Blaze King S.Z4946.SP Blower Kit for Clarity S.CL2714.SP Instrukcja obsługi

Marka
Blaze King
Model
S.Z4946.SP Blower Kit for Clarity S.CL2714.SP
Typ
Instrukcja obsługi
180-Z4946-SP v1.00 May 22, 2020
Manufactured By
Valley Comfort Systems Inc., 1290 Commercial Way, Penticton, BC, V2A 3H5, Canada
Phone: 250-493-7444 w Fax: 250-493-5833 w www.blazeking.com w [email protected]m
S.Z4946.SP BLOWER KIT
for Clarity S.CL2714.SP
(Standing Pilot)
CALIFORNIA PROPOSITION 65
WARNING: This product can expose you to chemicals including benzene, which is known to the
State of California to cause cancer and birth defects or other reproductive harm. For more information:
www.P65Warnings.ca.gov
The blower will only come on when the replace is up to temperature (approximately 10-15 minutes).
Blower speed control sequence is o , then maximum to minimum. The speed of the blower
can be decreased by turning the knob clockwise . The speed of the blower can be increased by
turning the knob counterclockwise. The blower will continue to operate after the burner is turned
o (approximately 15-20 minutes). To turn the blower o manually, turn the blower control knob
counterclockwise until it “clicks”.
NOTE: ENSURE POWER TO THE UNIT IS TURNED OFF DURING INSTALLATION. ENSURE
THE APPLIANCE IS TURNED OFF AND AT ROOM TEMPERATURE BEFORE INSTALLATION.
180-Z4946-SP v1.00 May 22, 2020
Page 2
S.Z4946.SP BLOWER KIT for S.CL2714.SP
S.Z4946.SP BLOWER INSTALLATION
1. If attached, lift face frame and safety screen up
and out, away from the appliance, and set it aside.
2. The blower may be installed prior to appliance
installment by removing the back blower access
cover. If the appliance is already installed go to
step 5.
3. Ax the blower to the access cover as shown, the
blower edge should be against the cover ange.
4. Feed blower wires and assembly through opening
and reattach the access cover.
5. Feed the power cord wires through the case hole.
6. Slide the loomex bushing into the case hole.
7. Rotate the loomex bushing so slots are oset.
180-Z4946-SP v1.00 May 22, 2020
Page 3
S.Z4946.SP BLOWER KIT for S.CL2714.SP
8. Remove the two screws holding the control panel
and dissconnect the switch wires from the valve..
9. Pull the control panel out in front of unit. Remove
the knob, nut, and washer from the rheostat.
10. Ax the rheostat to control panel, note the
alignment pin location.
11. Attach star washer, nut, and knob to rheostat post.
12. Connect the black “W” wire from the rheostat to
the white “W” wire from the power cord.
13. Fasten the ground from the power cord to the front
rebox leg.
14. Slide the blower in on the left side, beside the leg,
around to the back of the case, keep wires from
getting pinched or snagged.
180-Z4946-SP v1.00 May 22, 2020
Page 4
S.Z4946.SP BLOWER KIT for S.CL2714.SP
RHEOSTAT
SNAP DISC
BLOWER
POWER
CORD
M
F
F
M M
F
F
F
M
F
M
F
G
12" BLK WIRE 12" BLK WIRE
20" BLK WIRE
S.Z4946.SP - FAN KIT CL2714.SP
"B" LABEL
"B" LABEL
"W" LABEL"W" LABEL
15. Slide the snapdisk into the clip on the left hand
side of the rebox bottom panel.
16. Connect the black “B” wire from the blower to the
black “B” wire from the power cord.
17. Fasten the control panel back onto the leg.
18. Reconnect the switch wires to the valve.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Blaze King S.Z4946.SP Blower Kit for Clarity S.CL2714.SP Instrukcja obsługi

Marka
Blaze King
Model
S.Z4946.SP Blower Kit for Clarity S.CL2714.SP
Typ
Instrukcja obsługi
ściągnij PDF
raport

w innych językach

Inne dokumenty