Indesit XWC 61051 W EU instrukcja

GB

1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Load balancing system

Disposal

Description of the washing machine

and starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Push & Wash

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Troubleshooting, 11

Service, 12

XWC 61051

Instructions for use

WASHING MACHINE

English,1

GB

I

Italiano,13

FR

Français,25

PL

Polski,37

ES

Español,49

PT

Português,61

2

GB

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the inlet

hose by screwing it

to a cold water tap

using a 3/4 gas thre-

aded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the range of values indicated in the Technical

data table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, transferred or moved, make

sure that the instruction manual remains with

the machine so that the new owner is able to

familiarise himself/herself with its operation

and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

GB

3

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drain duct or

a wall drain situated

between 65 and 100

cm from the floor;

alternatively, placed

it over the edge of a

basin, sink or tub, fa-

stening the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• the power supply voltage falls within the va-

lues indicated in the Technical data table (see

opposite);

• the socket is compatible with the plug of the

washing machine. If this is not the case, repla-

ce the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been instal-

led, the electricity socket must remain within

easy reach.

65 - 100 cm

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held re-

sponsible in the event that these standards are

not observed.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle “Auto Clean” (see “Cleaning the

washing machine”).

Technical data

Model

XWC 61051

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 6 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1000 rotations per minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 8:

Cotton Standard 60°.

Programme 9:

Cotton Standard 40°.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

4

GB

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front of

the machine by first

pressing it in the cen-

tre and then pushing

downwards on both

sides until you can re-

move it (see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

• Unplug the washing machine when cleaning it

and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards (2)

(see figure).

Wash it under running

water; this procedure

should be repeated fre-

quently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

2

1

2

3

A

B

GB

5

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

• The washing machine must only be used by adults, in accor-

dance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washing ma-

chine performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

6

GB

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the washing machine on and off.

PUSH & WASH button: (see “Wash cycles”).

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE knob and indicator light: sets the tempe-

rature or the cold wash cycle (see “Personalisation”).

SPIN SPEED knob and indicator light: sets the spin

speed or exclude the spin cycle completely (see “Persona-

lisation”).

WASH CYCLE PROGRESS

indicator light

s: used to

monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem-

porarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash orange,

while the indicator light for the current wash cycle phase

will remain lit in a fixed manner. If the DOOR LOCKED

indicator light is switched off, the door may be opened

(wait approximately 3 minutes).

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine and starting a wash cycle

Control panel

WASH CYCLE PROGRESS

indicator lights

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

FUNCTION

buttons with

indicator lights

PUSH & WASH

button

TEMPERATURE

knob and indicator light

SPIN SPEED

knob and indicator light

GB

7

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to indicate

which phase of the cycle is currently in progress.

Function buttons and corresponding indicator

lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected option is not compatible with another

previously selected option, the indicator light will flash

accompanied by a buzzer (3 beeps), and only the latter

option will be activated; the indicator light corresponding to

the activated option will turn on

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes).

To open the door during a running wash cycle, press the

START/PAUSE button; the door may be opened once the

DOOR LOCKED indicator light turns off.

Starting a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. Turn the washing machine on by pressing the ON/OFF

button. All the indicator lights will turn on for a few secon-

ds, then only the indicator lights relative to the selected

programme settings will remain lit and the START/PAUSE

indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see

“Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE

button and the corresponding indicator light will remain lit

in a fixed manner in green. To cancel the set wash cycle,

pause the machine by pressing the START/PAUSE button

and select a new cycle.

9. At the end of the wash cycle the END indicator light

will switch on. The door can be opened once the DOOR

LOCK indicator light turns off (wait approximately 3 mi-

nutes). Take out your laundry and leave the appliance door

ajar to make sure the drum dries completely. Switch the

washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

END

8

GB

Wash cycles

Table of wash cycles

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 800 rpm. Maximum load 3,5 kg. (Cycle duration 50’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END indicator light turns on.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

1

Sport

30° 600 -

 

- 3,5 - - - 55’

2

Dark

30° 800 -

 

- 4 - - - 70’

3

Anti-odour (Cotton) 60° 1000 -

 

- 3,5 - - - 110’

3

Anti-odour (Synthetic) 40° 1000 -

 

- 3,5 - - - 100’

4

Delicate

30° 0 -

 

- 1 - - - 80’

5

Wool: for wool, cashmere, etc. 40° 800 -

 

- 1,5 - - - 70’

6

Duvet: for down-stuffed garments. 30° 1000 -

 

- 2 - - - 110’

Standard

7

Cottons with Pre-wash: extremely soiled whites. 90° 1000

  

- 6 62 2,15 86 170’

8

Cotton Standard 60° (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1000 -

 

- 6 62 1,05 50 195’

9

Cotton Standard 40° (2): lightly soiled whites and delicate colours.

40° 1000 -

 

- 6 62 0,86 69 180’

10

Synthetic: heavily soiled resistant colours. 60° 800 -

 

- 3,5 46 0,79 46 110’

10

Synthetic (3): lightly soiled resistant colours. 40° 800 -

 

- 3,5 46 0,56 46 100’

11

Coloured

40° 1000 -

 

- 6 62 0,89 70 100’

Eco & Rapid

12

Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1000 -

 

- 6 - - - 170’

13

Eco Synthetic

20° 800 -

 

- 6 - - - 120’

14

Rapid

- 800 - -



- 1,5 - - - 9’

14

Rapid

30° 800 -

 

- 3 80 0,22 34 30’

14

Rapid

60° 1000 -

 

- 6 - - - 60’

Partials

Rinse / Bleach - 1000 - -

 

6 - - - 50’

Spin + Drain - 1000 - - - - 6 - - - 10’

Drain only * - - - - - 6 - - - 3’

* If you select programme and exclude the spin cycle, the machine will drain only.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

GB

9

Setting the temperature

Turning the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash .

N.B.: If the set value is compatible with the selected cycle, the knob indicator will be lit (fixed light). If it isn’t, it will flash and 3

beeps will be heard.

The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value

set for each wash cycle.

! Exception: if the 8 programme is selected, the temperature can be increased up to a value of 90°C.

Setting the spin speed

Turning the SPIN SPEED knobn to set the spin speed for the selected wash cycle.

N.B.: If the set value is compatible with the selected cycle, the knob indicator will be lit (fixed light). If it isn’t, it will flash and 3

beeps will be heard.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1000 rpm

Synthetics 800 rpm

Wool 800 rpm

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed

set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the

selected wash cycle.

Rapid

When this button is pressed the first time, the 9’ icon will light up, when pressed the second time the 30’ icon lights up and

the third time the 60’ icon lights up. When pressed the fourth time the 9’ icon lights up again.

! It cannot be used in conjunction with wash cycles 1-2-3-4-5-6-7-8-9-10-11-12-13- - .

Fast Forward

During a wash programme and under certain conditions, pressing this button allows for ending the wash programme after

only 20’ if necessary, by performing a brief rinse cycle followed by a spin cycle at maximum 800 rpm or lower, if reduced

manually during the programme customisation phase. In this case, washing and rinsing performance will be reduced. After

pressing the button, the relative indicator light turns on together with the indicator light of the rinse phase. If the selected

temperature is equal to 40° and/or the button is pressed during the initial phase of the programme, the “Fast Forward” option

lasts longer so that the detergent can dissolve properly and avoid damaging the fabrics. In this case, the rinse phase indica-

tor light flashes while the wash indicator light remains fixed until the necessary activation conditions are fulfilled. If less than

20’ remain of the wash programme, the option will be disabled.

! It cannot be used in conjunction with wash cycles 2-4-5-6-14- - .

Easy iron

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end

of the cycle the washing machine will perform slow rotations of the drum, while the EASY IRON and START/PAUSE indicator

lights will flash and the END led will remain lit in a fixed manner. To end the cycle, press the START/PAUSE button or the

EASY IRON button.

! It cannot be used in conjunction with wash cycles 1-3-5-14- - .

Extra Rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! It cannot be used in conjunction with wash cycles 2-4-14- .

Personalisation

10

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct dose of

detergent: adding too much detergent will not necessarily result

in a more efficient wash, and may in fact cause build up on the in-

side of your appliance and contribute to environmental pollution.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispenser

drawer and pour in the detergent

or washing additive, as follows.

Compartment 1: Pre-wash

detergent (powder)

Before pouring in the detergent,

make sure that extra compart-

ment 4 has been removed.

Compartment 2: Washing

detergent (powder or liquid)

If liquid detergent is used, it is

recommended that the removable plastic partition A (supplied)

be used for proper dosage. If powder detergent is used, place

the partition into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into compartment

1. In pouring the bleach do not exceed the “max” level indicated

on the central pin.

Perform bleaching by pouring the bleach into additional com-

partment 4 and set the programme .

! Traditional bleach should be used on resistant white fabrics, and

delicate bleach for coloured and synthetics fabrics and for wool.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash cycles”,

which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Garments requiring special care

Sport (programme 1) is designed for washing lightly soiled sports

clothing (tracksuits, shorts, etc.); for best results, we recommend

not exceeding the maximum load indicated in the “Programme

table”. We recommend using liquid detergent, and adding the

amount suitable for a half-load.

Dark: use cycle 2 to wash dark-coloured garments. This pro-

gramme is designed to maintain dark colours over time. We

recommend using a liquid detergent for the best results when

washing dark-coloured garments.

Anti-odour: use programme 3 for washing garments with bad

odours (e.g. smoke, sweat, fried food). The programme is de-

signed to remove bad odours while preserving the fabric fibres.

Synthetics fabrics or mixed loads should be washed at 40°, and

resistant cotton fabrics at 60°.

Delicate: use programme 4 to wash very delicate garments.

It is advisable to turn the garments inside out before washing

them. For best results, use liquid detergent on delicate garments.

For washing Silk items and Curtains, select the relevant cycle 4

and activate the option (in this case it will also be possible

to enable the “Extra Rinse” option); the machine will end the

cycle with the laundry soaked and the indicator light will flash.

To drain the water so that the laundry can be removed, press

the START/PAUSE button or the option .

Wool: the wool wash programme of this machine has been tested

and approved by The Woolmark Company for the washing of

wool containing garments labelled as “hand wash” provided that

the garments are washed according to the instructions on the

garment label and those issued by the manufacturer of this

washing machine. (M1126)

In UK, Eire, Hong Kong and India the Woolmark trade mark is a

Certification trade mark.

Duvet: to wash single duvets (the weight of which should not

exceed 2 kg), cushions or clothes padded with goose down

such as puffa jackets, use the special wash cycle number 6.

We recommend that duvets are placed in the drum with their

edges folded inwards (see figure) and that no more than ¾ of

the total volume of the drum is used. To achieve the best results,

we recommend that a liquid detergent is used and placed inside

the detergent dispenser drawer.

Coloured: use this cycle 11 to wash bright coloured clothes. The

programme is designed to maintain bright colours over time.

Cotton Standard 20° (programme 12) ideal for lightly soiled

cotton loads. The effective performance levels achieved at cold

temperatures, which are comparable to washing at 40°, are

guaranteed by a mechanical action which operates at varying

speed, with repeated and frequent peaks.

Eco Synthetic (programme 13) ideal for mixed loads (cotton and

synthetics) with a normal soil level. The effective performance levels

achieved at cold temperatures are guaranteed by a mechanical

action which operates at varying speed, across set average intervals.

Rapid (programme 14) allows for varying the garment treatment

duration from 9’ to 60’. Pressing the corresponding “Rapid” button

allows for varying the cycle duration between 9’ (refresh), 30’ (wash),

60’ (wash). The 9’ cycle refreshes garments using fabric softener only;

it is advisable not to add any detergent into the machine. The 30’

cycle is designed to wash lightly soiled garments at 30° (excluding

wool and silk) with a 3 kg maximum load in a short time: it only lasts

30 minutes and allows for saving time and energy. The 60’ cycle is

designed to wash moderately soiled resistant cotton garments at 60°

in an hour, with good washing performance. For synthetic or mixed

garments, we recommend lowering the temperature down to 40°.

1

2

3

4

A

B

GB

11

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The washing machine continuously

takes in and drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The “Functions” indicator lights and the

“start/pause” indicator light flash, while

one of the “phase in progress” indicator

lights and the “door locked” indicator

light will remain lit in a fixed manner.

There is too much foam.

Push & Wash does not activate.

The programme lasts a lot less that

expected.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The option function is enabled: to complete the wash cycle, press the

START/PAUSE button (“Personalisation”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

• After switching on the machine a control other than Push & Wash was activa-

ted. Switch the machine off and press the Push & Wash button.

• The “Fast Forward” option was activated.

12

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

13

I

Italiano

Sommario

Installazione, 14-15

Disimballo e livellamento

Collegamenti idraulici ed elettrici

Primo ciclo di lavaggio

Dati tecnici

Manutenzione e cura, 16

Escludere acqua e corrente elettrica

Pulire la lavabiancheria

Pulire il cassetto dei detersivi

Curare oblò e cestello

Pulire la pompa

Controllare il tubo di alimentazione dell’acqua

Precauzioni e consigli, 17

Sicurezza generale

Sistema bilanciamento del carico

Smaltimento

Descrizione della lavabiancheria e

avviare un programma, 18-19

Pannello di controllo

Spie

Avviare un programma

Programmi, 20

Push & Wash

Tabella dei programmi

Personalizzazioni, 21

Impostare la temperatura

Impostare la centrifuga

Opzioni

Detersivi e biancheria, 22

Cassetto dei detersivi

Ciclo candeggio

Preparare la biancheria

Capi particolari

Anomalie e rimedi, 23

Assistenza, 24

Assistenza Attiva 7 giorni su 7

I

LAVABIANCHERIA

XWC 61051

Istruzioni per l’uso

14

I

! È importante conservare questo libretto per

poterlo consultare in ogni momento. In caso di

vendita, di cessione o di trasloco, assicurarsi che

resti insieme alla lavabiancheria per informare il

nuovo proprietario sul funzionamento e sui relativi

avvertimenti.

! Leggere attentamente le istruzioni: ci sono

importanti informazioni sull’installazione, sull’uso

e sulla sicurezza.

Disimballo e livellamento

Disimballo

1. Disimballare la lavabiancheria.

2. Controllare che la lavabiancheria non abbia

subìto danni nel trasporto. Se fosse danneggiata

non collegarla e contattare il rivenditore.

3. Rimuovere le 4 viti di

protezione per il traspor-

to e il gommino con il

relativo distanziale, posti

nella parte posteriore

(vedi figura).

4. Chiudere i fori con i tappi di plastica in dota-

zione.

5. Conservare tutti i pezzi: qualora la lavabianche-

ria debba essere trasportata, dovranno essere

rimontati.

! Gli imballaggi non sono giocattoli per bambini.

Livellamento

1. Installare la lavabiancheria su un pavimento pia-

no e rigido, senza appoggiarla a muri, mobili o altro.

2. Se il pavimento non

fosse perfettamente

orizzontale, compensa-

re le irregolarità svitando

o avvitando i piedini

anteriori (vedi figura);

l’angolo di inclinazione,

misurato sul piano di

lavoro, non deve supe-

rare i 2°.

Un accurato livellamento dà stabilità alla mac-

china ed evita vibrazioni, rumori e spostamenti

durante il funzionamento. In caso di moquette

o di un tappeto, regolare i piedini in modo da

conservare sotto la lavabiancheria uno spazio

sufficiente per la ventilazione.

Collegamenti idraulici ed elettrici

Collegamento del tubo di alimentazione

dell’acqua

1. Collegare il tubo

di alimentazione avvi-

tandolo a un rubinetto

d’acqua fredda con

bocca filettata da 3/4

gas (vedi figura).

Prima di allacciare,

far scorrere l’acqua

finché non sia limpida.

2. Collegare il tubo

di alimentazione alla

lavabiancheria

avvitandolo all’appo-

sita presa d’acqua,

nella parte posteriore

in alto a destra (vedi

figura).

3. Fare attenzione che nel tubo non ci siano né

pieghe né strozzature.

! La pressione idrica del rubinetto deve essere

compresa nei valori della tabella Dati tecnici

(vedi pagina a fianco).

! Se la lunghezza del tubo di alimentazione

non fosse sufficiente, rivolgersi a un negozio

specializzato o a un tecnico autorizzato.

! Non utilizzare mai tubi già usati.

! Utilizzare quelli in dotazione alla macchina.

Installazione

15

I

Collegamento del tubo di scarico

Collegare il tubo di

scarico, senza pie-

garlo, a una condut-

tura di scarico o a

uno scarico a muro

posti tra 65 e 100

cm da terra;

oppure appoggiarlo

al bordo di un lavan-

dino o di una vasca,

legando la guida in

dotazione al

rubinetto (vedi figu-

ra). L’estremità libera

del tubo di scarico

non deve rimanere

immersa nell’acqua.

! È sconsigliato usare tubi di prolunga; se in-

dispensabile, la prolunga deve avere lo stes-

so diametro del tubo originale e non superare

i 150 cm.

Collegamento elettrico

Prima di inserire la spina nella presa della cor-

rente, accertarsi che:

• la presa abbia la messa a terra e sia a norma

di legge;

• la presa sia in grado di sopportare il carico

massimo di potenza della macchina, indicato

nella tabella Dati tecnici (vedi a fianco);

• la tensione di alimentazione sia compresa nei va-

lori indicati nella tabella Dati tecnici (vedi a fianco);

• la presa sia compatibile con la spina della

lavabiancheria. In caso contrario sostituire

la presa o la spina.

! La lavabiancheria non va installata all’aperto,

nemmeno se lo spazio è riparato, perché è molto

pericoloso lasciarla esposta a pioggia e temporali.

! A lavabiancheria installata, la presa della

corrente deve essere facilmente raggiungibile.

! Non usare prolunghe e multiple.

! Il cavo non deve subire piegature o compressioni.

! Il cavo di alimentazione deve essere sostituito

solo da tecnici autorizzati.

Attenzione! L’azienda declina ogni responsabilità

qualora queste norme non vengano rispettate.

Primo ciclo di lavaggio

Dopo l’installazione, prima dell’uso, effettuare

un ciclo di lavaggio con detersivo e senza bian-

cheria impostando il programma “Auto Pulizia”

(vedi “Pulire la lavabiancheria”).

65 - 100 cm

Dati tecnici

Modello

XWC 61051

Dimensioni

larghezza cm 59,5

altezza cm 85

profondità cm 54

Capacità

da 1 a 6 kg

Collega-

menti elet-

trici

Vedi targhetta caratteristi-

che tecniche applicata sulla

macchina

Collega-

menti idrici

pressione massima

1 MPa (10 bar)

pressione minima

0,05 MPa (0,5 bar)

capacità del cesto 52 litri

Velocità di

centrifuga

sino a 1000 giri al minuto

Programmi

di

controllo

secondo

la direttive

1061/2010 e

1015/2010

programma 8;

Cotone Standard 60°C.

programma 9;

Cotone Standard 40°C.

Questa apparecchiatura è

conforme alle seguenti Diret-

tive Comunitarie:

- 2004/108/CE (Compatibili-

tà Elettromagnetica)

- 2006/95/CE (Bassa Tensione)

- 2012/19/EU

16

I

Manutenzione e cura

Pulire la pompa

La lavabiancheria è dotata di una pompa

autopulente che non ha bisogno di manuten-

zione. Può però succedere che piccoli oggetti

(monete, bottoni) cadano nella precamera che

protegge la pompa, situata nella parte inferiore

di essa.

! Assicurarsi che il ciclo di lavaggio sia terminato

e staccare la spina.

Per accedere alla precamera:

1. rimuovere il pan-

nello di copertura sul

lato anteriore della

macchina premendo

verso il centro, quin-

di spingere verso il

basso da entrambe

i lati ed estrarlo (vedi

figure).

2. svitare il coperchio

ruotandolo in senso

antiorario (vedi figura):

è normale che fuorie-

sca un po’ d’acqua;

3. pulire accuratamente l’interno;

4. riavvitare il coperchio;

5. rimontare il pannello assicurandosi, prima di

spingerlo verso la macchina, di aver inserito i

ganci nelle apposite asole.

Controllare il tubo di alimentazio-

ne dell’acqua

Controllare il tubo di alimentazione almeno

una volta all’anno. Se presenta screpolature e

fessure va sostituito: durante i lavaggi le forti

pressioni potrebbero provocare improvvise

spaccature.

! Non utilizzare mai tubi già usati.

Escludere acqua e corrente elettrica

• Chiudere il rubinetto dell’acqua dopo ogni lavaggio.

Si limita così l’usura dell’impianto idraulico della

lavabiancheria e si elimina il pericolo di perdite.

•Staccare la spina della corrente quando si

pulisce la lavabiancheria e durante i lavori di

manutenzione.

Pulire la lavabiancheria

• La parte esterna e le parti in gomma possono

essere puliti con un panno imbevuto di acqua

tiepida e sapone. Non usare solventi o abrasivi.

• La lavabiancheria è dotata di un programma

di “Auto Pulizia” delle parti interne che deve

essere effettuato senza alcun tipo di carico

nel cesto.

Il detersivo (nella quantità pari al 10% di quella

consigliata per capi poco sporchi) o additi-

vi specifici per la pulizia della lavabiancheria,

potranno essere utilizzati come coadiuvanti nel

programma di lavaggio. Si consiglia di effettuare

il programma di pulizia ogni 40 cicli di lavaggio.

Per attivare il programma premere contempora-

neamente i tasti A e B per 5 sec. (vedi figura).

Il programma partirà automaticamente ed avrà

una durata di circa 70 minuti. Per fermare il ciclo

premere il tasto START/PAUSE.

Pulire il cassetto dei detersivi

Per estrarre il cassetto

premere la leva (1) e tirarlo

verso l’esterno (2) (vedi

figura).

Lavarlo sotto l’acqua

corrente; questa

pulizia va effettuata

frequentemente.

Curare oblò e cestello

• Lasciare sempre socchiuso l’oblò per evitare

che si formino cattivi odori.

1

2

3

A

B

2

1

17

I

Precauzioni e consigli

! La lavabiancheria è stata progettata e costruita in

conformità alle norme internazionali di sicurezza. Queste

avvertenze sono fornite per ragioni di

sicurezza e devono essere lette attentamente.

Sicurezza generale

• Questo apparecchio è stato concepito esclusivamente

per un uso di tipo domestico.

•Questo apparecchio può essere usato da

bambini da 8 anni in su e da persone con

capacità fisiche, sensoriali o mentali ridotte

o con esperienza e conoscenze insufficienti

se sono supervisionati o se hanno ricevu-

to adeguata formazione in merito all’uso

dell’apparecchio in modo sicuro e capendo

i pericoli connessi. I bambini non devono

giocare con l’apparecchio. Manutenzione

e pulizia non devono essere effettuati dai

bambini senza supervisione.

• Non toccare la macchina a piedi nudi o con le mani o i

piedi bagnati o umidi.

• Non staccare la spina dalla presa della corrente tirando

il cavo, bensì afferrando la spina.

• Non aprire il cassetto dei detersivi mentre la macchina

è in funzione.

• Non toccare l’acqua di scarico, che può raggiungere

temperature elevate.

• Non forzare in nessun caso l’oblò: potrebbe danneg-

giarsi il meccanismo di sicurezza che protegge da

aperture accidentali.

• In caso di guasto, in nessun caso accedere ai mecca-

nismi interni per tentare una riparazione.

• Controllare sempre che i bambini non si avvicinino alla

macchina in funzione.

• Durante il lavaggio l’oblò tende a scaldarsi.

• Se dev’essere spostata, lavorare in due o tre persone

con la massima attenzione. Mai da soli perché la mac-

china è molto pesante.

• Prima di introdurre la biancheria controlla che il cestello

sia vuoto.

Sistema bilanciamento del carico

Prima di ogni centrifuga, per evitare vibrazioni eccessive e

per distribuire il carico in modo uniforme, il cestello effettua

delle rotazioni ad una velocità leggermente superiore

a quella del lavaggio. Se al termine di ripetuti tentativi

il carico non fosse ancora correttamente bilanciato la

macchina effettua la centrifuga ad una velocità inferiore a

quella prevista. In presenza di eccessivo sbilanciamento

la lavabiancheria effettua la distribuzione anzichè la

centrifuga. Per favorire una migliore distribuzione del carico

e il suo corretto bilanciamento si consiglia di mescolare

capi grandi e piccoli.

Smaltimento

•Smaltimento del materiale di imballaggio:

attenersi alle norme locali, così gli imballaggi potranno

essere riutilizzati.

•La direttiva Europea 2012/19/EU sui rifiuti di apparecchia-

ture elettriche ed elettroniche, prevede che gli elettrodo-

mestici non debbano essere smaltiti nel normale flusso dei

rifiuti solidi urbani. Gli apparecchi dismessi devono essere

raccolti separatamente per ottimizzare il tasso di recupero

e riciclaggio dei materiali che li compongono ed impedire

potenziali danni per la salute e l’ambiente.

Il simbolo del cestino barrato è riportato su tutti i prodotti per

ricordare gli obblighi di raccolta separata.

Per ulteriori informazioni, sulla corretta dismissione degli

elettrodomestici, i detentori potranno rivolgersi al servizio

pubblico preposto o ai rivenditori.

18

I

Pannello di controllo

Descrizione della lavabiancheria e

avviare un programma

Cassetto dei detersivi: per caricare detersivi e additivi

(vedi “Detersivi e biancheria”).

Tasto ON/OFF: per accendere e spegnere la lavabiancheria.

Tasto PUSH & WASH: (vedi “Programmi”).

Manopola PROGRAMMI: per impostare i programmi. Du-

rante il programma la manopola resterà ferma.

Tasti e spie OPZIONI: per selezionare le opzioni disponibili.

La spia relativa all’opzione selezionata rimarrà accesa.

Manopola e spia TEMPERATURA: per impostare la tempe-

ratura o il lavaggio a freddo (vedi “Personalizzazioni”).

Manopola e spia CENTRIFUGA: per impostare la centrifu-

ga o escluderla (vedi “Personalizzazioni”).

SPIE AVANZAMENTO CICLO: per seguire lo stato di

avanzamento del programma di lavaggio.

La spia accesa indica la fase in corso.

Spia OBLÒ BLOCCATO: per capire se l’oblò è apribile

(vedi pagina a fianco).

Tasto e spia START/PAUSE: per avviare i programmi o

interromperli momentaneamente.

N.B.: per mettere in pausa il lavaggio in corso, premere

questo tasto, la spia relativa lampeggerà con colore

ambra mentre quella della fase in corso sarà accesa fissa.

Se la spia OBLÒ BLOCCATO sarà spenta, si potrà

aprire l’oblò (attendere 3 minuti circa).

Per far ripartire il lavaggio dal punto in cui è stato

interrotto, premere nuovamente questo tasto.

Modalità stand by

Questa lavatrice, in conformità alle nuove normative

legate al risparmio energetico, è dotata di un sistema

di autospegnimento (stand by) che entra in funzione

dopo circa 30 minuti nel caso di non utilizzo. Premere

brevemente il tasto ON-OFF e attendere che la macchina

si riattivi.

Spia

OBLÒ

BLOCCATO

MANOPOLA

PROGRAMMI

Cassetto dei detersivi

Tasto

ON/OFF

Tasto e spia

START/PAUSE

Tasti e spie

OPZIONE

Tasto

PUSH & WASH

SPIE AVANZAMENTO

CICLO

Manopola e spia

TEMPERATURA

Manopola e spia

CENTRIFUGA

19

I

Spia oblò bloccato

La spia accesa indica che l’oblò è bloccato per impedire

l’apertura; per aprire l’oblò è necessario che la spia sia

spenta (attendere 3 minuti circa).

Per aprire l’oblò mentre un ciclo è in corso premere il

pulsante START/PAUSE; se la spia OBLÒ BLOCCATO è

spenta sarà possibile aprire l’oblò.

Spie

Le spie forniscono informazioni importanti.

Ecco che cosa dicono:

Spie fase in corso

Una volta selezionato e avviato il ciclo di lavaggio desi-

derato, le spie si accenderanno progressivamente per

indicarne lo stato di avanzamento.

Tasti opzione e relative spie

Selezionando un’opzione la spia relativa si illuminerà.

Se l’opzione selezionata non è compatibile con il program-

ma impostato la spia relativa lampeggerà e l’opzione non

verrà attivata.

Se l’opzione selezionata non è compatibile con un’al-

tra precedentemente impostata, l’incompatibilità verrà

segnalata con il lampeggio della spia ed un segnale

acustico (3 beep) e verrà attivata solo la seconda, la spia

dell’opzione attivata si illuminerà.

Avviare un programma

Programmazione rapida

1. CARICARE LA BIANCHERIA.

Aprire la porta oblò. Caricare la biancheria facendo

attenzione a non superare la quantità di carico indicata

nella tabella programmi della pagina seguente.

2. DOSARE IL DETERSIVO.

Estrarre il cassetto e versare il detersivo nelle apposite

vaschette come spiegato in “Detersivi e biancheria”.

3. CHIUDERE L’OBLO’.

4. Premere il tasto PUSH & WASH per avviare il

programma di lavaggio.

Programmazione tradizionale

1. Accendere la lavabiancheria premendo il tasto

ON/OFF. Tutte le spie si accenderanno per qualche

secondo, poi rimarranno accese le spie ralative alle

impostazioni del programma selezionato e pulserà la spia

START/PAUSE.

2. Caricare la biancheria e chiudere l’oblò.

3. Impostare con la manopola PROGRAMMI il programma

desiderato.

4. Impostare la temperatura di lavaggio (vedi “Personalizza-

zioni”).

5. Impostare la velocità di centrifuga (vedi “Personalizzazioni”).

6. Versare detersivo e additivi (vedi “Detersivi e biancheria”).

7. Selezionare le opzioni desiderate.

8. Avviare il programma premendo il tasto START/PAUSE e

la spia relativa rimarrà accesa fissa di colore verde.

Per annullare il ciclo impostato mettere la macchina in pausa

premendo il tasto START/PAUSE e scegliere un nuovo ciclo.

9. Al termine del programma si illuminerà la spia END. Quan-

do la spia OBLO’ BLOCCATO si spegnerà sarà possibile

aprire l’oblò (attendere 3 minuti circa). Estrarre la biancheria e

lasciare l’oblò socchiuso per far asciugare il cestello. Spegne-

re la lavabiancheria premendo il tasto ON/OFF.

Lavaggio

Risciacquo

Centrifuga

Scarico

Fine lavaggio

END

20

I

Programmi

Tabella dei programmi

Push & Wash

Questa funzione permette di avviare un ciclo di lavaggio anche a macchina spenta senza dover preventivamente premere il

tasto ON/OFF o, successivamente all’accensione della macchina, senza aver azionato nessun ulteriore tasto e/o manopola

(diversamente il programma Push & Wash sarà disattivato). Per avviare il ciclo Push & Wash tenere premuto il pulsante per 2

secondi. La spia accesa indica che il ciclo è avviato. Il ciclo di lavaggio è ideale per capi in cotone e sintetici funzionando ad

una temperatura di lavaggio di 30° e una velocità massima di centrifuga pari a 800 giri al minuto. Carico max. 3,5 kg. (Durata

ciclo 50’).

Come funziona?

1. Caricare la biancheria (capi in cotone e/o sintetici) e chiudere l’oblò.

2. Versare detersivo e additivi.

3. Avviare il programma tenendo premuto per 2 secondi il tasto Push & Wash. La spia relativa si illuminerà di colore verde e

l’oblò si bloccherà (simbolo oblò bloccato acceso).

N.B.: L’avvio del lavaggio attraverso il tasto Push & Wash attiva un ciclo automatico consigliato per cotone e sintetici non

personalizzabile. Tale programma non permette la possibilità di impostare ulteriori opzioni.

Per aprire la porta mentre il ciclo automatico è in corso premere il tasto START/PAUSE; se il simbolo oblò bloccato è spento

sarà possibile aprire l’oblò. Premere nuovamente il tasto START/PAUSE per far ripartire il programma dal punto in cui era

stato interrotto.

4. Al termine del programma si illuminerà la spia END.

Programmi

Descrizione del Programma

Temp.

max.

(°C)

Velocità

max.

(giri al

minuto)

Detersivi

Carico max.

(Kg)

Umidità residua %

Consumo energia

kWh

Acqua totale lt

Durata ciclo

Prelavag-

gio

Lavaggio

Ammorbi-

dente

Candeg-

gio

Speciali

1

Sport

30° 600

-

 

-

3,5 - - - 55’

2

Scuri

30° 800

-

 

-

4 - - - 70’

3

Anti Odore (Cotone) 60° 1000

-

 

-

3,5 - - - 110’

3

Anti Odore (Sintetici) 40° 1000

-

 

-

3,5 - - - 100’

4

Delicati

30° 0

-

 

-

1 - - - 80’

5

Lana: per lana, cachemire, ecc.. 40° 800

-

 

-

1,5 - - - 70’

6

Piumini: per capi imbottiti in piuma d’oca. 30° 1000

-

 

-

2 - - - 110’

Standard

7

Cotone 90° + P: bianchi estremamente sporchi. 90° 1000

  

-

6 62 2,15 86 170’

8

Cotone Standard 60° (1): bianchi e colorati resistenti molto sporchi.

60°

(Max. 90°)

1000

-

  

6 62 1,05 50 195’

9

Cotone Standard 40° (2): bianchi poco sporchi e colori delicati.

40° 1000

-

  

6 62 0,86 69 180’

10

Sintetici: colori resistenti molto sporchi. 60° 800

-

  

3,5 46 0,79 46 110’

10

Sintetici (3): colori delicati poco sporchi. 40° 800

-

  

3,5 46 0,56 46 100’

11

Colorati

40° 1000

-

  

6 62 0,89 70 100’

Eco & Rapidi

12

Cotone Standard 20°: bianchi poco sporchi e colori delicati. 20° 1000

-

  

6 - - - 170’

13

Eco Sintetici

20° 800

-

  

6 - - - 120’

14

Rapidi

- 800

- -



-

1,5 - - - 9’

14

Rapidi

30° 800

-

 

-

3 80 0,22 34 30’

14

Rapidi

60° 1000

-

 

-

6 - - - 60’

Parziali

Risciacquo - 1000

- -

 

6 - - - 50’

Centrifuga + Scarico - 1000

- - - -

6 - - - 10’

Solo scarico * -

- - - -

6 - - - 3’

* Selezionando il programma ed escludendo la centrifuga la macchina effettuerà solo lo scarico.

La durata del ciclo indicata sul display o sul libretto è una stima calcolata in base a condizioni standard. Il tempo effettivo può variare in base a numerosi fattori quali tem-

peratura e pressione dell’acqua in ingresso, temperatura ambiente, quantità di detersivo, quantità e tipo di carico, bilanciamento del carico, opzioni aggiuntive selezionate.

1) Programma di controllo secondo la direttiva 1061/2010: impostare il programma 8 con una temperaura di 60°C.

Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su capi lavabili

a 60 °C. La temperatura effettiva di lavaggio può differire da quella indicata.

2) Programma di controllo secondo la direttiva 1061/2010: impostare il programma 9 con una temperaura di 40°C.

Questo ciclo è adatto per pulire un carico di cotone normalmente sporco ed è il più efficiente in termini di consumo combinato di energia e di acqua, da usare su capi lavabili

a 40 °C. La temperatura effettiva di lavaggio può differire da quella indicata.

Per tutti Test Institutes:

2) Programma cotone lungo: impostare il programma 9 con una temperatura di 40°C.

3) Programma sintetico lungo: impostare il programma 10 con una temperatura di 40°C.

Strona jest ładowana ...

Indesit XWC 61051 W EU instrukcja

Indesit XWC 61051 W EU instrukcja

w innych językach

Inne dokumenty