Whirlpool ADG 6966/1 IXM WP instrukcja
- Kategoria
- Zmywarki
- Typ
- instrukcja
Niniejsza instrukcja jest również odpowiednia dla
10
INSTRUCTIONS FOR USE
BEFORE USING THE DISHWASHER/CONNECTIONS
ELECTRICAL CONNECTION
PRECAUTIONS AND GENERAL RECOMMENDATIONS
HOW TO FILL THE SALT CONTAINER
HOW TO FILL THE RINSE AID DISPENSER
HOW TO FILL THE DETERGENT DISPENSER
CARE AND MAINTENANCE
11
BEFORE USING THE DISHWASHER/CONNECTIONS
1. Removing the packaging and controls:
After unpacking, make sure that the dishwasher is
undamaged and that the door closes correctly. If
in doubt, contact a qualified technician or your
local retailer.
•
Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children, as
they are potentially dangerous.
2. Water and electrical connections:
All water and electrical connections must be
carried out by a qualified technician in
compliance with the manufacturer's instructions
(refer to the enclosed installation booklet) and
current local safety regulations.
The appliance must only be used in the household
for the prescribed uses.
Do not use the dishwasher if it has been damaged
in transit. Consult your local retailer or our
After-Sales Service.
(Refer to the separate installation instructions
booklet)
3. Water inlet and drain:
•
Observe any special regulations issued by your
local Water Board.
Water supply pressure: 0.3 - 10 bar.
•
Make sure the inlet and drain hoses are kink-free
and are not crushed.
•
If the hose length is not sufficient, please contact
your local dealer or our After-Sales Service.
•
The inlet hose must be securely clamped to the
water tap to prevent leaks.
•
The inlet water temperature varies according to the
model installed. Inlet hose marked “25°C Max”:
maximum temperature 25°C.
All other models: maximum temperature 60° C.
•
When installing the appliance, make sure the drain
water discharges correctly (if necessary, remove
the wire gauze from the sink siphon).
•
Fix the drain hose to the spigot with a clamp to
prevent it from coming off during operation.
For appliances with water-stop system only: If the
water connections are made correctly, the water-
stop system safeguards your home against damage
caused by flooding.
4. Electrical connection:
•
Closely adhere to local Electricity Board
regulations.
•
Voltage information is shown on the rating plate
mounted inside the door on the right hand side.
•
The appliance must be earthed as prescribed by law.
•
Do not use extension leads or multiple adapters.
•
Before carrying out maintenance, disconnect the
mains plug.
•
The power cable must only be replaced by
authorized personnel.
Warning for models provided with LCD display:
The mains plug must be positioned in an easily
accessible place.
• For Austria:
if the apparatus is series connected to
a fault current switch, this must be sensitive to the
pulsating current.
12
ELECTRICAL CONNECTION
1) For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A 13amp
fused plug, to change a fuse in this type of plug use an A.S.T.A.
approved fuse to BS 1362 type and proceed as follows:
1.
Remove the fuse cover (
A
) and fuse (
B
).
2.
Fit replacement 13A fuse into fuse cover.
3.
Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the fuse
cover is lost the plug must not be used until a correct replacement
is fitted.
Correct replacement are identified by the colour insert or the colour
embossed in words on the base of the plug.
Replacement fuse covers are available from your local electrical
store.
2) For the Republic of Ireland only
The information given in respect of Great Britain will frequently
apply, but a third type of plug and socket is also used, the
2-pin, side earth type.
3) Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please
contact Whirlpool Service for further instruction. Please do not
attempt to change plug yourself. This procedure needs to be carried
out by a qualified Whirlpool technician in compliance with the
manufactures instructions and current standard safety regulations.
13
PRECAUTIONS AND GENERAL RECOMMENDATIONS
1. Packing:
The packing box may be fully recycled as
confirmed by the recycling symbol.
2. Energy and water saving tips:
•
Do not rinse crockery under running water.
•
Always fully load the dishwasher before switching
on or set the wash programme to Half load/
Multizone (if available) if
one
rack only is loaded.
•
If ecological energy sources are available such as
solar panel heating, heat pumps or centralised
heating systems, the appliance may be connected
to the hot water mains up to a maximum
temperature of 60° C. Make sure the water inlet
hose is of the correct type. Refer to the
“Connections” chapter in these user instructions.
3. Disposal:
The appliance is built from reusable materials.
If you decide to scrap the dishwasher, it must be
disposed of in compliance with local waste
disposal laws.
Before scrapping, cut off the power cable so that
the appliance cannot be connected to the mains.
4. Child safety:
•
Children must not be allowed to play with the
dishwasher.
•
Store the detergent, rinse aid and salt in a dry
place out of the reach of children.
5. General recommendations:
•
The open dishwasher door can only support the
weight of the loaded rack when pulled out. Do not
rest objects on the open door or sit or stand on it:
the appliance may topple over!
•
Do not use solvents inside the dishwasher:
risk of
explosion!
•
Only use detergents, rinse aids and regeneration
salts specially recommended for use in domestic
dishwashers.
•
Before cleaning or carrying out maintenance,
switch off the appliance, disconnect the mains
plug and turn off the water tap.
•
If a fault occurs, switch off the appliance and turn
off the water tap.
•
If necessary, the power cable may be replaced with
one the same obtained from our After-Sales
Service. The power cable must only be replaced by
a qualified technician.
•
On completion of the programme switch off the
dishwasher and turn off the water tap.
6. For appliances with water stop system:
The water inlet hose and plastic casing contain
electrical components. Do not therefore cut the
hose or immerse the plastic casing in water.
If the hose is damaged switch off the appliance
immediately.
EC Declaration of conformity:
This appliance has been designed, constructed
and distributed in compliance with the safety
requirements of EC Directives:
•
73/23/EC
•
89/336/EC
•
93/68/EC
Load capacity:
12 place settings.
14
HOW TO FILL THE SALT CONTAINER
From a water hardness category of 1–2 (medium), before using the
dishwasher for the first time, fill the salt container with regeneration
salt (to find out the hardness level of water in your area, contact your
local Water Board or check the last bill you received).
If the water hardness level does not correspond to position 3 on the
selector (factory setting) or if the water hardness level changes:
Turn the selector to the correct position (for dishwashers without
salt sensor only):
Set the water hardness by turning the selector (if fitted) inside the door
(top left) using a screwdriver.
Use the table below to set the dial to the correct setting:
Hardness
level
German
degrees
°dH
French
degrees
°fH
mmol/l Clarke scale
or English
degrees
°eH
Setting
For dishwashers without salt sensor
only! In appliances provided with a salt
sensor, the selector automatically turns
to the correct position.
1 soft 0 - 5 0 - 9 0 - 0,9 0 - 6,3 0
1 - 2 medium 6 - 10 10 - 18 1,0 - 1,8 7 - 12,6 1
2 average 11 - 15 19 - 27 1,9 - 2,7 13,3 - 18,9 2
3 medium-
hard
16 - 21 28 - 37 2,8 - 3,7 19,6 - 25,9 3
4 hard 22 - 28 38 - 50 3,8 - 5,0 26,6 - 35 4
4 very hard 29 - 35 51 - 63 5,1 - 6,3 35,7 - 44,1 5
4 extremely
hard
36 - 60 64 - 107 6,4 - 10,7 44,8 - 74,9 6
If the water hardness level falls within
category 1 (soft), no salt is required.
How to fill the salt container
Warning: Only use regeneration salts for use in domestic dishwashers!
Do not fill the salt container with unsuitable substances, such as.
detergent, as this will cause irreparable damage to the water softener
system.
1.
Remove the lower rack.
2.
Unscrew the cap by turning it counter-clockwise.
3.
When first using the dishwasher: fill the salt container to the rim
with water.
4.
Fill the salt container to the rim with salt (using the filler
provided) (when filling for the first time use min. 1.5 kg and
max. 2 kg) and stir with a spoon handle.
5.
Screw the cap back on by turning it clockwise.
6.
Fit the lower rack.
7.
If regeneration salt is to be added,
immediately
start a wash
programme (rinsing alone is not sufficient) in order to eliminate
any residual saline solution straight away and avoid corrosion.
Salt level indicator
The dishwasher is equipped with an electric or visual salt level
indicator (depending on the model installed).
Electric indicator
The salt level indicator lamp on the control panel lights up when the
salt container is empty.
Visual indicator
The float is clearly visible in the cap window when the salt container
is full.
The float lowers and is no longer visible when the salt container is
empty.
15
HOW TO FILL THE RINSE AID DISPENSER
The rinse aid facilitates drying and prevents the formation of
unsightly spots and streaks on crockery. Before using the dishwasher
for the first time, fill the rinse aid dispenser. Only use rinse aids
recommended for use in domestic dishwashers.
1.
Press button
A
to open the cover (see drawing).
2.
Fill the dispenser with rinse aid up to the dashed line
(about 100 ml
maximum
).
Immediately wipe away any rinse aid spilt accidentally!
This
prevents the formation of excess suds which may spoil washing
results.
3.
Close the cover.
Thereafter, regularly check the rinse aid level.
How to adjust the rinse aid dosage regulator:
Factory setting: position 4.
If you are not satisfied with washing or drying results, change the
rinse aid dosage setting.
1.
Press button
A
to open the cover (see drawing).
2.
If crockery is prone to whitish streaks: reduce the dosage by
turning the dial to a lower setting (1-3) using a coin or the like.
If crockery is not perfectly dry: increase the dosage by turning the
dial to a higher setting (5-6).
3.
Close the cover.
Rinse aid level indicator:
Visual indicator:
light
add rinse aid
dark
sufficient rinse aid.
Do not add any!
Electric indicator (if provided):
The indicator lamp on the control panel lights up when more rinse aid
needs to be added.
A
17
CARE AND MAINTENANCE
Before cleaning or carrying out maintenance, switch off the
appliance, disconnect the mains plug and turn off the water tap.
Cleaning the outside of the appliance:
To clean the outside of the appliance, use a neutral detergent and a
damp cloth.
Clean the control panel with a damp cloth only.
Do not use abrasive detergents.
Cleaning the inside of the dishwasher:
Regularly wipe the door seal and inside of the door with a damp cloth
to remove any food residue.
Upper spray arm:
1.
Slacken the fixing nut (
A
) (by turning it counter-clockwise) and
detach the spray arm (
B
) by pulling it down).
2.
Rinse the nozzles.
3.
To remount the spray arm, align it and then tighten the fixing nut
(by turning it clockwise)
,
paying attention not to bend it.
The fixing nut must be tightened until it clicks!
Make sure the spray arm rotates freely.
Lower spray arm:
1.
Slacken the fixing nut (
C
) (by turning it counter-clockwise) and
detach the spray arm (
D
) by pulling it upwards.
2.
Rinse the nozzles.
3.
To remount the spray arm, align it and then tighten the fixing nut
(by turning it clockwise), paying attention not to bend it.
The fixing nut must be tightened until it clicks!
Make sure the spray arm rotates freely.
A
B
D
C
18
CARE AND MAINTENANCE
Cleaning the filters
1.
Rotate the microfilter counter-clockwise (in the direction of the
arrow
“0”
) and extract it (
E
).
2.
Place the microfilter/wide-mesh central filter unit on a flat
surface and push the handle of the microfilter (
F
).
Extract the wide-mesh filter by pushing it forward (
G
).
3.
Remove the fine-mesh filter (
H
).
4.
Clean all filters under running water,
paying attention not to bend
the fine-mesh filter. Check that no impurities are left inside the
dishwasher!
5.
Remounting:
Insert the wide-mesh filter in the microfilter (click should be
heard!) Insert the fine-mesh filter.
The filter must be fitted
under both tongues.
Insert the microfilter/wide-mesh central filter unit and turn
clockwise to lock (in the direction of arrow “1”), until the dashed
lines on the microfilter and fine-mesh filter are aligned.
The filter unit must be correctly assembled to ensure good
wash results!
H
E
G
F
19
20
5019 396 94111
Printed in Germany
1/0701
Ecological Paper
GB
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Whirlpool ADG 6966/1 IXM WP instrukcja
- Kategoria
- Zmywarki
- Typ
- instrukcja
- Niniejsza instrukcja jest również odpowiednia dla