Dell Power Supply 2T227 Instrukcja obsługi

www.dell.com | support.dell.com

Dell™ PowerConnect™ RPS-600

Setup Guide

安装指南

安裝指南

Instalační příručka

Guide d'installation

Setup-Handbuch

Telepítési útmutató

설치 안내서

Instrukcja instalacji

Guia de configuração

Руководство по

установке

Návod na inštaláciu

Navodila za nastavitve

Guía de instalación

Model PowerConnect RPS-600

www.dell.com | support.dell.com

Dell™ PowerConnect™ RPS-600

Setup Guide

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage,

personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of

Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerConnect are trademarks of

Dell Computer Corporation; EMC is the trademark of EMC Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest

in trademarks and trade names other than its own.

December 2002 P/N 2T227 Rev. A02

Contents 3

Contents

Caution: Safety Instructions . . . . . . . . . . . . . . . . . . . . 5

General

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rack Mounting of Systems

. . . . . . . . . . . . . . . . . . . . 7

Modems, Telecommunications, or Local Area

Network Options

. . . . . . . . . . . . . . . . . . . . . . . . . 8

Protecting Against Electrostatic Discharge

. . . . . . . . . . . . 9

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . 10

Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Front Panel Indicators

. . . . . . . . . . . . . . . . . . . . . . . 10

Mounting Instructions

. . . . . . . . . . . . . . . . . . . . . . . 11

Installing the PowerConnect RPS-600 on a Flat Surface

. . . . 11

Installing the PowerConnect RPS-600 in a Rack

. . . . . . . . 11

Technical Information

. . . . . . . . . . . . . . . . . . . . . . . 12

Power Supply Specification

. . . . . . . . . . . . . . . . . . 12

Technical Assistance

. . . . . . . . . . . . . . . . . . . . . . . 13

Regulatory Notices

. . . . . . . . . . . . . . . . . . . . . . . . 14

Limited Warranties and Return Policy

. . . . . . . . . . . . . . 27

Limited Warranty for the U.S.

. . . . . . . . . . . . . . . . . 27

"Total Satisfaction" Return Policy (U.S. Only)

. . . . . . . . . . 31

Limited Warranty Terms for Canada

. . . . . . . . . . . . . . 31

"Total Satisfaction" Return Policy

. . . . . . . . . . . . . . . . 35

Dell Software and Peripherals

. . . . . . . . . . . . . . . . . 36

One-Year End-User Manufacturer Guarantee

(Latin America and the Caribbean Only)

. . . . . . . . . . . . 37

4 Contents

Dell PowerConnect RPS-600 Setup Guide 5

Caution: Safety Instructions

Use the following safety guidelines to ensure your own personal safety and to help protect

your system from potential damage.

General

• Observe and follow service markings. Do not service any product except as explained

in your system documentation. Opening or removing covers that are marked with the

triangular symbol with a lightning bolt may expose you to electrical shock.

Components inside these compartments should be serviced only by a trained service

technician.

• If any of the following conditions occur, unplug the product from the electrical outlet

and replace the part or contact your trained service provider:

– The power cable, extension cable, or plug is damaged.

– An object has fallen into the product.

– The product has been exposed to water.

– The product has been dropped or damaged.

– The product does not operate correctly when you follow the operating

instructions.

• Keep your system away from radiators and heat sources. Also, do not block

cooling vents.

• Do not spill food or liquids on your system components, and never operate the

product in a wet environment. If the system gets wet, see the appropriate section in

your troubleshooting guide or contact your trained service provider.

• Do not push any objects into the openings of your system. Doing so can cause fire or

electric shock by shorting out interior components.

• Use the product only with approved equipment.

• Allow the product to cool before removing covers or touching internal components.

• Operate the product only from the type of external power source indicated on the

electrical ratings label. If you are not sure of the type of power source required,

consult your service provider or local power company.

6 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

• Use only approved power cable(s). If you have not been provided with a power cable

for your system or for any AC-powered option intended for your system, purchase a

power cable that is approved for use in your country. The power cable must be rated

for the product and for the voltage and current marked on the product's electrical

ratings label. The voltage and current rating of the cable should be greater than the

ratings marked on the product.

• To help prevent electric shock, plug the system and peripheral power cables into

properly grounded electrical outlets. These cables are equipped with three-prong

plugs to help ensure proper grounding. Do not use adapter plugs or remove the

grounding prong from a cable. If you must use an extension cable, use a 3-wire cable

with properly grounded plugs.

• Observe extension cable and power strip ratings. Make sure that the total ampere

rating of all products plugged into the extension cable or power strip does not exceed

80 percent of the ampere ratings limit for the extension cable or power strip.

• To help protect your system from sudden, transient increases and decreases in

electrical power, use a surge suppressor, line conditioner, or uninterruptible power

supply (UPS).

• Position system cables and power cables carefully; route cables so that they cannot be

stepped on or tripped over. Be sure that nothing rests on any cables.

• Do not modify power cables or plugs. Consult a licensed electrician or your power

company for site modifications. Always follow your local/national wiring rules.

• When connecting or disconnecting power to hot-pluggable power supplies, if offered

with your system, observe the following guidelines:

– Install the power supply before connecting the power cable to the power supply.

– Unplug the power cable before removing the power supply.

– If the system has multiple sources of power, disconnect power from the system by

unplugging all power cables from the power supplies.

• Move products with care; ensure that all casters and/or stabilizers are firmly

connected to the system. Avoid sudden stops and uneven surfaces.

Caution: Safety Instructions (continued)

Dell PowerConnect RPS-600 Setup Guide 7

Rack Mounting of Systems

Observe the following precautions for rack stability and safety. Also refer to the rack

installation documentation accompanying the system and the rack for specific caution

statements and procedures.

Systems are considered to be components in a rack. Thus, "component" refers to any

system as well as to various peripherals or supporting hardware.

CAUTION: Installing systems in a rack without the front and side stabilizers

installed could cause the rack to tip over, potentially resulting in bodily injury

under certain circumstances. Therefore, always install the stabilizers before

installing components in the rack.

After installing system/components in a rack, never pull more than one

component out of the rack on its slide assemblies at one time. The weight of

more than one extended component could cause the rack to tip over and may

result in serious injury.

NOTE: Your system is safety-certified as a free-standing unit and as a component for use in a Dell™

rack cabinet using the customer rack kit. The installation of your system and rack kit in any other

rack cabinet has not been approved by any safety agencies. It is your responsibility to have the final

combination of system and rack kit in a rack cabinet evaluated for suitability by a certified safety

agency. Dell disclaims all liability and warranties in connection with such combinations.

• System rack kits are intended to be installed in a rack by trained service technicians. If

you install the kit in any other rack, be sure that the rack meets the specifications of a

Dell rack.

CAUTION: Do not move racks by yourself. Due to the height and weight of the

rack, a minimum of two people should accomplish this task.

• Before working on the rack, make sure that the stabilizers are secured to the rack,

extended to the floor, and that the full weight of the rack rests on the floor. Install

front and side stabilizers on a single rack or front stabilizers for joined multiple racks

before working on the rack.

• Always load the rack from the bottom up, and load the heaviest item in the rack first.

• Make sure that the rack is level and stable before extending a component from

the rack.

• Use caution when pressing the component rail release latches and sliding a

component into or out of a rack; the slide rails can pinch your fingers.

Caution: Safety Instructions (continued)

8 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

• After a component is inserted into the rack, carefully extend the rail into a locking

position, and then slide the component into the rack.

• Do not overload the AC supply branch circuit that provides power to the rack. The

total rack load should not exceed 80 percent of the branch circuit rating.

• Ensure that proper airflow is provided to components in the rack.

• Do not step on or stand on any component when servicing other components in

a rack.

CAUTION: A qualified electrician must perform all connections to DC power and

to safety grounds. All electrical wiring must comply with applicable local or

national codes and practices.

CAUTION: Never defeat the ground conductor or operate the equipment in the

absence of a suitably installed ground conductor. Contact the appropriate

electrical inspection authority or an electrician if you are uncertain that

suitable grounding is available.

CAUTION: The system chassis must be positively grounded to the rack cabinet

frame. Do not attempt to connect power to the system until grounding cables

are connected. Completed power and safety ground wiring must be inspected by

a qualified electrical inspector. An energy hazard will exist if the safety ground

cable is omitted or disconnected.

Modems, Telecommunications, or Local Area Network Options

• Do not connect or use a modem during a lightning storm. There may be a risk of

electrical shock from lightning.

• Never connect or use a modem in a wet environment.

• Do not plug a modem or telephone cable into the network interface controller (NIC)

receptacle.

• Disconnect the modem cable before opening a product enclosure, touching or

installing internal components, or touching an uninsulated modem cable or jack.

Caution: Safety Instructions (continued)

Dell PowerConnect RPS-600 Setup Guide 9

When Using Your System

Protecting Against Electrostatic Discharge

NOTICE: Only a certified service technician should perform repairs on your system. Damage

due to servicing that is not authorized by Dell is not covered by your warranty.

Static electricity can harm delicate components inside your system. To prevent static

damage, discharge static electricity from your body before you touch any of the electronic

components, such as the microprocessor. You can do so by periodically touching an

unpainted metal surface on the chassis.

You can also take the following steps to prevent damage from electrostatic discharge

(ESD):

• When unpacking a static-sensitive component from its shipping carton, do not

remove the component from the antistatic packing material until you are ready to

install the component in your system. Just before unwrapping the antistatic

packaging, be sure to discharge static electricity from your body.

• When transporting a sensitive component, first place it in an antistatic container or

packaging.

• Handle all sensitive components in a static-safe area. If possible, use antistatic floor

pads and workbench pads and an antistatic grounding strap.

NOTE: Your system may also include circuit cards or other components that contain batteries. These

batteries must also be disposed of in a battery deposit site. For information about such batteries,

refer to the documentation for the specific card or component.

10 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

Package Contents

Before you install the RPS-600, verify that your package contains the

following items:

• RPS-600 Redundant Power Bank

• Documentation CD

• AC power cord

• Rack mounting kit

• Switch DC power cords (4 each)

Features

The PowerConnect RPS-600 Redundant Power Bank provides four external,

redundant power supplies for your PowerConnect switches, eliminating the

power supply as a single point of failure.

• Supports up to four PowerConnect switches through 12-V DC output

• Dedicated 150-W power supply for up to four connected switches

• Front panel LEDs to display status of individual power supplies

• 1-U, 19-inch rack mountable system

Front Panel Indicators

Dell PowerConnect RPS-600 Setup Guide 11

Mounting Instructions

NOTICE: Before you install the PowerConnect™ RPS-600, consult your

PowerConnect switch User's Guide to confirm that your switch supports the

PowerConnect RPS-600 Redundant Power Bank.

Installing the PowerConnect RPS-600 on a Flat Surface

You can install the RPS-600 on any appropriate level surface that can safely

support the weight of the switches, the RPS-600, and their attached cables.

There must be adequate space around the RPS-600 for ventilation and to

access cable connectors.

To install the RPS-600 on a flat surface:

1 Set the RPS-600 on the flat surface and check for proper ventilation.

NOTICE: Allow at least 2 inches (5.1 cm) on each side for proper ventilation

and 5 inches (12.7 cm) at the back for power-cord clearance.

2

Attach rubber feet on each marked location on the bottom of

the chassis.

The rubber feet are optional, but recommended to keep the unit

from slipping.

Installing the PowerConnect RPS-600 in a Rack

The RPS-600 can be installed in most standard 19-inch racks.

NOTE: For racks that are not prethreaded, cage nuts are provided.

To install the RPS-600 in a rack:

1 Use the supplied screws to attach a mounting bracket to each side of

the RPS-600.

2 Position the RPS-600 in the rack and align the holes in the mounting

bracket with the holes in the rack.

3 Insert and tighten two screws appropriate for your rack through each of

the mounting brackets.

12 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

To operate the RPS-600 after installation:

1 Plug one end of the switch DC power cord into the connector labeled

"RPS" on the back of the switch. Connect the other end of the switch

DC power cord to any available RPS connector on the back of the

RPS-600.

2 Attach the AC power cord to the RPS-600 and to an AC power outlet.

The switch is now using both power supplies simultaneously. You can

monitor the status of the two power supplies through the front panel LEDs

on your PowerConnect switch and the RPS-600.

Technical Information

Power Supply Specification

The PowerConnect RPS-600 contains four independent 150-W power

supplies.

• The dimension of each supply is 4.0 x 7.0 x 1.334 inches

(1.16 x 17.78 x 3.338 cm) (max.).

• Each power supply has a single output of 12 V. The following table

details the characteristics of each power supply.

Dell PowerConnect RPS-600 Setup Guide 13

Technical Assistance

If you need help with a technical problem, Dell is ready to assist you. See

the PowerConnect CD that came with your PowerConnect switch for

information about contacting Dell.

Parameter 12-V Output

Voltage +12.0 VDC

Initial accuracy +/–1%

Minimum current 2 A

Maximum current 13 A

Line regulation +/–1%

Load regulation +/–10%

Noise and ripple 10%, peak to peak

Overshoot 5%

Undershoot 5%

Environmental Specifications

Operating temperature 0º to 40ºC (32º to 104ºF)

Operating relative humidity 8% to 90%

Storage temperature –40º to 80ºC (–40º to 176ºF)

Storage relative humidity 5% to 95% noncondensing

Vibration 10 to 300 Hz, sweep at a constant acceleration

of 1.0 G for a duration of 1 hour for each of the

perpendicular axes X, Y, Z

14 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

Regulatory Notices

Electromagnetic Interference (EMI) is any signal or emission, radiated in

free space or conducted along power or signal leads, that endangers the

functioning of a radio navigation or other safety service or seriously

degrades, obstructs, or repeatedly interrupts a licensed radio

communications service. Radio communications services include but are

not limited to AM/FM commercial broadcast, television, cellular services,

radar, air-traffic control, pager, and Personal Communication Services

(PCS). These licensed services, along with unintentional radiators such as

digital devices, including computer systems, contribute to the

electromagnetic environment.

Electromagnetic Compatibility (EMC) is the ability of items of electronic

equipment to function properly together in the electronic environment.

While this computer system has been designed and determined to be

compliant with regulatory agency limits for EMI, there is no guarantee that

interference will not occur in a particular installation. If this equipment

does cause interference with radio communications services, which can be

determined by turning the equipment off and on, you are encouraged to try

to correct the interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the computer with respect to the receiver.

• Move the computer away from the receiver.

• Plug the computer into a different outlet so that the computer and the

receiver are on different branch circuits.

If necessary, consult a Dell Technical Support representative or an

experienced radio/television technician for additional suggestions.

Dell computer systems are designed, tested, and classified for their

intended electromagnetic environment. These electromagnetic

environment classifications generally refer to the following harmonized

definitions:

• Class A is typically for business or industrial environments.

• Class B is typically for residential environments.

Dell PowerConnect RPS-600 Setup Guide 15

Information Technology Equipment (ITE), including peripherals,

expansion cards, printers, input/output (I/O) devices, monitors, and so on,

that are integrated into or connected to the system should match the

electromagnetic environment classification of the computer system.

A Notice About Shielded Signal Cables: Use only shielded cables for

connecting peripherals to any Dell device to reduce the possibility of

interference with radio communications services. Using shielded cables

ensures that you maintain the appropriate EMC classification for the

intended environment. For parallel printers, a cable is available from Dell.

If you prefer, you can order a cable from Dell on the World Wide Web at

accessories.us.dell.com/sna/category.asp?category_id=4117.

Most Dell computer systems are classified for Class B environments.

However, the inclusion of certain options can change the rating of some

configurations to Class A. To determine the electromagnetic classification

for your system or device, refer to the following sections specific for each

regulatory agency. Each section provides country-specific EMC/EMI or

product safety information.

FCC Notices (U.S. Only)

Most Dell computer systems are classified by the Federal Communications

Commission (FCC) as Class B digital devices. To determine which

classification applies to your computer system, examine all FCC

registration labels located on the bottom, side, or back panel of your

computer, on card-mounting brackets, and on the cards themselves. If any

one of the labels carries a Class A rating, your entire system is considered to

be a Class A digital device. If all labels carry an FCC Class B rating as

distinguished by either an FCC ID number or the FCC logo, ( ), your

system is considered to be a Class B digital device.

Once you have determined your system’s FCC classification, read the

appropriate FCC notice. Note that FCC regulations provide that changes

or modifications not expressly approved by Dell could void your authority to

operate this equipment.

16 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including

interference that may cause undesired operation.

Class A

This equipment has been tested and found to comply with the limits for a

Class A digital device pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the manufacturer’s instruction

manual, may cause harmful interference with radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case you will be required to correct the interference at

your own expense.

Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the

manufacturer’s instruction manual, may cause interference with radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, you are encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/television technician

for help.

Dell PowerConnect RPS-600 Setup Guide 17

The following information is provided on the device or devices covered in

this document in compliance with FCC regulations:

• Model number: Dell PowerConnect RPS-600

• Company name:

Dell Computer Corporation

One Dell Way

Round Rock, Texas 78682 USA

512-338-4400

IC Notice (Canada Only)

Most Dell computer systems (and other Dell digital apparatus) are

classified by the Industry Canada (IC) Interference-Causing Equipment

Standard #3 (ICES-003) as Class B digital devices. To determine which

classification (Class A or B) applies to your computer system (or other Dell

digital apparatus), examine all registration labels located on the bottom,

side, or the back panel of your computer (or other digital apparatus). A

statement in the form of "IC Class A ICES-003" or "IC Class B ICES-003"

will be located on one of these labels. Note that Industry Canada

regulations provide that changes or modifications not expressly approved by

Dell could void your authority to operate this equipment.

This Class B (or Class A, if so indicated on the registration label) digital

apparatus meets the requirements of the Canadian Interference-

Causing Equipment Regulations.

Cet appareil numérique de la Classe B (ou Classe A, si ainsi indiqué sur

l’étiquette d’enregistration) respecte toutes les exigences du Reglement

sur le Materiel Brouilleur du Canada.

18 Dell PowerConnect RPS-600 Setup Guide

www.dell.com | support.dell.com

CE Notice (European Union)

Marking by the symbol indicates compliance of this Dell computer to

the EMC Directive and the Low Voltage Directive of the European Union.

Such marking is indicative that this Dell system meets the following

technical standards:

• EN 55022 — "Information Technology Equipment — Radio

Disturbance Characteristics — Limits and Methods of Measurement."

• EN 55024 — "Information Technology Equipment - Immunity

Characteristics - Limits and Methods of Measurement."

• EN 61000-3-2 — "Electromagnetic Compatibility (EMC) - Part 3:

Limits - Section 2: Limits for Harmonic Current Emissions

(Equipment Input Current Up to and Including 16 A Per Phase)."

• EN 61000-3-3 — "Electromagnetic Compatibility (EMC) - Part 3:

Limits - Section 3: Limitation of Voltage Fluctuations and Flicker in

Low-Voltage Supply Systems for Equipment With Rated Current Up

to and Including 16 A."

• EN 60950 — "Safety of Information Technology Equipment."

NOTE: EN 55022 emissions requirements provide for two classifications:

• Class A is for typical commercial areas.

• Class B is for typical domestic areas.

RF INTERFERENCE WARNING: This is a Class A product. In a

domestic environment this product may cause radio frequency (RF)

interference, in which case the user may be required to take adequate

measures.

A "Declaration of Conformity" in accordance with the preceding directives

and standards has been made and is on file at Dell Computer Corporation

Products Europe BV, Limerick, Ireland.

Dell PowerConnect RPS-600 Setup Guide 19

Simplified Chinese Class A Warning Notice (China Only)

On Class A systems, the following warning will appear near the regulatory

label:

Warning: This is a Class A product. In a domestic environment this

product may cause radio interference, in which case the user may be

required to take adequate measures.

EN 55022 Compliance (Czech Republic Only)

VCCI Notice (Japan Only)

Most Dell computer systems are classified by the Voluntary Control Council

for Interference (VCCI) as Class B information technology equipment

(ITE). However, the inclusion of certain options can change the rating of

some configurations to Class A. ITE, including peripherals, expansion cards,

printers, input/output (I/O) devices, monitors, and so on, integrated into or

connected to the system should match the electromagnetic environment

classification (Class A or B) of the computer system.

This device belongs to Class B devices as described in EN 55022, unless

it is specifically stated that it is a Class A device on the specification

label. The following applies to devices in Class A of EN 55022 (radius of

protection up to 30 meters). The user of the device is obliged to take all

steps necessary to remove sources of interference to telecommunication

or other devices.

Pokud není na typovém štítku počítače uvedeno, že spadá do

třídy A podle EN 55022, spadá automaticky do třídy B podle

EN 55022. Pro zařízení zařazená do třídy A (ochranné pásmo

30 m) podle EN 55022 platí následující. Dojde−li k rušení

telekomunikačních nebo jinych zařízení, je uživatel povinen

provést taková opatření, aby rušení odstranil.

Strona jest ładowana ...

Dell Power Supply 2T227 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Dell Power Supply 2T227 Instrukcja obsługi

w innych językach

Powiązane dokumenty