2060/W
The 2060/W model incorporates a solenoid controlled electronic tape
deck and an internal receiver for use with a handheld, lapel or head-
band type wireless microphones operating on a fixed frequency. In all
other respects operation of this equipment is exactly the same as on
the 2060 model.
“Hard wired” mics (using a 6.3mm jack plug) such as the Coomber 1918 or
1808 models, may be used in conjunction with the radio microphone.
Alternatively, further radio microphone systems such as the Coomber
Diversity systems can also be used alongside the integral radio micro-
phone provided that they are of a different frequency. Please feel free
to phone for advice if required.
Using the Handheld radio microphone
1. Extend both aerials (1) on the 2060/W fully and
pull them away from each other.
2. Switch on the radio mic using the switch fitted
in the base. A red indicator light will glow to
indicate that the microphone is operating
correctly.
If the light does not glow, check the condition
of the battery and replace if necessary.
3. Depress the radio mic switch (2) and adjust volume
to suit.
Using a Lapel or Headband radio microphone
The lapel and headband microphones both use a bodypack in which a
transmitter is fitted. Begin by connecting the microphone and aerial
provided in the kit to the bodypack.
1. Extend aerial (1) on the 2060/W fully.
2. Switch on the microphone at the bodypack. A red indicator light
will glow to indicate that the transmitter is operating correctly.
If the light does not glow, check the condition of the bodypack
battery and replace if necessary.
3. Depress the radio mic switch (2) and adjust volume to suit.
Avoiding Feedback
Please refer to the 2020, 2060 Operating Instructions for guidance on
how to combat feedback problems.
Interference: Good Practice
It is always possible to pick up intereference from nearby radio trans-
mitters while the radio microphone receiver is switched on but unused
- especially if the radio mic itself is switched off. It is therefore good
practice to switch off the radio microphone receiver (12), if the radio
mic is not being used.
Logic Controlled Solenoid Tape Deck (3)
The advanced mechanism fitted to all 2060/W and 2020-2 models
works in the same way as the traditional mechanical deck, but with
these additional features.
1. Solenoid control allows the user to switch directly between
REWIND, FAST FORWARD and PLAY without needing to select
STOP first.
2. CUE and REVIEW, selected by pressing FAST FORWARD or REWIND
while in PLAY mode, allows the user to fast forward or rewind the
tape by a few seconds.
TIP: Gently tapping the appropriate key will allow the tape to go
forwards or backwards by 1.5 seconds. Holding the key down will
allow the tape to go forwards or backwards for as long as the key
is depressed. AS SOON AS THE KEY IS RELEASED THE TAPE WILL
BEGIN PLAYING AGAIN.
3. RECORD can only be selected from STOP. It cannot be selected
when the tape is in PLAY, FAST FORWARD or REWIND modes.
To record, press the RECORD key, followed by the PLAY key.
TIP: While in RECORD mode, REVIEW can be selected; though this
will automatically discontinue recording.
Important recordings can be protected by removing the appropriate
tape protection tab. If an attempt is made to use such a tape for
recording purposes, the record indicator light will flash three
times and RECORD will not be selected.
4. If all three indicator lights flash five times, then the cassette may
be loaded incorrectly. Without using undue force, eject the tape
and re-insert it before trying to play the tape again.
5. EJECT will only operate in the STOP and PAUSE modes. While the
tape is moving, the EJECT button remains locked and cannot be
used.
6. The tape deck accepts Normal and Chrome tapes. It monitors the
type of tape inserted and automatically selects Normal or Chrome
mode, providing optimum performance at all times.
7. The SEARCH facility looks for a gap of 3 seconds or more, allowing
the user to wind forwards or backwards to the start or finish of a
music track (for example).
To use this mode, select PLAY and then depress the PLAY key for a
second time. The PLAY LED will flash twice while the cassette continues
to play. Pressing either the FAST FORWARD or REWIND keys will
now initiate SEARCH mode.
To deselect the SEARCH facility, simply depress the PLAY key again.
This time, the PLAY LED will flash once.
STOP or end-of-tape automatically cancels the SEARCH mode.
Note: CUE and REVIEW will not operate in the SEARCH mode.
Supplementary Instructions: 2060/W & 2020-2 Coomber
Radio Microphones and the Logic Controlled Solenoid Tape Deck
BASSTAPE VOLUME
050100
23
1
2060/W instructions © Coomber Electronic Equipment Ltd. 2004 OPS 2060/W R4 210404
Coomber Electronic Equipment Ltd.
Brindley Road
Warndon
Worcester
WR4 9FB U.K.
Tel: 01905 342070 Int. Tel. +44 1905 342070
Fax: 01905 579170 Int. Tel. +44 1905 759170
Email: sales@coomber.co.uk
Web: www.coomber.co.uk
We reserve the right to make changes deemed necessary without prior notification.
2060/W top panel
-
1
Coomber 2060 Instrukcja obsługi
- Typ
- Instrukcja obsługi
- Ten podręcznik jest również odpowiedni dla
w innych językach
- English: Coomber 2060 User manual