Indesit XWA 71251 WWG EU instrukcja

Marka: Indesit

Model: XWA 71251 WWG EU

Kategoria: Pralki

Typ: instrukcja

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Load balancing system

Disposal

Description of the washing machine

and starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Push & Wash

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Troubleshooting, 11

Service, 12

Instructions for use

WASHING MACHINE

XWA 71251

English,1

Español,13

Polski,25

Română,37

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the inlet

hose by screwing it

to a cold water tap

using a 3/4 gas thre-

aded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the washing

machine by screwing

it onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the range of values indicated in the Technical

data table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, transferred or moved, make

sure that the instruction manual remains with

the machine so that the new owner is able to

familiarise himself/herself with its operation

and features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its

packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washing machine ne-

eds to be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furni-

ture cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drain duct or

a wall drain situated

between 65 and 100

cm from the floor;

alternatively, placed

it over the edge of a

basin, sink or tub, fa-

stening the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• the power supply voltage falls within the va-

lues indicated in the Technical data table (see

opposite);

• the socket is compatible with the plug of the

washing machine. If this is not the case, repla-

ce the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been instal-

led, the electricity socket must remain within

easy reach.

65 - 100 cm

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

Warning! The company shall not be held re-

sponsible in the event that these standards are

not observed.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle “Auto Clean” (see “Cleaning the

washing machine”).

Technical data

Model

XWA 71251

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 7 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

Programme 8:

Cotton Standard 60°.

Programme 9:

Cotton Standard 40°.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front of

the machine by first

pressing it in the cen-

tre and then pushing

downwards on both

sides until you can re-

move it (see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

• Unplug the washing machine when cleaning it

and during all maintenance work.

Cleaning the washing machine

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The washing machine has a “Auto Clean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards (2)

(see figure).

Wash it under running

water; this procedure

should be repeated fre-

quently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with re-

duced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

• The washing machine must only be used by adults, in accor-

dance with the instructions provided in this manual.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washing ma-

chine performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the washing machine on and off.

PUSH & WASH button: (see “Wash cycles”).

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE button: sets the temperature or the cold

wash cycle (see “Personalisation”).

SPIN button: sets the spin speed or exclude the spin cycle

completely (see “Personalisation”).

DELAY TIMER button: delays the start of the wash cycle

by up to 9 hours.

Press the button repeatedly until the indicator light corre-

sponding to the desired delay time turns on.

When the button is pressed for the fourth time, the option

will be deactivated.

N.B.: once the START/PAUSE button has been pressed,

the delay time can only be modified by decreasing it until

the set programme is launched.

! This option is available on all programmes.

WASH CYCLE PROGRESS

indicator light

s: used to

monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem-

porarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash orange,

while the indicator light for the current wash cycle phase

will remain lit in a fixed manner. If the DOOR LOCKED

indicator light is switched off, the door may be opened

(wait approximately 3 minutes).

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine and starting a wash cycle

Control panel

WASH CYCLE PROGRESS

indicator lights

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

DELAY TIMER

button

TEMPERATURE

button

SPIN

button

FUNCTION

buttons with

indicator lights

PUSH & WASH

button

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Per-

sonalisation”), after the wash cycle has been started the

indicator light corresponding to the selected delay period

will begin to flash:

As time passes, the remaining delay will be displayed and

the corresponding indicator light will flash:

The set programme will start once the selected time delay

has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be-

gun, the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected option is not compatible with another

previously selected option, the indicator light will flash

accompanied by a buzzer (3 beeps), and only the latter

option will be activated; the indicator light corresponding to

the activated option will turn on

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes).

To open the door during a running wash cycle, press the

START/PAUSE button; the door may be opened once the

DOOR LOCKED indicator light turns off.

Starting a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. Turn the washing machine on by pressing the ON/OFF

button. All the indicator lights will turn on for a few secon-

ds, then only the indicator lights relative to the selected

programme settings will remain lit and the START/PAUSE

indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the spin speed (see “Personalisation”).

6. Measure out the detergent and washing additives (see

“Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE

button and the corresponding indicator light will remain lit

in a fixed manner in green. To cancel the set wash cycle,

pause the machine by pressing the START/PAUSE button

and select a new cycle.

9. At the end of the wash cycle the END indicator light

will switch on. The door can be opened once the DOOR

LOCK indicator light turns off (wait approximately 3 mi-

nutes). Take out your laundry and leave the appliance door

ajar to make sure the drum dries completely. Switch the

washing machine off by pressing the ON/OFF button.

Wash

Rinse

Spin

Drain

End of wash cycle

END

Wash cycles

Table of wash cycles

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 1200 rpm. Maximum load 3,5 kg. (Cycle duration 50’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END indicator light turns on.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 8 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should

be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 9 with a temperature of 40°C.

3) Synthetic program along: set wash cycle 10 with a temperature of 40°C.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption

kWh

Total water lt

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Special

Sport

30° 600 -

 

- 3,5 - - - 55’

Dark

30° 800 -

 

- 4 - - - 70’

Anti-odour (Cotton)

60° 1000 -

 

- 3,5 - - - 110’

Anti-odour (Synthetic)

40° 1000 -

 

- 3,5 - - - 100’

Delicate

30° 0 -

 

- 1 - - - 80’

Wool: for wool, cashmere, etc. 40° 800 -

 

- 1,5 - - - 70’

Duvet: for down-stuffed garments. 30° 1000 -

 

- 2 - - - 110’

Standard

Cottons with Pre-wash: extremely soiled whites. 90° 1200

  

- 7 53 2,15 77 170’

Cotton Standard 60° (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1200 -

 

- 7 53 1,13 52,5 180’

Cotton Standard 40° (2): lightly soiled whites and delicate colours.

40° 1200 -

 

- 7 53 1,00 75 170’

Synthetic: heavily soiled resistant colours. 60° 800 -

 

- 3,5 46 0,79 46 110’

Synthetic (3): lightly soiled resistant colours. 40° 800 -

 

- 3,5 46 0,56 46 100’

Coloured

40° 1200 -

 

- 7 53 0,89 70 100’

Eco & Rapid

Cotton Standard 20°: lightly soiled whites and delicate colours. 20° 1200 -

 

- 7 - - - 170’

20’ Refresh

20° 800 -

 

- 1,5 - - - 20’

Rapid 60’

60° 1000 -

 

- 7 - - - 60’

Partials

Rinse/Bleach - 1200 - -

 

7 - - - 50’

Spin + Drain - 1200 - - - - 7 - - - 25’

Setting the temperature

Press the TEMPERATURE button to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash . The washing machine will automatically prevent you from

selecting a temperature which is higher than the maximum value set for each wash cycle.

! Exception: if the 8 programme is selected, the temperature can be increased up to a value of 90°C.

Setting the spin speed

Press the SPIN SPEED button to set the spin speed for the selected wash cycle.

The maximum spin speeds available for each wash cycle are as follows:

Wash cycles Maximum spin speed

Cottons 1200 rpm

Synthetics 800 rpm

Wool 800 rpm

The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .

The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed

set for each wash cycle.

Functions

The various wash functions available with this washing machine will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the

selected wash cycle.

Stain removal

This option allows for selecting the type of dirt so as to optimally adjust the cycle for removing the stains. The following types

of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages, for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of selected dirt.

! It cannot be used in conjunction with wash cycles 1-2-3-4-5-6-7-11-12-13-14- - .

Fast Forward

During a wash programme and under certain conditions, pressing this button allows for ending the wash programme after

only 20’ if necessary, by performing a brief rinse cycle followed by a spin cycle at maximum 800 rpm or lower, if reduced

manually during the programme customisation phase. In this case, washing and rinsing performance will be reduced. After

pressing the button, the relative indicator light turns on together with the indicator light of the rinse phase. If the selected

temperature is equal to 40° and/or the button is pressed during the initial phase of the programme, the “Fast Forward” option

lasts longer so that the detergent can dissolve properly and avoid damaging the fabrics. In this case, the rinse phase indica-

tor light flashes while the wash indicator light remains fixed until the necessary activation conditions are fulfilled. If less than

20’ remain of the wash programme, the option will be disabled.

! It cannot be used in conjunction with wash cycles 2-4-5-6-13-14- - .

Easy iron

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At the end

of the cycle the washing machine will perform slow rotations of the drum, while the EASY IRON and START/PAUSE indicator

lights will flash and the END led will remain lit in a fixed manner. To end the cycle, press the START/PAUSE button or the

EASY IRON button.

! It cannot be used in conjunction with wash cycles 1-3-5-13-14- - .

Extra Rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! It cannot be used in conjunction with wash cycles 2-4-13-14- .

Personalisation

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in fact

cause build up on the inside of your appliance and contri-

bute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispen-

ser drawer and pour in the

detergent or washing additi-

ve, as follows.

Compartment 1: Pre-wa-

sh detergent (powder)

Before pouring in the deter-

gent, make sure that extra

compartment 4 has been

removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the remo-

vable plastic partition A (supplied) be used for proper dosage.

If powder detergent is used, place the partition into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indica-

ted on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into com-

partment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Garments requiring special care

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use cycle 2 to wash dark-coloured garments. This

programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

Anti-odour: use programme 3 for washing garments with

bad odours (e.g. smoke, sweat, fried food). The program-

me is designed to remove bad odours while preserving the

fabric fibres. Synthetics fabrics or mixed loads should be

washed at 40°, and resistant cotton fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments. For washing Silk items and Curtains,

select the relevant cycle and activate the option (in

this case it will also be possible to enable the “Extra Rinse”

option); the machine will end the cycle with the laundry

soaked and the indicator light will flash. To drain the water

so that the laundry can be removed, press the START/

PAUSE button ro the option .

Wool: the wool wash cycle of this machine has been

tested and approved by The Woolmark Company for the

washing of wool containing garments labelled as “hand

wash” provided that the garments are washed according

to the instructions on the garment label and those issued

by the manufacturer of this washing machine. (M1126)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Duvet: to wash single duvets (the weight of which should

not exceed 2 kg), cushions or clothes padded with goose

down such as puffa jackets, use the special wash cycle

number 6. We recommend that duvets are placed in the

drum with their edges folded inwards (see figure) and that

no more than ¾ of the total volume of the drum is used.

To achieve the best results, we recommend that a liquid

detergent is used and placed inside the detergent dispen-

ser drawer.

Coloured: use this cycle 11 to wash bright coloured

clothes. The programme is designed to maintain bright

colours over time.

Cotton Standard 20° (programme 12) ideal for lightly

soiled cotton loads. The effective performance levels achieved

at cold temperatures, which are comparable to washing at

40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

20’ Refresh (programme 13) ideal for refreshing and

washing lightly soiled garments in a few minutes. It lasts

just 20 minutes and therefore saves both time and energy.

It can be used to wash different types of fabrics together

(except for wool and silk), with a maximum load of 1.5 kg.

Rapid 60’ (programme 14) is designed to wash moderately

soiled resistant cotton garments at 60° in an hour, with good

washing performance. For synthetic or mixed garments, we

recommend lowering the temperature down to 40°.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The washing machine continuously

takes in and drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The “Functions” indicator lights and the

“start/pause” indicator light flash, while

one of the “phase in progress” indicator

lights and the “door locked” indicator

light will remain lit in a fixed manner.

There is too much foam.

Push & Wash does not activate.

The programme lasts a lot less that

expected.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Personalisation”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The function is enabled: to complete the wash cycle, press the START/

PAUSE button (“Personalisation”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

• After switching on the machine a control other than Push & Wash was activa-

ted. Switch the machine off and press the Push & Wash button.

• The “Fast Forward” option was activated.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Español

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 16

Interrumpir el agua y la corriente eléctrica

Limpiar la lavadora

Limpiar el cajón de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 17

Seguridad general

Sistema de equilibrado de la carga

Eliminaciones

Descripción de la lavadora y comienzo

de un programa, 18-19

Panel de control

Pilotos

Poner en marcha un programa

Programas, 20

Push & Wash

Tabla de programas

Personalizaciones, 21

Seleccionar la temperatura

Seleccionar el centrifugado

Funciones

Detergentes y ropa, 22

Contenedor de detergentes

Ciclo de blanqueo

Preparar la ropa

Prendas especiales

Anomalías y soluciones, 23

Asistencia, 24

XWA 71251

Manual de instrucciones

LAVADORA

Instalación

! Es importante conservar este manual para

poder consultarlo en cualquier momento. En

caso de venta, de cesión o de traslado, veri-

fique que permanezca junto con la lavadora

para informar al nuevo propietario sobre el

funcionamiento y brindar las correspondientes

advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavadora.

2. Controle que la lavadora no haya sufri-

do daños durante el transporte. Si estuviera

dañada no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para el

transporte y la aran-

dela de goma con

el correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de plá-

stico suministrados con el aparato.

5. Conserve todas las piezas: cuando la la-

vadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los

niños.

Nivelación

1. Instale la lavadora sobre un piso plano y

rígido, sin apoyarla en las paredes, muebles ni

en ningún otro aparato.

2. Si el piso no está

perfectamente hori-

zontal, compense las

irregularidades desen-

roscando o enroscan-

do las patas delante-

ras (ver la figura); el

ángulo de inclinación

medido sobre la su-

perficie de trabajo, no

debe superar los 2º.

Una cuidadosa nive-

lación brinda estabilidad a la máquina y evita

vibraciones, ruidos y desplazamientos durante

el funcionamiento. Cuando se instala sobre

moquetas o alfombras, regule los pies para

conservar debajo de la lavadora un espacio

suficiente para la ventilación.

Conexiones hidráulicas y eléctri-

cas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo

de tubo enroscándolo

a un grifo de agua fría

con la boca roscada

de 3/4 gas (ver la

figura).

Antes de conectarlo,

haga correr el agua

hasta que esté límpi-

da.

2. Conecte el tubo de

alimentación a la lava-

dora enroscándolo en

la toma de agua cor-

respondiente ubicada

en la parte posterior

derecha (arriba) (ver la

figura).

3. Controle que en el tubo no hayan pliegues

ni estrangulaciones.

! La presión de agua del grifo debe estar com-

prendida dentro de los valores contenidos en

la tabla de Datos técnicos (ver la página corre-

spondiente).

! Si la longitud del tubo de alimentación no es

la suficiente, diríjase a un negocio especializa-

do o a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

Conexión del tubo de desagüe

Conecte el tubo de

desagüe, sin plegar-

lo, a un conducto de

desagüe o a una de-

sagüe de pared ubi-

cados a una distancia

del piso comprendida

entre 65 y 100 cm.;

o apóyelo en el

borde de un lavama-

nos o de una bañe-

ra, uniendo la guía

suministrada con el

aparato, al grifo (ver

la figura). El extre-

mo libre del tubo de

desagüe no debe

permanecer sumer-

gido en el agua.

! No se aconseja utilizar tubos de prolonga-

ción, si fuera indispensable hacerlo, la prolon-

gación debe tener el mismo diámetro del tubo

original y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

• la toma tenga la conexión a tierra y haya sido

hecha según las normas legales;

• la toma sea capaz de soportar la carga máxima

de potencia de la máquina indicada en la tabla

de Datos técnicos (ver al costado);

• la tensión de alimentación esté comprendida

dentro de los valores indicados en la tabla de

Datos técnicos (ver al costado);

• la toma sea compatible con el enchufe de la

lavadora. Si no es así, sustituya la toma o el

enchufe.

! La lavadora no debe ser instalada al aire libre,

ni siquiera si el lugar está reparado, ya que es

muy peligroso dejarla expuesta a la lluvia o a

las tormentas.

! Una vez instalada la lavadora, la toma de cor-

riente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones múl-

tiples.

65 - 100 cm

! El cable no debe estar plegado ni sufrir com-

presiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso,

realice un ciclo de lavado con detergente y sin

ropa, seleccionando el programa “Auto Lim-

pieza” (ver “Limpiar la lavadora”).

Datos técnicos

Modelo

XWA 71251

Dimensio-

nes

ancho 59.5 cm

altura 85 cm

profundidad 54 cm

Capacidad

de 1 a 7 kg

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima

1 MPa (10 bar)

presión mínima

0,05 MPa (0,5 bar)

capacidad del cesto 52 litros

Velocidad

de centrifu-

gado

máxima 1200 r.p.m.

Programas

de control

según las

directivas

1061/2010 y

1015/2010

programa 8;

Algodón Standard 60ºC.

programa 9;

Algodón Standard 40ºC.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 2004/108/CE (Compatibili-

dad Electromagnética)

- 2012/19/EU

- 2006/95/CE (Baja Tensión)

Mantenimiento y cuidados

Limpiar la bomba

La lavadora posee una bomba autolimpiante

que no necesita mantenimiento. Pero puede

suceder que objetos pequeños (monedas,

botones) caigan en la precámara que prote-

ge la bomba, situada en la parte inferior de la

misma.

! Verifique que el ciclo de lavado haya termina-

do y desenchufe la máquina.

Para acceder a la precámara:

1. quite el panel de

cobertura delantero

de la máquina pre-

sionando hacia el

centro, luego empuje

hacia abajo desde

ambos costados y

extráigalo (ver las

figuras).

2. desenrosque la

tapa girándola en

sentido antihorario

(ver la figura): es nor-

mal que se vuelque

un poco de agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando, antes

de empujarlo hacia la máquina, que los gan-

chos se hayan introducido en las correspon-

dientes ranuras.

Controlar el tubo de alimentación

de agua

Controle el tubo de alimentación al menos

una vez al año. Si presenta grietas o rajaduras

debe ser sustituido: durante los lavados, las

fuertes presiones podrían provocar roturas

imprevistas.

! No utilice nunca tubos ya usados.

Interrumpir el agua y la corriente

eléctrica

• Cierre el grifo de agua después de cada lavado.

De este modo se limita el desgaste de la

instalación hidráulica de la lavadora y se

elimina el peligro de pérdidas.

• Desenchufe la máquina cuando la debe

limpiar y durante los trabajos de manteni-

miento.

Limpiar la lavadora

• La parte externa y las partes de goma se

pueden limpiar con un paño embebido en

agua tibia y jabón. No use solventes ni pro-

ductos abrasivos.

• La lavadora posee un programa de “Auto

Limpieza” de su interior que se debe realizar

sin ningún tipo de carga en el cesto.

El detergente (en un 10% de la cantidad acon-

sejada para prendas poco sucias) o algunos

aditivos específicos para la limpieza de la ropa

se podrán utilizar como coadyuvantes en el

programa de lavado. Se aconseja efectuar el

programa de limpieza cada 40 ciclos de lava-

do.

Para activar el programa pulse simultáneamente

los botones A y B durante 5 segundos (ver la fi-

gura). El programa comenzará automáticamente

y tendrá una duración de 70 minutos aproxima-

damente. Para detener el ciclo presione el botón

START/PAUSE.

Limpiar el cajón de detergentes

Para extraer el cajón,

presione la palanca (1)

y tire hacia afuera (2)

(ver la figura).

Lávelo debajo del agua

corriente, esta limpieza

se debe realizar fre-

cuentemente.

Cuidar la puerta y el cesto

• Deje siempre semicerrada la puerta para

evitar que se formen malos olores.

Precauciones y consejos

! La lavadora fue proyectada y fabricada en conformidad

con las normas internacionales de seguridad. Estas adver-

tencias se suministran por razones de seguridad y deben

ser leídas atentamente.

Seguridad general

• Este aparato ha sido fabricado para un uso de tipo

doméstico exclusivamente.

• Este aparato puede ser utilizado por niños de

8 años o más y por personas con capacidades

físicas, sensoriales o mentales disminuidas o

con experiencia y conocimientos insuficientes

siempre que sean supervisados o que hayan

recibido una adecuada formación sobre el uso

del aparato en forma segura y conozcan los

peligros derivados del mismo. Los niños no

deben jugar con el aparato. El mantenimiento

y la limpieza no deben ser realizados por niños

sin supervisión.

• La lavadora debe ser utilizada sólo por personas adul-

tas y siguiendo las instrucciones contenidas en este

manual.

• No toque la máquina con los pies desnudos ni con las

manos o los pies mojados o húmedos.

• No desenchufe la máquina tirando el cable, sino toman-

do el enchufe.

• No abra el cajón de detergentes mientras la máquina

está en funcionamiento.

• No toque el agua de descarga ya que puede alcanzar

temperaturas elevadas.

• En ningún caso fuerce la puerta: podría dañarse el

mecanismo de seguridad que la protege de aperturas

accidentales.

• En caso de avería, no acceda nunca a los mecanismos

internos para intentar una reparación.

• Controle siempre que los niños no se acerquen a la

máquina cuando está en funcionamiento.

• Durante el lavado, la puerta tiende a calentarse.

• Si debe ser trasladada, deberán intervenir dos o más

personas, procediendo con el máximo cuidado. La

máquina no debe ser desplazada nunca por una sola

persona ya que es muy pesada.

• Antes de introducir la ropa controle que el cesto esté

vacío.

Sistema de equilibrado de la carga

Antes de cada centrifugado, para evitar vibraciones exce-

sivas y para distribuir la carga de modo uniforme, el cesto

realiza rotaciones a una velocidad ligeramente superior a la

del lavado. Si después de varios intentos, la carga todavía

no está correctamente equilibrada, la máquina realiza el

centrifugado a una velocidad inferior a la prevista. Cuan-

do existe un excesivo desequilibrio, la lavadora realiza la

distribución antes que el centrifugado. Para obtener una

mejor distribución de la carga y su correcto equilibrado, se

aconseja mezclar prendas grandes y pequeñas.

Eliminaciones

• Eliminación del material de embalaje:

respete las normas locales, de ese modo, los embalajes

podrán volver a ser utilizados.

• La norma Europea 2012/19/EU sobre la eliminación de

aparatos eléctricos y electrónicos, indica que los elec-

trodomésticos no deben ser eliminados de la misma

manera que los desechos sólidos urbanos.

Los aparatos en desuso se deben recoger separada-

mente para optimizar el porcentaje de recuperación y

reciclaje de los materiales que los componen e impedir

potenciales daños para la salud y el medio ambiente. El

símbolo de la papelera tachada se encuentra en todos

los productos para recordar la obligación de recolección

separada. Para mayor información sobre la correcta eli-

minación de los electrodomésticos, los poseedores de

los mismos podrán dirigirse al servicio público respon-

sable o a los revendedores.

Contenedor de detergentes: para cargar detergentes

y aditivos (ver “Detergentes y ropa”).

Botón de ON/OFF: para encender y apagar la lavadora.

Botón PUSH & WASH: (ver “Programas”).

Mando de PROGRAMAS: para elegir los programas.

Durante el funcionamiento del programa el mando no se

mueve.

Botones con pilotos de FUNCIÓN: para seleccionar las

funciones disponibles. El piloto correspondiente a la fun-

ción seleccionada permanecerá encendido.

Botón TEMPERATURA: para seleccionar la temperatura

o el lavado en frío (ver “Personalizaciones”).

Botón CENTRIFUGADO: para seleccionar el centrifuga-

do o excluirlo (ver “Personalizaciones”).

Botón COMIENZO RETRASADO

Retrasa la puesta en marcha de la máquina hasta 9 horas.

Presione varias veces el botón hasta hacer encender el

piloto correspondiente al retraso deseado. La cuarta vez

que se presione el botón, la opción se desactivará.

Nota: Una vez presionado el botón START/PAUSE, se

puede modificar el valor del retraso sólo disminuyéndolo

hasta que se ponga en marcha el programa seleccionado.

! Se puede utilizar con todos los programas.

Pilotos DE AVANCE DEL CICLO: para seguir el estado

de avance del programa de lavado.

El piloto encendido indica la fase en curso.

Piloto PUERTA BLOQUEADA: para saber si la puerta se

puede abrir (ver la página correspondiente).

Botón con piloto START/PAUSE: se utiliza para poner en

marcha los programas o interrumpirlos momentáneamente.

Nota: Presione este botón para poner en pausa el lavado

en curso, el piloto correspondiente centelleará con color

anaranjado mientras que el de la fase en curso permane-

cerá encendido en forma fija. Si el piloto PUERTA BLO-

QUEADA está apagado, se podrá abrir la puerta (espere

3 minutos aproximadamente).

Para que el lavado se reanude a partir del momento en el

cual fue interrumpido, presione nuevamente este botón.

Modalidad de stand by

Esta lavadora está en conformidad con las nuevas norma-

tivas vinculadas al ahorro energético. Está dotada de un

sistema de auto-apagado (stand by) que, en caso de no

funcionamiento, se activa aproximadamente 30 minutos.

Presionar brevemente el botón ON-OFF y esperar que la

máquina se active.

Descripción de la lavadora y

comienzo de un programa

Botón con

piloto

START/PAUSE

Panel de control

Pilotos DE AVANCE DEL CICLO

Botón ON/OFF

Botón

COMIENZO

RETRASADO

Contenedor de detergentes

Mando de

PROGRAMAS

Botones con pilotos

FUNCIÓN

Piloto PUERTA

BLOQUEADA

Botón

TEMPERATURA

Botón

CENTRIFUGADO

Botón

PUSH & WASH

Pilotos

Los pilotos suministran información importante.

He aquí lo que nos dicen:

Comienzo retrasado

Si se ha activado la función “Comienzo retrasado” (ver “Per-

sonalizaciones”), después de haber puesto en marcha el

programa, comenzará a centellear el piloto correspondien-

te al retraso seleccionado:

Con el transcurrir del tiempo se visualizará el retraso resi-

dual con el centelleo de la luz testigo correspondiente:

Una vez transcurrido el tiempo de retraso seleccionado,

comenzará el programa.

Pilotos fase en curso

Una vez seleccionado y puesto en marcha el ciclo de

lavado deseado, las luces testigo se encenderán progresi-

vamente para indicar su estado de avance:

Botones de función y pilotos correspondientes

Seleccionando una función, el piloto correspondiente se

iluminará. Si la función seleccionada no es compatible con

el programa elegido, el piloto correspondiente centelleará

y la función no se activará. Si la opción seleccionada no

es compatible con otra opción elegida anteriormente, la

incompatibilidad se indicará con el centelleo del piloto y

una señal sonora (3 sonidos) y se activará sólo la segunda

opción, el piloto de la opción activada se iluminará.

Piloto puerta bloqueada

El piloto encendido indica que la puerta está bloquea-

da impidiendo su apertura; para poder abrir la puerta es

necesario que dicho piloto esté apagado (espere 3 minutos

aproximadamente). Para abrir la puerta mientras un ciclo

está en curso, presione el botón START/PAUSE; si el piloto

PUERTA BLOQUEADA está apagado, será posible abrir la

puerta.

Poner en marcha un programa

Programación rápida

1. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,

cuidando no superar la cantidad de carga indicada en la

tabla de programas de la página siguiente.

2. DOSIFICAR EL DETERGENTE. Extraiga el cajón y

vierta el detergente en las cubetas correspondientes

como se explica en “Detergentes y ropa”.

3. CERRAR LA PUERTA.

4. Pulsar el botón “PUSH & WASH” para poner en marcha

el programa de lavado.

Programación tradicional

1. Encienda la lavadora pulsando el botón ON-OFF. Todos

los pilotos se encenderán durante algunos segundos, lue-

go permanecerán encendidos sólo los pilotos correspon-

dientes a las configuraciones para el programa selecciona-

do y centelleará el piloto START/PAUSE.

2. Cargue la ropa y cierre la puerta.

Lavado

Aclarado

Centrifugado

Descarga

Fin del Lavado

END

3. Seleccione el programa deseado con el mando de

PROGRAMAS.

4. Fije la temperatura de lavado (ver “Personalizaciones”).

5. Fije la velocidad de centrifugado (ver “Personalizaciones”).

6. Vierta detergente y aditivos (ver “Detergentes y ropa”).

7. Seleccione las funciones deseadas.

8. Ponga en marcha el programa presionando el botón

START/PAUSE y el piloto correspondiente permanecerá

encendido, fijo y de color verde. Para anular el ciclo selec-

cionado ponga en pausa la máquina presionando el botón

START/PAUSE y elija un nuevo ciclo.

9. Al final del programa se iluminará el piloto . Cuando

el piloto PUERTA BLOQUEADA se apague, será posible

abrir la puerta (espere 3 minutos aproximadamente).

Extraiga la ropa y deje la puerta semicerrada para permitir

que el cesto se seque. Apague la lavadora presionando el

botón ON/OFF.

Programas

Tabla de programas

Push & Wash

Esta función permite poner en marcha un ciclo de lavado incluso con la máquina apagada sin tener que presionar anterior-

mente el botón ON/OFF o, después de encender la máquina, sin accionar ningún otro botón y/o mando (de lo contrario

el programa Push & Wash será desactivado). Para poner en marcha el ciclo Push & Wash mantenga presionado el botón

durante 2 segundos. El piloto encendido indica que el ciclo está en marcha. El ciclo de lavado es ideal para prendas de

algodón y sintéticas, funcionando a una temperatura de lavado de 30° y una velocidad máxima de centrifugado de 1200

revoluciones al minuto. Carga máx. 3,5 kg. (Duración del ciclo 50’).

¿Cómo funciona?

1. Cargue la ropa (prendas de algodón y/o sintéticas) y cierre la puerta.

2. Vierta el detergente y los aditivos.

3. Ponga en marcha el programa manteniendo presionado durante 2 segundos el botón Push & Wash. El piloto correspon-

diente se iluminará de color verde y la puerta se bloqueará (símbolo puerta bloqueada encendido).

N.B.: La puesta en marcha del lavado a través del botón Push & Wash activa un ciclo automático recomendado para algo-

dón y sintéticos no personalizable. Este programa no permite seleccionar otras opciones.

Para abrir la puerta mientras el ciclo automático está en curso, presione el botón START/PAUSE; si el símbolo puerta blo-

queada está apagado, será posible abrir la puerta. Presione nuevamente el botón START/PAUSE para reanudar el programa

a partir del momento en el que se había interrumpido.

4. Al final del programa se iluminará el piloto END.

La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede variar en función

de numerosos factores como la temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente, la cantidad y el tipo de carga, el equili-

brado de la carga y las opciones adicionales seleccionadas.

1) Programa de control según la directiva 1061/2010: seleccione el programa 8 con una temperatura de 60ºC.

Este ciclo es adecuado para limpiar una carga de algodón normalmente sucia, es el más eficiente en lo que se refiere al consumo combinado con la energía y la cantidad de agua y se usa con

prendas lavables a 60ºC. La temperatura efectiva de lavado puede diferir de la indicada.

2) Programa de control según la directiva 1061/2010: seleccione el programa 9 con una temperatura de 40ºC.

Este ciclo es adecuado para limpiar una carga de algodón normalmente sucia, es el más eficiente en lo que se refiere al consumo combinado con la energía y la cantidad de agua y se usa con

prendas lavables a 40ºC . La temperatura efectiva de lavado puede diferir de la indicada.

Para todos los Test Institutes:

2) Programa algodón largo: seleccione el programa 9 con una temperatura de 40ºC.

3) Programa sintético largo: seleccione el programa 10 con una temperatura de 40ºC.

Programas

Descripción del Programa

Temp. max.

(°C)

Velocidad

máx.

(r.p.m.)

Detergentes