Parkside PASSK 20-Li A1 Instrukcja obsługi

Kategoria
Elektronarzędzia
Typ
Instrukcja obsługi
CORDLESS VEHICLE IMPACT WRENCH 20V / AKKU-
KFZ-DREHSCHLAGSCHRAUBER 20 V / VISSEUSE À
CHOCS SANS FIL POUR VOITURE 20 V PASSK 20-Li A1
AKKU-KFZ-
DREHSCHLAGSCHRAUBER 20 V
Originalbetriebsanleitung
AKU RÁZOVÝ UTAHOVÁK
NA KOLA AUTA 20 V
Překlad originálního provozního návodu
AKU RÁZOVÝ UŤAHOVÁK
NA KOLESÁ AUTA 20 V
Preklad originálneho návodu na obsluhu
VISSEUSE À CHOCS SANS
FIL POUR VOITURE 20 V
Traduction des instructions d’origine
ACCU-VOERTUIG-DRAAISLAG-
SCHROEFMACHINE 20 V
Vertaling van de originele gebruiksaanwijzing
WIERTARKO-WKRĘTARKA SAMOCHO-
DOWA, AKUMULATOROWA 20 V
Tłumaczenie oryginalnej instrukcji obsługi
CORDLESS VEHICLE
IMPACT WRENCH 20V
Translation of the original instructions
IAN 368334_2010
BATTERIDREVEN SLAGNØGLE
TIL MOTORKØRETØJ 20 V
Oversættelse af den originale driftsvejledning
ATORNILLADORA DE IMPACTO
RECARGABLE PARA COCHE 20 V
Traducción del manual de instrucciones original
GB Translation of the original instructions Page 1
DE Originalbetriebsanleitung Seite 13
FR Traduction des instructions d’origine Page 25
NL Vertaling van de originele gebruiksaanwijzing Pagina 39
CZ Překlad originálního provozního návodu Strana 51
PL Tłumaczenie oryginalnej instrukcji obsługi Strona 63
SK Preklad originálneho návodu na obsluhu Strana 77
ES Traducción del manual de instrucciones original Página 89
DK Oversættelse af den originale driftsvejledning Side 103
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l‘appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas
las funciones del dispositivo.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
A
All Parkside tools and the chargers PLG20A1/PLG 20 A4/PLG 20 C1/PLG20A2/PLG20A3/
PLG 20 C3/PDSLG 20 A1 of the X20V Team series are compatible with the PAP20 A1/
PAP20A2 / PAP 20 A3 /PAP 20 B1/PAP 20 B3 battery pack.
Alle Parkside Geräte und die Lade geräte PLG 20 A1/PLG 20 A4/PLG 20 C1/PLG 20 A2/
PLG20A3/PLG 20 C3/PDSLG 20 A1 der X20V Team Serie sind mit dem Akku-Pack
PAP 20 A1/PAP 20 A2/PAP20 A3/PAP 20 B1/PAP 20 B3 kompatibel.
Tous les outils Parkside et les chargeurs PLG 20 A1/PLG 20 A4/PLG 20 C1/PLG20A2/
PLG 20 A3/PLG 20 C3/PDSLG 20 A1 de la série X20V Team sont compatibles avec la batterie
PAP 20 A1/PAP 20 A2/PAP 20 A3/PAP 20 B1/PAP 20 B3.
Charging times
Ladezeiten
Temps de charge
Charging currents
Ladeströme
Courants de charge
2 Ah
Battery pack
Akku
Batterie
PAP 20 A1/B1
3 Ah
Battery pack
Akku
Batterie
PAP 20 A2
4 Ah
Battery pack
Akku
Batterie
PAP 20 A3/B3
max. 2,4 A
Charger PLG 20 A1/A4/C1
Ladegerät
Chargeur
60 min
2,4 A
90 min
2,4 A
120 min
2,4 A
max. 3,5 A
Charger PLG 20 A2
Ladegerät
Chargeur
45 min
3,5 A
60 min
3,5 A
80 min
3,5 A
max. 4,5 A
Charger PLG 20 A3/C3
Ladegerät
Chargeur
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
max. 4,5 A
Ladegerät PDSLG 20 A1
Charger
Chargeur
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
PASSK 20-Li A1 GBIE 1
Contents
Introduction ............................................................2
Intended use ........................................................................2
Features ...........................................................................2
Package contents ....................................................................2
Technical data ......................................................................2
General power tool safety warnings .......................................3
1. Work area safety ..................................................................4
2. Electrical safety ...................................................................4
3. Personal safety ....................................................................4
4. Power tool use and care ............................................................5
5. Battery tool use and care ............................................................5
6. Service ..........................................................................6
Safety instructions specifically for impact screwdrivers .......................................6
Safety guidelines for battery chargers ....................................................6
Original accessories/auxiliary equipment .................................................6
Before use ............................................................. 7
Charging the battery pack (see fig. A) ....................................................7
Attaching/disconnecting the battery pack to/from the appliance ...............................7
Checking the battery charge level .......................................................7
Use ................................................................... 7
Switching on and off .................................................................7
Setting/preselecting the rotation speed/tightening torque .....................................7
Changing the direction of rotation .......................................................8
Fitting the socket .....................................................................8
Maintenance and cleaning ................................................8
Disposal ............................................................... 8
Kompernass Handels GmbH warranty .....................................9
Service ............................................................... 10
Importer .............................................................10
Translation of the original Conformity Declaration ...........................11
Ordering a replacement battery .......................................... 12
Telephone ordering .................................................................12
PASSK 20-Li A1
2 GBIE
CORDLESS VEHICLE IMPACT
WRENCH 20V PASSK 20-Li A1
Introduction
Congratulations on the purchase of your new appli-
ance. You have chosen a high-quality product. The
operating instructions are part of this product. They
contain important information about safety, usage
and disposal. Before using the product, please
familiarise yourself with all operating and safety
instructions. Use the product only as described and
for the range of applications specified. Please also
pass these operating instructions on to any future
owner.
Intended use
This appliance is intended for screwing in and
unscrewing screws as well as for tightening and
loosening nuts. The appliance has a clockwise/
anticlockwise rotation, a 1/2" external square
drive bit holder and an LED working light. The light
on this appliance is intended to illuminate the im-
mediate working area of the appliance. The rotary
impact function of the appliance enables the power
of the motor to be converted into uniform rotary
impacts. The impact mechanism comes into effect
during tightening and loosening.
The appliance is designed for use by adults. Young
people under 16 years of age may only use the
appliance under supervision. The manufacturer ac-
cepts no liability for damages caused by improper
use or incorrect operation of the appliance.
Use this product only as described and for the
areas of applications specified. The appliance is
not intended for commercial use. Any other usage
or modification of the appliance is deemed to be
improper and carries a significant risk of accidents.
The manufacturer accepts no responsibility for
damage(s) attributable to misuse.
Features
Tool holder
Rotation direction switch/lock
Belt clip
Battery charge level button
Battery display LED
Battery pack*
Release button for the battery pack
LED work light
Torque preselection button
ON/OFF switch / speed control
Sockets (17/19/21/23 mm)
High-speed charger*
Red charge control LED
Green charge control LED
Package contents
1 cordless vehicle impact wrench 20V
PASSK 20-Li A1
4 sockets (17/19/21/23 mm)
1 belt clip
1 carrying case
1 set of operating instructions
Technical data
Cordless vehicle impact wrench 20V
PASSK 20-Li A1
Rated voltage 20 V (DC)
Idle speed 0–2300 rpm
Rated stroke rate 0–3000 rpm
Max. torque 400 Nm
Torque selectable at 5 levels 100/150/200/
300/400 Nm
Tool holder 1/2"
PASSK 20-Li A1 GBIE 3
Rechargeable battery PAP 20 B3*
Type LITHIUM ION
Rated voltage 20 V (DC)
Capacity 4 Ah/80Wh
Cells 10
NOTE
Note that the full performance of the unit
can only be achieved if the PAP 20 A3/
PAP20B3 battery is used.
High-speed battery charger PLG 20 C3*
INPUT
Rated voltage 230–240 V ∼,
50 Hz (AC)
Rated power
consumption 120 W
Fuse (internal) 3.15 A
T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 4.5 A
Charging time approx. 60 min
Protection class II / (double insulation)
* BATTERY AND CHARGER ARE NOT INCLUDED
Noise emission value
Noise measurement value determined in
accordance with EN 62841. The A-rated noise
level of the power tool is typically:
Sound pressure level LPA = 93.6 dB (A)
Uncertainty K KPA = 3 dB
Sound power level LWA = 104.6 dB (A)
Uncertainty K KWA = 3 dB
Vibration emission value
Total vibration values (vector total of three direc-
tions) determined in accordance with EN 62841:
Tightening screws and nuts of maximum permissible
size ah = 9.425 m/s2
Uncertainty K = 1.5 m/s2
Wear hearing protection!
NOTE
The vibration emission values and the noise
emission values given in these instructions
have been measured in accordance with
a standardised test procedure and can be
used for comparison of the power tool with
another tool.
The specified total vibration values and the
noise emission values can also be used to
make a provisional load estimate.
WARNING!
Depending on the manner in which the
power tool is being used, and in particular
the kind of workpiece that is being worked,
the vibration and noise emission values can
deviate from the values given in these instruc-
tions during actual use of the power tool.
Try to keep the load as low as possible.
Measures to reduce the vibration load are,
e.g. wearing gloves and limiting the working
time. Wherein all states of operation must be
included (e.g. times when the power tool is
switched off and times where the power tool
is switched on but running without load).
General power tool
safety warnings
WARNING!
Read all safety warnings, instructions,
illustrations and specifications provided
with this power tool. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
PASSK 20-Li A1
4 GBIE
The term „power tool“ in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flam-
mable liquids, gases or dust. Power tools cre-
ate sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entan-
gled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment
such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising
power tools that have the switch on invites ac-
cidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent
and ignore tool safety principles. A careless
action can cause severe injury within a fraction
of a second.
PASSK 20-Li A1 GBIE 5
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detach-
able, from the power tool before making any
adjustments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool ac-
cidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired be-
fore use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in unex-
pected situations.
5. Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek medi-
cal help. Liquid ejected from the battery may
cause irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire
or temperature above 130 °C (265°F) may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside the specified range may damage the
battery and increase the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries!
Protect the recharge-
able battery from heat, for example from
continuous exposure to sunlight, fire, water
and moisture. There is a risk of explosion.
PASSK 20-Li A1
6 GBIE
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized
service providers.
Safety instructions specifically for
impact screwdrivers
Wear hearing protection when impact
screwing. Exposure to loud noise can lead
to hearing loss.
Secure the workpiece! A workpiece securely
held by a clamping device or vice is much safer
than one held in your hand.
Hold the power tool firmly. High torques can
occur for brief periods while tightening and
loosening screws.
Wait until the power tool has come to a stand-
still before putting it down. The tool can jam,
this leading to loss of control of the power tool.
Hold the power tool by the insulated gripping
surfaces, when performing an operation where
the screw could come into contact with hidden
wiring. Contact between the screw or attached
tool and a live wire may cause exposed metal
parts of the power tool to become live and give
the operator an electric shock.
Safety guidelines for battery
chargers
This appliance may be used by
children aged 8 years and above
and by persons with limited physical,
sensory or mental capabilities or
lack of experience and knowledge,
provided that they are under super-
vision or have been told how to use
the appliance safely and are aware
of the potential risks. Do not allow
children to use the appliance as a
toy. Cleaning and user maintenance
tasks must not be carried out by
children unless they are supervised.
The charger is suitable
for indoor use only.
ATTENTION!
This charger can only charge the follow-
ing batteries:
PAP 20 A1/PAP 20 A2/
PAP20A3/PAP 20 B1/PAP 20 B3.
A current list of battery compatibility can be
found at www.lidl.de/Akku.
WARNING!
To avoid potential risks, damaged mains
cables should be replaced by the manufac-
turer, their customer service department or a
similarly qualified person.
Original accessories/auxiliary
equipment
Use only accessories and auxiliary equipment
specified in the operating instructions and which
are compatible with the appliance.
WARNING!
Do not use any accessories which are not
recommended by PARKSIDE. This can lead to
an electric shock and fire.
PASSK 20-Li A1 GBIE 7
ATTENTION! Hot surface.
There is a risk of burns.
Before use
Charging the battery pack (see fig. A)
CAUTION!
Always pull out the power plug before you
remove the battery pack from or connect the
battery pack to the charger.
NOTE
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level
is between 50% and 80%. The storage cli-
mate should be cool and dry and the ambi-
ent temperature should be between 0°C and
50°C.
Connect the battery pack to the high-speed
battery charger (see Fig. A).
Insert the power plug into the socket. The control
LED lights up red.
The green LED indicates that the charging
process is complete and the battery pack
is ready for use.
CAUTION!
If the red control LED flashes, this means
that the battery pack has overheated and
cannot be charged.
If the red and green control LEDs both
flash, this means that the battery pack is
defective.
Push the battery pack back into the appliance.
Switch off the charger for at least 15 minutes
between successive charging sessions. Also dis-
connect the power plug from the mains power
socket.
Attaching/disconnecting the battery
pack to/from the appliance
Attaching the battery pack
Push the rotation direction switch into the
middle position (lock). Push the battery pack
into the handle until it clicks into place.
Removing the battery pack
Press the release button and remove the
battery pack .
Checking the battery charge level
Press the battery charge level button to
check the status of the battery (see also main
diagram).
The status/remaining charge will be shown on
the battery display LED as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Use
Switching on and off
Switching on
To start the appliance, press the ON/OFF
switch and keep it pressed in.
The LED working light lights up when the
ON/OFF switch is depressed lightly or fully.
This provides illumination of the work area in
poor lighting conditions.
Switching off
Release the ON/OFF switch to switch off the
appliance.
Setting/preselecting the rotation
speed/tightening torque
Press the torque preselection button to select
the required torque in stages.
Press the ON/OFF switch lightly for a low
speed/tightening torque. Increasing the pres-
sure increases the speed/tightening torque.
The tightening torque depends on the selected
speed/torque preselection and impact duration.
PASSK 20-Li A1
8 GBIE
NOTE
However, to tighten lug nuts, the smallest
torque setting must be selected to avoid over
tightening.
The integrated motor brake ensures rapid
stoppage.
CAUTION!
The tightening torque actually attained must
always be checked with a torque wrench!
Changing the direction of rotation
Change the direction of rotation by pressing
the rotation direction switch towards the left
or right.
Fitting the socket
Push one of the supplied sockets onto the
tool holder .
Maintenance and cleaning
WARNING! RISK OF INJURY! Always
switch off the appliance and remove
the battery before carrying out any
work on the appliance.
The appliance is maintenance-free.
The appliance must always be kept clean, dry
and free from oil or grease.
Never allow liquids to get into the appliance.
Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which
can damage plastic.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
NOTE
Replacement parts not listed (such as carbon
brushes, switch) can be ordered via our
service hotline.
Disposal
The packaging is made from environ-
mentally friendly material and can be
disposed of at your local recycling
plant.
Do not dispose of power tools in
your normal domestic waste!
European Directive 2012/19/EU
requires that worn-out power tools be
collected separately and recycled in an environ-
mentally compatible manner.
Do not dispose of batteries in
your normal household waste!
Remove the batteries from the appli-
ance before disposal. Defective or
worn-out rechargeable batteries must be recycled
according to Directive 2006/66/EC. Take the
battery pack and/or appliance to a nearby collec-
tion facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Dispose of the packaging in an
environmentally friendly manner.
Note the labelling on the packaging
and separate the packaging material
components for disposal if necessary. The packag-
ing material is labelled with abbreviations (a) and
numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites.
Your local community or municipal
authorities can provide information
on how to dispose of the worn-out
product.
The product is recyclable, subject to
extended producer responsibility and
is collected separately.
PASSK 20-Li A1 GBIE 9
Kompernass Handels GmbH
warranty
Dear Customer,
This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults,
you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the
warranty described below.
Warranty conditions
The warranty period starts on the date of purchase.
Please keep your receipt in a safe place. This will
be required as proof of purchase.
If any material or manufacturing fault occurs within
three years of the date of purchase of the product,
we will either repair or replace the product for you
or refund the purchase price (at our discretion).
This warranty service requires that you present the
defective appliance and the proof of purchase (re-
ceipt) within the three-year warranty period, along
with a brief written description of the fault and of
when it occurred.
If the defect is covered by the warranty, your prod-
uct will either be repaired or replaced by us. The
repair or replacement of a product does not signify
the beginning of a new warranty period.
X 12 V and X 20 V Team Series battery packs
come with a 3-year warranty valid from the date of
purchase.
Warranty period and statutory claims for
defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must
be reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or to fragile
parts which could be considered as consumable
parts such as switches or parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improp-
erly maintained. The directions in the operating
instructions for the product regarding proper use
of the product are to be strictly followed. Uses
and actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall
be deemed void in cases of misuse or improper
handling, use of force and modifications / repairs
which have not been carried out by one of our
authorised Service centres.
PASSK 20-Li A1
10 GBIE
The warranty period does not apply to
Normal reduction of the battery capacity
overtime
Commercial use of the product
Damage to or alteration of the product by the
customer
Non-compliance with safety and maintenance
instructions, operating errors
Damage caused by natural hazards
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
Please have the till receipt and the item number
(e.g.IAN12345) available as proof of purchase.
You will find the item number on the type plate
on the product, an engraving on the product,
on the front page of the operating instructions
(below left) or on the sticker on the rear or bot-
tom of the product.
If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
You can return a defective product to us free of
charge to the service address that will be pro-
vided to you. Ensure that you enclose the proof
of purchase (till receipt) and information about
what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and installation
software at www.lidl-service.com.
This QR code will take you directly to the Lidl
service page (www.lidl-service.com) where you
can open your operating instructions by entering
the item number (IAN) 368334_2010.
WARNING!
Have the power tool repaired by the service
centre or a qualified electrician and only
using genuine replacement parts. This will
ensure that the safety of the appliance is
maintained.
Always ensure that the power plug or the
mains cable is replaced only by the manu-
facturer of the appliance or its customer
service. This will ensure that the safety of the
appliance is maintained.
Service
Service Great Britain
Tel.: 0800 404 7657
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
IAN 368334_2010
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
PASSK 20-Li A1 GBIE 11
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, document officer: Mr Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards,
normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EC Low Voltage Directive (charger only)
(2014/35/EU)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
* The manufacturer bears full responsibility for compliance with this conformity declaration. The object of the
declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament
and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic
appliances.
Applied harmonised standards
EN 62841-1:2015
EN 62841-2-2:2014
EN 60335-1:2012/A2:2019
EN 60335-2-29:2004/A11:2018
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015
EN IEC 61000-3-2:2019
EN 61000-3-3:2013/A1:2019
EN 50581:20122
Type/appliance designation: Cordless vehicle impact wrench 20V PASSK 20-Li A1
Year of manufacture: 01–2021
Serial number: IAN 368334_2010
Bochum, 18/01/2021
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the context of further product development.
PASSK 20-Li A1
12 GBIE
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the
Internet on www.kompernass.com or by telephone.
Due to limited stocks, this item may sell out in a relatively short time.
NOTE
Online ordering of replacement parts is not possible in all countries. In this case, please contact the
Service hotline.
Telephone ordering
Service Great Britain Tel.: 0800 404 7657
Service Ireland Tel.: 1890 930 034
(0,08 EUR/Min., peak · 0,06 EUR/Min., off peak)
To ensure that your order is processed swiftly, have the article number of your appliance to hand
(e.g.IAN368334) in case of questions. The article number can be found on the type plate or the
titlepage of these instructions.
PASSK 20-Li A1 DEATCH 13
Inhaltsverzeichnis
Einleitung ............................................................. 14
Bestimmungsgemäßer Gebrauch .......................................................14
Ausstattung ........................................................................14
Lieferumfang .......................................................................14
Technische Daten ...................................................................14
Allgemeine Sicherheitshinweise für Elektrowerkzeuge .......................15
1. Arbeitsplatzsicherheit ..............................................................16
2. Elektrische Sicherheit ..............................................................16
3. Sicherheit von Personen ............................................................16
4. Verwendung und Behandlung desElektrowerkzeugs .....................................17
5. Verwendung und Behandlung desAkkuwerkzeugs .......................................17
6. Service .........................................................................18
Gerätespezifische Sicherheits hinweise für Schlagschrauber ..................................18
Sicherheitshinweise für Ladegeräte .....................................................19
Originalzubehör/-zusatzgeräte ........................................................19
Vor der Inbetriebnahme ................................................19
Akku-Pack laden (siehe Abb. A) ........................................................19
Akku-Pack ins Gerät einsetzen/entnehmen ...............................................20
Akkuzustand prüfen .................................................................20
Inbetriebnahme .......................................................20
Ein-/ausschalten ....................................................................20
Drehzahl/Anziehdrehmoment einstellen/vorwählen ........................................20
Drehrichtung umschalten .............................................................20
Stecknuss aufsetzen .................................................................20
Wartung und Reinigung .................................................20
Entsorgung ...........................................................21
Garantie der Kompernaß Handels GmbH ..................................21
Service ............................................................... 22
Importeur ............................................................22
Original-Konformitätserklärung ..........................................23
Ersatz-Akku Bestellung .................................................24
Telefonische Bestellung ...............................................................24
PASSK 20-Li A1
14 DEATCH
AKKU-KFZ-DREH-
SCHLAGSCHRAUBER 20 V
PASSK 20-Li A1
Einleitung
Wir beglückwünschen Sie zum Kauf Ihres neuen
Gerätes. Sie haben sich damit für ein hochwertiges
Produkt entschieden. Die Bedienungsanleitung ist
Teil dieses Produkts. Sie enthält wichtige Hinweise
für Sicherheit, Gebrauch und Entsorgung. Machen
Sie sich vor der Benutzung des Produkts mit allen
Bedien- und Sicherheitshinweisen vertraut. Benut-
zen Sie das Produkt nur wie beschrieben und für
die angegebenen Einsatzbereiche. Händigen Sie
alle Unterlagen bei Weitergabe des Produkts an
Dritte mit aus.
Bestimmungsgemäßer Gebrauch
Das Gerät ist zum Eindrehen und Lösen von
Schrauben sowie zum Anziehen und Lösen von
Muttern vorgesehen. Das Gerät besitzt einen
Rechts-/Linkslauf, eine 1/2“ Außenvierkant Werk-
zeugaufnahme und ein LED-Arbeitslicht. Das Licht
dieses Gerätes ist dazu bestimmt, den direkten
Arbeitsbereich des Gerätes zu beleuchten. Mit der
Drehschlagfunktion des Gerätes wird die Kraft des
Motors in gleichmäßige Drehschläge umgesetzt.
Das Schlagwerk setzt beim Festziehen und beim
Lösen ein.
Das Gerät ist zum Gebrauch durch Erwachsene
bestimmt. Jugendliche über 16 Jahre dürfen das
Gerät nur unter Aufsicht benutzen. Der Hersteller
haftet nicht für Schäden, die durch bestimmungs-
widrigen Gebrauch oder falsche Bedienung ver-
ursacht wurden.
Benutzen Sie das Gerät nur wie beschrieben und
für die angegebenen Einsatzbereiche. Das Gerät
ist nicht für den gewerblichen Einsatz bestimmt.
Jede andere Verwendung oder Veränderung des
Gerätes gilt als nicht bestimmungsgemäß und birgt
erhebliche Unfallgefahren. Für aus bestimmungs-
widriger Verwendung entstandene Schäden über-
nimmt der Hersteller keine Haftung.
Ausstattung
Werkzeugaufnahme
Drehrichtungsumschalter/Sperre
Gürtelclip
Taste Akkuzustand
Akku-Display-LED
Akku-Pack*
Taste zur Entriegelung des Akku-Packs
LED-Arbeitsleuchte
Taste für die Drehmomentvorwahl
EIN-/AUS-Schalter/Drehzahlregulierung
Stecknüsse (17/19/21/23 mm)
Schnell-Ladegerät*
Rote Ladekontroll-LED
Grüne Ladekontroll-LED
Lieferumfang
1 Akku-KFZ-Drehschlagschrauber 20 V
PASSK 20-Li A1
4 Stecknüsse 17/19/21/23 mm
1 Gürtelclip
1 Tragekoffer
1 Bedienungsanleitung
Technische Daten
Akku-KFZ-Drehschlagschrauber 20 V
PASSK 20-Li A1
Bemessungsspannung 20 V (Gleichstrom)
Leerlaufdrehzahl 0–2300 min-1
Nennschlagzahl 0–3000 min-1
Max. Drehmoment 400 Nm
Drehmoment in
5 Stufen vorwählbar 100/150/200/
300/400Nm
Werkzeugaufnahme 1/2“
PASSK 20-Li A1 DEATCH 15
Akku PAP 20 B3*
Typ LITHIUM-IONEN
Bemessungsspannung 20 V (Gleichstrom)
Kapazität 4 Ah/80Wh
Zellen 10
HINWEIS
Beachten Sie, dass die volle Leistung des
Gerätes nur bei Verwendung des Akkus
PAP 20 A3/PAP 20 B3 erreicht werden kann.
Akku-Schnellladegerät PLG 20 C3*
EINGANG/Input
Bemessungsspannung 230–240 V ∼, 50 Hz
(Wechselstrom)
Bemessungsaufnahme 120 W
Sicherung (innen) 3,15 A
T3.15A
AUSGANG/Output
Bemessungsspannung 21,5 V (Gleichstrom)
Bemessungsstrom 4,5 A
Ladedauer ca. 60 min
Schutzklasse II / (Doppelisolierung)
* AKKU UND LADEGERÄT SIND NICHT IM LIEFER-
UMFANG ENTHALTEN
Geräuschemissionswert
Messwert für Geräusch ermittelt entsprechend
EN62841. Der A-bewertete Geräuschpegel des
Elektrowerkzeugs beträgt typischerweise:
Schalldruckpegel LPA = 93,6 dB (A)
Unsicherheit K KPA = 3 dB
Schallleistungspegel LWA = 104,6 dB (A)
Unsicherheit K KWA = 3 dB
Schwingungsemissionswert
Schwingungsgesamtwerte (Vektorsumme dreier
Richtungen) ermittelt entsprechend EN 62841:
Anziehen von Schrauben und Muttern maximaler
zulässiger Größe ah = 9,425 m/s2
Unsicherheit K = 1,5 m/s2
Gehörschutz tragen!
HINWEIS
Die angegebenen Schwingungsgesamtwerte
und die angegebenen Geräuschemissions-
werte sind nach einem genormten Prüfver-
fahren gemessen worden und können zum
Vergleich eines Elektrowerkzeugs mit einem
anderen verwendet werden.
Die angegebenen Schwingungsgesamtwerte
und die angegebenen Geräuschemissions-
werte können auch zu einer vorläufigen Ein-
schätzung der Belastung verwendet werden.
WARNUNG!
Die Schwingungs- und Geräuschemissionen
können während der tatsächlichen Benutzung
des Elektrowerkzeugs von den Angabewerten
abweichen, abhängig von der Art und Weise,
in der das Elektrowerkzeug verwendet wird,
insbesondere, welche Art von Werkstück be-
arbeitet wird.
Versuchen Sie, die Belastung so gering wie
möglich zu halten. Beispielhafte Maßnahmen
zur Verringerung der Vibrationsbelastung sind
das Tragen von Handschuhen beim Gebrauch
des Werkzeugs und die Begrenzung der Ar-
beitszeit. Dabei sind alle Anteile des Betriebs-
zyklus zu berücksichtigen (beispielsweise
Zeiten, in denen das Elektrowerkzeug ab-
geschaltet ist, und solche, in denen es zwar
eingeschaltet ist, aber ohne Belastung läuft).
Allgemeine
Sicherheitshinweise für
Elektrowerkzeuge
WARNUNG!
Lesen Sie alle Sicherheitshinweise, Anwei-
sungen, Bebilderungen und technischen
Daten, mit denen dieses Elektrowerkzeug
versehen ist. Versäumnisse bei der Einhaltung
der nachfolgenden Anweisungen können
elektrischen Schlag, Brand und/oder schwere
Verletzungen verursachen.
Bewahren Sie alle Sicherheitshinweise und
Anweisungen für die Zukunft auf.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120

Parkside PASSK 20-Li A1 Instrukcja obsługi

Kategoria
Elektronarzędzia
Typ
Instrukcja obsługi