Zebra LI3608 Skrócona instrukcja obsługi

Marka: Zebra

Model: LI3608

Typ: Skrócona instrukcja obsługi

LI3608

Quick Start Guide

Linear Imager Scanner

2 LI3608 Quick Start Guide

Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not

assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or

application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any

patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or

process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems

contained in Zebra products.

Warranty

For the complete Zebra hardware product warranty statement, go to: www.zebra.com/warranty.

For Australia Only

For Australia Only. This warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road, #05-02/03,

Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia

Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to

be of acceptable quality and the failure does not amount to a major failure.

Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies you may

have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies Corporation at +65

6858 0722. You may also visit our website: www.zebra.com for the most updated warranty terms.

Service Information

If you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem

with the equipment, they will contact the Zebra Global Customer Support Center at: www.zebra.com/support.

For the latest version of this guide go to: www.zebra.com/support.

LI3608 Quick Start Guide 3

Introduction

The LI3608 linear imager combines excellent scanning performance and advanced ergonomics to provide the best

value in a lightweight laser scanner, ensuring comfort and ease of use for extended periods of time.

Features

Accessories

4 LI3608 Quick Start Guide

Cable Attachment

1. Insert cable fully so that the connector is flush with the scanner surface.

2. Loosen metal lock plate screws using a PH1 driver.

3. Slide lock plate to fully locked position.

4. Tighten screw using a PH1 driver (torque: 5 in-lb.).

LI3608 Quick Start Guide 5

Connect Host Interface

USB

The digital scanner automatically detects the host interface type and uses the default setting. If the default (*) does not

meet your requirements, scan another host bar code below.

*USB KEYBOARD (HID)

USB CDC HOST

6 LI3608 Quick Start Guide

USB (continued)

IBM TABLE TOP USB

IBM HAND-HELD USB

SNAPI WITHOUT IMAGING

SNAPI WITH IMAGING

USB OPOS HAND-HELD

SSI OVER USB CDC

SIMPLE COM PORT EMULATION

LI3608 Quick Start Guide 7

RS-232

*STANDARD RS-232

ICL RS-232

NIXDORF RS-232 MODE A

NIXDORF RS-232 MODE B

8 LI3608 Quick Start Guide

RS-232 (continued)

Keyboard Wedge

FUJITSU RS-232

OPOS/JPOS

*IBM AT NOTEBOOK

IBM PC/AT and IBM PC COMPATIBLE

LI3608 Quick Start Guide 9

IBM 46XX

NON-IBM SCANNER EMULATION (PORT 5B)

HAND-HELD SCANNER EMULATION (PORT 9B)

TABLE-TOP SCANNER EMULATION (PORT 17)

10 LI3608 Quick Start Guide

Set Defaults Bar Code

RETURN TO FACTORY DEFAULTS

Enter Key Bar Code (Carriage Return/Line Feed)

Add an Enter key after scanned data.

ADD AN ENTER KEY (CARRIAGE RETURN/LINE FEED)

Tab Key Bar Code

Add a Tab key after scanned data.

ADD A TAB KEY

USB Caps Lock Override

USB - OVERRIDE CAPS LOCK KEY (ENABLE)

*USB - DO NOT OVERRIDE CAPS LOCK KEY (DISABLE)

LI3608 Quick Start Guide 11

Aiming

Cover the entire bar code with the aiming pattern to ensure it is within the field of view.

LI3608-SR

LI3608-ER

LED Indications

Beeper Indications

Indication LED

Hand-Held Scanning

The scanner is on and ready to scan, or no power to the scanner Off

A bar code is successfully decoded Green

Transmission error Red

Hand-Free (Presentation) Scanning

No power to the scanner Off

The scanner is on and ready to scan Green

A bar code is successfully decoded Off momentarily

Transmission error Red

Indication Beeper Sequence

Power up Low/medium/high beep

A bar code is successfully decoded Medium beep

Transmission error detected; data is ignored 4 long low beeps

Successful parameter setting High/low/high/low beep

Correct programming sequence performed High/low beep

Incorrect programming sequence, or

Cancel

bar code scanned Low/high beep

012345

12 LI3608 Quick Start Guide

Troubleshooting

123Scan

123Scan2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup of a scanner via a

bar code or USB cable.

Utility Functionality:

• Device Configuration

• Electronic Programming (USB Cable)

• Programming Bar Code(s)

• Data View – Scan Log (Display Scanned Bar Code Data)

• Access Asset Tracking Information

• Upgrade Firmware and View Release Notes

• Remote Management (SMS Package Generation)

For more information, visit: www.zebra.com/123Scan.

Problem Possible Causes Possible Solutions

Scanner not working. No power to scanner. Check system power.

Scanner is disabled. Ensure that correct host interface

cable is used.

Scanner decoding bar code, but data not

transmitting to host.

Host interface not configured

properly.

Scan appropriate host parameter bar

codes.

Interface cable is loose. Ensure all cable connections are

secure.

Invalid ADF rule. Program the correct ADF rules.

Scanner not decoding bar code. Scanner not programmed for bar

code type.

Ensure scanner is programmed to

read type of bar code being scanned.

Bar code unreadable. Ensure bar code is not defaced; try

scanning test bar code of same bar

code type.

Distance between scanner and

bar code incorrect.

Move scanner closer to, or further

from bar code.

Scanned data incorrectly displayed on

host.

Host interface not configured

properly.

Scan appropriate host parameter bar

codes.

Region improperly configured. Select appropriate country and

language encoding scheme.

LI3608 Quick Start Guide 13

Regulatory Information

This device is approved under Zebra Technologies Corporation.

This guide applies to Model Number: LI3608. All Zebra devices are designed to be compliant with rules and regulations

in locations they are sold and will be labeled as required. Local language translations are available at the following

website: www.zebra.com/support.

Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user’s authority to

operate the equipment.

Health and Safety Recommendations

Ergonomic Recommendations

Caution: In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations

below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company's safety

programs to prevent employee injury.

•

Reduce or eliminate repetitive motion

•

Maintain a natural position

•

Reduce or eliminate excessive force

•

Keep objects that are used frequently within easy reach

•

Perform tasks at correct heights

•

Reduce or eliminate vibration

•

Reduce or eliminate direct pressure

•

Provide adjustable workstations

•

Provide adequate clearance

•

Provide a suitable working environment

•

Improve work procedures.

Laser Devices

Class 2 laser scanners use a low power, visible light diode. As with any very bright light source such as the sun, the

user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be

harmful.

Caution: Use of controls, adjustments, or the performance of procedures other than those specified herein

may result in hazardous laser light exposure.

Labels Read:

1. Laser Light - do not stare into beam Class 2 Laser product.

2. Caution - Class 2 laser light when open. Avoid direct eye exposure.

3. Complies with 21 CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24,

2007, and IEC/EN 60825-1:2014.

LED Safety

Classified as Exempt Risk Group per IEC 62471:2006 (Ed. 1.0); EN 62471:2008.

Max Pulse Duration: 12 ms.

14 LI3608 Quick Start Guide

Radio Frequency Interference Requirements - FCC

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

•

Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements - Canada

CAN ICES-3(B)/NMB-3(B)

Marking and European Economic Area (EEA)

Statement of Compliance

Zebra hereby declares that this device is in compliance with all applicable Directives, 2014/30/EU, 2014/35/EU and

2011/65/EU. The full text of the EU Declaration of Conformity is available at the following internet address:

www.zebra.com/doc.

CAUTION- CLASS 2 LASER LIGHT WHEN OPEN. DO NOT

STARE INTO THE BEAM. ATTENTION- LUMIÉRE LASER

EN CAS D'OUVERTURE. NE PAS REGARDER DANS LE FAISCEAU.

VORSICHT- LASERLICHT KLASSE 2, WENN ABDECKUNG GEÖFFNET.

NICHT IN DEN STRAHL BLICKEN.

ὀ ព㸸ᡴᔰᰦཬ㚄䬱ኻᩀᰦ᭷⃭ග䗀ᑕ໚┤㿶ග᮰

NOTE:

LI3608-SR - Label not applicable.

LI3608 Quick Start Guide 15

Other Countries

Japan (VCCI) - Voluntary Control Council for Interference

Class B ITE

Korea Warning Statement for Class B ITE

Chile

Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a

radiaciones electromagnéticas.

China

www.zebra.com/contact

Ukraine

Eurasian Customs Union

Евразийский Таможенный Союз

Данный продукт соответствует требованиям знака EAC.

16 LI3608 Quick Start Guide

Waste Electrical and Electronic Equipment (WEEE)

Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщ ат на Zebra за рециклиране. За

информация относно връщането на продукти, моля отидете на адрес www.zebra.com/weee.

Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skončení jejich životnosti vrátit společnosti Zebra k recyklaci. Informace o způsobu

vrácení produktu najdete na webové stránce: www.zebra.com/recycling/weee.

Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på:

www.zebra.com/recycling/weee.

Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden.

Informationen zur Rücksendung von Produkten finden Sie unter www.zebra.com/recycling/weee.

Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρ έφονται στην Zebra για ανακύκλωση. Για

περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση www.zebra.com/recycling/weee στο Διαδίκτυο.

English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product,

please go to: www.zebra.com/recycling/weee.

Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados.

Si desea más información sobre cómo devolver un producto, visite: www.zebra.com/recycling/weee.

Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote

tagastamise kohta külastage palun aadressi: www.zebra.com/recycling/weee.

Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja

tuotteen palauttamisesta on osoitteessa www.zebra.com/recycling/weee.

Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus

amples informations sur le retour de produits, consultez : www.zebra.com/recycling/weee.

Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék

visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/recycling/weee.

Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne

il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web:

www.zebra.com/recycling/weee.

Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip

grąžinti gaminį, rasite: www.zebra.com/recycling/weee.

Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu inform

āciju par

produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/recycling/weee.

Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar

tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/recycling/weee.

Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling.

Raadpleeg www.zebra.com/recycling/weee voor meer informatie over het terugzenden van producten.

Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji naleźy zwrócić do firmy Zebra w celu ich utylizacji. Informacje na temat

zwrotu produktów znajdują się na stronie internetowej www.zebra.com/recycling/weee.

Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre

como devolver o produto, visite: www.zebra.com/recycling/weee.

Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru

informaţii despre returnarea produsului, accesaţi: www.zebra.com/recycling/weee.

Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie

informácie o vrátení výrobkov nájdete na: www.zebra.com/recycling/weee.

Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka

obiščite: www.zebra.com/recycling/weee.

Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar

produkten finns på www.zebra.com/recycling/weee.

Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında

bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/recycling/weee.

TURKISH WEEE Statement of Compliance

EEE Yönetmeligine Uygundur