Indesit ECO8D 1292 (EU) instrukcja

Kategoria
Pralki
Typ
instrukcja
GB
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine, 4-5
Control panel
Display
Running a wash cycle, 6
Wash cycles and functions, 7
Table of wash cycles
Wash functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 9
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 11
Service, 12
GB
ECO8D 1292
Instructions for use
WASHING MACHINE
BG
FR
ES
Français,13
Български,25
CZ
Español,37
PL
Česky,49
Polski,61
2
GB
Installation
! This instruction manual should be kept in a safe place for
future reference. If the washing machine is sold, transferred
or moved, make sure that the instruction manual remains
with the machine so that the new owner is able to familiari-
se himself/herself with its operation and features.
! Read these instructions carefully: they contain vital infor-
mation relating to the safe installation and operation of the
appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not been
damaged during the transportation process. If it has been
damaged, contact the retailer and do not proceed any
further with the installation process.
3. Remove the 4 protective
screws (used during tran-
sportation) and the rubber
washer with the correspon-
ding spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need them
again if the washing machine needs to be moved to ano-
ther location.
! Packaging materials should not be used as toys for
children.
Levelling
1. Install the washing machine on a flat sturdy floor, without
resting it up against walls, furniture cabinets or anything
else.
2. If the floor is not perfectly
level, compensate for any
unevenness by tightening or
loosening the adjustable front
feet (see figure); the angle
of inclination, measured in
relation to the worktop, must
not exceed 2°.
Levelling the machine correctly will provide it with stability,
help to avoid vibrations and excessive noise and prevent it
from shifting while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow a sufficient
ventilation space underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply pipe
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
Before performing the con-
nection, allow the water to
run freely until it is perfectly
clear.
2. Connect the inlet hose
to the washing machine by
screwing it onto the corre-
sponding water inlet of the
appliance, which is situa-
ted on the top right-hand
side of the rear part of the
appliance (see figure).
3. Make sure that the hose is not folded over or bent.
! The water pressure at the tap must fall within the values
indicated in the Technical details table (see next page).
! If the inlet hose is not long enough, contact a specialised
shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
GB
3
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a drai-
nage duct or a wall drain
located at a height between
65 and 100 cm from the
floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not be
underwater.
! We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150 cm
in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
the socket is earthed and complies with all applicable
laws;
the socket is able to withstand the maximum power load
of the appliance as indicated in the Technical data table
(see opposite);
the power supply voltage falls within the values indicated
in the Technical data table (see opposite);
the socket is compatible with the plug of the washing
machine. If this is not the case, replace the socket or the
plug.
! The washing machine must not be installed outdoors,
even in covered areas. It is extremely dangerous to leave
the appliance exposed to rain, storms and other weather
conditions.
! When the washing machine has been installed, the elec-
tricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced by autho-
rised technicians.
Warning! The company shall not be held responsible in the
event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before you use
it for the first time, run a wash cycle with detergent and no
laundry, using the wash cycle .
Technical data
Model
ECO8D 1292
Dimensions
width 59.5 cm
height 85 cm
depth 60 cm
Capacity
from 1 to 8 kg
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1200 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme
(90°C); temperature 60°C
(press the TEMPERATURE button);
using a load of 8 kg.
This appliance conforms to the following
EC Directives:
- 2004/108/EC (Electromagnetic Compa-
tibility)
- 2006/95/EC (Low Voltage)
- 2002/96/EC
4
GB
Detergent dispenser drawer: used to dispense deter-
gents and washing additives (see “Detergents and laundry”).
ON/OFF button : press this briefly to switch the machine
on or off. The START/PAUSE indicator light, which flashes
slowly in a green colour shows that the machine is switched
on. To switch off the washing machine during the wash cycle,
press and hold the button for approximately 2 seconds; if
the button is pressed briefly or accidentally the machine will
not switch off. If the machine is switched off during a wash
cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR buttons: used to set the desired
wash cycle (see “Table of wash cycles”).
MEMORY button: press and hold the button to store a
cycle with your own set of preferences in the memory of
the machine. To recall a previously stored cycle, press the
MEMORY button.
FUNCTION buttons: press the button to select the desired
function. The corresponding indicator light on the display
will switch on.
SPIN button : press to reduce or completely exclude the
spin cycle - the value is indicated on the display.
TEMPERATURE button : press to decrease the tempe-
rature: the value will be shown on the display.
CONTROL PANEL LOCK button : to activate the control
panel lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the control
panel is locked. This means it is possible to prevent wash
cycles from being modified accidentally, especially where
there are children in the home. To deactivate the control
panel lock, press and hold the button for approximately 2
seconds.
DELAYED START button : press to set a delayed start
time for the selected wash cycle. The delay time will be shown
on the display.
START/PAUSE button with indicator light: when the gre-
en indicator light flashes slowly, press the button to start a
wash cycle. Once the cycle has begun the indicator light will
remain lit in a fixed manner. To pause the wash cycle, press
the button again; the indicator light will flash in an orange
colour. If the symbol is not illuminated, the door may be
opened. To start the wash cycle from the point at which it
was interrupted, press the button again.
Standby mode
This washing machine, in compliance with new energy saving
regulations, is fitted with an automatic standby system which
is enabled after about 30 minutes if no activity is detected.
Press the ON-OFF button briefly and wait for the machine
to start up again.
Description of the washing
machine
Control panel
TEMPERATURE
Button
WASH
CYCLE
SELECTOR
Buttons
Detergent dispenser drawer
FUNCTION
buttons
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with
indicator light
CONTROL
PANEL
LOCK Button
DISPLAY
DELAYED
START Button
MEMORY
Button
GB
5
Display
The display is useful when programming the machine and provides a great deal of information.
The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-
tion relating to the progress status of the wash cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the
time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include
a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-
rature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.
Door locked symbol
If the symbol is lit, this indicates that the washing machine door is blocked to prevent it from being opened accidentally. To
prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.
N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by pressing the
START/PAUSE button if you wish to open it.
! The first time the machine is switched on, you will be asked to select the language and the display will automatically show
the language selection menu.
To select the desired language press the X and Y buttons; to confirm the selection press the Z button.
If you wish to change the selected language, simultaneously press and hold all the three buttons marked with an L in the
figure, until you hear a beep. Switch the machine on again; the language selection menu will be displayed.
A
B
C
D
E
F
Z
X
Y
L
F
F
6
GB
Running a wash cycle
1. SWITCH THE MACHINE ON. Press the button; the
text WELCOME will appear on the display and the START/
PAUSE indicator light will flash slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed
the maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in “Detergents
and laundry”.
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Press one of the WASH
CYCLE SELECTOR buttons to select the required wash
cycle; the name of the wash cycle will appear on the
display. A temperature and spin speed is set for each
wash cycle; these may be adjusted. The duration of the
cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed. The machine automatically selects the
maximum temperature and spin speed set for the
selected wash cycle; these values cannot therefore
be increased. The temperature can be decreased by
pressing the button, until the cold wash “OFF”
setting is reached. The spin speed may be progressively
reduced by pressing the button, until it is completely
excluded (the “OFF” setting). If these buttons are
pressed again, the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the symbol lights up on the
display. To remove the delayed start function press the
button until the text “OFF” appears on the display.
Modifying the cycle settings.
Press the button to enable the function; the indicator
light corresponding to the button will switch on.
Press the button again to disable the function; the
indicator light will switch off.
! If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash
and the function will not be activated.
! If the selected function is not compatible with
another function which has been selected previously,
the indicator light corresponding to the first function
selected will flash and only the second function will
be activated; the indicator light corresponding to the
enabled function will remain lit.
! The functions may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol will
be on). During the wash cycle, the name of the phase
in progress will appear on the display. To change a
wash cycle while it is in progress, pause the washing
machine using the START/PAUSE button (the START/
PAUSE indicator light will flash slowly in an orange
colour); then select the desired cycle and press the
START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text “END OF CYCLE” on the display;
when the DOOR LOCKED symbol switches off
the door may be opened. Open the door, unload the
laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun,
press and hold the button. The cycle will be stopped
and the machine will switch off.
GB
7
Wash cycles and functions
Wash functions
Stain removal
This function is particularly
useful for the removal of
stubborn stains. Place extra
compartment 3 (supplied) into
compartment 1. When pouring
in the bleach, be careful not
to exceed the max level
marked on the central pivot
(see figure). To run the bleach
cycle on its own, pour the
bleach into extra compartment
3, set the “Rinse” programme and activate the “Stain removal
programme. To bleach during a wash cycle, pour in the
detergent and any fabric softener you wish to use, set the
desired wash cycle and enable the “Stain removal” function.
! It cannot be used with the , , , , Pump out.
Extra rinse
By selecting this option, the efficiency of the rinse is increased
and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
! It cannot be used in conjunction with the , , “Pump
out” programmes.
Easy iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases.
For all Test Institutes:
(*) Test wash cycle in compliance with regulation EN 60456: set wash cycle
(90°C);
temperature 60°C (press the TEMPERATURE button).
(*) Long wash cycle for cottons: set wash cycle
(90°C);
temperature 40°C (press the TEMPERATURE button).
(**) Short wash cycle for cottons.
At the end of the cycle the washing machine will perform
slow rotations of the drum; the EASY IRON and START/
PAUSE indicator lights will flash (orange) and the text “END
OF CYCLE” will appear on the display. To end the cycle, press
the START/PAUSE button or the EASY IRON button. For the
Silk/Curtains cycle, the machine will end the cycle while
the laundry is soaking; the EASY IRON and START/PAUSE
indicator lights will flash (orange) and the text “STOP WITH
WATER” will appear on the display. To drain the water so
that the laundry may be removed, press the START/PAUSE
button or the EASY IRON button.
! It may not be used with the , , , , Pump out”
programmes.
Fast wash
Reduces the duration of the wash cycle, while making it
possible to save water and electricity.
! It cannot be used with the , , , , , programmes.
Eco wash
The Eco Wash function saves energy by not heating the
water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash
action and water optimisation ensure great wash results in the
same average time of a standard cycle. For the best washing
results we recommend the usage of a liquid detergent.
! It cannot be used with the “Mix 15’”, , , , ,
programmes.
M
AX
1
3
2
Table of wash cycles
��������� Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load
(kg)
Eco
wash
Cycle
duration
Wash Bleach
Fabric
softener
Everyday wash cycles (Daily)
The duration of the wash cycles can be checked
on the display.
Cottons (*): extremely soiled whites. 90° 1200
8 8
Cottons: heavily soiled whites and resistant colours. 60° 1200
8 8
Cottons (**): lightly soiled resistant colours. 40° 1200
8 8
Synthetics (1st press of the button): heavily soiled resistant colours. 60° 800
3,5 3
Synthetics (2nd press of the button): lightly soiled resistant colours. 40° 800
3,5 3
Mix 30' (1st press of the button): to refresh lightly soiled garments quickly (not suita-
ble for wool, silk and clothes which require washing by hand).
30° 800
-
3 3
Mix 15' (2nd press of the button) : to refresh lightly soiled garments quickly (not suita-
ble for wool, silk and clothes which require washing by hand).
30° 800
-
1,5 -
Special cycles / Memo
Baby cycle: heavily soiled delicate colours. 40° 800
4 -
M
Memory: allows for any wash cycle to be stored.
Silk/Curtains: for garments in silk and viscose, lingerie. 30° 0
-
2 -
Wool: for wool, cashmere, etc. 40° 600
-
2 -
Partial wash cycles
Fast Spin (1st press of the button) - 1200 - - - 8 -
Slow spin (2nd press of the button) - 800 - - - 3,5 -
Rinse (1st press of the button) - 1200 -
8 -
Pump out (2nd press of the button) - 0 - - - 8 -
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 3: Bleach
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites
• Empty all garment pockets and check the buttons.
• Do not exceed the listed values, which refer to the weight
of the laundry when dry:
Durable fabrics: max. 8 kg
Synthetic fabrics: max. 3,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 2 kg
Silk: max. 2 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Special wash cycles
Mix 30’: this wash cycle was designed to wash lightly soi-
led garments quickly: it lasts just 30 minutes and therefore
saves both energy and time. By selecting this wash cycle (
at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 3 kg.
M
AX
1
3
2
Mix 15’: this wash cycle was designed to wash lightly soi-
led garments quickly: it lasts just 15 minutes and therefore
saves both energy and time. By selecting this wash cycle (
at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of
1.5 kg.
Baby cycle: this wash cycle can be used to remove the
soiling typically caused by babies, while ensuring that all
detergent is removed from nappies in order to prevent the
delicate skin of babies from suffering allergies. The cycle
has been designed to reduce the amount of bacteria by
using a greater quantity of water and optimising the effect
of special disinfecting additives added to the detergent.
At the end of the wash cycle, the machine will slowly rotate
the drum to prevent the formation of creases; to end the
cycle press the START/PAUSE button.
Silk: use special wash cycle to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle .
Wool: is the only washing machine manufacturer to have
been awarded the prestigious Woolmark Platinum Care
endorsement (M.0508) by the Woolmark Company, which
means that all woollen garments may be washed in the
washing machine, even those which state “hand wash
only” on the label. Wash cycle therefore offers
complete peace of mind when washing woollen garments
in the washing machine (max. load 2 kg) and guarantees
optimal performance.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
GB
9
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
This appliance is not intended for use by persons (inclu-
ding children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concer-
ning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that
they do not play with the appliance.
This appliance was designed for domestic use only.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extremely
high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt to
repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local regu-
lations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the
normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimise the
recovery and recycling of the materials they contain and
reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product
reminds you of your obligation, that when you dispose of
the appliance it must be separately collected.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it
is not, remove excess water
using the drain hose, collec-
ting it in a bucket as indicated
in the figure.
3. using a screwdriver, remo-
ve the cover panel on the lo-
wer front part of the washing
machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
Consumers should contact their local authority or retailer
for information concerning the correct disposal of their
old appliance.
10
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system inside the washing
machine and help to prevent leaks.
Unplug the washing machine when cleaning it and du-
ring all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser drawer
Remove the dispenser by
raising it and pulling it out
(see figure).
Wash it under running wa-
ter; this operation should be
repeated frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes, small
items (such as coins or buttons) may fall into the pre-cham-
ber which protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washing machine (see
figure);
2. unscrew the lid by rota-
ting it anti-clockwise (see
figure): a little water may
trickle out. This is perfectly
normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are any
cracks, it should be replaced immediately: during the wash
cycles, water pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
1
2
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the text “NO WATER,
CHECK SUPPLY” appears on the
display).
The washing machine continuously
takes in and
drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The machine is locked and the display
flashes, indicating an
error code (e.g. F-01, F-..).
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Running a wash cycle”).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually (see “Wash cycles and functions”).
The EASY IRON function has been activated: To complete the wash cycle,
press the START/PAUSE button (see “Wash cycles and functions”).
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
FR
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Description du lave-linge, 16-17
Bandeau de commandes
Écran
Comment faire un cycle de lavage, 18
Programmes et fonctions, 19
Tableau des programmes
Fonctions de lavage
Produits lessiviels et linge, 20
Tiroir à produits lessiviels
Triage du linge
Programmes spéciaux
Système d’équilibrage de la charge
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Ouverture manuelle de la porte hublot
Entretien et soin, 22
Coupure de l’arrivée d’eau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels.
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Anomalies et remèdes, 23
Assistance, 24
FR
ECO8D 1292
Mode d’emploi
LAVE-LINGE
14
FR
Installation
! Conserver ce mode d’emploi pour pouvoir le consulter à
tout moment. En cas de vente, de cession ou de déména-
gement, veiller à ce qu’il suive toujours le lave-linge pour
que son nouveau propriétaire soit informé sur son mode
de fonctionnement et puisse profiter des conseils corre-
spondants.
! Lire attentivement les instructions: elles fournissent des
conseils importants sur l’installation, l’utilisation et la sécu-
rité de l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été endommagé
pendant le transport. S’il est abîmé, ne pas le raccorder et
contacter le vendeur.
3. Enlever les 4 vis de
protection servant au tran-
sport, le caoutchouc et la
cale, placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons plastique
fournis.
5. Conserver toutes ces pièces: il faudra les remonter en
cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide, sans l’ap-
puyer contre des murs, des meubles ou autre.
2. Si le sol n’est pas parfai-
tement horizontal, visser ou
dévisser les pieds de régla-
ge avant (voir figure) pour
niveler l’appareil; son angle
d’inclinaison, mesuré sur le
plan de travail, ne doit pas
dépasser 2°.
Une bonne mise à niveau garantit la stabilité de l’appareil
et évite qu’il y ait des vibrations, du bruit et des dépla-
cements en cours de fonctionnement. Si la machine est
posée sur de la moquette ou un tapis, régler les pieds de
manière à ce qu’il y ait suffisamment d’espace pour assu-
rer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de l’eau
1. Reliez le tuyau d’alimenta-
tion en le vissant à un robinet
d’eau froide à embout fileté
3/4 gaz (voir figure).
Faire couler l’eau jusqu’à ce
qu’elle soit limpide et sans
impuretés avant de raccorder.
2. Raccorder le tuyau
d’arrivée de l’eau au lave-
linge en le vissant à la prise
d’eau prévue, dans la partie
arrière en haut à droite (voir
figure).
3. Attention à ce que le tuyau ne soit pas plié ou écrasé.
! La pression de l’eau doit être comprise entre les valeurs
indiquées dans le tableau des Caractéristiques techniques
(voir page ci-contre).
! Si la longueur du tuyau d’alimentation ne suffit pas,
s’adresser à un magasin spécialisé ou à un technicien
agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
FR
15
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau d’éva-
cuation, sans le plier, à un
conduit d’évacuation ou
à une évacuation murale
placés à une distance du
sol comprise entre 65 et
100 cm;
ou bien l’accrocher à un
évier ou à une baignoi-
re, dans ce cas, fixer le
support en plastique fourni
avec l’appareil au robinet
(voir figure). L’extrémité
libre du tuyau d’évacuation
ne doit pas être plongée
dans l’eau.
! L’utilisation d’un tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument qu’il ait le même diamètre que le tuyau original
et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant, s’as-
surer que:
la prise est bien reliée à la terre et est conforme aux
réglementations en vigueur;
la prise est bien apte à supporter la puissance maximale
de l’appareil indiquée dans le tableau des Caractéristi-
ques techniques (voir ci-contre);
la tension d’alimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche du lave-linge.
Autrement, remplacer la prise ou la fiche.
! Le lave-linge ne doit pas être installé dehors, même à
l’abri, car il est très dangereux de le laisser exposé à la
pluie et aux orages.
! Après installation du lave-linge, la prise de courant doit
être facilement accessible.
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé que par
des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas de
non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil, effectuer
un cycle de lavage avec un produit lessiviel mais sans linge
et sélectionner le programme .
Caractéristiques techniques
Modèle
ECO8D 1292
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 60 cm
Capacité
de 1 à 8 kg
Raccordements
électriques
Voir la plaque signalétique appliquée sur la
machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar) pres-
sion minimale 0,05 MPa (0,5 bar) capacité
du tambour 62 litres
Vitesse d'essorage
jusqu'à 1200 tours minute
Programmes de
contrôle selon la
norme EN 60456
programme
(90°C); température 60°C;
(appuyer sur la touche TEMPÉRATURE)
effectué avec une charge de 8 kg.
Cet appareil est conforme aux Directives
Communautaires suivantes:
- 2004/108/CE (Compatibilité électroma-
gnétique)
- 2002/96/CE
- 2006/95/CE (Basse Tension)
16
FR
Tiroir à produits lessiviels: pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Tasto MARCHE/ARRÊT : appuyer brièvement sur la
touche pour allumer ou éteindre l’appareil. Le voyant vert
MISE EN MARCHE/PAUSE clignotant lentement indique
que la machine est allumée. Pour éteindre le lave-linge en
cours de lavage, appuyer sur la touche pendant au moins
2 secondes de suite ; une pression brève ou accidentelle
n’entraîne pas l’arrêt de l’appareil. L’arrêt de l’appareil
pendant un lavage annule le lavage en cours.
Touches SÉLECTEUR PROGRAMMES: pour sélection-
ner le programme désiré (voir “Tableau des programmes”).
Touche MEMO: maintenir la touche enfoncée pour mé-
moriser un cycle et les personnalisations préférées. Pour
retourner à un cycle précédemment mémorisé, appuyer
sur la touche MEMO.
Touches FONCTION: appuyer sur la touche pour sé-
lectionner la fonction désirée. Le voyant correspondant
s’affiche à l’écran.
Touche ESSORAGE : appuyer sur cette touche pour
diminuer la vitesse de l’essorage ou pour le supprimer
complètement - la valeur correspondante s’affiche à
l’écran.
Touche TEMPERATURE : appuyer pour diminuer
la température : la valeur correspondante est affichée à
l’écran.
Touche VERROUILLAGE TOUCHES : pour activer
le verrouillage des commandes, garder la touche enfoncée
pendant environ 2 secondes. Le symbole allumé
indique que le bandeau de commandes est verrouillé.
Ceci permet d’éviter toute modification involontaire des
programmes, surtout s’il y a des enfants à la maison.
Pour désactiver le verrouillage des commandes, garder la
touche enfoncée pendant environ 2 secondes.
Touche DÉPART DIFFÉRÉ : appuyer sur cette touche
pour sélectionner un départ différé pour le programme
choisi. Le retard est affiché à l’écran.
Touche avec voyant MISE EN MARCHE/PAUSE: quand
le voyant vert clignote lentement, appuyer sur la touche
pour démarrer un lavage. Une fois le cycle lancé, le voyant
passe à l’allumage fixe. Pour activer une pause de lava-
ge, appuyer à nouveau sur la touche ; le voyant passe à
l’orange et se met à clignoter. Si le symbole n’est pas
allumé, il est possible d’ouvrir le hublot. Pour faire redé-
marrer le lavage exactement à l’endroit de l’arrêt, appuyer
une nouvelle fois sur la touche.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est
équipée d’un système d’extinction automatique (veille)
activé après 30 environ minutes d’inutilisation. Appuyez
brièvement sur la touche MARCHE/ARRÊT et attendre que
la machine soit réactivée.
Description du lave-linge
Bandeau de commandes
Touche avec
voyant MISE
EN MARCHE/
PAUSE
Touche
TEMPÉRATURE
Touches
SÉLECTEUR
PROGRAMMES
Tiroir à produits lessiviels
Touches
FONCTION
Touche
MARCHE/ARRÊT
Touche
ESSORAGE
Touche
VERROUILLAGE
TOUCHES
Écran
Touche
DÉPART
DIFFÉRÉ
Touche
MEMO
FR
17
Écran
L’écran est utile pour programmer la machine et fournit de multiples renseignements.
Les deux chaînes supérieures A et B affichent : le programme de lavage sélectionné, la phase de lavage en cours et toutes
les indications relatives au déroulement du programme.
La chaîne C affiche le temps restant à la fin du cycle de lavage en cours et si un DÉPART DIFFÉRÉ a été sélectionné, le tem-
ps restant avant le démarrage du programme sélectionné.
La chaîne D affiche la valeur maximum de la vitesse d’essorage que la machine peut effectuer en fonction du programme
sélectionné ; si le programme ne prévoit pas d’essorage, la chaîne reste éteinte.
La chaîne E affiche la valeur maximale de la température qui peut être sélectionnée en fonction du programme choisi ; si le
programme ne prévoit pas la sélection de la température, la chaîne reste éteinte.
Les voyants F correspondent aux fonctions et s’allument quand la fonction programmée est compatible avec le programme
sélectionné.
Symbole verrouillage hublot
Le symbole allumé indique que le hublot est verrouillé pour éviter toute ouverture accidentelle. Pour éviter d’abîmer l’appareil,
attendre que le symbole s’éteigne avant d’ouvrir le hublot.
N.B.: si la fonction DÉPART DIFFÉRÉ est active, le hublot reste verrouillé, pour l’ouvrir mettre la machine en pause en appu-
yant sur la touche MISE EN MARCHE/PAUSE.
! À la première mise en service, un message s’affiche demandant de sélectionner la langue et l’écran entre automatiquement
dans le menu de sélection de la langue.
Pour choisir la langue désirée, appuyer sur les touches X et Y; pour confirmer la sélection, appuyer sur la touche Z.
Pour changer de langue, éteindre l’appareil, appuyer simultanément sur les trois touches indiquées par la référence L de la
figure jusqu’au signal sonore. Rallumer l’appareil, le menu de sélection de la langue s’affiche.
A
B
C
D
E
F
Z
X
Y
L
F
F
18
FR
Comment faire un cycle de lavage
1. METTRE L’APPAREIL SOUS TENSION. Appuyer
sur la touche , l’inscription BIENVENU s’affiche à
l’écran ; le voyant de MISE EN MARCHE/PAUSE passe
au vert et clignote lentement.
2. CHARGER LE LINGE. Ouvrir la porte hublot. Charger
le linge en faisant attention à ne pas dépasser la
quantité indiquée dans le tableau des programmes de la
page suivante.
3. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir et
placer le produit lessiviel dans les bacs correspondants
comme indiqué au paragraphe “Detersifs et linge”.
4. FERMER LE HUBLOT.
5. CHOISIR LE PROGRAMME. Appuyer sur l’une
des touches du SÉLECTEUR PROGRAMMES
pour sélectionner le programme désiré ; le nom du
programme est affiché à l’écran avec attribution d’une
température et d’une vitesse d’essorage qui peuvent
être modifiées. La durée du cycle s’affiche sur l’écran.
6. PERSONNALISER LE CYCLE DE LAVAGE.
Appuyer sur les touches correspondantes :
Modifier la température et/ou la vitesse
d’essorage. L’appareil sélectionne automatiquement
la température et la vitesse d’essorage maximales
prévues pour le programme sélectionné qui ne peuvent
par conséquent pas être augmentées. Par pression
sur la touche on peut diminuer progressivement
la température de lavage jusqu’à un lavage à froid
“OFF”. Par pression sur la touche on peut diminuer
progressivement la vitesse d’essorage jusqu’à sa
suppression totale “OFF”. Une autre pression sur les
touches ramènera les valeurs aux maximales prévues.
Sélectionner un départ différé.
Pour programmer le départ différé d’un programme
sélectionné, appuyer sur la touche correspondante jusqu’à
ce que le retard désiré soit atteint. Quand cette option est
active, le symbole s’affiche à l’écran. Pour annuler le
départ différé, appuyer sur la touche jusqu’à ce que
l’inscription OFF s’affiche à l’écran.
Modifier les caractéristiques
du cycle.
Appuyer sur la touche pour activer la fonction; le
voyant correspondant à la touche s’allume.
Appuyer de nouveau sur la touche pour désactiver la
fonction ; le voyant s’éteint.
! Si la fonction sélectionnée est incompatible avec le
programme sélectionné, le voyant se met à clignoter et
la fonction n’est pas activée.
! Si la fonction sélectionnée est incompatible avec une
autre fonction précédemment sélectionnée, le voyant
correspondant à la première fonction se met à clignoter
et seule la deuxième fonction est activée alors que le
voyant de la fonction activée s’allume.
! Les fonctions permettent de modifier le chargement
conseillé et/ou la durée du cycle de lavage.
7. DEMARRER LE PROGRAMME. Appuyer sur
la touche MISE EN MARCHE/PAUSE. Le voyant
correspondant s’allume en vert fixe et le hublot est
verrouillé (symbole HUBLOT VERROUILLÉ allumé).
Pendant le lavage, le nom de la phase en cours s’affiche
à l’écran. Pour modifier un programme lorsqu’un
cycle est en cours, mettre le lave-linge en pause en
appuyant sur la touche MISE EN MARCHE/PAUSE (le
voyant MISE EN MARCHE/PAUSE passe à l’orange
et clignote lentement) ; sélectionner le cycle désiré et
appuyer de nouveau sur la touche MISE EN MARCHE/
PAUSE.
Pour ouvrir la porte tandis qu’un cycle est en cours,
appuyer sur la touche MISE EN MARCHE/PAUSE ; si le
symbole HUBLOT VERROUILLÉ est éteint, on peut
ouvrir le hublot. Pour faire redémarrer le programme
exactement à l’endroit de l’arrêt, appuyer une nouvelle
fois sur la touche MISE EN MARCHE/PAUSE.
8. FIN DU PROGRAMME. Elle est signalée par
l’inscription “FIN DE CYCLE” qui s’affiche à l’écran;
quand le symbole HUBLOT VERROUILLÉ s’éteint,
on peut ouvrir le hublot. Ouvrir le hublot, vider le lave-
linge et éteindre l’appareil.
! Une pression prolongée sur la touche permet
d’annuler un cycle déjà lancé. Le cycle est interrompu et la
machine s’éteint.
FR
19
Programmes et fonctions
Fonctions de lavage
Anti-taches
Cette fonction est très utile
pour éliminer les taches les
plus résistantes. Monter le bac
supplémentaire 3 fourni avec
l’appareil. Au moment de verser
l’eau de Javel, attention à ne
pas dépasser le niveau max
indiqsur le pivot central (voir
figure). Pour n’effectuer qu’un
blanchissage, verser l’eau de
Javel dans le bac supplémentaire
3, sélectionner le programme “Rinçage” et activer la fonction “Anti-
taches”. Pour blanchir en cours de lavage, verser le produit lessiviel
et les additifs, lectionner le programme souhaiet activer la
fonction “Anti-taches”.
! Cette fonction n’est pas activable avec les programmes ,
, , , “Vidange”.
Super Rinçage
La sélection de cette option permet d’augmenter l’efficacité du
rinçage et d’éliminer totalement toute trace de lessive. Elle est
très utile pour les peaux particulièrement sensibles.
! Cette fonction n’est pas activable avec les programmes ,
, et “Vidange”.
Repassage facile
En cas de sélection de cette fonction, le lavage et l’essorage
seront dûment modifiés pour réduire la formation de plis. À la fin
du cycle de lavage, le lave-linge fait tourner le tambour lentement;
Pour tous les instituts qui effectuent ces tests :
(*) Programme de contrôle selon la norme EN 60456 : sélectionner le programme
(90°C) température 60°C; (appuyer sur la touche TEMPÉRATURE).
(*)
Programme coton long:
sélectionner le programme
(90°C) température 40°C; (appuyer sur la touche TEMPÉRATURE).
(**)
Programme coton court.
Tableau des programmes
le voyant de la fonction REPASSAGE FACILE et celui de MISE
EN MARCHE/PAUSE se mettent à clignoter (orange), l’inscription
“FIN DE CYCLE” s’affiche à l’écran. Pour compléter le cycle, il
faut appuyer sur la touche MISE EN MARCHE/PAUSE ou sur
la touche REPASSAGE FACILE. Pour le programme Soie
l’appareil arrive au bout du cycle en laissant le linge tremper,
le voyant REPASSAGE FACILE clignote et celui de MISE EN
MARCHE/PAUSE se mettent à clignoter (orange), l’inscription
“ARRET CUVE PLEINE” s’affiche à l’écran. Pour vidanger l’eau et
sortir le linge, appuyer sur la touche MISE EN MARCHE/PAUSE
ou sur la touche REPASSAGE FACILE.
! Cette option n’est pas activable avec les programmes , ,
, , et “Vidange”.
Rapide
Pour réduire la durée du cycle de lavage tout en permettant de
faire des économies d’eau et d’électricité.
! Cette fonction n’est pas activable avec les programmes ,
, , , , .
Eco Wash
La fonction Eco Wash permet d’économiser l’énergie puisque
l’eau utilisée pour la lessive n’est pas réchauffée : un plus pour
l’environnement et pour votre facture d’électricité. L’action
renforcée et l’optimisation de la consommation de l’eau
garantissent d’excellents résultats pour une durée moyenne
identique à celle d’un cycle standard. Pour de meilleurs
résultats en matière de lavage, utilisez une lessive liquide.
! Cette fonction n’est pas activable avec les programmes
“Mix 15’”, , , , , .
M
AX
1
3
2
Programmes
Description du Programme
Temp.
maxi.
(°C)
Vitesse
maxi
(tours
minute)
Produits lessiviels
Charge
maxi
(Kg)
Eco
wash
Durée
cycle
Lavage Javel
Assou-
plissant
Programmes pour tous les jours
La durée des programmes de lavage est contrôlable sur l’afficheur.
Coton (*): blancs extrêmement sales. 90° 1200
8 8
Coton: blancs et couleurs résistantes très sales. 60° 1200
8 8
Coton(**): blancs et couleurs délicates peu sales. 40° 1200
8 8
Synthetique (1° pression de la touche): couleurs résistantes très sales. 60° 800
3,5 3
Synthetique (2° pression de la touche): couleurs résistantes peu sales. 40° 800
3,5 3
Mix 30' (1° pression de la touche): pour rafraîchir rapidement du linge peu sale (ne convient pas
pour la laine, la soie et le linge à laver à la main).
30° 800
-
3 3
Mix 15' (2° pression de la touche): pour rafraîchir rapidement du linge peu sale (ne convient pas
pour la laine, la soie et le linge à laver à la main).
30° 800
-
1,5 -
Programmes Spéciaux/ Memo
Cycle Bebe: couleurs délicates très sales. 40° 800
4 -
M
Memo: permet de mémoriser un cycle de lavage quelconque.
Soie/Rideaux: pour linge en soie, viscose, lingerie. 30° 0
-
2 -
Laine: pour laine, cachemire, etc. 40° 600
-
2 -
Programmes partiaux
Essorage rapide (1° pression de la touche) - 1200 - - - 8 -
Essorage délicat (2° pression de la touche) - 800 - - - 3,5 -
Rinçage resistant (1° pression de la touche) - 1200 -
8 -
Vidange (2° pression de la touche) - 0 - - - 8 -
La durée du cycle indiquée sur l’écran ou dans la notice représente une estimation calculée dans des conditions standard. Le temps effectif peut varier en fonction de nombreux facteurs tels que :
température et pression de l’eau en entrée, température ambiante, quantité de lessive, quantité et type de charge, équilibrage de la charge, options supplémentaires sélectionnées.
20
FR
Produits lessiviels et linge
Tiroir à produits lessiviels
Un bon résultat de lavage dépend aussi d’un bon dosage
de produit lessiviel: un excès de lessive ne lave pas mieux,
il incruste l’intérieur du lave-linge et pollue l’environnement.
! Ne pas utiliser de lessives pour lavage à la main, elles
moussent trop.
Sortir le tiroir à produits
lessiviels et verser la lessive
ou l’additif comme suit.
bac 1: Lessive lavage (en poudre ou liquide)
Verser la lessive liquide juste avant la mise en marche.
bac 2: Additifs (assouplissant, etc.)
L’assouplissant ne doit pas déborder de la grille.
bac supplémentaire 3: Produit javelisé
Triage du linge
Trier correctement le linge d’après:
- le type de textile / le symbole sur l’étiquette.
- les couleurs: séparer le linge coloré du blanc.
Vider les poches et contrôler les boutons.
Ne pas dépasser les valeurs indiquées correspondant au
poids de linge sec :
Textiles résistants: 8 kg max.
Textiles synthétiques: 3,5 kg max.
Textiles délicats: 2 kg max.
Laine: 2 kg max.
Soie: 2 kg max.
Combien pèse le linge ?
1 drap 400-500 g
1 taie d’oreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette éponge 150-250 g
Programmes spéciaux
Mix 30’: spécialement conçu pour laver du linge peu sale en
un rien de temps: il ne dure que 30 minutes et permet ainsi de
faire des économies d’énergie et de temps. La sélection de ce
programme ( à 30°C) permet de laver ensemble des textiles
difrents (sauf laine et soie) en ne passant pas 3 kg de charge.
Mix 15’: spécialement conçu pour laver du linge peu sale en
un rien de temps: il ne dure que 15 minutes et permet ainsi
de faire des économies d’énergie et de temps. La sélection
de ce programme ( à 30°C) permet de laver ensemble des
textiles différents (sauf laine et soie) en ne dépassant pas 1,5
kg de charge.
M
AX
1
3
2
Babè: programme spécial, idéal pour le lavage des vête-
ments d’enfants souvent très sales, il élimine toute trace de
lessive du linge pour protéger leur peau délicate et éviter
tout risque d’allergie. Spécialement conçu pour diminuer
la charge bactérienne, ce cycle utilise une plus grande
quantité d’eau et optimise l’effet des additifs désinfectants
spécifiques ajoutés à la lessive.
En fin de lavage, l’appareil fait tourner le tambour lentement
pour éviter de froisser le linge. Pour compléter le cycle ap-
puyer sur la touche MISE EN MARCHE/PAUSE.
Soie: sélectionner le programme de lavage spécial pour
vêtements en soie. Il est conseillé d’utiliser une lessive spé-
ciale pour linge délicat.
Rideaux: pliez-les bien et glissez-les dans une taie d’oreiller
ou dans un sac genre filet. Sélectionner le programme .
Laine: est le seul lave-linge à avoir obtenu le prestigieux
label Woolmark Platinum Care (M.0508) déliv par The
Woolmark Company qui garantit le lavage à la machi-
ne de tous les tements en laine, y compris ceux qui
portent létiquette lavage à la main uniquement .
Grâce au programme on peut donc laver à la machi-
ne, en toute tranquillité, tous les vêtements en laine (max.
2 kg) avec des performances de lavage optimales.
Système d’équilibrage de la charge
Avant tout essorage, pour éviter toute vibration excessive et
répartir le linge de façon uniforme, le lave-linge fait tourner
le tambour à une vitesse légèrement supérieure à la vitesse
de lavage. Si au bout de plusieurs tentatives, la charge n’est
toujours pas correctement équilibrée, l’appareil procède à un
essorage à une vitesse inférieure à la vitesse normalement
prévue. En cas de déséquilibre excessif, le lave-linge préfère
procéder à la répartition du linge plutôt qu’à son essorage.
Pour une meilleure répartition de la charge et un bon équili-
brage, nous conseillons de mélanger de grandes et petites
pièces de linge.
1 / 1

Indesit ECO8D 1292 (EU) instrukcja

Kategoria
Pralki
Typ
instrukcja