failure to do so will void the hinge warranty.
2. Prepare the door and frame for installation using the standard installation instruction sheet furnished with the
hinge.
Installation
1. Attach the hinge to the door and frame using the standard installation instruction
sheet furnished with the hinge.
2. If the door will have a closer on it, disconnect the closer arm. The module is much
easier to install with the door fully open.
3. Place the marking template into the notched section of the hinge. Make sure it rests
flat against the mounting surface and to the outside edge of the hinge.
4. Using the transfer punch, center punch both the mounting holes and the wire
access hole. See Fig. 1. The middle hole is the wire access hole.
5. Repeat steps 2 and 3 for the opposite leaf of the hinge.
6. Drill only the 5/8” (3/4” max. for Quick Connect) diameter access hole in both the
frame rabbet and the door edge. For metal frames and doors ≤ 0.110” (2.8mm)
thick, it is not necessary to drill pilot holes for the mounting screws, if using the self-drilling screws provided. For metal
frames and doors > 0.110” (2.8mm) thick, drill the pilot holes for the mounting screws using a #16 (0.177”/4.5mm) bit,
if using the self-drilling screws provided. For wooden doors, drill pilot holes for the mounting screws using a #18
(0.170”/4.3mm) bit, if using the wood screws provided.
7. After drilling, remove any burrs or sharp edges from the holes to prevent damage to the wire leads.
8. Identify which leaf gears of the module matches the frame leaf of the installed hinge (the number of gear teeth are
different on the frame and door leafs).
9. Connect the system wires from the frame to the appropriate leads of the frame leaf side of the module (as described
in the system wiring diagram). Insulate the bare end of any unused wires.
Red
Yellow
Violet
Grey
White w/Grey
White w/Red
White w/Violet
White w/Yellow
Blue
Brown
Red
Yellow
Violet
Grey
White w/Grey
White w/Red
White w/Violet
White w/Yellow
Blue
Brown
CORRECT INTERLOCKING
GEARS
(END VIEW)
FRAME / DOOR
SIDE
PLACE THESE
LOOPED WIRES
INSIDE COVER
CHANNEL TO
PREVENT PINCHING
OR CUTTING WIRES
COUTERSUNK
HOLE SIDE
DOOR PREP HOLE LOCATIONS
ROTON INSTRUCTION SHEETPART NO: 75009010
Removable Electric for Concealed hinges RETW Rev: 01.18.19
HAGER Companies, 139 Victor Street, St. Louis, MO 63104 (800) 325-9995
HAGER Companies - 139 Victor Street St. Louis, MO 63104 (800 325 9995) www.hagerco.com
Part No.: 75009010
MAXIMUM ELECTRICAL
RATING CONTACT THROUGH WIRE
Volts: 48V DC/AC
Amperes: 3.5Amps Continuous
10. Insert the frame leaf module into the notch of the hinge
while carefully pushing the wires back through the
access hole in the frame, making sure they are placed
so they will not be cut or pinched as the installation is
completed. Attach the module to the frame, leaving the
screws slightly loose. For metal doors, use the #12 self-
drilling screws provided (recommended driver speed
1,900-2,500 RPM). For wood doors, use the #12 wood
screws provided.
11. Connect the system wires from the door to the
appropriate leads of the door leaf side of the module.
See illustration to the right. Insulate the bare end of any
unused wires.
12. Insert the door leaf module into the notch of the hinge
while carefully pushing the wires back through the access
hole in the door, making sure they are placed so they will
not be cut or pinched as the installation is completed.
Move the door to at least 90 degrees to verify the gears
align with the gears in the frame leaf. Make sure the
gears you can see are aligned with the other hinge gears
above and below. Using the #12 self-drilling screws to
attach the module to the door, ensure the proper interlock
of gear teeth of the two module components and that the
looped wires are placed into the cover channel.
13. Tighten all screws in the module, making sure that both
leaves of the module are flat and flush with the hinge
leaves. A quick visual inspection should show all gears
are vertically aligned. Cycle door open and closed to
ensure proper alignment with hinge and module.
14. Reattach door closer arm if present.
  • Page 1 1
  • Page 2 2

Hagerco 1200-600XHD - Extra Heavy Duty - Concealed Leaf Hinge Instrukcja obsługi

Typ
Instrukcja obsługi