- 2 -
Contents
For the user
Safety information 3
– Installation and servicing
– Child safety
– During use
– At the end of the dryer’s life
Description of the appliance 4-5
Using your appliance 6
– Before you use the dryer for the first time
– Capacity
– Examples of laundry item weights
General information 7
Program chart 8
– Consumption
The indicator lights 9
Maintenance 10-11
– The filters
– The condenser
– Emptying the water tank
If the machine is not working 12
Service 13
– Service and spare parts
For the installer
Technical data 13
Unpacking the machine 14
– Damages
– Accessories supplied
– Optional extra accessories
– Identification of materials
Installation 15-16
– Positioning
– Electrical supply
– Wall mounting
Rukowodstwo po \kspluatacii 17
- 3-
Safety information
822 61 13-62
Before installing and first using the tumble dryer, read this instruction booklet carefully, including
i
ts hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure
that all people using the dryer are thoroughly familiar with its operation and safety features.
S
ave these instructions and make sure they remain with the tumble dryer if it is moved or sold, so
that everyone using it through its life can be properly informed on appliance use and safety.
Installation and servicing
● A
ll installation and service work done on the product
must be carried out by a qualified technician. Work
performed by persons with inadequate knowledge may
adversely affect the satisfactory functioning of the
product and may cause personal injury or damage.
Before any work is carried out on the tumble dryer, it
must be isolated from the electrical supply. To do this
the power plug must be removed from the wall socket.
● The machine is heavy, so take care when moving it.
● If the dryer is installed in a bathroom without fixed
wiring to the electrical supply, an earth leakage circuit
breaker (or RCD) must be used.
● The power cable must be plugged into an earthed
socket, which must be easily accessible. Permanent
installation must only be carried out by an authorized
electrician.
● If the power cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
● Make sure that the power cable is not nipped or other-
wise damaged when moving the machine in connection
with installation or cleaning etc.
● The ventilation opening at the bottom of the door should
not be obstructed if the dryer is on a carpeted floor.
● The adjustable feet must not be removed, these
ensure that the underside of the dryer is ventilated.
● Servicing and repairs must be carried out by a service
company authorised by the supplier. Use only spare
parts supplied by these. Never try to repair the machine
yourself.
Child safety
● The tumble dryer should be used by adults only. Do not
let children play with the controls or other parts of it.
● Keep all packaging well away from children.
● Before loading the machine, check that there are no
foreign objects or pets inside the drum.
During use
● T
his dryer is intended only for normal domestic drying of
laundry and only in accordance with these instructions.
Using it for other purposes could lead to physical injury
or damage to property and invalidate the guarantee.
● Do not overload the dryer (see “Using your appliance”).
● Never start the dryer unless the fluff filter is clean and
correctly in place, or if the fluff filter is damaged (this
could cause overheating or damage your laundry).
● Get into the habit of cleaning the condenser at regular
intervals. Keeping the condenser as clean as possible
makes the dryer more efficient and means shorter
drying times.
● Laundry which has been in contact with chemicals such
as dry cleaning fluid and similar, should not be dried in
the machine, since volatile chemicals can be a fire risk.
● The following items/materials should not be dried in
the machine either:
– Pillows, cushions, down-filled items etc. (these
cause a build-up of heat and can make the dryer
overheat)
– Wool, on account of its tendency to mat
– Especially sensitive textiles, such as synthetic
curtains, silk etc.
– Garments made of foam rubber or rubber-like
materials must not be dried in the machine.
● Always switch off and unplug the appliance after use.
When removing the electrical plug, grip the plug, not
the lead.
At the end of the dryer’s life
The symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product,
please contact your local city office, your household waste
disposal service or the shop where you purchased the
product.
- 4 -
Description of the appliance
1. Door Latch (push the knob to the right to open)
Avoid opening the door while a program is in
progress.
2. Space for programme chart
(Self-adhesive label)
3. Control panel
4. Warm air discharge
5. Air ducts
- These should not be obstructed.
6. Condenser
This is built into the door and needs to be cleaned
at regular intervals.
7. Filters
Should be cleaned before or after each load. The
fluff filter is behind the coarse filter and can be
removed for cleaning.
8. Adjustable feet
If the dryer is not being wall mounted the feet need
to be adjusted so that the dryer is level.
9. Rating plate
10. Drum
11. Electrical lead
12. Holder for wall mounting console
9
10
14
6
7
5
8
4
3
2
2
1
- 5 -
Description of the appliance
13. Connector for drain hose
There is a drain hose as an extra accessory for you
who want and can connect the tumble dryer directly
t
o a drain outlet. Fix the hose to the connector (13)
after releasing the hose clip and removing the plug.
When a drain hose is fitted, the water tank will not
be filled with water.
14. Water tank for condensed water
This fills up with the water condensed by the dryer
and should be emptied after each load. When the
tank is full, a warning light (D) will flashing and a
buzzer will sound. The dryer will stop automatically
and will not restart until the tank has been emptied.
If the dryer should stop on account of a full tank
during an automatic program and you fail to empty
the tank within 5 minutes, the program may not be
able to continue successfully. If this happens, the
current program will need to be cancelled and a
new one started. For this reason it is best always
to check that the tank is empty before starting to
dry a new load.
• Lights (see also chapter ”The indicator lights”).
A. Lit during drying stage.
B. Lit during cool-down stage.
C. Flash alternately during anticrease stage.
D. Flashes when water tank is full.
• Buttons
E. Start button. After selecting program, press and
hold the start button intil one of the indicator
lights comes on (1-2 seconds).
F
.
Button for reduced heat for timed programs.
If this button is pressed, the drying heat will be
reduced and the load will dry at a lower temperature.
Suitable for especially delicate textiles.
• Program selector
G. For selecting electronic or timed drying programs
(see also chapter ”Program chart”).
• Cancel program
H. If the program selector is turned to this position
during a program, the program will be cancelled
and a different program can then be selected.
To start the new program, press the start button.
12
11 13
A
D
G
E
B
F
C
H
3
- 6-
Before using the dryer for the first time
Dampen some clean pieces of unwanted cloth and dry
them for about 15 minutes the very first time, to make
s
ure that there is no dust or dirt in the dryer.
1
. Check that the dryer is connected to the electrical
supply.
2. Open the door by pushing the knob to the right (A).
3. Check that the fluff filter (B) is clean and that the
coarse filter (C) is lowered and has snapped into
place.
4. Check that the water tank (D) is empty and pushed
correctly into place.
5. Put the load for drying into the machine. Make sure
that it is right inside the drum. Do not mix synthetics
with natural materials.
6. Close the door.
7. Use the Program selector (E) to select the type of
drying program required, either automatic or timed.
8. Press the start button (F) inwards.
It is advisable not to open the door during a
programme as this could cause water to leak
from the machine.
Capacity (dry items)
Cotton max. 3,4 kg
Synthetics max. 1,5 kg
Examples of laundry item weights
(dry items)
To help you load your tumble dryer correctly, here are
s
ome examples of average garment or item weights.
These are based on cotton goods.
Bathrobe ~1.2 kg
Duvet cover ~0.7 kg
Sheet ~0.5 kg
Blouse ~0.1 kg
Towel (Terry) ~0.2 kg
Shirt ~0.2 kg
Nightdress ~0.2 kg
Pyjamas ~0.2 kg
Underpants ~0.1 kg
Underpants (long) ~0.3 kg
Pillow-case ~0.2 kg
Socks ~0.1 kg
A
B
C
D
E
F
Using your appliance
- 7 -
General washing and drying information
Sorting
Always sort loads for drying according to the type of fabric
(check the care labels) and how much you want to dry them.
Load items loosely into the drum. Do up zip fasteners and
tie loose ribbons, tapes or fabric belts. Close any tapes
or fasteners on duvet covers and pillow cases to prevent
smaller items from getting trapped inside.
Spinning (water extraction)
Loads should be well spun. We recommend that you use
a washing machine with a minimum spin speed of 800
rpm, or a separate spin-dryer (“Hydro-extractor”) if
available. The higher the spin speed, the faster your
tumble dryer will dry the load and the more energy-
efficient the whole process will be.
Even permanent press garments such as shirts should
be spun for 10 to 30 seconds before tumble drying.
Getting the load size right
An overloaded tumble dryer will cause creasing. Drying
loads which are too small is uneconomical.
Fluff
The first time you use the tumble dryer, you will probably
be surprised at the amount of fluff produced. This is
perfectly normal, and does not mean that your tumble
dryer is wearing out your clothes. When garments are
worn and washed by hand or machine, fibres and fluff
are released, but remain on the surface of the material.
If dried outdoors on a line these fibres will be blown away
by the wind. In a tumble dryer the fluff is collected in the
filter and accumulates through the drying process. This
is very significant to those who suffer from asthma or
allergies.
Shrinkage
Depending on their quality, tricot fabrics in particular vary
considerably in their tendency to shrink. To avoid
shrinking, garments should not be overdried. Where it
occurs,
shrinkage can sometimes be rectified by
stretching. We recommend that you bear possible
shrinkage in mind when choosing the size of new tricot
garments.
Starched items
Laundry which has been starched can also be dried in a
tumble dryer. For best results you should choose a
drying time which ensures that the items are still slightly
damp, e.g. by following the recommendations to achieve
“damp dry (for ironing)”. After removing the load, wipe
the drum clean with a damp cloth. Then dry the drum to
r
emove any last traces of starch.
Items which should not be tumble dried
Items which are especially delicate, such as curtains of
synthetic fabric, woollen garments, silk, textiles with a
metal component, nylon socks/stockings. Garments made
mostly from foam rubber or rubber-like materials must
NOT be dried in the tumble dryer.
Obviously, you must not dry garments in the
machine which are unsuitable for tumble
drying. These are usually labelled with this
symbol.
Garments which have been treated with
flammable liquids (benzine, alcohol, stain
removal products) should not be dried in the
tumble dryer on account of the risk of fire.
Always follow the recommendations of the
garment/item manufacturer.
Tumble drying beneficial
Dry flat
- 8 -
Program chart
Type of dry laundry and
load weight
How dry? Program
Load weight,
kg
Spun at approx.
800 rpm
before drying
Cotton, max. 3,4 kg.
Non-delicate items.
Extra dry
A
3,4
2.0
1,0
105 - 120
80 - 90
55 - 65
Cotton, max. 3,4 kg.
Towelling (terry), tricot e.d.
Cupboard dry
B
3,4
2.0
1,0
95 - 110
70 - 80
50 - 60
Cotton, max. 3,4 kg.
Bed linen, towels e.d.
Iron dry
C
3,4
2.0
1,0
80 - 95
55 - 75
45 - 55
Synthetics, max 1,5 kg.
Automatic heat reduction.
Delicate items.
Cupboard dry
D
1,5
1,0
0,7
45 - 55
40 - 50
38 - 48
Timed drying
Cotton, max. 3,4 kg.
Depends on
time set
20 - 90
Timed drying.
Synthetics, max. 1,5 kg.
Reduce heat by pressing the
button in the control panel.
Depends on
time set
20 - 90
Cool-down program,
lasts 9 minutes.
The programs can be divided into two types: automatic programs and timed programs.
The automatic programs (A – D) switch off the tumble dryer when the load has been dried to the extent required.
The timed programs are for special requirements or finishing drying individual items. Using these, the dryer will
c
ontinue to dry through the time you have set, unless the load is dry before that time has elapsed. When the load is
dry the program switches automatically to a cool-down stage of 9 minutes. If the load is not removed from the dryer
a
t the end of the cool-down stage, an anti-crease stage of 30 minutes will then start automatically to keep the load in
motion, thereby preventing creasing.
Consumption according to the EN 61121 Europa standard
Energy 2,47 kWh/3,4 kg cotton
The consumer information on the energy declaration is in accordance with directive EEC 92/75
and refers to the 90 minutes timed programme.
- 9 -
The indicator lights
Drying stage in progress.
Cool-down stage in progress.
The indicator lights on the panel have three possible statuses: fixed light, flashing slowly and flashing rapidly.
The table below explains the meanings of the various lights or combinations of lights.
Fixed light
Flashing rapidly
Door open during drying stage.
Door open during cool-downg stage.
Anti-crease stage will run for 30 min.
The lights will go on flashing until the
door is opened.
Water tank full (buzzer).
Water tank full and door open.
Alarm, program selector is between two
programs. If not, call service.
* The door has been opened during
the drying stage and closed again.
* The door has been opened during
the cool-down stage and closed
again.
The water tank has been emptied.
* The door has been opened and
closed again.
●
●
●
●
●
●
( ● )
●
( ● )
●
●
in sequence
●
in sequence
●
in sequence
●
in sequence
( ● ) Depending on whether the dryer was in the drying or cool-down stage when the door was opened and whether
the water tank was full/was emptied.
* For the children safety, the dryer will not restart automatically while a program is still in progress if the door has
been opened and then closed again – the indicator light will flash rapidly. First make quite sure that the drum
contains nothing other than the load of laundry before restarting the dryer by pressing the start button.
Flashing slowly
●
alternately
( ● ) ( ● )
- 10 -
Maintenance
A
B
C
D
E
F
G
The filters
For your tumble dryer to function correctly, the filters need
to be cleaned before or after every load dried.
To clean them:
1. Open the door.
2
. Open the coarse filter upwards (Fig. A).
3
. Brush the fluff off the fluff filter, which is under the
coarse filter (Fig. B). Sometimes you may need to
remove the fluff filter to clean it on both sides.
Make sure that you put the fluff filter back correctly
after cleaning, before closing the coarse filter.
Never start the dryer unless the fluff filter
is clean and correctly in place, or if the
fluff filter is damaged (this could cause
overheating).
The condenser
As in all types of tumble dryer, the air circulated through the
dryer picks up fluff. As a result, some fluff will accumulate
in the condenser, so it needs to be cleaned occasionally.
To clean the condenser:
1. Open the door and open the coarse filter upwards.
2. Remove the fluff filter and close the coarse filter
again.
3. Grasp the recesses at the top of the condenser
with your fingers and use your thumbs to press
against the door (Fig. C & D).
The condenser will come free, allowing you to lift
it outwards/upwards. Be careful not to damage
the sensitive aluminium section.
4. Turn it upside down and clean it on both sides,
using a vacuum cleaner. Remove the red drain
plug on the lower
edge of the condenser (Fig E).
Lay the condenser flat and fill it with water through
the filter opening. Now leave the condenser to
soak in water for about 5 minutes, then shower
both sides with hot water. (Fig. F).
Dry the condenser carefully afterwards. Don’t
forget to put back the red drain plug (Fig. G).
5. Put the condenser back in the dryer. Make sure
that its base is lined up in the slots in the condenser
cavity inside the dryer door.
Press the condenser carefully into place until you
feel and hear a gentle
“snap”. Put back the fluff
filter and close the coarse filter.
- 11 -
Maintenance
A
B
Emptying the water tank
If you have connected the tumble dryer directly to a
w
aste pipe with the accessory hose, you can ignore
this section.
B
ut note that even if the water tank has been bypassed
in this way, the indicator light warning that the tank is
full will flash intermittently during the anti-crease stage.
The tank will not need emptying, but don’t forget to
clean the filters.
A warning light on the control panel will flashing and a
buzzer will sound when it is time to empty the water tank.
If it is operating when this happens, the dryer will stop
automatically and the tank will have to be emptied. It is
a good idea to get into the habit of emptying the tank
either before or after each load.
To empty the tank:
1. Open the door.
2. Pull out the tank (Fig. A).
3. Open the tank lid and pour the water out
(Fig. B).
4. Close the lid and push the tank back into
place. Press it home until you can feel that
it is properly in place.
- 12 -
If the machine is not working
Never attempt to repair the tumble dryer yourself.
Repairs carried out by unauthorised or inexperienced
persons can cause injury or serious malfunctioning.
● The dryer will not start. ● Is the door closed properly?
● Is there power to the machine?
● Has the fuse blown?
● Have you set the program selector properly?
● Is the water tank full?
● Is the Start button pressed in?
● The load is not drying properly, ● Was right program chosen? Check that the
or is taking too long to dry. Reduced heat button has not been pressed.
● Is the load too large?
Cotton max. 3,4 kg
Synthetics max. 1,5 kg
● Is the fluff filter clogged?
● Is the condenser clogged?
● Was the load not spun enough in the washing
machine?
● Has the door been opened while a program was
running?
● Is the temperature in the room too high?
Must not exceed +35° C.
● The area around the dryer is hot. ● Is the room too small?
(Improve the room ventilation, open a door or
window, or choose another site for the dryer.
● The indicator lights flash in ● Is the program selector between two program
sequence 1->2->3->4->1->2 etc. settings?
Turn the selector to the setting required.
If this does not help, call service.
● Fault ● Check
This appliance complies with the requirements of the following EU directives:
– 73/23/EEC, dated 19.02.1973 – low-voltage directive.
– 89/336/EEC, dated 03.05.1989 (incl. amendment
92/31/EEC) – directive on electromagnetic compatibility.
B
efore calling out an engineer, please check through the details below because some faults can be rectified
easily without the need to call out an engineer. If service is called to resolve a problem listed below or to repair
a fault caused by incorrect installation or mis-use, there is a risk that you will be responsible for the cost.
- 13 -
Technical data
Dimensions Height
686 mm
Width 595 mm + hinge
Depth 420 mm (with door closed)
Depth 900 mm (with door opened 90°)
Weight Net 32 kg
Capacity Cotton 3,4 kg
Synthetics
1,5 kg
Electrical data Power supply 230 V - 50 Hz
Fuse 10 A
Motor
170 W
Power rating 2170 W
Service
Service and Spare Parts
Before calling service, use the trouble shooting table «If
t
he machine is not working» to try to attend to the fault
yourself.
Servicing and repairs must be carried out by a service
company authorised by the supplier. Use only spare
parts supplied by these.
Note that electrical faults should always be rectified by
a certified electrician.
Please make sure you give the product and serial number
of the appliance. This information can be found on the
rating plate on the appliance.
Y
ou can note these details here:
TYPE: ............................................................
MOD: ............................................................
P
ROD.NO: ............................................................
SER.NO: ............................................................
Date of purchase .....................................................
Installation instructions
- 14 -
Damages
If the dryer has been damaged during transport, you
should immediately notify the company responsible for
delivering it.
Check that the dryer is undamaged. If you discover any
damage, faults or that anything is missing, you should
notify the dealer immediately.
Never leave packaging material in a place
w
here children may play with it.
Accessories supplied with the dryer
Console for wall mounting
Optional extra accessories
Mounting kit for installation on top of a washing machine
150 62 99-00
Drain hose 5647 12 28-10
You can ordered the extra accessories from the same
place where you bought the dryer or direct from the
supplier. (Please specify the relevant part number as
shown here).
Identification of materials
All materials used in packaging the dryer are
environmentally-friendly. The various plastics
used are identified and can be recycled:
• PE stands for polyethylene, which is used for the
bag around the dryer and the bag in which these
instructions were supplied.
• PS stands for (moulded) polystyrene, which is used
for the sections of packaging needed to cushion the
dryer.
The cardboard components of the packaging are made
from recyclable paper and should be taken to a collection
point for recycling.
Unpacking the machine
- 15 -
Installation
Positioning
You can install this dryer in a number of different ways.
W
e will show you the most suitable of these. Whichever
way you install it, here are some points to bear in mind:
● Always ensure that the dryer is level for optimum
functioning.
● The temperature in the room should not exceed
+35° C when the dryer is operating. If it does,
open a door or window while the dryer is on. The
dryer uses the air in the room for cooling.
● The area around the dryer should be as dust-free
as possible.
● If you install the dryer with its door hinge side
towards a wall, or next to a cupboard or wall unit
which is more than 370 mm deep, you will need
to leave a space on the hinge side at least 30 mm
wide. This is to allow the door to open wide enough
for removing the water tank.
● Ensure the air ducts are not obstructed.
● The dryer must not be installed above a bath or
in a shower area.
The adjustable feet must not be removed,
they ensure that there is adequate ventilation
underneath the dryer.
Electrical supply
The dryer is supplied with a lead and electrical plug for
connection to an earthed wall socket 230 V 10 A.
If the dryer is installed in a bathroom without
fixed wiring to the electrical supply, an earth
leakage circuit breaker (or RCD) must be
used.
Permanent electrical installation must be
carried out by an authorized electrician.
- 16 -
Installation
3
Wall mounting
Different wall materials require different types of mounting
hardware. Purchase mounting hardware suited to the walls
i
n your home. Use a minimum of 3 suitable fasteners to
attach your mounting console to the wall.
Before deciding on the wall mounting site, it is important
to check that the electrical lead will reach the wall socket
o
nce the dryer is in place.
All electrical work performed on the dryer
should be done by a qualified electrician or
competent person.
If you are installing the dryer between wall-mounted cup-
boards, you should use the wall mounting console. If the
a
djacent cupboards are more than 370 mm deep, don’t
f
orget to leave a space at least 30 mm wide on the left of
the dryer so that the door can open wide enough.
There should be a clear space at least 200 mm high bet-
ween the top of the dryer and the ceiling or any cupboard
above the dryer, to ensure adequate ventilation at the top.
Sodervanie
Dlq polxzowatelq
Informaciq po bezopasnosti 18
– Ustanowka i tehni^eskoe obsluviwanie
– Bezopasnostx detej
– Ispolxzowanie pribora
– Utilizaciq otsluviw[ego swoj srok pribora
Ob]aq informaciq 19
Opisanie pribora 20-21
Instrukcii po ispolxzowani@ 22
– Pered perwym ispolxzowaniem
– Wmestimostx
– Primery wesa nekotoryh widow belxq
Tablica programm 23
– |nergopotreblenie
Indikatory 24
Uhod i o^istka 25-26
– ~istka filxtrow
– ~istka kondensatora
– Oporovnenie emkosti dlq wody
Esli su[ilxnyj baraban ne
rabotaet 27
Tehni^eskoe obsluviwanie 28
– Tehni^eskoe obsluviwanie i zap^asti
Dlq ustanow]ika
Tehni^eskie dannye 28
Raspakowka 29
– Powrevdeniq
– Aksessuary k su[ilxnomu barabanu
– Dopolnitelxnye aksessuary
– Obozna^enie materialow
Ustanowka 30-31
– Raspolovenie pribora
– Podsoedinenie k seti
– Kreplenie k stene
- 17 -
- 18 -
Informaciq po bezopasnosti
Pered ustanowkoj i ispolxzowaniem su[ilxnogo barabana wnimatelxno pro^itajte instrukci@, w tom
^
isle prawila i sowety po bezopasnosti. Znanie instrukcii pozwolit wam ispolxzowatx pribor
maksimalxno \ffektiwno i prodlitx srok ego \kspluatacii. Kavdyj polxzowatelx su[ilxnogo
barabana dolven t]atelxno oznakomitxsq s instrukciqmi po ispolxzowani@ i bezopasnosti. Hranite
instrukci@ w nadevnom meste i prosledite za tem, ^toby instrukciq w slu^ae prodavi pribora
pere[la wmeste s priborom k nowomu wladelxcu.
Ustanowka i tehni^eskoe
obsluviwanie
● Wse raboty po ustanowke i podkl@^eni@ dolvny
prowoditxsq tolxko kwalificirowannym tehnikom.
Raboty, prowedennye nekwalificirowannym personalom,
mogut neblagopriqtno otrazitxsq na rabote pribora i
powle^x za soboj trawmy i u]erb.
● Pribor imeet zna^itelxnyj wes, budxte ostorovny,
kogda wy ego podnimaete.
● Esli su[ilxnyj baraban ustanowlen w wannu@ bez
fiksirowannogo \lektri^eskogo podkl@^eniq, to
neobhodimo ispolxzowatx ustrojstwo za]itnogo
otkl@^eniq (UZO).
● Wilku setewogo [nura nuvno wkl@^atx w zazemlennu@
rozetku \lektroseti, raspolovennu@ w legkodostupnom
meste. Fiksirowannoe podkl@^enie pribora dolvno
osu]estwlqtxsq tolxko upolnomo^ennym na \to \lektrikom.
● Esli kabelx pitaniq powrevden, on dolven bytx zamenen
specialxnym kabelem pitaniq, rekomendowannym
proizwoditelem wa[ego pribora. Obra]ajtesx w
awtorizowannye centry.
● Pribor ni w koem slu^ae ne dolven stoqtx na \lektro-
prowode. W slu^ae, esli su[ilxnyj baraban stoit na
pokrytom kowrom polu, sledite za tem, ^toby wentilq-
cionnye otwerstiq wnizu dwercy ne byli zablokirowany.
● Ne snimajte regulirowo^nye novki, oni sluvat dlq
obespe^eniq wentilqcii nivnej ^asti su[ilxnogo
barabana.
● Tehni^eskoe obsluviwanie i remont dolvny osu]es-
twlqtxsq serwisnoj kompaniej, upolnomo^ennoj na \to
postaw]ikom pribora. Ispolxzujte tolxko firmennye
zapasnye ^asti, predostawlennye postaw]ikom. Nikogda
ne pytajtesx otremontirowatx pribor samostoqtelxno.
Bezopasnostx detej
● Pomnite, ^to plastikowye ^asti upakowki pribora
predstawlq@t serxeznu@ opasnostx dlq igra@]ih detej.
● Tolxko wzroslye mogut ispolxzowatx su[ilxnyj baraban.
Ne pozwolqjte detqm igratx s barabanom ili prikasatxsq
k ego regulqtoram i podwivnym ^astqm.
● Pered zagruzkoj belxq w baraban prowerxte, net li w
nem postoronnih predmetow ili doma[nih viwotnyh.
Ispolxzowanie pribora
● Dannyj su[ilxnyj baraban prednazna^en dlq oby^noj
s
u[ki belxq w doma[nih uslowiqh i tolxko w sootwetstwii
s dannymi instrukciqmi. Ispolxzowanie w l@byh drugih
celqh wle^et za soboj risk powrevdeniq pribora i
trawm dlq polxzowatelq.
● Ne peregruvajte baraban (sm. instrukcii po ispolx-
zowani@).
● Nikogda ne wkl@^ajte su[ilxnyj baraban, esli worsowyj
filxtr ne o^i]en i ne ustanowlen na mesto, ili esli
worsowyj filxtr powrevden (\to movet wyzwatx peregrew
ili por^u belxq).
● Wozxmite za prawilo ^istitx kondensator ^erez
opredelennye promevutki wremeni. Sodervanie
kondensatora w ^istote pozwolit priboru rabotatx
\ffektiwnee i bystree prowoditx su[ku.
● Belxe, obrabotannoe kakimi-libo himi^eskimi sredstwami
kak, naprimer, pqtnowywoditelx i t.p., nelxzq su[itx w
su[ilxnom barabane, poskolxku ispareniq \tih himikatow
ogneopasny.
● Sledu@]ie izdeliq ne sleduet su[itx w su[ilxnom
barabane:
– Podu[ki, l@bye izdeliq nabitye perom, puhom i
t.p. (su[ka \tih izdelij trebuet bolx[ih zatrat
tepla, ^to movet priwesti k peregrewu pribora).
– {erstqnye izdeliq, tak kak oni swaliwa@tsq pod
wozdejstwiem wysokih temperatur
– Osobenno delikatnye tkani, takie kak
sinteti^eskie zanaweski, [elk i t.d.
– Izdeliq iz wspenennoj reziny i rezinopodobnyh
materialow
● Wsegda wykl@^ajte su[ilxnyj baraban posle ispolxzowaniq.
Utilizaciq otsluviw[ego swoj
srok pribora
Simwol na izdelii ili na ego upakowke ukazywaet, ^to
ono ne podlevit utilizacii w ka^estwe bytowyh othodow.
Wmesto \togo ego sleduet sdatx w sootwetstwu@]ij punkt
priemki \lektronnogo i \lektpooboru dowaniq dlq
posledu@]ej utilizacii. Sobl@daq prawila utilizacii
izdeliq, Wy pomovete predotwratitx pri^inenie
okruva@]ei srede i zdorowx@ l@dej potencialxnogo
u]erba, kotoryj wozmoven, w protiwnom slu^ae,
wsledstwie nepodoba@]ego obra]eniq s podobnymi
othodami. Za bolee podrobonj
informaciej ob utilizacii
\togo izdeliq prosxba obra]atxsq k mestnym wlastqm, w
sluvbu po wywozu i utilizacii othodow
ili w magazii, w
kotorom Wy priobreli izdelie.
- 19 -
Ob]aq informaciq po stirke i su[ke belxq
Sortirowka
Wsegda sortirujte belxe w zawisimosti ot materiala
(prowerqjte po qrlyku na izdelii) i wremeni, kotoroe wy
namereny ego su[itx. Belxe dolvno swobodno levatx w
b
arabane. Zastegnite zastevki molnii i zawqvite wse
t
esemki, lqmki i lento^ki. Na pododeqlxnikah i nawolo^kah
zastegnite wse zastevki, ^toby w nih ne nabilisx bolee
melkie we]i.
Otvim (udalenie wody)
Belxe dolvno bytx t]atelxno otvato. My rekomenduem
ispolxzowatx dlq \togo stiralxnu@ ma[inu so skorostx@
otvima minimum 800 oborotow w minutu ili specialxnu@
centrifugu (gidro\kstraktor). ~em wy[e skorostx otvima,
tem bystree wa[ su[ilxnyj baraban wysu[it belxe i
bolee \ffektiwnym s to^ki zreniq rashoda \nergii
budet wesx process su[ki.
Dave izdeliq s detalqmi vestkoj formy (naprimer,
ruba[ki) nuvno otvatx pered su[koj w te^enie 10-30 sek.
Opredelenie wesa zagruvaemogo
belxq
W perepolnennom barabane belxe silxno mnetsq. W to ve
wremq su[ka sli[kom malenxkogo koli^estwa belxq ne
\konomi^na.
Wors
Pri perwom ispolxzowanii was, wozmovno, udiwit koli^estwo
obrazu@]egosq w processe su[ki worsa. |to absol@tno
normalxno i ne zna^it, ^to su[ilxnyj baraban portit
wa[u odevdu.
No[enaq odevda, postirannaq wru^nu@ ili w ma[ine,
terqet wors, no on ostaetsq na powerhnosti materiala.
Esli wy wysu[ite belxe na ulice, to wors budet unositxsq
wetrom. W su[ilxnom barabane wors popadaet na filxtr
i skapliwaetsq tam w processe su[ki.
L@di, strada@]ie allergiej ili astmoj, osobenno
^uwstwitelxny k nali^i@ worsa.
Usadka
W zawisimosti ot ka^estwa trikotavnye tkani osobenno
razli^a@tsq po swoej sposobnosti k usadke. ~toby izbevatx
usadki, trikotavnye izdeliq ne sleduet peresu[iwatx.
Inogda usadka kompensiruetsq sposobnostx@ rastqgiwatxsq.
My sowetuem wam imetx w widu \tu osobennostx trikotavnyh
izdelij pri pokupke nowoj odevdy.
Nakrahmalennye izdeliq
Nakrahmalennoe belxe movno su[itx w su[ilxnom barabane.
Dlq polu^eniq bezupre^nogo rezulxtata wyberite revim,
pri kotorom belxe ostaetsq ^utx wlavnym posle su[ki,
n
aprimer, wyberite programmu awtomati^eskoj su[ki
”
wlavnoe (Dlq glavki)”. Posle su[ki wytrite wnutrenn@@
powerhnostx barabana wlavnoj tkanx@, ^toby udalitx
wozmovnye sledy krahmala na stenkah barabana.
~to nelxzq su[itx w su[ilxnom
barabane
Osobenno delikatnye izdeliq, takie kak zanaweski iz
sintetiki, izdeliq iz [ersti, [elk, tkani s
metalli^eskimi nitqmi, nejlonowye ^ulki i kolgotki,
izdeliq izgotowlennye iz wspenennoj reziny ili
rezinopodobnyh materialow.
O^ewidno, ne sleduet su[itx w ma[ine
izdeliq, kotorye dlq \togo ne prednazna^eny.
Oby^no \ti izdeliq pome^eny dannym
simwolom.
Izdeliq, obrabotannye legko wosplame-
nqemymi vidkostqmi (benzin, spirt,
pqtnowywoditeli i t.p.), ne sleduet
su[itx w su[ilxnom barabane - estx
risk wosplameneniq. Wsegda sledujte
instrukciqm izgotowitelq odevdy.
Rekomendowana su[ka w barabane
Su[itx w razlovennom sostoqnii
- 20 -
1. Dwernaq za]elka (
^toby otkrytx dwercu
podwinxte za]elku wprawo). Izbegajte otkrywatx
dwerx wo wremq su[ki.
2. Mesto dlq shemy programm
(samokle@]aqsq \tiketka)
3. Panelx uprawleniq
4. Wypusk teplogo wozduha
5. Wentilqcionnye otwerstiq - ne dolvny
bytx zablokirowany.
6. Kondensator
Kondensator wstroen w dwercu, ego nuvno periodi^eski
^istitx.
7. Filxtry
Filxtry nuvno pro^i]atx do ili posle kavdogo
ispolxzowaniq. Worsowyj filxtr raspoloven za
filxtrom gruboj o^istki, i ego movno snqtx i
po^istitx.
8. Reguliruemye novki
Esli pribor ne wisit na stene, to polovenie pribora
movno wyrownqtx s pomo]x@ reguliruemyh novek.
9. Tabli^ka s tehni^eskimi dannymi
10. Baraban
11. |lektri^eskij kabelx
12. Kreplenie kron[tejna pri ustanowke
na stene
Opisanie pribora
9
10
14
6
7
5
8
4
3
2
2
1
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
Strona jest ładowana ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
w innych językach
- English: Electrolux EDC3250 User manual
Powiązane dokumenty
Inne dokumenty
-
Zanussi TCE7124 Instrukcja obsługi
-
HOTPOINT/ARISTON AQC9 BF7 T (EU) instrukcja
-
-
Candy EVOC 581B-S Instrukcja obsługi
-
-
-
-
-
Zanussi FCS920C Instrukcja obsługi
-