Warwick BC40 Instrukcja obsługi

Marka: Warwick

Model: BC40

Kategoria: Akcesoria gitarowe

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

OWNER’S MANUAL

BASS COMBO AMPLIFIERS

BC10 BC20 BC40

BC80 BC150

Family Owned ◊ Solar Powered ◊ Sustainably Manufactured in a Green Environment

INDEX

Introduction 5

Safety Instructions 6

Product Information

BC10 8

BC20 10

BC40 12

BC80 14

BC150 16

Troubleshooting 18

INTRODUCTION

A series of compact ampliﬁers for Bass instruments like nothing you have seen or heard before. These full frequency,

extended headroom, integrated combo amps could be used for virtually any ampliﬁed instrument but are speciﬁcally tuned

to the unique needs of Electric and Upright Bassists.

Our considerations in these amp designs were multifold and our objectives are to provide:

• An affordable amplier for the discerning musician.

• A gigging amplier for the seasoned professional.

• A teacher’s amp where both the student and the teacher can plug in simultaneously while playing musical examples

with a music player through the auxiliary input.

• An amp for rehearsals, where space and sound levels are limited.

Here is a short explanation of the underlying design concepts.

CLASS A OPERATION

Class A ampliﬁers are typically more linear and as such are less complex than other ampliﬁer classes. In Class A ampliﬁers, the

ampliﬁcation circuitry is designed so that it is always conducting electrical current. This means that the active elements are always on,

thus avoiding the problem of crossover distortion.

LOW-Z CIRCUITRY

Thermal noise is a critical design issue when it comes to audio electronics. By lowering the impedance of components inside an

electronic circuit, the overall thermal noise is substantially reduced. The Low-Z circuitry inside all of our ampliﬁers makes it possible to

achieve consistently noise-free operation.

DYNAMIC DISTORTION LIMITER

Distortion occurs when an ampliﬁer works beyond its range, when the power supply cannot supply the power any more to

take the amp higher. A common method to control distortion in amps is to use a limiter, a device that stops the signal going

beyond a speciﬁc level. Audio limiters work by setting a threshold signal level where the circuit kicks in and keeps signal

levels within the capabilities of the power supply. This method is not very precise and often causes audible effects such as

pumping and thumps.

We designed a circuit that instead reads the distortion level in the power amp and starts limiting as soon as the amp shows

even miniscule amounts of distortion. This means our amps always stay within 0.3% distortion (THD) when most amps are

rated at between 5-10% distortion (that means that to get your 20 Watt out of a 20 Watt amp you will get it audibly distorted

and if you want a clean signal the power will be a lot less). There are desirable types of distortion, but these are not usually

associated with transistor ampliers, but more commonly associated with tube amps and effect pedals. Warwick’s goal is to

give the user a great, clean sound allowing the user to decide how much, and what kind of distortion to employ.

INTEGRATED SPEAKER DESIGN

All the speaker drivers and cabinets have been designed in tandem with the electronics to create units that work together

efﬁciently. Careful consideration has been taken to modify all parameters, thereby achieving the best results in sound and

performance. All components reﬂect a custom designed solution to give the end user optimum control over his/her tone,

volume and conﬁguration.

SAFETY INSTRUCTIONS

Caution: To reduce the risk of electrical shock, do not remove the

cover as there are no user serviceable parts inside. Refer servicing

to qualiﬁed personnel.

This symbol, wherever it appears, alerts you to the presence of noninsulated

dangerous voltage inside the enclosure - voltage that may

be sufﬁcient to constitute risk of shock.

This symbol, wherever it appears, alerts you to important operating

and maintenance instructions in the accompanying literature. Read

the manual.

WARNING!

This ampliﬁer is capable of producing high sound pressure levels. Continued exposure to these high sound pressure levels

can cause permanent and irreversible hearing damage. Ear protection is recommended if unit is operated at high volume for

long period of time. If you experience any hearing loss or ringing in the ears you should consult a doctor.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions

2. Keep these instructions

3. Heed all warnings

4. Follow all instructions

5. Do not use this apparatus near water

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider

than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the

point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with

the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug the apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed personnel. Servicing is required when the apparatus has been damaged in any way,

such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has

been exposed to rain or moisture, does not operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions

2. Keep these instructions

3. Heed all warnings

4. Follow all instructions

5. Do not use this apparatus near water

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider

than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is

provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the

point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with

the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13. Unplug the apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed personnel. Servicing is required when the apparatus has been damaged in any way,

such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has

been exposed to rain or moisture, does not operate normally, or has been dropped.

15. WARNING: To reduce the risk of ﬁre or electric shock, do not expose this apparatus to rain or moisture.

The apparatus shall not be exposed to dripping or splashing and that objects ﬁlled with liquids, such as vases,

shall not be placed on apparatus.

16. Never set the ampliﬁer on a support that might give out under its weight.

17. WARNING: The mains plug used as disconnect device, the disconnect device shall remain readily operable.

18. Replace fuse with rated value, never bridge defective fuses. Before changing fuse disconnect power cable from unit!

19. Correct Disposal of this product. This marking indicates that this product should not be disposed

with other household wastes throughout the EU. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material

resources. To return your used device, please use the return and collection systems or contact the retailer where the

product was purchased. They can take this product for environmental safe recycling.

FOR BC10, BC20, BC40, and BC80:

These ampliﬁers are double insulated electrical appliances whereas BC150 has a protective earthing/grounding

connection and will be discussed in the next chapter.

This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not

require a safety connection to electrical earth (grounding).

FOR BC150:

1. The apparatus should be connected to a mains socket outlet with a protective earthing/grounding connection.

2. Replace fuse with identically rated fuse and never bridge defective fuses. Before changing fuse, disconnect

power cable from unit!

BC10

• Combo amplier for bass instruments

• Passive and active inputs

• Class-A preamp with Low-Z circuitry for minimum noise and

maximum headroom

• 10 watt power amp

• 8” Warwick WXC 8/8 bass driver

• 3-Way EQ with controls for bass, mid and treble

• DDL (Dynamic Distortion Limiter) for distortion-free reproduction at all levels

• Aux mini jack stereo input (iPod, MP3 player, CD player)

• Self-cooling construction (fanless operation)

• Dedicated stereo headphone amplier

• Bass reex speaker cabinet

• Protective speaker grille of rugged steel

• Weight: 6,5 kgs / 13.2 lbs.

• Dimensions: (W/H/D) 320mm x 250mm x 220mm / 12.6” x 9.8” x 8.7”

TECHNICAL SPECIFICATIONS:

Input sensitivity:

Active input: 360mV/50K Ω Output Power: 10W @ 8 Ω

Passive input: 110mV/500K Ω Frequency response: 20Hz-20kHz +/-0.5 dB

Aux input: 750mV/50K Ω THD less than 0.3% at rated output power

Power consumption: 22W

Tone controls:

Bass: +/- 12dB @ 60Hz Speaker speciﬁcations:

Mid: +/- 12dB @ 800Hz 8” Bass Driver: 10W, Impedance: 8 Ω, SPL: 90 dB,

Treble: +/- 12dB @ 10kHz Frequency response: 80Hz - 10kHz

GETTING STARTED

1. Unpacking – Carefully unpack unit from the carton box.

2. Connecting to power – Set the power switch in off position, connect the supplied power cord to the ampliﬁer and

then connect the same cord into AC outlet of proper voltage.

3. Setting front panel controls – Set VOLUME control to zero, all other controls should be settled to neutral, middle

position.

4. Connecting instrument – Using an instrumental cable (shielded) connect your instrument to the proper ACTIVE or

PASSIVE input. Turn all volume controls of your guitar to their maximum. Now press power switch on.

5. Adjusting your individual settings – Set the VOLUME to the value you wish to play, you should now hear sound from

the speaker. Adjust controls to your liking.

FRONT PANEL CONTROLS

ACTIVE – Input to plug in instrument using shielded guitar cable. This input is low sensitivity to suit the output

from instruments with active electronics.

PASSIVE – Input to plug in instrument using shielded guitar cable. This input is high sensitivity to suit the output

from instruments with passive electronics.

VOLUME – Controls the sound level of your instrument. Adjust this for your preferred playing loudness.

BASS – Shelving Bass Control gives +/- 12 dB gain at 60 Hz. The control is ﬂat at the center position.

MIDDLE – Peaking Middle Control gives +/- 12 dB gain at 800 Hz. The control is at at the center position.

TREBLE – Shelving Treble Control gives +/- 12 dB gain at 10 kHz. The control is ﬂat at the center position.

AUX IN – Input to connect external sound source. This can be used for plugging a CD, tape or MP3 player into

the amp or for connecting an external preamp.

HEADPHONE – For practice use in situations when speakers are too loud. Dedicated Stereo Headphone amp where the

aux input will be played back in stereo and the instrument signal will be reproduced in the center of the

stereo ﬁeld.

REAR PANEL CONTROLS

MAINS IN AC – Figure-eight socket for connection to the mains power supply.

POWER – On/off switch for main power. For your safety, remember to connect power cord to the ampliﬁer ﬁrst,

then to the AC outlet. After this is done, turn this switch on. It works backwards when you want

disconnect unit – ﬁrstly turn switch off, then disconnect cord from the AC outlet and ﬁnally disconnect

cord from ampliﬁer.

W BC 10 230 V

European Voltage

W BC 10 115 V

USA / Canada Voltage

W BC 10 DV 115/230 V

Brazil Voltage

W BC 10 100 V

Japan Voltage

ARTICLE

NUMBERS

BC20

• Combo amplier for bass instruments

• Passive and active inputs

• Class-A preamp with Low-Z circuitry for minimum noise and maximum

headroom

• 20 watt power amp

• 8” Warwick WXC 8/8 bass driver

• 2” Warwick WTR 2/8 neodymium high-frequency driver

• 3-Way EQ with controls for bass, mid and treble

• DDL (Dynamic Distortion Limiter) for distortion-free reproduction at

all levels

• Aux mini jack stereo input (iPod, MP3 player, CD player)

• Self-cooling construction (fanless operation)

• Dedicated stereo headphone amplier

• Bass reex speaker cabinet

• Protective speaker grille of rugged steel

• Weight: 9kgs/19.8lbs.

• Dimensions: (W/H/D) 310mm x 390mm x 370mm / 12.20” x 15.35” x 14.56”

TECHNICAL SPECIFICATIONS:

Input sensitivity: Output Power: 20W @ 8 Ω

Active input: 360mV/50K Ω Frequency response: 20Hz-20kHz +/-0.5 dB

Passive input: 110mV/500K Ω THD less than 0.3% at rated output power

Aux input: 750mV/50K Ω Power consumption: 43W

Tone controls: Speaker speciﬁcations:

Bass: +/- 12dB @ 60Hz 8” Bass Driver: 20W, Impedance: 8 Ω, SPL: 90 dB,

Mid: +/- 12dB @ 800Hz Frequency response: 80Hz - 10kHz

Treble: +/- 12dB @ 10kHz 2” HF Driver with Horn: 10W, Impedance: 8 Ω, SPL: 97 dB,

Frequency response: 1kHz - 20kHz

GETTING STARTED

1. Unpacking – Carefully unpack unit from the carton box.

2. Connecting to power – Set the power switch in off position, connect the supplied power cord to the ampliﬁer and

then connect the same cord into AC outlet of proper voltage.

3. Setting front panel controls – Set VOLUME control to zero, all other controls should be settled to neutral, middle

position.

4. Connecting instrument – Using an instrumental cable (shielded) connect your instrument to the proper ACTIVE or

PASSIVE input. Turn all volume controls of your guitar to their maximum. Now press power switch on.

5. Adjusting your individual settings – Set the VOLUME to the value you wish to play, you should now hear sound from

the speaker. Adjust controls to your liking.

FRONT PANEL CONTROLS

ACTIVE – Input to plug in instrument using shielded guitar cable. This input is low sensitivity to suit the output

from instruments with active electronics.

PASSIVE – Input to plug in instrument using shielded guitar cable. This input is high sensitivity to suit the output

from instruments with passive electronics.

VOLUME – Controls the sound level of your instrument. Adjust this for your preferred playing loudness.

BASS – Shelving Bass Control gives +/- 12 dB gain at 60 Hz. The control is ﬂat at the center position.

MIDDLE – Peaking Middle Control gives +/- 12 dB gain at 800 Hz. The control is at at the center position.

TREBLE – Shelving Treble Control gives +/- 12 dB gain at 10 kHz. The control is ﬂat at the center position.

AUX IN – Input to connect external sound source. This can be used for plugging a CD, tape or MP3 player into

the amp or for connecting an external preamp.

HEADPHONE – For practice use in situations when speakers are too loud. Dedicated Stereo Headphone amp where the

aux input will be played back in stereo and the instrument signal will be reproduced in the center of the

stereo ﬁeld.

REAR PANEL CONTROLS

MAINS IN AC – Figure-eight socket for connection to the mains power supply.

POWER – On/off switch for main power. For your safety, remember to connect power cord to the ampliﬁer ﬁrst,

then to the AC outlet. After this is done, turn this switch on. It works backwards when you want

disconnect unit – ﬁrstly turn switch off, then disconnect cord from the AC outlet and ﬁnally disconnect

cord from ampliﬁer.

W BC 20 230 V

European Voltage

W BC 20 115 V

USA / Canada Voltage

W BC 20 DV 115/230 V

Brazil Voltage

W BC 20 100 V

Japan Voltage

ARTICLE

NUMBERS

BC40

• Combo amplier for bass Instruments

• Passive and active inputs

• Class-A preamp with Low-Z circuitry for minimum noise and maximum

headroom

• 40 watt power amp

• 10” Warwick WXC 10/8 bass driver

• 2

”

Warwick WTR 2/8 neodymium high-frequency driver

• 3-Way EQ with controls for bass, mid and treble

• DDL (Dynamic Distortion Limiter) for distortion-free reproduction at all

levels

• Aux mini jack stereo input (iPod, MP3 player, CD player)

• Self-cooling construction (fanless operation)

• Dedicated stereo headphone amplier

• Bass reex speaker cabinet

• Protective speaker grille of rugged steel

• Weight: 15kgs/33lbs.

• Dimensions: (W/H/D) 360mm x 440mm x 370mm / 14.17” x 17.32” x 14.56”

TECHNICAL SPECIFICATIONS:

Input sensitivity: Output Power: 40W @ 8 Ω

Active input: 380mV/50K Ω Frequency response: 20Hz-20kHz +/-0.5 dB

Passive input: 130mV/500K Ω THD less than 0.3% at rated output power

Aux input: 630mV/50K Ω Power consumption: 78W

Tone controls: Speaker speciﬁcations:

Bass: +/- 12dB @ 60Hz 10” Bass Driver: 40W, Impedance: 8 Ω, SPL: 89 dB,

Mid: +/- 12dB @ 800Hz Frequency response: 50Hz - 8kHz

Treble: +/- 12dB @ 10kHz

2” HF Driver with Horn: 10W, Impedance: 8 Ω, SPL: 97 dB,

Frequency response: 1kHz - 20kHz

GETTING STARTED

1. Unpacking – Carefully unpack unit from the carton box.

2. Connecting to power – Set the power switch in off position, connect the supplied power cord to the ampliﬁer and

then connect the same cord into AC outlet of proper voltage.

3. Setting front panel controls – Set VOLUME control to zero, all other controls should be settled to neutral, middle

position.

4. Connecting instrument – Using an instrumental cable (shielded) connect your instrument to the proper ACTIVE or

PASSIVE input. Turn all volume controls of your guitar to their maximum. Now press power switch on.

5. Adjusting your individual settings – Set the VOLUME to the value you wish to play, you should now hear sound from

the speaker. Adjust controls to your liking.

FRONT PANEL CONTROLS

ACTIVE – Input to plug in instrument using shielded guitar cable. This input is low sensitivity to suit the output

from instruments with active electronics.

PASSIVE – Input to plug in instrument using shielded guitar cable. This input is high sensitivity to suit the output

from instruments with passive electronics.

VOLUME – Controls the sound level of your instrument. Adjust this for your preferred playing loudness.

BASS – Shelving Bass Control gives +/- 12 dB gain at 60 Hz. The control is ﬂat at the center position.

MIDDLE – Peaking Middle Control gives +/- 12 dB gain at 800 Hz. The control is at at the center position.

TREBLE – Shelving Treble Control gives +/- 12 dB gain at 10 kHz. The control is ﬂat at the center position.

AUX IN – Input to connect external sound source. This can be used for plugging a CD, tape or MP3 player into

the amp or for connecting an external preamp.

HEADPHONE – For practice use in situations when speakers are too loud. Dedicated Stereo Headphone amp where the

aux input will be played back in stereo and the instrument signal will be reproduced in the center of the

stereo ﬁeld.

REAR PANEL CONTROLS

MAINS IN AC – Figure-eight socket for connection to the mains power supply.

POWER – On/off switch for main power. For your safety, remember to connect power cord to the ampliﬁer ﬁrst,

then to the AC outlet. After this is done, turn this switch on. It works backwards when you want

disconnect unit – ﬁrstly turn switch off, then disconnect cord from the AC outlet and ﬁnally disconnect

cord from ampliﬁer.

W BC 40 230 V

European Voltage

W BC 40 115 V

USA / Canada Voltage

W BC 40 DV 115/230 V

Brazil Voltage

W BC 40 100 V

Japan Voltage

ARTICLE

NUMBERS

BC80

• Combo amplier for bass Instruments

• Passive and active inputs

• Line out

• Send/Return on front panel

• Class-A preamp with Low-Z circuitry for minimum noise and

maximum headroom

• 80 watt power amp

• 12” Warwick WXC 12/8 bass driver

• 2” Warwick WTR 2/8 neodymium highfrequency driver

• 4-Way EQ with controls for bass, low-mid, high-mid and treble

• DDL (Dynamic Distortion Limiter) for distortion-free reproduction

at all levels

• Aux mini jack stereo input (iPod, MP3 player, CD player)

• Self-cooling construction (fanless operation)

• Dedicated stereo headphone amplier

• Bass reex speaker cabinet

• Protective speaker grille of rugged steel

• Weight: 20kgs/44lbs.

• Dimensions: (W/H/D) 410mm x 490mm x 370mm / 16.14” x 19.29” x 14.56”

TECHNICAL SPECIFICATIONS:

Input sensitivity: Output Power: 80W @ 8 Ω

Active input: 380mV/50K Ω Frequency response: 20Hz-20kHz +/-0.5 dB

Passive input: 130mV/500K Ω THD less than 0.3% at rated output power

Aux input: 630mV/50K Ω Power consumption: 160W

Tone controls: Speaker speciﬁcations:

Bass: +/- 12dB @ 60Hz 12” Bass Driver: 80W, Impedance: 8 Ω, SPL: 94 dB,

Low Mid: +/- 8dB @ 800Hz Frequency response: 80Hz - 10kHz

High Mid: +/- 8dB @ 2500Hz

Treble: +/- 12dB @ 10kHz 2” HF Driver with Horn: 10W, Impedance: 8 Ω, SPL: 97 dB,

Frequency response: 1kHz - 20kHz

GETTING STARTED

1. Unpacking – Carefully unpack unit from the carton box.

2. Connecting to power – Set the power switch in off position, connect the supplied power cord to the ampliﬁer and

then connect the same cord into AC outlet of proper voltage.

3. Setting front panel controls – Set VOLUME control to zero, all other controls should be settled to neutral, middle

position.

4. Connecting instrument – Using an instrumental cable (shielded) connect your instrument to the proper ACTIVE or

PASSIVE input. Turn all volume controls of your guitar to their maximum. Now press power switch on.

5. Adjusting your individual settings – Set the VOLUME to the value you wish to play, you should now hear sound from

the speaker. Adjust controls to your liking.

FRONT PANEL CONTROLS

ACTIVE – Input to plug in instrument using shielded guitar cable. This input is low sensitivity to suit the output

from instruments with active electronics.

PASSIVE – Input to plug in instrument using shielded guitar cable. This input is high sensitivity to suit the output

from instruments with passive electronics.

VOLUME – Controls the sound level of your instrument. Adjust this for your preferred playing loudness.

BASS – Shelving Bass Control gives +/- 12 dB gain at 60 Hz. The control is ﬂat at the center position.

LOW MID – Peaking Middle Control gives +/- 12 dB gain at 800 Hz. The control is at at the center position.

HIGH MID – Peaking Middle Control gives +/- 12 dB gain at 2.5 kHz. The control is at at the center position.

TREBLE – Shelving Treble Control gives +/- 12 dB gain at 10 kHz. The control is ﬂat at the center position.

AUX IN – Input to connect external sound source. This can be used for plugging a CD, tape or MP3 player into

the amp or for connecting an external preamp.

HEADPHONE – For practice use in situations when speakers are too loud. Dedicated Stereo Headphone amp where the

aux input will be played back in stereo and the instrument signal will be reproduced in the center of the

stereo ﬁeld.

REAR PANEL CONTROLS

MAINS IN AC – Figure-eight socket for connection to the mains power supply.

POWER – On/off switch for main power. For your safety, remember to connect power cord to the ampliﬁer ﬁrst,

then to the AC outlet. After this is done, turn this switch on. It works backwards when you want

disconnect unit – ﬁrstly turn switch off, then disconnect cord from the AC outlet and ﬁnally disconnect

cord from ampliﬁer.

W BC 80 230 V

European Voltage

W BC 80 115 V

USA / Canada Voltage

W BC 80 DV 115/230 V

Brazil Voltage

W BC 80 100 V

Japan Voltage

ARTICLE

NUMBERS

BC150

• Combo amplier for bass Instruments

• Passive and active inputs

• Line out

• Send/Return on front panel

• Class-A preamp with Low-Z circuitry for minimum noise and

maximum headroom

• 150 watt power amp

• 15” Warwick WXC 15/8 bass driver

• 4” Warwick WTR 4/8 high-frequency driver

• 4-Way EQ with controls for bass, low-mid, high-mid and treble

• DDL (Dynamic Distortion Limiter) for distortion-free reproduction at

all levels

• Aux mini jack stereo input (iPod, MP3 player, CD player)

• Self-cooling construction (fanless operation)

• Dedicated stereo headphone amplier

• Bass reex speaker cabinet

• Protective speaker grille of rugged steel

• Weight: 24kgs/53lbs.

• Dimensions: (W/H/D) 530mm x 545mm x 380mm / 20.86” x 21.45” x 14.96”

TECHNICAL SPECIFICATIONS:

Input sensitivity: Output Power: 150W @ 8 Ω

Active input: 440mV/50K Ω Frequency response: 20Hz-20kHz +/-0.5 dB

Passive input: 120mV/500K Ω THD less than 0.3% at rated output power

Aux input: 660mV/50K Ω Power consumption: 300W

Tone controls: Speaker speciﬁcations:

Bass: +/- 12dB @ 60Hz 15” Bass Driver: 150W, Impedance: 8 Ω, SPL: 95 dB,

Low Mid: +/- 8dB @ 80Hz Frequency response: 70 - 3kHz

High Mid: +/- 8dB @ 2500Hz 4” HF Bass Driver with Horn: 30W, Impedance: 8 Ω, SPL: 98 dB,

Treble: +/- 12dB @ 10kHz Frequency response: 1.8kHz - 16kHz

GETTING STARTED

1. Unpacking – Carefully unpack unit from the carton box.

2. Connecting to power – Set the power switch in off position, connect the supplied power cord to the ampliﬁer and

then connect the same cord into AC outlet of proper voltage.

3. Setting front panel controls – Set VOLUME control to zero, all other controls should be settled to neutral, middle

position.

4. Connecting instrument – Using an instrumental cable (shielded) connect your instrument to the proper ACTIVE or

PASSIVE input. Turn all volume controls of your guitar to their maximum. Now press power switch on.

5. Adjusting your individual settings – Set the VOLUME to the value you wish to play, you should now hear sound from

the speaker. Adjust controls to your liking.

FRONT PANEL CONTROLS

ACTIVE – Input to plug in instrument using shielded guitar cable. This input is low sensitivity to suit the output

from instruments with active electronics.

PASSIVE – Input to plug in instrument using shielded guitar cable. This input is high sensitivity to suit the output

from instruments with passive electronics.

VOLUME – Controls the sound level of your instrument. Adjust this for your preferred playing loudness.

BASS – Shelving Bass Control gives +/- 12 dB gain at 60 Hz. The control is ﬂat at the center position.

LOW MID – Peaking Middle Control gives +/- 12 dB gain at 800 Hz. The control is at at the center position.

HIGH MID – Peaking Middle Control gives +/- 12 dB gain at 2.5 kHz. The control is at at the center position.

TREBLE – Shelving Treble Control gives +/- 12 dB gain at 10 kHz. The control is ﬂat at the center position.

AUX IN – Input to connect external sound source. This can be used for plugging a CD, tape or MP3 player into

the amp or for connecting an external preamp.

HEADPHONE – For practice use in situations when speakers are too loud. Dedicated Stereo Headphone amp where the

aux input will be played back in stereo and the instrument signal will be reproduced in the center of the

stereo ﬁeld.

REAR PANEL CONTROLS

MAINS IN AC – Figure-eight socket for connection to the mains power supply.

POWER – On/off switch for main power. For your safety, remember to connect power cord to the ampliﬁer ﬁrst,

then to the AC outlet. After this is done, turn this switch on. It works backwards when you want

disconnect unit – ﬁrstly turn switch off, then disconnect cord from the AC outlet and ﬁnally disconnect

cord from ampliﬁer.

W BC 150 230 V

European Voltage

W BC 150 115 V

USA / Canada Voltage

W BC 150 DV 115/230 V

Brazil Voltage

W BC 150 100 V

Japan Voltage

ARTICLE

NUMBERS

TROUBLESHOOTING

When your unit seems to not work properly, take a few minutes to troubleshoot before calling service. You can save yourself

time and money by doing it yourself, because the source of problem is often something quite simple.

What is the problem?

• There is no sound from the amp and LEDs don’t light up.

- Check your AC outlet

- Outlet is ok. -> Check power cord, unit fuses (BC150 only, BC,10, BC20, BC40 and BC80 has no user

serviceable fuses) and power switch.

- No power in outlet. -> Check house fuse box.

• There is no sound from the amp with LEDs Lit.

- Check amp gain and/or volume controls, check guitar controls. If controls are ok and all set above zero then listen

for hum in the speaker.

- There is no hum in the speaker. -> Internal speaker or power amp may need serviced.

- There is small hum in the speaker. -> Unplug guitar, touch tip of cable and listen.

- Hum is now very loud. -> Check your guitar electronics or try different guitar.

- Hum does not change. -> Replace your guitar cable.

• Sound quality is poor.

- Replace your guitar cable. If this does not help then check your speaker and speaker cable.

If the problem is not covered by the above or if our solutions does not help then please contact Warwick service information.

Headquarters: Warwick GmbH & Co. Music Equipment KG • Gewerbepark 46 • 08258 Markneukirchen / Germany • E-Mail: [email protected]

Branch China: Warwick Music Equipment (Shanghai) Ltd., Co.• Zhao Jia Bang Road No 108, 3rd Floor • 200020 Lu Wan District/Shanghai/P.R.China • E-Mail: [email protected]

Branch Switzerland: Warwick Music Equipment Trading (Zurich) GmbH • Kriesbachstrasse 30 • 8600 Dübendorf / Switzerland • E-Mail: [email protected]

Branch CZ/SK: Warwick Music Equipment Trading (Praha CZ) s.r.o. • Spálená 23/93 • 11000 Praha 1 / Czech Republic • E-Mail: [email protected]

Branch Poland: Warwick Music Equipment Trading (Warsaw) Sp. z o.o. • Flory 7/18a • 00-586 Warsaw / Poland • E-Mail: [email protected]

Branch UK/ Ireland: Warwick Music Equipment Trading (Hailsham UK) Ltd. • “Cortlandt” George Street • East Sussex BN27 1AE / Great Britain • E-Mail: [email protected]