Yamaha Audiogram6 Instrukcja obsługi

Kategoria
Miksery audio
Typ
Instrukcja obsługi
1
AUDIOGRAM 6 Owner’s Manual
AUDIOGRAM 6
Owner’s Manual
C0 (10.11.30)
EnglishDeutschFrançaisEspañolRussian
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
Руководство пользователя
USB AUDIO INTERFACE
Русский
EnglishDeutschFrançaisEspañol
FR
ES
RU
JA
EN
DE
2
AUDIOGRAM 6 Owner’s Manual
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instruc-
tions. Failure to follow instructions could void your
FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regula-
tions, Part 15 for Class “B” digital devices. Compli-
ance with these requirements provides a reasonable
level of assurance that your use of this product in a
residential environment will not result in harmful inter-
ference with other electronic devices. This equipment
generates/uses radio frequencies and, if not installed
and used according to the instructions found in the
users manual, may cause interference harmful to the
operation of other electronic devices. Compliance
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)
with FCC regulations does not guarantee that inter-
ference will not occur in all installations. If this prod-
uct is found to be the source of interference, which
can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is
being affected by the interference.
Utilize power outlets that are on different branch (cir-
cuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reori-
ent the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfac-
tory results, please contact the local retailer autho-
rized to distribute this type of product. If you can not
locate the appropriate retailer, please contact
Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park,
CA90620
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION (U.S.A.)
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
COMPLIANCE INFORMATION STATEMENT
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party : Yamaha Corporation of America
Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620
Telephone : 714-522-9011
Type of Equipment : COMPUTER RECORDING SYSTEM
Model Name : AUDIOGRAM 6
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
(FCC DoC)
(class b korea)
3
AUDIOGRAM 6 Owner’s Manual
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the
following:
Do not open the device or attempt to disassemble the internal parts or
modify them in any way. The device contains no user-serviceable
parts. If it should appear to be malfunctioning, discontinue use
immediately and have it inspected by qualified Yamaha service
personnel.
Do not expose the device to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might
spill into any openings. If any liquid such as water seeps into the
device, unplug the USB cable from this device immediately. Then have
the device inspected by qualified Yamaha service personnel.
Never insert or remove a USB cable with wet hands.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
Before moving the device, remove all connected cables.
•Avoid setting all volume controls to their maximum. Depending on the
condition of the connected devices, doing so may cause feedback and
may damage the speakers.
Do not expose the device to excessive dust or vibrations, or extreme
cold or heat (such as in direct sunlight, near a heater, or in a car during
the day) to prevent the possibility of panel disfiguration or damage to
the internal components.
Do not place the device in an unstable position where it might
accidentally fall over.
Do not use the device in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Doing so may result in noise,
both in the device itself and in the TV or radio next to it.
Before connecting the device to other devices, turn off the power for all
devices. Before turning the power on or off for all devices, set all
volume levels to minimum.
When turning on the AC power in your audio system, always turn on
monitor speakers LAST, to avoid speaker damage. When turning the
power off, monitor speakers should be turned off FIRST for the same
reason.
Do not insert your fingers or hands in any gaps or openings on the
device.
•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)
into any gaps or openings on the device. If this happens, unplug the
USB cable from the device immediately. Then have the device
inspected by qualified Yamaha service personnel.
Do not use the device or headphones for a long period of time at a high
or uncomfortable volume level, since this can cause permanent
hearing loss. If you experience any hearing loss or ringing in the ears,
consult a physician.
Do not rest your weight on the device or place heavy objects on it, and
avoid use excessive force on the buttons, switches or connectors.
Do not open Water warning
Location
Connections
Handling caution
(5)-10 1/2
4
AUDIOGRAM 6 Owner’s Manual
Always unplug the USB cable from a computer or turn off the computer to turn off the device when the device is not in use.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult
qualified Yamaha service personnel about replacing defective components.
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please
check with your Yamaha dealer.
SPECIAL NOTICES
This manual is the exclusive copyright of Yamaha Corporation.
The included software is the exclusive copyright of Steinberg Media Technologies GmbH.
Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the written consent of the
manufacturer.
•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the
results of the use of this manual and the software.
This disk containing the software is not meant for use with an audio/visual system (CD player, DVD player, etc.). Do not attempt to use the disk
on equipment other than a computer.
Future upgrades of application and system software and any changes in specifications and functions will be announced separately.
The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the screens which
appear on your computer.
The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat different from those on
your instrument.
This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which it has license
to use others' copyrights. Such copyrighted materials include, without limitation, all computer software, music data, etc. Any unauthorized use of
such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal consequences.
DON'T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.
Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.
Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.
The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.
MIC/INST jacks (XLR-type) are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
21
3
(5)-10
2/2
5
AUDIOGRAM 6 Owner’s Manual
Introduction................................................................. 5
Contents .......................................................................................5
Features .......................................................................................6
Setup............................................................................ 7
Quick Guide................................................................. 8
1. Installing Cubase AI .................................................................8
2. Connecting to the AUDIOGRAM interface ...............................8
3. Powering Up the System..........................................................9
4. Adjusting Level .........................................................................9
5. Recording with Cubase AI......................................................10
6. Mixing with Cubase AI............................................................14
Controls and Functions ........................................... 15
Input Signal Flow........................................................................16
Troubleshooting ....................................................... 17
Specifications ......................................................... 104
General Specifications .............................................................104
Dimensional Diagrams .............................................................104
Block Diagram and Level Diagram...........................................105
About the accessory disk ...................................... 106
Introduction
Thank you for choosing a Yamaha AUDIOGRAM 6 Computer Recording System. The AUDIOGRAM 6
includes a USB audio interface for digital audio data transfer, and Cubase AI DAW (Digital Audio Worksta-
tion) software for Windows® and Macintosh® computer operating systems. With the AUDIOGRAM 6 and
your personal computer you have the basic elements of a high-performance computer recording system that
is easy to set up and operate.
Please read through this manual carefully before beginning use, so that you will be able to take full advan-
tage of your interface’s superlative features and enjoy trouble-free operation for years to come. After reading
the manual, please store it in a safe place.
Contents
Introduction
6
AUDIOGRAM 6 Owner’s Manual
Connect To Your Computer via a Single USB Cable (page 8)
The AUDIOGRAM interface connects to your computer via the supplied USB cable. Stereo audio data is
transferred in both directions—from the interface to the computer, and vice-versa—via the USB connection
(44.1 kHz or 48 kHz sampling frequency).
No Driver Installation Required (page 8)
The AUDIOGRAM system uses the standard drivers included in your computer’s operating system, so
there’s no need to install any extra driver software.
Cubase AI DAW Software Supplied (page 8)
Cubase AI software, included in the AUDIOGRAM package, offers versatile, high-performance hard-disk
recording capability.
Compression (page 16)
Compression increases the overall level without introducing distortion by compressing excessive peaks in
the signals from microphones and guitars.
48V Phantom Power (page 16)
A PHANTOM switch supplies +48V phantom power to the channel 1 microphone input, so you can use
high-quality phantom-powered condenser microphones for superior recording quality.
Features
Accessories
Cubase AI DVD-ROM
USB cable
Owner’s Manual (this book)
7
AUDIOGRAM 6 Owner’s Manual
Setup
Microphone
Guitar
CD player
Keyboard, etc.
Computer
Headphones
Powered speakers
To connect a device such
as a microphone:
To connect an instrument
such as an electric guitar
or bass:
USB cable
Cubase AI
Be sure to turn the PHANTOM
+48V switch () on when
using a phantom-powered
condenser microphone.
8
AUDIOGRAM 6 Owner’s Manual
Quick Guide
This quick setup and operation guide covers everything from installing the Cubase AI software to using
Cubase AI for recording and mixdown. While going through this section you might find it useful to also
refer to the “Controls and Functions” section on page 15, as well as the pdf manual supplied with the
Cubase AI software.
You are only permitted to use this software pursuant to the terms and conditions of the
“Steinberg Software End User License Agreement (EULA)” shown during the installation.
1
Start the computer and log on to the Administrator account.
2
Insert the included DVD-ROM into the computer’s DVD-ROM drive.
3
Follow the on-screen instructions to install the Cubase AI software.
In order to have continuous use of Cubase AI, including support and other benefits, you will need
to register the software and activate your software license by starting it while the computer is
connected to the Internet. Click the “Register Now” button shown when the software is started,
then fill in all required fields for registration. If you do not register the product, you will be unable
to use the application after a limited period of time expires.
•To install on Mac computers double-click the “Cubase AI*.mpkg” icon or the “Cubase AI* Start
Center” icon.
“*” indicates where the version number appears in the actual icon name.
Visit the web address below for the latest information on:
<http://www.yamahasynth.com/>
1
Turn all gear that is to be connected to the
AUDIOGRAM off or to standby mode (except
the computer), and set the LEVEL controls,
MASTER LEVEL control and DAW control to
their minimum settings.
2
Connect microphones and/or instruments.
For details on making connections refer to the
“Setup” section on page 7 and the “Controls and
Functions” section on page 15.
3
Set the MIC/INST switch according to the
type of device connected to channel 1 or 2.
Select MIC ( ) if a microphone is connected, or
INST ( ) if a guitar or similar instrument is con-
nected.
4
To use channels 1 and 2 as independent mono
channels set the MONO/STEREO switch to
MONO ( ). To use channels 1 and 2 as a ste
-
reo pair set the switch to STEREO ( ).
Step
1
Installing Cubase AI
Step
2
Connecting to the AUDIOGRAM interface
Important!
NOTE
LEVEL controls
MASTER LEVEL control
DAW
control
Be sure to turn the
PHANTOM +48V switch
on when using a phantom-
powered condenser
microphone.
Quick Guide
9
AUDIOGRAM 6 Owner’s Manual
To prevent loud pops and noises, turn on the power
to your sound gear starting with the sources
(instruments, CD players, etc.) and ending with the
monitor speakers (powered speakers).
1
Turn on the instruments and microphones.
2
If you are using a condenser microphone for
the channel 1, turn on the PHANTOM +48V
switch.
Observe the following precautions when
turning on phantom power.
Make sure that the PHANTOM +48V switch
is off when phantom power is not needed.
When turning the switch on, be sure that
only a condenser microphone is con-
nected to the channel 1 MIC/INST input
jack. Other devices may be damaged if
connected to phantom power. This precau-
tion does not apply to balanced dynamic
microphones or instruments with the
phone jack, however, as these will not be
affected by phantom power.
•To prevent damage to speakers, be sure to
turn off power amplifiers (or powered
speakers) before turning this switch on or
off. We also recommend that you set the
MASTER LEVEL control to the minimum
position before operating this switch to
avoid the risk of loud noises that could
cause hearing loss or device damage.
3
Connect the AUDIOGRAM interface to your
computer using the supplied USB cable.
The POWER indicator will light to indicate that power
is being applied to the AUDIOGRAM interface.
When connecting or disconnecting the USB
cable be sure to turn the DAW control and the
MASTER LEVEL control all the way down.
The first time you connect to the computer’s
USB connector, or change the connection to
a different USB port, a driver installation dis-
play may appear. If this occurs, wait until the
installation is complete before proceeding.
4
Turn the power to the monitor speakers
(powered-speakers).
1
Set the GAIN controls to the minimum position
and the LEVEL controls to about 1 o’clock.
Set the MASTER LEVEL control to the mini-
mum position. Failure to do so may result in
loud noise bursts that can damage your
equipment, your ears, or both.
2
Adjust the volume on all instruments that are
connected to the AUDIOGRAM interface.
3
Adjust the channel GAIN controls so that the
corresponding PEAK indicators flash briefly
on the highest peak levels.
4
Adjust the overall volume with the MASTER
LEVEL control while monitoring via head-
phones or monitor speakers.
Lower the volume using the LEVEL controls until the
level indicator PEAK LEDs flash only briefly on occa-
sional high-level peaks or not at all.
Step
3
Powering Up the System
CAUTION
USB Connection Precautions
Be sure to observe the following points when connect-
ing to the computer's USB interface.
Failure to observe these rules can result in computer
freezes/hang-ups and possibly data loss or corruption.
If the instrument or computer does hang up, restart the
application or computer.
Be sure to wake the computer from sleep/
suspended/standby mode before making a
connection to the computer’s USB connec-
tor.
•Always quit all applications running on the
computer before connecting or disconnect-
ing the USB cable.
•Wait at least 6 seconds between connecting
or disconnecting the USB cable.
CAUTION
CAUTION
NOTE
Step
4
Adjusting Level
CAUTION
GAIN controls
LEVEL controls
PEAK indicators MASTER LEVEL control
DAW control
Level indicator
Quick Guide
10
AUDIOGRAM 6 Owner’s Manual
This section describes the procedure for recording to the Cubase AI software we installed earlier via the
AUDIOGRAM interface.
Cubase AI 6 is used for the examples in this manual. For details about other versions of Cubase AI or
Cubase AI operation in general, refer to the PDF manual provided with the software.
Cubase AI Setup
1
Set the computer output to the maximum
level.
For details on how to make the setting refer to the
“The recorded sound is too low in level.” section in
the “Troubleshooting” on page 17.
2
Launch Cubase AI.
Windows:
Click [Start] [All Program] [Steinberg Cubase
AI *] [Cubase AI *] to launch the program. (“*”
indicates where the version number appears in the
actual icon name.)
If the ASIO Direct Sound Full Duplex Driver
dialog window appears, click [OK].
Mac:
Double-click the [Application] [Cubase AI*]. “*”
indicates where the version number appears in the
actual icon name.
If you specified a file destination when
installing the Cubase AI software, launch the
application from that location.
Create a Cubase AI shortcut or alias on your
desktop so you can easily launch the pro-
gram when required.
3
When the Project Assistant window appears,
select the [More] menu[Empty] and click
[Create].
A new project is created.
Recorded Cubase AI data is stored as a
“Project.
4
Select [Device Setup] from the [Devices]
menu to open the Device Setup window.
Windows:
Select [VST Audio System] in the [Devices] field on
the left side of the window. Select [ASIO DirectX
Full Duplex Driver] in the [ASIO Driver] field on the
right side of the window. A dialog box will appear
asking “Do you want to switch the ASIO driver?”.
Click [Switch].
Mac:
Select [VST Audio System] in the [Devices] field on
the left side of the window. Select [USB Audio
CODEC] in the [ASIO Driver] field on the right side
of the window. A dialog box will appear asking “Do
you want to switch the ASIO driver?”. Click
[Switch].
Step
5
Recording with Cubase AI
NOTE
NOTE
NOTE
NOTE
Quick Guide
11
AUDIOGRAM 6 Owner’s Manual
5
Select [ASIO DirectX Full Duplex Driver](Win-
dows), [USB Audio CODEC](Mac) in the
[Devices] field on the left side of the Device
Setup window, and click [Control Panel] on
the right side of the window.
Windows:
The ASIO Direct Sound Full Duplex Setup dialog
box will be displayed. Check only the input port and
output port [USB Audio CODEC] checkbox, and
then click [OK] to close the dialog window.
Mac:
The [CoreAudio Device Settings] dialog window
appears. Check only the [USB Audio CODEC]
checkbox in both “Input” and “Output” of the [Input/
Output Configuration] field. Click [Close] to close
the dialog window.
6
Make sure that “USB Audio CODEC 1/2”(Win-
dows), “Front Left/Front Right” (Mac) are
shown in the [Port System Name] field, and
check the [Visible] column in the Device Setup
window. Click [OK] to close the window.
If the [Port System Name] field does not
change, close and restart the Cubase AI,
then open the Device Setup window.
7
Select [VST Connections] from the [Devices]
menu.
Windows:
If “Not Connected” is selected in the [Audio Device]
field, click on the “Not Connected” indication, and
then switch to [ASIO DirectX Full Duplex Driver].
Also set the [Outputs] in the same way, and then
close the window.
Mac:
If “Not Connected” is selected in the [Audio Device]
field, click on the “Not Connected” indication, and
then switch to [USB Audio CODEC].
Also set the [Outputs] in the same way, and then
close the window.
8
Select [Add Track] [Audio] from the
[Project] menu.
The Add Audio Track dialog window appears.
9
Set the “Count” and “Configuration” parame-
ters, and then click [Add Track].
The added tracks will appear.
You will normally use a stereo track when
recording synthesizers, and a monaural
track when recording vocals or guitars.
NOTE
NOTE
Quick Guide
12
AUDIOGRAM 6 Owner’s Manual
Preparing to Record
1
Click in the track list (the area in which the
track names are displayed) to select a track
to record on.
The various settings for the selected track are avail-
able in the Inspector on the left side of the display.
2
Make sure the [Record Enable] button for the
track to be recorded is turned on.
If the [Record Enable] button is off, click it to turn it
on.
3
Play the instrument to be recorded, and
adjust the AUDIOGRAM GAIN controls and
LEVEL controls so that the Clipping indica-
tor never lights.
4
Specify the point at which you want to start
recording via the ruler at the top of the win-
dow for the project.
Click the black area of the ruler to move the project
cursor (the vertical black line) to that position.
Inspector
[Record Enable] button Track list
<Transport panel>
Clipping indicator
Ruler
Quick Guide
13
AUDIOGRAM 6 Owner’s Manual
Recording and Playback
1
Click the Transport panel [Record] button to
begin recording.
When recording is started the project cursor will
begin moving to the right and a box that displays the
recording results will be created.
2
Play the part.
3
When you finish recording the track, click
the Transport panel [Stop] button.
To hear playback of the track you have just recorded,
use either the Transport panel [Rewind] button or the
ruler to rewind to the beginning of the recorded sec-
tion, then click the Transport panel [Start] button.
4
Select [Mixer] from the [Devices] menu to
open the Mixer window.
The overall playback level will be displayed via the
master section bus level meter on the right side of the
mixer window, and the channel level will be dis-
played via the channel strip level meter.
To hear the playback sound via the AUDIO-
GRAM interface, adjust the volume with the
DAW control and MASTER LEVEL control.
The playback level will approximately match
the recording level when the DAW control is
set to about 1 o’clock.
5
To save the project select [Save] from the
[File] menu and enter a file name before actu-
ally saving the file.
Save your project frequently to insure against losing
large amounts of data if a problem occurs.
6
Repeat steps 1 through 5 to record further
material on the same track.
7
To record additional material on a different
track, select a new track and repeat the
record procedure.
Recording with maximum quality and mini-
mum noise:
For optimum sound quality with minimum noise, the
AUDIOGRAM signal levels should be set as high as
possible without clipping. Check signal levels to be
sent to Cubase AI for recording using the AUDIO-
GRAM level indicators while the DAW control is set to
minimum. Adjust the channel LEVEL controls so that
the corresponding PEAK LEDs flash only occasionally
on the highest input transients.
Stop
Record
Start
Rewind
Forward
<Transport panel>
Recording results
NOTE
Level meter Bus level meter
Quick Guide
14
AUDIOGRAM 6 Owner’s Manual
In this section we’ll try mixing down multiple recorded audio tracks to stereo, and creating an audio file.
Mixes can be stored as WAV or AIFF files, which can then be recorded to audio CDs.
1
Launch Cubase AI and open a project file.
2
Click the [Start] button on the Transport
Panel.
3
While listening to playback, drag the channel
strip level faders up and down to create the
desired initial balance, then adjust the over-
all volume using the bus volume fader.
4
Drag the pan controls on the top of the
channel strips left and right to set the ste-
reo position of each track.
5
At this point you can begin to use EQ to
refine your mix, and add effects.
As an example let’s try adding reverb. Click the
[Edit] button ( ) on the left side of the channel
strip to open the VST audio channel settings window.
Click Inserts 1 and select “Reverb - RoomWorks SE.
For further details refer to the pdf manual pro-
vided with the Cubase AI software.
It’s a good idea to lower the channel fader a
bit before adding an effect, since the effect
can cause an increase in the overall channel
level.
6
Double-click the left locator (starting
point) and right locator (ending point) of
the Transport panel. Change each high-
lighted number, and then specify the
position of the locator.
7
When the final mix adjustments have
been made, go to the [File] menu and
select [Export] [Audio Mixdown].
8
Enter a file name and select a destination
for the file as well as a file type.
If you intend to use the file to create an audio CD,
select the WAV file type (AIFF on Mac OS X), 44.1
kHz, and 16 bit.
9
Click [Export].
Progress of the mixdown operation will be shown in
a progress window. When the progress window
closes the mixdown is complete.
Files created by mixdown can be directly
played back using the Windows Media
Player, or iTunes.
Step
6
Mixing with Cubase AI
NOTE
CAUTION
Bar
NOTE
15
AUDIOGRAM 6 Owner’s Manual
Controls and Functions
1 MIC/INST Input Jack
Microphones and instruments such as guitars can be
connected here using XLR or phone jack cables. Set
the MIC/INST switch
5 to MIC or INST according to
the type of device connected.
You can directly connect an electric guitar or
bass without the need for a separate DI
(Direct Injection) box or amp simulator.
2 LINE Input Jacks (L (MONO)/R)
These inputs are intended mainly for use with instru-
ments and equipment having stereo outputs, such as a
synthesizer or CD player.
If you connect to the L (MONO) jack only, the AUDIO-
GRAM will recognize the signal as monaural and will
send the identical signal to both the L and R jacks.
3 STEREO OUT Jacks
These output the mixed signal from channels 1 to 5/6.
The output level can be adjusted using the MASTER
LEVEL control. These jacks would typically be con-
nected to monitor speakers (powered speakers).
4 PHONES Jack
Connects a pair of headphones to this jack. The
PHONES jack outputs the same signal as the STEREO
OUT jacks.
5 MIC/INST Switch
Set this switch according to the type of device con-
nected. Select MIC ( ) if a microphone is connected,
or INST ( ) if an electric guitar or bass is connected.
If a device is not connected to the MIC/
INST jack, set this switch to MIC ( ).
Otherwise noise may occur.
6 GAIN Control
Adjusts the input signal level. To achieve the best bal-
ance between S/N ratio and dynamic range, adjust the
level so that the input channel PEAK indicator
9 lights
only occasionally and briefly on the highest input tran-
sients.
!6
q
w e
t
!1
!2
!3
!4
!5
o
!0
u
i
y
r
XLR-type Phone-type
NOTE
Phone-type
NOTE
Controls and Functions
16
AUDIOGRAM 6 Owner’s Manual
7 COMP Control
Adjusts the amount of compression applied to the chan-
nel. As the knob is turned to the right, the interface
automatically raises the compression ratio while adjust-
ing the output gain accordingly. The result is smoother,
more even dynamics because louder signals are atten-
uated while the overall level is boosted.
Avoid setting the compression too high, as
the higher average output level that results
may lead to feedback.
8 MONO/STEREO Switch
This switch allows channels 1 and 2 to be used either
as separate mono channels or as a stereo pair. When
set to MONO ( ), channels 1 and 2 function as inde-
pendent mono channels feeding both the L and R STE-
REO OUT jacks
3. When set to STEREO ( ), input
channels 1 and 2 function as a stereo pair: the channel
1 signal feeds the L STEREO OUT jack and the chan-
nel 2 signal feeds the R STEREO OUT jack.
9 PEAK Indicators
The PEAK indicators light when the channel signal
reaches or exceeds clipping level. Note that signal lev-
els as indicated by the PEAK indicators are affected by
both the GAIN and LEVEL controls.
If a PEAK indicator lights, adjust the GAIN
6 and
COMP
7 controls to lower the level so that the indica-
tor goes out.
0 LEVEL Controls
Adjusts the level of the channel signal. Use these con-
trols to adjust the balance between the various chan-
nels.
A POWER Indicator
This indicator lights when power is applied to the
AUDIOGRAM interface via the USB cable (supplied)
that connects it to the computer.
B PHANTOM +48V (CH1) Switch/Indicator
(only for channel 1)
This switch toggles phantom power on and off. If you
set the switch on ( ), the AUDIOGRAM supplies
phantom power to channel 1 MIC/INST jack (XLR-type)
1. Turn this switch on when using a phantom-powered
condenser microphone.
Be sure to leave this switch off ( ) if
you do not need phantom power.
When turning the switch on, be sure that
only a condenser microphone is con-
nected to the channel 1 MIC/INST input
jack. Other devices may be damaged if
connected to phantom power. This precau-
tion does not apply to balanced dynamic
microphones or instruments with the
phone jack, however, as these will not be
affected by phantom power.
•To prevent damage to speakers, be sure to
turn off power amplifiers (or powered
speakers) before turning this switch on or
off. We also recommend that you set the
MASTER LEVEL control to the minimum
position. Neglect of these precautions may
result in large noise bursts that may dam-
age your equipment, your ears, or both.
C Level Indicators
These indicators show signal levels prior to the MASTER
LEVEL control
E
. The SIGNAL LED lights when a signal
is present, and the PEAK LED lights when the signal
reaches or exceeds clipping level. Adjust the input chan-
nel LEVEL controls
0
so that the PEAK LEDs flash only
briefly on occasional high-level peaks or not at all.
D DAW Control
Adjusts the level of the signal received from Cubase AI
sent to the AUDIOGRAM STEREO OUT jacks
3.
E MASTER LEVEL Control
Adjusts the signal level sent to the STEREO OUT jacks
3. This allows you to adjust the overall volume without
changing the relative volume balance among the chan-
nels.
F USB Connector
Connects the AUDIOGRAM interface to a USB port on
your computer via the supplied USB cable. In addition
to transferring audio data between the AUDIOGRAM
interface and the computer, the USB cable supplies
power from the computer to the AUDIOGRAM interface.
When connecting or disconnecting the USB
cable be sure to turn the DAW control and the
MASTER LEVEL control all the way down.
Yamaha recommends that you use a USB
cable with a length of 1.5 meter or less.
Input Signal Flow
NOTE
CAUTION
CAUTION
NOTE
Input
Output
Adjust for maxi-
mum level with
minimum noise.
Compress the sig-
nal for increased
subjective level.
Adjust the recording level
as well as the balance
between channels.
Adjusts the
monitor level.
Adjusts the playback
level from Cubase AI
(does not affect the
record level).
Record
Playback
E MASTER
LEVEL control
D DAW
control
0 LEVEL
controls
7 COMP
controls
6 GAIN
controls
C Level
indicator
Cubase AI
17
AUDIOGRAM 6 Owner’s Manual
Troubleshooting
The AUDIOGRAM interface won’t turn on.
Is the included USB cable properly plugged into the
interface and a computer?
The system doesn’t work properly.
Are the USB cable and all necessary audio cables
properly connected?
Are you using a USB hub?
USB hubs can interfere with proper operation, so try
connecting the AUDIOGRAM interface directly to a
USB port on the computer. If the computer has multi-
ple USB ports, try a different USB port.
Are you using other USB devices at the same time?
If so, try removing the other device(s) and connecting
only the Yamaha USB device.
The Input ports are not shown (Windows 7/Vista)
Is the sound input of your computer operating system
assigned properly?
1. From the [START] menu click [Control Panel],
then double-click the “Sound” icon to open the
“Sound” dialog window.
2. Click the “Recording” tab, right-click the “USB
Audio CODEC” icon and select “Properties.”
3. Click the “Advanced” tab, then select “2 channel, 16
bit, 44100 Hz (CD Quality)” or “2 channel, 16 bit,
48000 Hz (DVD Quality)” in the “Default Format”
field.
No sound.
Are your speaker cables connected properly, or are
they shorted?
Are the volume controls of your sources, audio
devices, applications software, computer operating
system, etc., set at appropriate levels?
Is the output of your computer operating system
muted?
Do you have several applications running at the
same time?
Be sure to quit all applications you are not using.
Is the sound output of your computer operating sys-
tem assigned properly?
Windows 7/Vista:
1. From the [START] menu click [Control Panel],
then double-click the “Sound” icon to open the
“Sound” dialog window.
2. Click the “Playback” tab and check whether the
“USB Audio CODEC” icon is checked.
If not, right-click the “USB Audio CODEC” icon and
select “Set as Default Device.”
3. Click the [Recording] tab and check whether the
“USB Audio CODEC” icon is checked.
If not, right-click the “USB Audio CODEC” icon and
select “Set as Default Device.”
Windows XP:
1. From the [START] menu click [Control Panel],
then double-click the “Sounds and Audio Devices”
icon to open the “Sounds and Audio Devices Prop-
erties” dialog window.
2. Click the “Audio” tab.
3. Set “Sound playback: Default device” and “Sound
recording: Default device” to “USB Audio CODEC.”
4. Click [OK].
Mac:
1. Select “System Preferences ...” from the Apple
menu and then select “Sound” to open the “Sound”
dialog window.
2. Click the “Input” tab and under “Choose a device
for sound input” select “USB Audio CODEC”.
3. Click the “Output” tab and under “Choose a device
for sound output” select “USB Audio CODEC”.
Is the sound output of the Cubase AI application
assigned properly?
For setup details refer to page 8 of the Quick Guide.
The recorded sound is too low in level.
Is the computer’s output level setting too low?
We recommend that you set the computer output to
the maximum level and mute the computer’s internal
speaker.
Windows 7/Vista:
1. From the [START] menu click [Control Panel],
then double-click the “Sound” icon to open the
“Sound” dialog window.
2. Click the “Playback” tab, right-click the “USB Audio
CODEC” icon and select “Properties”.
3. Click the “Levels” tab, then set the volume slider to
its maximum level.
Close the “Properties” dialog window.
4. Click the “Sounds” tab in the “Sound” dialog win-
dow, then select “No sounds” in the “Sound
Scheme.”
Windows XP:
1. From the [START] menu click [Control Panel],
then double-click the “Sounds and Audio Devices”
icon to open the “Sounds and Audio Devices Prop-
erties” dialog window.
2. Click the “Volume” tab.
3. Set “Device volume” to “High.”
4. Click the “Sound” tab.
5. Select “No sound” in the “Sound scheme.”
Troubleshooting
18
AUDIOGRAM 6 Owner’s Manual
Mac:
1. Select [System Preferences ...] from the Apple
menu and then select “Sound” to open the “Sound”
dialog window.
2. Click the “Output” tab and set the volume slider at
the bottom of the window to its maximum level.
3. Click the “Sound Effect” tab and set the volume
slider of the “Alert volume” slider to its minimum
level.
Have you connected or disconnected the USB cable
while Cubase AI is running?
Doing so can sometimes cause the Windows output
level to be reset to its default level. Check and raise
the output level if necessary.
The sound is intermittent or distorted.
Is the PEAK indicator flashing red?
You might have to lower GAIN or LEVEL control lev-
els to avoid distortion.
Are you applying the compressor at an appropriate
level?
You might have to lower COMP control levels.
Are any other applications, device drivers, or USB
devices (scanners, printers, etc.) running at the
same time?
Be sure to quit all applications you are not using.
Are you playing back a large number of audio
tracks?
The number of tracks you can play at the same time
will depend on the performance of the computer you
are using. You may experience intermittent playback
if you exceed your computer’s capabilities.
Are you recording or playing long continuous sec-
tions of audio?
The audio data processing capabilities of your com-
puter will depend on a number of factors including
CPU speed and access to external devices.
On Windows XP computers, changing some settings
as outlined below can improve performance.
1. Click [Control Panel] from the [START] menu, and
double-click the “Sounds and Audio Devices” icon
to open the “Sounds and Audio Devices Proper-
ties” dialog window.
2. Click the “Volume” tab and click “Advanced” in
“Speaker settings.” The “Advanced Audio Proper-
ties” dialog window will open.
3. Click the “Performance” tab. Set “Hardware accel-
eration” to “Full”, and “Sample rate conversion
quality” to “Good.”
Don’t change these settings if you are not familiar
with your computer’s operating system.
Check that the file system is set properly, and make
sure that you have a plenty of free memory (more
than 128 megabytes). If the audio files you are
recording or playing are not too large, changing the
virtual memory settings can sometimes improve
audio performance.
In some cases it might be necessary to update your
hard disk controller, device drivers, or BIOS. Refer to
your computer’s support center or support page on
the web for more information.
Try adding memory.
Adding more RAM memory can significantly increase
your computer’s audio performance. Refer to your
computer’s owner’s manual for information on install-
ing and setting up extra memory.
There is a delay when playing a software synthe-
sizer via a MIDI keyboard (latency).
Check the URL listed below for the latest information.
<http://www.yamahasynth.com/>
104
AUDIOGRAM 6 Owner’s Manual
Specifications
General Specifications
Dimensional Diagrams
Jacks MIC/INST Input Jack x 2 Combo jacks (Mic/HiZ)
LINE Input Jacks (L, R) x 2 Phone jacks
PHONES Jack x 1 Phone jack
STEREO OUT Jacks (L, R) x 1 Phone jacks
USB Connector x 1 USB 1.1 44.1/48 kHz, 16 bit
Controls MIC/INST Switch x 2
MIC: for microphones
INST (Hi-Z): for guitars, etc.
GAIN Control x 4 Gain for CH 1-5/6
COMP Control x 2 Compressor for CH 1, 2
MONO/STEREO Switch x 1
MONO: CH 1, 2 signals fuction as independent mono channels.
STEREO: CH 1, 2 signals fuction as a stereo pair.
LEVEL Control x 4 Adjust the level of CH 1-5/6
PHANTOM +48V Switch x 1 48 V, only for CH1
DAW Control x 1 Adjusts the DAW playback signal
MASTER LEVEL Control x 1 Adjusts the overall signal
Indicators Level Indicators x 1 2 points (green, red)
PEAK Indicator x 4 Red
Phantom Power x 1 Red
Powerx 1 Green
Power Supply USB bus-powered
Dimensions (W x H x D) 170 x 59 x 192 mm
Net Weight 760 g
Included Accessories
Cubase AI DVD-ROM
USB cable
Owner’s Manual
56
51
W: 170
D: 192
3
H: 59
38
Unit: mm
Specifications
105
AUDIOGRAM 6 Owner’s Manual
Block Diagram and Level Diagram
COMBO
COMBO
PHANTOM (+48V)
MIC/INST
Hi-Z
MIC/INST
Hi-Z
HA COMP
COMP
HA
HA
HA
COMP
COMP
Gain
[10 to 54dB]
Gain
[6 to 50dB]
[–6dBu]
[–6dBu]
[–6dBu]
[–6dBu]
[–6dBu]
[–22dBu]
[–22dBu]
Gain
[10 to 54dB]
[–6dBu]
[–6dBu]
PEAK
RE
BA
SUM
SUM
SUM
MASTER
SUM
BA
BA
MUTE
DR
PEAK
SIGNAL
L
L
R
STEREO OUT
[–2dBu]
PHONES
[0.5mW @ 40ohms]
MIC A
[–60 to –16dBu]
MIC B
[–60 to –16dBu]
INST
[–44 to 0dBu]
CH INPUT
(CH1, L)
MIC A
[–60 to –16dBu]
MIC B
[–60 to –16dBu]
INST
[–44 to 0dBu]
CH INPUT
(CH2, R)
R
RE
GR
DR
BA
BA
BA
PEAK
CH Level
ST CH Level
[–6dBu]
[–6dBu] [–6dBu] [–2dBu]
[–20dBu]
[–6dBu][–22dBu] [–20dBu]
[–22dBu]
CH Level
RE
PEAK
RE
MONO/STEREO
[–12dBu]
HA
HA
Gain
[6 to 50dB]
[–6dBu]
[–6dBu]
[–22dBu]
BA
BA
ST CH Level
PEAK
RE
LINE L/MONO
(CH3)
[–34 to +10dBu]
ST CH INPUT
(CH3/4)
LINE R
(CH4)
[–34 to +10dBu]
LINE L/MONO
(CH5)
[–34 to +10dBu]
ST CH INPUT
(CH5/6)
LINE R
(CH6)
[–34 to +10dBu]
USB
REG
USB
AUDIO
LO
RO
LIN
D–
D+
Vbus (+5V)
IN
DC–DC
+5V
GR
DAW
RE
POWER
PHANTOM
+48V
–7.5V
+7.5V
DC–DC
DC–DC
OUT1
OUT2
SW_IC
EN1
EN2
+3.7V
GND
LPF
LPF
LPF
LPF
RIN
12MHz
SSPND
STEREO L
STEREO R
ST CH IN LINE Gain: Max [–34dBu]
ST CH IN LINE Gain: Min [+10dBu]
Clip Level
Clip Level
CH Level
ST CH Level
[Nominal: –16dB]
Clip Level
Clip Level
CH IN MIC Gain: Max [–60dBu]
CH IN INST Gain: Max [–44dBu]
CH IN MIC Gain: Min [–16dBu]
CH IN INST Gain: Max [0dBu]
Clip Level
MASTER
[Nominal: –6dB]
DAW
[Nominal: –16dB]
STEREO OUT [–2dBu]
PHONES [0.5mW @ 40ohms]
+30dBu
+20dBu
+10dBu
0dBu
–10dBu
–20dBu
–30dBu
–40dBu
–50dBu
–60dBu
+30dBu
+20dBu
+10dBu
0dBu
–10dBu
–20dBu
–30dBu
–40dBu
–50dBu
–60dBu
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Yamaha Audiogram6 Instrukcja obsługi

Kategoria
Miksery audio
Typ
Instrukcja obsługi