Yamaha YSTM8 Instrukcja obsługi

Kategoria
Głośniki soundbar
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

POWERED MULTIMEDIA SPEAKERS
YST-M8
Active Servo
Technology
Active Servo
Technology
VOLUME
TONE
UCA
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
OWNER’S MANUAL / MODE D’EMPLOI
English .............................. 4
Français ............................ 9
2
SAFETY INSTRUCTIONS
1 Read Instructions — All the safety and operating instructions
should be read before the unit is operated.
2 Retain Instructions — The safety and operating instructions
should be retained for future reference.
3 Heed Warnings — All warnings on the unit and in the operating
instructions should be adhered to.
4 Follow Instructions — All operating and other instructions
should be followed.
5 Water and Moisture — The unit should not be used near water –
for example, near a bathtub, washbowl, kitchen sink, laundry
tub, in a wet basement, or near a swimming pool, etc.
6 Carts and Stands — The unit should be
used only with a cart or stand that is
recommended by the manufacturer.
6A An unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
unit and cart combination to overturn.
7 Wall or Ceiling Mounting — The unit should be mounted to a
wall or ceiling only as recommended by the manufacturer.
8 Ventilation — The unit should be situated so that its location or
position does not interfere with its proper ventilation. For
example, the unit should not be situated on a bed, sofa, rug, or
similar surface, that may block the ventilation openings; or
placed in a built-in installation, such as a bookcase or cabinet
that may impede the flow of air through the ventilation openings.
9 Heat — The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce heat.
10 Power Sources — The unit should be connected to a power
supply only of the type described in the operating instructions or
as marked on the unit.
11 Power-Cord Protection — Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the unit.
12 Cleaning — The unit should be cleaned only as recommended
by the manufacturer.
13 Nonuse Periods — The power cord of the unit should be
unplugged from the outlet when left unused for a long period of
time.
14 Object and Liquid Entry — Care should be taken so that objects
do not fall into and liquids are not spilled into the inside of unit.
15 Damage Requiring Service — The unit should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the enclosure damaged.
16 Servicing — The user should not attempt service the unit
beyond those means described in the operating instructions. All
other servicing should be referred to qualified service personnel.
17 Power Lines — An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization — Precautions should be taken so
that the grounding or polarization is not defeated.
3
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product,
when installed as indicated in the instructions contained in this manual,
meets FCC requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to use the
product.
2. IMPORTANT: When connecting this product to accessories and/or
another product use only high quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC authorization to use
this product in the USA.
3.
NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level
of assurance that your use of this product in a residential environment will
not result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed
and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interfer-
ence will not occur in all installations. If this product is found to be the
source of interference, which can be determined by turning the unit
“OFF” and “ON”, please try to eliminate the problem by using one of
the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker of
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna.
If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to
coaxial type cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If
you can not locate the appropriate retailer, please contact Yamaha
Corporation of America, 6600 Orangethorpe Ave, Buena Park, CA 90620
The above statement apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
POUR LES CONSOMMATEURS CANADIENS
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring
or distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is
often undetectable until it is too late,
YAMAHA and the Electronic Industries
Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure
from excessive volume levels.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
We Want You Listening For A Lifetime
4
System Example / Exemple de connexion
1
PORTABLE CD PLAYER / LECTEUR DE CD PORTATIF
2
KEYBOARD / CLAVIER / KEYBOARD
3
CD-ROM PLAYER / LECTEUR DE CD ROM
4
PERSONAL COMPUTER / ORDINATEUR INDIVIDUEL
5
SUBWOOFER / HAUTEUR PARLEUR D’EXTREME-GRAVE
6
3.5 mm stereo mini plug cable / Câble à minifiches stéréo 3,5 mm
7
RCA plug cable / Câble à fiches RCA
8
AC Adaptor / Adaptateur CA
*
The AC adaptor varies depending on the country of destination. / Le modèle de l’adaptateur secteur dépend du pays de destination.
L
MADE IN CHINA
TO
RIGHT
SPEAKER
SER. NO.
POWERED SPEAKER
MODEL NO. YST-M8
*
1
2
3
4
7
5
6
6
8
R
INPUT 1
INPUT 2
TO
LEFT
SPEAKER
OUTPUT
(ADJ.VOL.)
DC 12V
SER. NO.
MADE IN CHINA
POWERED SPEAKER
MODEL NO. YST-M8
BASS VOLUME
POWERED MULTIMEDIA SUBWOOFER YST-MSW8
010010
5
Front & Rear Panel / Face et Face arrière
7
8
9
6
MADE IN CHINA
INPUT 1
INPUT 2
TO
LEFT
SPEAKER
OUTPUT
(ADJ.VOL.)
DC 12V
MADE IN CHINA
TO
RIGHT
SPEAKER
1
2
3
4
5
R
SER. NO.
POWERED MULTIMEDIA
SPEAKERS
MODEL NO. YST-M8
L
SER. NO.
POWERED MULTIMEDIA
SPEAKERS
MODEL NO. YST-M8
VOLUME
TONE
6
Cautions
Please read the following operating precautions before use:
Use the AC adaptor designed specifically for the YST-M8 only. Yamaha
cannot be held responsible for damage caused by using other power supply
adaptors.
When disconnecting the AC adaptor from an AC receptacle, hold and pull the
adaptor, not the power cord.
If the YST-M8 are not going to be used for a while, disconnect the AC adaptor
from the AC receptacle.
Always disconnect the AC adaptor from the AC receptacle before making any
connections.
YST-M8 do not contain any user serviceable parts. Refer all servicing to your
Yamaha dealer.
Do not expose the YST-M8 to temperature extremes, direct sunlight, excessive
dust, humidity, or vibration.
Place the YST-M8 on a level, stable surface. Do not drop the YST-M8, apply
excessive force to their controls, or put heavy items on top of them.
If the YST-M8 should require cleaning, use a soft cloth. If necessary, use a
damp cloth.
To protect the YST-M8 speakers, avoid microphone feedback, continuous and
excessive output from electronic musical instruments amplifiers signal
distortion.
If the YST-M8 are located close to fluorescent or neon type lights, a slight
hum may be heard. In this case, relocate the YST-M8 away from the light.
Although the YST-M8 speakers are magnetically shielded, keep floppy disks
and tapes away from them.
The YST-M8 may cause picture distortion when placed close to a television or
computer monitor. In this case, move them away a little.
Thank you for purchasing Yamaha’s YST-M8 Powered Multimedia Speakers. Yamaha’s Active Servo Technology offers
exceptional high performance.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off.
This state is called the standby mode.
In this state, this unit is designed to consume a very small quantity
of power.
Connections
Refer to page 4 for system connections.
Rear Panel (right cabinet) (Refer to page 5)
1 INPUT 1 and 2: These are 3.5 mm jack connections for inputting signals to
the YST-M8. Using these two inputs will mix two input signals.
For example, you may connect your CD-ROM player and personal computer
to these input terminals.
2 TO LEFT SPEAKER: This should be connected to the TO RIGHT
SPEAKER connection on the left-channel cabinet using the supplied RCA
plug cable.
3 OUTPUT (ADJ. VOL.): This 3.5 mm stereo jack outputs the input signal
after the VOLUME control.
4 DC 12V: Connect the supplied AC adaptor to this connection.
Rear Panel (left cabinet)
5 TO RIGHT SPEAKER: This should be connected to the TO LEFT
SPEAKER connection on the right cabinet using the supplied RCA plug cable.
7
Specifications
Type Active Servo Technology
Output power 5 W + 5 W (1 kHz, 4 )
Input sensitivity 200 mV (1 kHz, 4 at 5 W)
Input Impedance 25 k
Frequency response 80 Hz to 20 kHz
Speaker unit
6.5 cm (2.5") full-range cone, magnetic shielding
Output Impedance 600
Output level 0.9 V (at 200 mV Rated Input)
Power supply DC 12 V
U.S.A. and Canada models AC 120 V, 60 Hz
Europe and U.K. models AC 230 V, 50 Hz
Australia model AC 240 V, 50 Hz
Dimensions (W×H×D) 86 (3
3
/
8
") × 216 (8
1
/
2
") × 130 (5
1
/
8
") mm
Weight 0.7 kg (1 lb 9 oz.)/Right channel unit
0.6 kg (1 lb 5 oz.)/Left channel unit
Finish YST-M8 W: Computer white
YST-M8 B: Black
Accessories AC adaptor × 1
3.5 mm stereo mini plug cable × 1
RCA plug cable × 1
8 non skid pads × 1
* Specifications subject to change without notice.
Non skid Pads
The pads supplied with the YST-M8 should be stuck onto
the bottom of each speaker cabinet as shown. As well as
preventing the YST-M8 from slipping around, these pads
also isolate the cabinet from the mounting surface.
Controls
Front Panel (right cabinet) (Refer to page 5)
6 (power) switch and indicator: Press the (power) switch to turn on the
YST-M8; the indicator will light up. Press it again to turn off. Before
turning on and off, turn down the VOLUME control.
7 VOLUME control: Use this control to set the volume level. Turn it clockwise
to increase the volume, and counterclockwise to reduce it.
8 TONE control: This control allows frequency boost and cut up to ±7 dB at
10 kHz. This tends to emphasize vocals, providing a warmer intimate sound.
Turn it clockwise to boost, and counterclockwise to cut.
9 (headphones) jack: Use this jack to connect stereo headphones for
monitoring. No sound is output from the speakers or the OUTPUT
(ADJ.VOL.) jack when headphones are connected.
English
8
Troubleshooting
If your speakers fail to operate normally, check the following table. It lists common operating errors and simple measures which you can take to correct the problem. If it
cannot be corrected, or the symptom is not listed, disconnect the speaker’s AC adaptor and contact your authorized YAMAHA dealer or service center for help.
FAULT
No sound comes from one, or both of
the speakers.
No sound comes from the unit
connected to the OUTPUT (ADJ.VOL.)
jack on the rear panel.
Sound is distorted.
Noise is heard when the power is
turned on.
Noise.
CURE
Insert the AC adaptor firmly into the wall outlet.
Turn ON the (power) switch (the indicator lights).
Make the connections again, firmly, or use a different
cable.
Turn VOLUME control to the right to increase the
volume.
Turn up the volume on the connected component.
Disconnect the headphones.
Turn down the volume on the connected component.
Connect the power cord to an UNSWITCHED AC
OUTLET.
Make sure to use the (power) switch on this unit to
turn on and off.
Make the connections again, firmly, or use a different
cable.
CAUSE
The AC adaptor is not properly plugged in to the wall
outlet.
The (power) switch is turned OFF.
Connections are faulty or incomplete.
The volume is set to minimum.
The signal being input is too small.
Headphones are connected.
(No sound comes from the OUTPUT jack when
headphones are connected.)
The signal being input is too large.
The power cord of this unit is connected to another
unit’s SWITCHED AC OUTLET.
Connections are faulty or incomplete.
Even if the (power) switch is set to off, a small amount of sound may be heard from the headphones if the VOLUME control is turned fully clockwise to the
maximum position.
12
Printed in China
IP
V287500
IMPORTANT!
Please record the serial number of this unit in the space below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Yamaha YSTM8 Instrukcja obsługi

Kategoria
Głośniki soundbar
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla