Storm System 418D145-1 Instrukcja instalacji

Typ
Instrukcja instalacji
Product Description:
Storm System Acrylic Stain w/ Enduradeck Technology is a low sheen finish designed for use on decks and other
exposed flat areas as well as vertical siding, fences and railings that are subjected to the rigors of drastic weather and
temperature conditions, abrasion, acid rain or snow. This high hiding stain provides maximum protection against water,
ultra violet rays and general atmospheric contamination. This stain resists cracking, peeling and blistering and can be
used on new wood, previously stained wood, properly pressure treated wood, and composite decking. This stain
contains a unique rust inhibitor to retard nail and screw head rusting.
Precautions:
All floor coatings are more slippery when the surface becomes wet or contaminated with debris. To help reduce the
potential for slipping, coated areas must be kept dry and properly cleaned of dirt, oils, food and beverage residue,
water, snow, ice and any other contaminants.
Architectural Specifications:
For decks and fences:
Unfinished wood - Best application
▪ 1 coat of 523XX Quick Dry Oil Primer + 1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series
Acceptable Application
▪ 1 coat Acrylic Stain w/ Enduradeck Technology 418 Series thinned 10-20% with water + 1 coat of Acrylic Stain w/
Enduradeck Technology 418 Series unthinned
Previously stained decks and fences
▪ 1 or 2 coats of Acrylic Stain w/ Enduradeck Technology 418 Series
For Composite Decking
1 coat Storm System Quick Dry Oil Primer 523XX + 1 coat of Acrylic Stain w/ Enduradeck Technology
418 Series.
For siding and vertical surfaces
Unfinished wood (where extractive bleeding may occur) - Best application
▪ 1 coat of Storm System™ Quick Dry Oil Primer 523XX + 1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series
Acceptable application (Where bleeding type wood is not a concern)
1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series thinned with 10-20% water followed by 1 coat of Acrylic
Stain w/ Enduradeck Technology 418 Series
Previously stained wood
Application:
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect
yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lead.
Surface Preparation:
Surfaces must be thoroughly clean and dry. Always test a small area before application to the entire surface. All
mildewed areas should be cleaned with Storm System All Surface Mold & Mildew Stain Remover. New pressure
treated wood should be scrubbed with Storm System All Surface Cleaner to remove all surface deposits. Rinse
thoroughly and allow to dry.
All surfaces must be free of loose wood fibers before any application.
Stir thoroughly before and during application to insure uniform appearance. Material should be intermixed by pouring
into a large container and stirring before painting large areas, to insure color uniformity. On bare wood, thin the first
coat with approximately one pint water per gallon, then apply 1 or 2 unthinned finish coats. Apply evenly with a quality
nylon or synthetic brush maintaining a wet edge. Start at the end of boards and go along surfaces to a break point to
avoid lapping. If spraying, back brush immediately. This product may also be applied by roller or pad applicator.
Clean tools and equipment immediately with warm soapy water.
New pressure treated wood must be thoroughly cleaned with Storm System All Surface Cleaner, rinsed clean and
allowed to dry completely, or allowed to weather for six months, prior to staining. Light colors may have a green cast
for a few months as the preservatives leach from the wood. Decking Stain colors vary with the different varieties of
wood. Samples should be tested on the actual wood being used before large areas of wood are stained.
Recommended Use:
Sundecks, railings and posts, fences, benches, trellis, wood walkways, open porches, wood screening, patios, garden
enclosures, outdoor furniture, siding and composite decking.
Safety Information:
Keep out of reach of children. Do not take internally. Close container after each use.
Acrylic Stain w/ Enduradeck® Technology
418 Series
4/10/2017
STORM SYSTEM™
California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141
5/16/2013
Exterior
Type:
Alkyd Modified Acrylic
8
Volume Solids:
38.8
@ 60°
%
Solids by Weight:
52.1
%
Dry Film Thickness:
1.9
mils
Vehicle:
73.0
%
Pigment:
27.0
%
Viscosity @ 77 °F:
87
KU
Maximum VOC:
100
g/liter
Flash Pt °F:
Non-combustible
Thinner:
Water
Product Specifications:
Exposure:
Exterior
(Weight Per Gallon:
10.7
Available Package Sizes:
To Handle:
6
To Recoat:
4
hrs.
hrs.
hrs.
To Touch:
1
Drying Times:
lbs. ± .5 lb)
Surface Spread Rate:
s.f./gal.
(Spray Application is 50% of above)
Tools and Equipment:
±
2
Smooth:
325-375
Porous:
200-275
s.f./gal.
Brush -
Synthetic, Nylon or Polyester
Roller -
3/8" Nap Synthetic Fiber
Airless Spray -
.017 to .019 Tip
±2
±2
±2
±2
±5
(@ 70-77 °F, 50% R.H.)
Soap & Water
Clean Up:
Available Colors and Bases:
Gallon 5 Gallon
See back page
for complete list
ITEM # COLOR NAME
41800XX White
41891XX Light Base
41892XX Medium Base
41893XX Deep Base
41895XX Clear Base
418C155 Apache Tears
418C156 Birch Beer
418C158 Chestnut Brown
418C159 Chocolate Lab
418C160 Cubano Brown
418C161 Fawn
418C162 Grizzly Bear
418C163 Melted Chocolate
418C164 Moosehead Pin
418C165 Redwood
418C166 Rich Soil
418C167 Rusty Anchor
418C168 Southwest Sangria
418C169 Spilled Wine
418C170 Steel Rod
418D145 Gray Flannel Suit
418D146 Hollywood
418D147 Horse Trot
418D148 Joe's Moss
418D149 Lake Winnipesaukee
418D150 Lodestone
418D151 Mojave Desert
418D153 Steel Sea
418D154 Zion Forest
418L103 Bedrock
418L105 Country Club White
418L108 Ghost Plant
418L109 Granite State
Product Description:
Storm System Acrylic Stain w/ Enduradeck Technology is a low sheen finish designed for use on decks and other
exposed flat areas as well as vertical siding, fences and railings that are subjected to the rigors of drastic weather and
temperature conditions, abrasion, acid rain or snow. This high hiding stain provides maximum protection against water,
ultra violet rays and general atmospheric contamination. This stain resists cracking, peeling and blistering and can be
used on new wood, previously stained wood, properly pressure treated wood, and composite decking. This stain
contains a unique rust inhibitor to retard nail and screw head rusting.
Precautions:
All floor coatings are more slippery when the surface becomes wet or contaminated with debris. To help reduce the
potential for slipping, coated areas must be kept dry and properly cleaned of dirt, oils, food and beverage residue,
water, snow, ice and any other contaminants.
Architectural Specifications:
For decks and fences:
Unfinished wood - Best application
▪ 1 coat of 523XX Quick Dry Oil Primer + 1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series
Acceptable Application
▪ 1 coat Acrylic Stain w/ Enduradeck Technology 418 Series thinned 10-20% with water + 1 coat of Acrylic Stain w/
Enduradeck Technology 418 Series unthinned
Previously stained decks and fences
▪ 1 or 2 coats of Acrylic Stain w/ Enduradeck Technology 418 Series
For Composite Decking
1 coat Storm System Quick Dry Oil Primer 523XX + 1 coat of Acrylic Stain w/ Enduradeck Technology
418 Series.
For siding and vertical surfaces
Unfinished wood (where extractive bleeding may occur) - Best application
▪ 1 coat of Storm System™ Quick Dry Oil Primer 523XX + 1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series
Acceptable application (Where bleeding type wood is not a concern)
1 coat of Acrylic Stain w/ Enduradeck Technology 418 Series thinned with 10-20% water followed by 1 coat of Acrylic
Stain w/ Enduradeck Technology 418 Series
Previously stained wood
Application:
WARNING! If you scrape, sand or remove old paint from any surface, you may release lead dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to
control lead exposure. Carefully clean up with a wet mop or HEPA vacuum. Before you start, find out how to protect
yourself and your family by contacting the U.S. EPA/Lead Information Hotline at 1-800-424-LEAD (5323) or log on to
www.epa.gov/lead.
Surface Preparation:
Surfaces must be thoroughly clean and dry. Always test a small area before application to the entire surface. All
mildewed areas should be cleaned with Storm System All Surface Mold & Mildew Stain Remover. New pressure
treated wood should be scrubbed with Storm System All Surface Cleaner to remove all surface deposits. Rinse
thoroughly and allow to dry.
All surfaces must be free of loose wood fibers before any application.
Stir thoroughly before and during application to insure uniform appearance. Material should be intermixed by pouring
into a large container and stirring before painting large areas, to insure color uniformity. On bare wood, thin the first
coat with approximately one pint water per gallon, then apply 1 or 2 unthinned finish coats. Apply evenly with a quality
nylon or synthetic brush maintaining a wet edge. Start at the end of boards and go along surfaces to a break point to
avoid lapping. If spraying, back brush immediately. This product may also be applied by roller or pad applicator.
Clean tools and equipment immediately with warm soapy water.
New pressure treated wood must be thoroughly cleaned with Storm System All Surface Cleaner, rinsed clean and
allowed to dry completely, or allowed to weather for six months, prior to staining. Light colors may have a green cast
for a few months as the preservatives leach from the wood. Decking Stain colors vary with the different varieties of
wood. Samples should be tested on the actual wood being used before large areas of wood are stained.
Recommended Use:
Sundecks, railings and posts, fences, benches, trellis, wood walkways, open porches, wood screening, patios, garden
enclosures, outdoor furniture, siding and composite decking.
Safety Information:
Keep out of reach of children. Do not take internally. Close container after each use.
Acrylic Stain w/ Enduradeck® Technology
418 Series
4/10/2017
STORM SYSTEM™
California Paints ▪ 150 Dascomb Rd. ▪ Andover, MA ▪ 01810 ▪ www.stormsystem.com ▪ 800-225-1141
5/16/2013
Exterior
Type:
Alkyd Modified Acrylic
Specular Gloss:
8
Volume Solids:
38.8
@ 60°
%
Solids by Weight:
52.1
%
Dry Film Thickness:
1.9
mils
Vehicle:
73.0
%
Pigment:
27.0
%
Viscosity @ 77 °F:
87
KU
Maximum VOC:
100
g/liter
Flash Pt °F:
Non-combustible
Thinner:
Water
Product Specifications:
Exposure:
Exterior
(Weight Per Gallon:
10.7
Available Package Sizes:
To Handle:
6
To Recoat:
4
hrs.
hrs.
hrs.
To Touch:
1
Drying Times:
lbs. ± .5 lb)
Surface Spread Rate:
s.f./gal.
(Spray Application is 50% of above)
Tools and Equipment:
±
2
Smooth:
325-375
Porous:
200-275
s.f./gal.
Brush -
Synthetic, Nylon or Polyester
Roller -
3/8" Nap Synthetic Fiber
Airless Spray -
.017 to .019 Tip
±2
±2
±2
±2
±5
(@ 70-77 °F, 50% R.H.)
Soap & Water
Clean Up:
Available Colors and Bases:
Gallon 5 Gallon
See back page
for complete list
ITEM # COLOR NAME
418L110 Hyannis Port
418L111 Lighthouse Fog
418L112 Max Blue
418L113 Mystic Dune
418L114 Mystic Gray
418L115 Natural Clay
418L117 Peaceful Garden
418L118 Phoebe
418L119 Pigeon Feather
418L120 Plimouth Plantation
418L121 Sand Castle
418L122 Sand Dollar Taupe
418L123 Sand Dune Fence
418L124 Sea Scallop
418L125 Seacoast Gray
418L126 Seashell
418L127 Sleeping Bear Dunes
418L128 Summer Mint
418L130 Vintage Pearl
418M131 Bar Harbor
418M132 Buckskin Jacket
418M133 California Stucco
418M134 English Tweed
418M135 Irish Tweed
418M136 Laguna Beach
418M137 Naked
418M138 Sand Storm
418M139 Santa Barbara
418M140 Squirrel Tail
418M141 Sunset Beige
418M142 Susan's Glow
418M143 Tiki Tan
418M144 Wet Sand
  • Page 1 1
  • Page 2 2

Storm System 418D145-1 Instrukcja instalacji

Typ
Instrukcja instalacji

w innych językach