Indesit IWC 6105 (EU).C instrukcja

Marka: Indesit

Model: IWC 6105 (EU).C

Kategoria: Pralki

Typ: instrukcja

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 4-5

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 6

Table of wash cycles

Personalisation, 7

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 8

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 9

General safety

Disposal

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

IWC 6105

Instructions for use

WASHING MACHINE

English,1

Español,13

Polski,25

Português,37

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washing machine is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so that

the new owner is able to familiarise himself/herself

with its operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a ¾

gas threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washing machine

by screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Technical data

Model

IWC 6105

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 6 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme 2; temperature 60°C;

using a load of 6 kg.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washing machine. If this is not the case, replace

the socket or the plug.

 The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

 When the washing machine has been installed, the

electricity socket must be within easy reach.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the washing machine on

and off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

SPIN SPEED knob: sets the spin speed or exclude

the spin cycle completely (see Personalisation).

WASH CYCLE PROGRESS/DELAY TIMER

indicator light

s: used to monitor the progress of the

wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time

remaining until the wash cycle starts will be indicated

(see next page).

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after about 30

minutes if no activity is detected. Press the ON-OFF

button briefly and wait for the machine to start up

again.

Description of the washing machine

and starting a wash cycle

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

SPIN SPEED

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see

Personalisation), after the wash cycle has been

started the indicator light corresponding to the

selected delay period will begin to flash:

As time passes, the remaining delay will be displayed

and the corresponding indicator light will flash:

The set programme will start once the selected time

delay has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the

indicator light corresponding to the first function

selected will flash and only the second function will be

activated; the indicator light corresponding to the

enabled option will remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is

locked to prevent it from being opened; make sure

the indicator light is off before opening the door (wait

approximately 3 minutes). To open the door during a

running wash cycle, press the START/PAUSE button;

the door may be opened once the DOOR LOCKED

indicator light turns off.

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the spin speed (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The door can be opened once the DOOR

LOCKED

indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the

drum dries completely. Switch the washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

Specials wash cycles

Express (wash cycle 10) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes

and therefore saves both energy and time. By selecting this wash cycle (10 at 30°C), it is possible to wash different

fabrics together (except for wool and silk items), with a maximum load of 1.5 kg.

Sport Intensive (

wash cycle

11) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.);

for best results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles".

Sport Light (

wash cycle

12) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for

best results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We

recommend using a liquid detergent and dosage suitable for a half-load.

Sport Shoes (

wash cycle

13) is for washing sports shoes; for best results, do not wash more than 2 pairs

simultaneously.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load

(kg)

Cycle

duration

Pre-

wash

Wash Bleach

Fabric

softener

Normal

Eco

Time

Normal

Eco

Time

Daily

Cotton with prewash:

extremely soiled whites.

90° 1000

164

Cotton:

extremely soiled whites.

90° 1000

ll l

145

Cotton (1):

heavily soiled whites and resistant colours.

60° 1000

ll l

185

Cotton (2):

heavily soiled whites and delicate colours.

40° 1000

ll l

123

Cotton:

heavily soiled whites and resistant colours.

60° 1000

ll l

63,5119102

Coloured Cottons (3):

lightly soiled whites and delicate colours.

40° 1000

ll l

6 3,5 89 78

Synthetics:

heavily soiled resistant colours.

60° 800

ll l

2,5 2 85 74

Synthetics:

lightly soiled delicate colours.

40° 800

ll l

2,5 2 70 60

Special

Wool:

for wool, cashmere, etc.

40° 600

1,5

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0

Jeans

40° 800

Express:

to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800

1,5

Sport

Sport Intensive

30° 600

Sport Light

30° 600

Sport Shoes

30° 600

Max. 2

pairs

Partial wash cycles

Rinse

1000

- -

Spin

1000

- - - -

Drain

- - - -

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash

The washing machine will automatically prevent you from selecting a temperature which is higher than the

maximum value set for each wash cycle.

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1000 rpm

Synthetics 800 rpm

Wool 600 rpm

Silk drain only

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol

The washing machine will automatically prevent you from selecting a spin speed which is higher than the

maximum speed set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of

lightly soiled cotton and synthetic fabrics (refer to the

"Table of wash cycles"

).   enables you to wash in less

time thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load

quantity.

 This function may not be used in conjunction with wash cycles 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Stain removal

Bleaching cycle designed to remove the toughest stains. Please remember to pour the bleach into extra

compartment 4 (see Bleach cycle).

 This function may not be used in conjunction with wash cycles 1, 7, 8, 9, 10, 11, 12, 13, , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is

particularly useful for sensitive skin.

 This function may not be used in conjunction with wash cycles 10, , .

Delay timer

This timer delays the start time of the wash cycle by up to 12 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time

the button is pressed, the function will be disabled.

N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching

the set programme.

 This option is enabled with all programmes.

Personalisation

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

ompartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Bleach cycle

 Traditional bleach should be used on sturdy white

fabrics, and delicate bleach for coloured fabrics,

synthetics and for wool.

This option is particularly

useful for the removal of

stubborn stains. Place

extra compartment 4

(supplied) into

compartment 1.

When pouring in the

bleach, be careful not to

exceed the "max" level

marked on the central

pivot (see figure).

To run the bleach cycle on its own, pour the bleach into

extra compartment 4, set the "Rinse"

programme

and activate the "Stain removal"

option.

To bleach during a wash cycle, pour in the detergent

and any fabric softener you wish to use, set the desired

wash cycle and enable the "Stain removal"

option.

The use of extra compartment 4 excludes the Pre-

wash option.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 6 kg

Synthetic fabrics: max. 2,5 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using

programme 7, even those carrying the "hand-wash

only"

label. For best results, use special

detergents and do not exceed 1,5 kg of laundry.

Silk: use special wash cycle 8 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 8.

Jeans: Turn garments inside-out before washing and

use a liquid detergent. Use programme 9.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washing machine

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Precautions and tips

 This washing machine was designed and

constructed in accordance with international safety

regulations. The following information is provided for

safety reasons and must therefore be read carefully.

General safety

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety. Children should be supervised

to ensure that they do not play with the appliance.

 This appliance was designed for domestic use only.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washing machine and help to prevent leaks.

 Unplug the washing machine when cleaning it and

during all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine

(see figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),

make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light

for the first wash cycle stage

flashes rapidly).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The "option" indicator lights and

the "start/pause" indicator light

flash, while one of the "phase in

progress" indicator lights and the

"door locked" indicator light will

remain lit in a fixed manner.

There is too much foam.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washing machine door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see Personalisation).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washing machine to fill with water

and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require

the drain phase to be started manually.

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washing machine is not level (see Installation).

 The washing machine is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see

Care and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also

be found on the front of the appliance by opening the door.

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Descripción de la lavadora y comienzo

de un programa, 16-17

Panel de control

Pilotos

Poner en marcha un programa

Programas, 18

Tabla de programas

Personalizaciones, 19

Seleccionar la temperatura

Seleccionar el centrifugado

Funciones

Detergentes y ropa, 20

Contenedor de detergentes

Ciclo de blanqueo

Preparar la ropa

Prendas especiales

Sistema de equilibrado de la carga

Precauciones y consejos, 21

Seguridad general

Eliminaciones

Mantenimiento y cuidados, 22

Interrumpir el agua y la corriente eléctrica

Limpiar la lavadora

Limpiar el contenedor de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Anomalías y soluciones, 23

Asistencia, 24

IWC 6105

Manual de instrucciones

LAVADORA

Instalación

 Es importante conservar este manual para poder

consultarlo en cualquier momento. En caso de venta,

de cesión o de traslado, verifique que permanezca

junto con la lavadora para informar al nuevo

propietario sobre el funcionamiento y brindar las

correspondientes advertencias.

 Lea atentamente las instrucciones: ellas contienen

importante información sobre la instalación, el uso y la

seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufrido daños

durante el transporte. Si estuviera dañada no la

conecte y llame al revendedor.

3. Quite los 4 tornillos de

protección para el

transporte y la arandela

de goma con el

correspondiente

distanciador ubicados en

la parte posterior (ver la

figura).

4. Cubra los orificios con los tapones de plástico

suministrados con el aparato.

5. Conserve todas las piezas: cuando la lavadora

deba ser transportada nuevamente, deberán volver a

colocarse.

 Los embalajes no son juguetes para los niños.

Nivelación

1. Instale la lavadora sobre un piso plano y rígido, sin

apoyarla en las paredes, muebles ni en ningún otro

aparato.

2. Si el piso no está

perfectamente horizontal,

compense las

irregularidades

desenroscando o

enroscando las patas

delanteras (ver la figura);

el ángulo de inclinación

medido sobre la superfi-

cie de trabajo, no debe

superar los 2º.

Una cuidadosa nivelación brinda estabilidad a la

máquina y evita vibraciones, ruidos y desplazamientos

durante el funcionamiento. Cuando se instala sobre

moquetas o alfombras, regule los pies para conservar

debajo de la lavadora un espacio suficiente para la

ventilación.

Conexiones hidráulicas y eléctricas

Conexión del tubo de alimentación de agua

1. Conectar el tubo de

tubo enroscándolo a un

grifo de agua fría con la

boca roscada de 3/4 gas

(ver la figura).

Antes de conectarlo,

haga correr el agua hasta

que esté límpida.

2. Conecte el tubo de

alimentación a la

lavadora enroscándolo en

la toma de agua

correspondiente ubicada

en la parte posterior

derecha (arriba) (ver la

figura).

3. Controle que en el tubo no hayan pliegues ni

estrangulaciones.

 La presión de agua del grifo debe estar

comprendida dentro de los valores contenidos en la

tabla de Datos técnicos (ver la página

correspondiente).

 Si la longitud del tubo de alimentación no es la

suficiente, diríjase a un negocio especializado o a un

técnico autorizado.

 No utilice nunca tubos ya usados.

 Utilice los suministrados con la máquina.

65 - 100 cm

Conexión del tubo de descarga

Conecte el tubo de

descarga, sin plegarlo, a

una tubería de descarga

o a una descarga de

pared colocadas a una

altura del piso entre 65 y

100 cm;

o apóyelo en el borde de

un lavamanos o de una

bañera, uniendo la guía

suministrada con el

aparato, al grifo (ver la

figura). El extremo libre

del tubo de descarga no

debe permanecer

sumergido en el agua.

 No se aconseja utilizar tubos de prolongación, si

fuera indispensable hacerlo, la prolongación debe

tener el mismo diámetro del tubo original y no superar

los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

 la toma tenga la conexión a tierra y haya sido

hecha según las normas legales;

 la toma sea capaz de soportar la carga máxima de

potencia de la máquina indicada en la tabla de

Datos técnicos (ver al costado);

 la tensión de alimentación esté comprendida dentro

de los valores indicados en la tabla de Datos

técnicos (ver al costado);

 la toma sea compatible con el enchufe de la

lavadora. Si no es así, sustituya la toma o el

enchufe.

 La lavadora no debe ser instalada al aire libre, ni

siquiera si el lugar está reparado, ya que es muy

peligroso dejarla expuesta a la lluvia o a las

tormentas.

 Una vez instalada la lavadora, la toma de corriente

debe ser fácilmente accesible.

 No utilice prolongaciones ni conexiones múltiples.

 El cable no debe estar plegado ni sufrir

compresiones.

 El cable de alimentación debe ser sustituido sólo

por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas no

sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso, realice un

ciclo de lavado con detergente y sin ropa,

seleccionando el programa 2.

Datos técnicos

Modelo

IWC 6105

Dimensiones

ancho 59,5 cm.

altura 85 cm.

profundidad 53,5 cm.

Capacidad

de 1 a 6 kg.

Conexiones

eléctricas

ver la placa de características

técnicas aplicada en la máquina

Conexiones

hídricas

presión máxima 1 MPa (10 bar)

presión mínima 0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad de

centrifugado

máxima 1000 r.p.m.

Programas de

control según la

norma EN 60456

programa 2; temperatura 60ºC;

efectuado con 6 kg. de carga.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 89/336/CEE del 03/05/89

(Compatibilidad Electromagnética) y

sucesivas modificaciones

- 2002/96/CE

- 2006/95/CE (Baja Tensión)

Contenedor de detergentes: para cargar

detergentes y aditivos (ver Detergentes y ropa).

Botón de ENCENDIDO/APAGADO: para encender

y apagar la lavadora.

Mando de PROGRAMAS: para elegir los programas.

Durante el funcionamiento del programa el mando no

se mueve.

Botones con pilotos de FUNCIÓN: para seleccionar

las funciones disponibles. El piloto correspondiente a

la función seleccionada permanecerá encendido.

Mando de CENTRIFUGADO: para seleccionar el

centrifugado o excluirlo (ver Personalizaciones).

Mando de TEMPERATURA: para seleccionar la

temperatura o el lavado en frío (ver

Personalizaciones).

Pilotos DE AVANCE DEL CICLO/COMIENZO

RETRASADO: para seguir el estado de avance del

programa de lavado.

El piloto encendido indica la fase en curso.

Si se seleccionó la función Comienzo retrasado,

indicarán el tiempo que falta para la puesta en

marcha del programa (ver la página correspondiente).

Piloto PUERTA BLOQUEADA: para saber si la

puerta se puede abrir (ver la página correspondiente).

Botón con piloto PUESTA EN MARCHA/PAUSA: se

utiliza para poner en marcha los programas o

interrumpirlos momentáneamente.

Nota: Presione este botón para poner en pausa el

lavado en curso, el piloto correspondiente centelleará

con color anaranjado mientras que el de la fase en

curso permanecerá encendido en forma fija. Si el

piloto PUERTA BLOQUEADA

está apagado, se

podrá abrir la puerta.

Para que el lavado se reanude a partir del momento

en el cual fue interrumpido, presione nuevamente

este botón.

Modalidad de stand by

Esta lavadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está

dotada de un sistema de auto-apagado (stand by)

que, en caso de no funcionamiento, se activa

pasados aproximadamente 30 minutos. Presionar

brevemente el botón ON-OFF y esperar que la

máquina se active.

Descripción de la lavadora y

comienzo de un programa

Piloto

PUERTA

BLOQUEADA

Botón con piloto

PUESTA EN

MARCHA/

PAUSA

Panel de control

Contenedor de detergentes

Botón de

ENCENDIDO/

APAGADO

Mando de

PROGRAMAS

Botones con pilotos

FUNCIÓN

Mando de

TEMPERATURA

Mando de

CENTRIFUGADO

Pilotos

DE AVANCE DEL

CICLO/COMIENZO

RETRASADO

Pilotos

Los pilotos suministran información importante.

He aquí lo que nos dicen:

Comienzo retrasado

Si se ha activado la función Comienzo retrasado (ver

Personalizaciones), después de haber puesto en

marcha el programa, comenzará a centellear el piloto

correspondiente al retraso seleccionado:

Con el transcurrir del tiempo se visualizará el retraso

residual con el centelleo de la luz testigo

correspondiente:

Una vez transcurrido el tiempo de retraso

seleccionado, comenzará el programa.

Pilotos fase en curso

Una vez seleccionado y puesto en marcha el ciclo de

lavado deseado, las luces testigo se encenderán

progresivamente para indicar su estado de avance:

Botones de función y pilotos correspondientes

Seleccionando una función, el piloto correspondiente

se iluminará. Si la función seleccionada no es

compatible con el programa elegido, el piloto

correspondiente centelleará y la función no se

activará. Si la función elegida no es compatible con

otra seleccionada precedentemente, el piloto

correspondiente a la primera función seleccionada

centelleará y se activará sólo la segunda, el piloto de

la función activada se iluminará.

Piloto puerta bloqueada

El piloto encendido indica que la puerta está

bloqueada impidiendo su apertura; para poder abrir la

puerta es necesario que dicho piloto esté apagado

(espere 3 minutos aproximadamente). Para abrir la

puerta mientras un ciclo está en curso, presione el

botón PUESTA EN MARCHA/PAUSA; si el piloto

PUERTA BLOQUEADA está apagado, será posible

abrir la puerta.

Poner en marcha un programa

1. Encienda la lavadora presionando el botón ENCENDIDO/APAGADO. Todos los pilotos se encenderán durante

algunos segundos, luego se apagarán y se deberá pulsar el piloto PUESTA EN MARCHA/PAUSA.

2. Cargue la ropa y cierre la puerta.

3. Seleccione el programa deseado con el mando de PROGRAMAS.

4. Fije la temperatura de lavado (ver Personalizaciones).

5. Fije la velocidad de centrifugado (ver Personalizaciones).

6. Vierta detergente y aditivos (ver Detergentes y ropa).

7. Seleccione las funciones deseadas.

8. Ponga en marcha el programa presionando el botón PUESTA EN MARCHA/PAUSA y el piloto correspondiente

permanecerá encendido, fijo y de color verde. Para anular el ciclo seleccionado ponga en pausa la máquina

presionando el botón PUESTA EN MARCHA/PAUSA y elija un nuevo ciclo.

9. Al final del programa se iluminará el piloto

. Cuando el piloto PUERTA BLOQUEADA se apague, será

posible abrir la puerta. Extraiga la ropa y deje la puerta semicerrada para permitir que el cesto se seque.

Apague la lavadora presionando el botón ENCENDIDO/APAGADO.

Lavado

Aclarado

Centrifugado

Descarga

Fin del Lavado

Descripción del Programa

Te m p .

max.

(°C)

Velocid-

ad máx.

(r.p.m.)

Detergentes

Carga máx.

(Kg.)

Duración

del ciclo

Prela-

Lava

Blanque-

ador

Suavi-

zante

Nor-

mal

Eco

Time

Nor-

mal

Eco

Time

Diario (programas para todos los días)

Prelavado Algodón:

blancos sumamente sucios.

90° 1000

164

Algodón:

blancos sumamente sucios.

90° 1000 -

lll

145

Algodón (1):

blancos y colores resistentes muy sucios.

60° 1000 -

lll

185

Algodón (2):

blancos y colores delicados muy sucios.

40° 1000 -

lll

123

Algodón:

blancos sumamente sucios.

60° 1000 -

lll

63,5119102

Algodón de color (3):

blancos poco sucios y colores delicados.

40° 1000 -

lll

6 3,5 89 78

Sintético:

colores resistentes muy sucios.

60° 800 -

lll

2,5 2 85 74

Sintético:

colores delicados poco sucios.

40° 800 -

lll

2,5 2 70 60

Programas Especiales

Lana:

para lana, cachemira, etc.

40° 600 -

1,5

Seda/Cortinas:

para prendas de seda, viscosa, lencería.

30° 0 -

Jeans

40° 800 -

Express:

para refrescar rápidamente prendas poco sucias (no se

aconseja utilizarlo para lana, seda y prendas para lavar a mano).

30° 800 -

1,5

Sport

Sport Intensive

30° 600 -

3 - 78 -

Sport Light

30° 600 -

3 - 68 -

Sport Shoes

30° 600 -

Max.2

pares

-50-

Programas Parciales

Aclarado - 1000 - -

Centrifugado - 1000 - - - - 6

Descarga - 0 - - - - 6

Programas particulares

Express (programa 10) fue estudiado para lavar prendas ligeramente sucias y en poco tiempo: dura sólo 15

minutos y de esa manera permite ahorrar energía y tiempo. Seleccionando el programa (10 a 30ºC) es posible

lavar conjuntamente tejidos de distinto tipo (excluidas lana y seda), con una carga máxima de 1,5 kg.

Sport Intensive (programa 11) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales,

pantalones cortos, etc.) muy sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima

indicada en la "Tabla de programas".

Sport Light (programa 12) ha sido estudiado para lavar tejidos usados en prendas deportivas (chándales, pantalones

cortos, etc.) poco sucios; para obtener los mejores resultados es aconsejable no superar la carga máxima indicada

en la "Tabla de programas". Se recomienda utilizar detergente líquido y la dosis correspondiente a la media carga.

Sport Shoes (programa 13) ha sido estudiado para lavar calzado deportivo; para obtener los mejores resultados

no lave más de 2 pares a la vez.

Programas

Los datos contenidos en la tabla tienen un valor indicativo.

Para todos los Test Institutes:

1) Programa de control según la norma EN 60456: seleccione el programa 2 con una temperatura de 60ºC.

2) Programa algodón largo: seleccione el programa 2 con una temperatura de 40ºC.

3) Programa algodón corto: seleccione el programa 4 con una temperatura de 40ºC.

Programas

Tabla de programas

Seleccionar la temperatura

Girando el mando de la TEMPERATURA se selecciona la temperatura de lavado (ver la Tabla de programas).

La temperatura se puede disminuir hasta el lavado en frío (

La máquina impedirá automáticamente seleccionar una temperatura mayor que la máxima prevista para cada

programa.

Seleccionar el centrifugado

Girando el mando de CENTRIFUGADO se selecciona la velocidad de centrifugado del programa seleccionado.

Las velocidades máximas previstas para los programas son:

Programas Velocidad máxima

Algodón 1000 r.p.m.

Sintéticos 800 r.p.m.

Lana 600 r.p.m.

Seda sólo descarga

Se puede disminuir la velocidad de centrifugado o excluirlo seleccionando el símbolo

La máquina impedirá automáticamente efectuar un centrifugado a una velocidad mayor que la máxima prevista

para cada programa.

Funciones

Las distintas funciones de lavado previstas por la lavadora permiten obtener la limpieza y el blanco deseados.

Para activar las funciones:

1. presione el botón correspondiente a la función deseada;

2. el encendido del piloto correspondiente indica que la función está activa.

Nota: El centelleo rápido del piloto indica que la función correspondiente no se puede seleccionar para el

programa elegido.

Seleccionando esta opción, se optimizan el movimiento mecánico, la temperatura y el agua para una carga

reducida de prendas de algodón y sintéticas poco sucias (ver la "Tabla de programas").

Con   se puede lavar en un tiempo menor, ahorrando agua y energía. Se aconseja utilizar una dosis de

detergente líquido adecuada a la cantidad de carga.

 No se puede activar con los programas 1, 2, 7, 8, 9, 10, 11, 12, 13, , , .

Antimancha

Ciclo de blanqueo adecuado para eliminar las manchas más resistentes. Recuerde verter el blanqueador en la

cubeta adicional 4 (ver Ciclo de blanqueo).

 No se puede activar con los programas 1, 7, 8, 9, 10, 11, 12, 13, , .

Aclarado extra

Al elegir esta función aumentará la eficacia del aclarado y se asegurará la máxima eliminación del detergente. Es

útil para pieles particularmente sensibles.

 No se puede activar con los programas 10, , .

Comienzo retrasado

Retrasa la puesta en marcha de la máquina hasta 12 horas.

Presione varias veces el botón hasta hacer encender la luz testigo correspondiente al retraso deseado. La quinta vez

que se presione el botón, la función se desactivará.

Nota: Una vez presionado el botón PUESTA EN MARCHA/PAUSA, se puede modificar el valor del retraso sólo

disminuyéndolo hasta que se ponga en marcha el programa seleccionado.

 Se puede utilizar en todos los programas.

Personalizaciones

Detergentes y ropa

Contenedor de detergentes

El buen resultado del lavado depende también de la

correcta dosificación del detergente: si se excede la

cantidad, no se lava de manera más eficaz, sino que

se contribuye a encostrar las partes internas de la

lavadora y a contaminar el medio ambiente.

 No use detergentes para el lavado a mano porque

producen demasiada espuma.

Extraiga el contenedor de

detergentes e introduzca

el detergente o el aditivo

de la siguiente manera:

cubeta 1: Detergente para prelavado (en polvo)

Antes de verter el detergente, verifique que no esté

colocada la cubeta adicional 4.

cubeta 2: Detergente para lavado (en polvo o

líquido)

El detergente líquido se debe verter sólo antes de la

puesta en marcha.

cubeta 3: Aditivos (suavizante, etc.)

El suavizante no se debe volcar fuera de la rejilla.

cubeta adicional 4: Blanqueador

Ciclo de blanqueo

 El blanqueador tradicional debe utilizarse para los

tejidos resistentes blancos, mientras que el delicado

debe utilizarse para la lana y los tejidos coloreados y

sintéticos.

Introduzca la cubeta

adicional 4 suministrada

con el aparato, en la

cubeta 1.

Al verter el blanqueador

no debe superar el nivel

"máx." indicado en el

perno central (véase la

figura).

Para realizar sólo el

blanqueo, vierta el blanqueador en la cubeta adicional

4, seleccione el programa Aclarado

y active la

función Antimancha

Para blanquear durante el lavado, vierta el detergente

y los aditivos, seleccione el programa deseado y active

la función Antimancha

El uso de la cubeta adicional 4 excluye el prelavado.

Preparar la ropa

 Subdivida la ropa según:

- el tipo de tejido / el símbolo en la etiqueta.

- los colores: separe las prendas de color y las

blancas.

 Vacíe los bolsillos y controle los botones.

 No supere los valores indicados, referidos al peso

de la ropa seca:

Tejidos resistentes: max 6 kg.

Tejidos sintéticos: max 2,5 kg.

Tejidos delicados: max 2 kg.

Lana: max 1,5 kg.

Seda: max 1 kg.

¿Cuánto pesa la ropa?

1 sábana 400/500 g

1 funda 150/200 g

1 mantel 400/500 g

1 albornoz 900/1200 g

1 toalla 150/250 g

Prendas especiales

Lana: con el programa 7 es posible lavar en la

lavadora todas las prendas de lana, aún las que

contienen la etiqueta "sólo lavado a mano"

Para

obtener los mejores resultados utilice un detergente

específico y no supere 1,5 Kg. de ropa.

Seda: utilice el programa correspondiente 8 para

lavar todas las prendas de seda. Se aconseja el uso

de un detergente específico para prendas delicadas.

Cortinas: pliéguelas y colóquelas dentro de una

funda o de una bolsa de red. Utilice el programa 8.

Jeans: vuelva del revés las prendas antes del lavado

y utilice un detergente líquido. Utilice el programa 9.

Sistema de equilibrado de la carga

Antes de cada centrifugado, para evitar vibraciones

excesivas y para distribuir la carga de modo uniforme,

el cesto realiza rotaciones a una velocidad

ligeramente superior a la del lavado. Si después de

varios intentos, la carga todavía no está

correctamente equilibrada, la máquina realiza el

centrifugado a una velocidad inferior a la prevista.

Cuando existe un excesivo desequilibrio, la lavadora

realiza la distribución antes que el centrifugado. Para

obtener una mejor distribución de la carga y su

correcto equilibrado, se aconseja mezclar prendas

grandes y pequeñas.

Strona jest ładowana ...

Indesit IWC 6105 (EU).C instrukcja

Marka: Indesit

Model: IWC 6105 (EU).C

Kategoria: Pralki

Typ: instrukcja

ściągnij PDF

raport

w innych językach

español: Indesit IWC 6105 (EU).C Guía del usuario
português: Indesit IWC 6105 (EU).C Guia de usuario
English: Indesit IWC 6105 (EU).C User guide

Indesit IWC 6105 (EU).C instrukcja

Indesit IWC 6105 (EU).C instrukcja

w innych językach

Inne dokumenty