TP-LINK TL-SG1210P Instrukcja instalacji

Marka: TP-LINK

Model: TL-SG1210P

Kategoria: Przełączniki sieciowe

Typ: Instrukcja instalacji

Installation Guide

Unmanaged Desktop PoE+ Switch

Switches Explanation

O: Ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m away.

On: Ports run at 10 Mbps and support PoE power supply up to 250 m away.

Extend (for TL-SG1008P/TL-SG1210P/TL-SG1210MP)

Connection

Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.

IP Camera AP

Ethernet Ports (1-8)

PoE Ports (1-4)

IP Phone

PoE Devices

Router

LAN PortWAN Port

Internet

DC Power Adapter

AC Power Cord

Note:

PoE ports can also connect to non-PoE devices, but only transmit data.

O: The PoE Auto Recovery function is disabled.

On: The switch will constantly detect the working status of a PoE powered device (PD).

When the switch nds that the PD works abnormally, the switch will reboot it.

Recovery (for TL-SG1008P/TL-SG1210P/TL-SG1210MP)

Note: The numbers in brackets indicate the ports where the feature takes eect. For example, when Extend(1-4) is toggled to On, the Extend mode will be enabled for ports 1-4.

O: Ports can transmit data with each other.

On: Specic ports cannot transmit data with other downlink ports. They can transmit data

only with the uplink ports.

Isolation (for TL-SG1210P/TL-SG1210MP)

O: All the ports transmit data with the same priority.

On: The specic ports transmit data with a higher priority than other ports.

Priority (for TL-SG1210P/TL-SG1210MP)

For TL-SG1210MP:

On: 116 W≤Total power supply < 123 W

Flashing: Total power supply ≥ 123 W

O: Total power supply < 116 W

LED Explanation

Power PoE Status

On: Providing PoE power

Flashing: PoE fault

O: Not providing PoE power

On: Power on

O: Power o

Link/Act; Uplink 1, Uplink 2

Green On:

Running at 1000 Mbps, but no activity.

Green Flashing:

Running at 1000 Mbps and is transmitting or

receiving data.

Yellow On:

Running at 10/100 Mbps, but no activity.

O:

No device is linked to the corresponding port.

Yellow Flashing:

Running at 10/100 Mbps and is transmitting

or receiving data.

PoE Max

For TL-SG1008P:

On: 57 W≤Total power supply < 64 W

Flashing: Total power supply ≥ 64 W

O: Total power supply < 57 W

For TL-SG1210P:

On: 56 W≤Total power supply < 63 W

Flashing: Total power supply ≥ 63 W

O: Total power supply < 56 W

Frequently Asked Questions (FAQ)

The Power LED should be lit when the power system is working normally. If the Power LED is

not lit, please check as follows:

A1:

Make sure the AC power cord is connected the switch with power source properly.

A2:

Make sure the voltage of the power supply meets the requirements of the input voltage

of the switch.

A3:

Make sure the power source is on.

Q1. The Power LED is not lit.

It is recommended that you check the following items:

A1:

Make sure that the cable connectors are rmly plugged into the switch and the device.

A2:

Make sure the connected device is turned on and working well.

A3:

The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it

should be less than 250 meters (820 feet).

Q2. Why is the Link/Act LED not lit while a device is connected to

the corresponding port?

For technical support and other information, please visit

https://www.tp-link.com/support, or simply scan the QR code.

To ask questions, find answers, and communicate with TP-Link users or

engineers, please visit https://community.tp-link.com to join TP-Link

Community.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service, please

Place the device with its bottom surface downward.

Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

TP-Link hereby declares that the device is in compliance with the essential requirements

and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and

(EU)2015/863.

The original EU declaration of conformity may be found at

https://www.tp-link.com/en/support/ce/

EU declaration of conformity

Specications

Q3. Why is PoE/PoE+ Port not supplying power for PoE devices?

When the total power consumption of connected PoE devices exceeds the maximum, the

PoE port with a smaller port number has a higher priority. The system will cut o power to

the ports with larger port numbers to ensure supplying to other ports.

Take TL-SG1008P as an example. If port 1, 2 and 4 are consuming 15.4 W respectively, and

an additional PoE device with 20 W is connected to port 3, the system will cut o the power

of port 4 to compensate for the overload.

IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x,

IEEE 802.3af, IEEE 802.3at, IEEE 802.1p

IEEE 802.3z (Only for TL-SG1210P/TL-SG1210MP)

CSMA/CD

For TL-SG1008P:

8 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;

PoE Ports: Port 1-4

For TL-SG1210P:

9 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;

1 1000 Mbps SFP port;

PoE Ports: Port 1-8

For TL-SG1210MP:

10 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX;

1 1000 Mbps SFP port (Combo);

PoE Ports: Port 1-8

10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);

EIA/TIA-568 100 Ω STP (maximum 100 m)

100BASE-TX: UTP

TP-LINK TL-SG1210P Instrukcja instalacji

Marka: TP-LINK

Model: TL-SG1210P

Kategoria: Przełączniki sieciowe

Typ: Instrukcja instalacji

ściągnij PDF

raport

w innych językach

English: TP-LINK TL-SG1210P Installation guide