Haier HADG9DCS56B Instrukcja obsługi

ENGLISH

INSTALLATION AND USER’S MANUAL

SPANISH

MANUAL DE INSTALACIÓN Y USO

POLSKI

INSTRUKCJA OBSŁUGI I INSTALACJI

SERBIAN

INSTALACIJA I UPUTSTVO ZA UPOTREBU

PORTUGUÊS

MANUAL DE INSTALAÇÃO E UTILIZADOR

DEUTSCH

INSTALLATIONS- UND BEDIENUNGSANLEITUNG

БЪЛГАРСКИ

РЪКОВОДСТВО ЗА МОНТАЖ И ЕКСПЛОАТАЦИЯ

INSTALLATION AND USER’S MANUAL

CONTENT

INTRODUCTION

03

SAFETY PRECAUTION

03

ELECTRICAL INSTALLATION

05

SPECIFICATION

06

INSTALLATION (VENT OUTSIDE)

07

INSTALLATION (VENT INSIDE)

11

DESCRIPTION OF COMPONENTS

16

OPERATION

17

MAINTENANCE

19

TROBULESHOOTING

20

CONFORMITY WITH DIRECTIVES

20

ENVIRONMENTAL PROTECTION

21

2

INTRODUCTION

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required

instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction

manual carefully before installation and usage.

The cooker hood uses high quality materials, and is made with a streamlined

design. Equipped with large power electric motor and centrifugal fan, it also

provides strong suction power, low noise operation, non-stick grease filter and

easy assembly installation.

By placing the

marking on this product, we declare, on our own

responsibility, compliance to all of European safety, health and environmental

requirements stated in the legislation for this product.

SAFETY PRECAUTION

� Never let the children operate the machine.

� The cooker hood is for home use only, not suitable for barbecue, roast

shop and other commercial purpose.

� The cooker hood and its filter should be clean regularly in order to keep in

good working condition.

� Clean the cooker hood according to the instruction manual and keep the

unit from danger of burning.

� Forbid the direct baking from the gas cooker. Please keep the kitchen

room a good convection.

� Before connecting this appliance check that the power supply cord is not

damaged. A damage supply cord must be replaced by qualified service

personnel only.

� There shall be adequate ventilation of the room when the range hood is

used at the same time as appliances burning gas or other fuels;

� The air must not be discharged into a flue that is used for exhausting

fumes from appliances burning gas or other fuels;

� Regulations concerning the discharge of air have to be fulfilled.

� Children should be supervised to ensure that they do not play with the

appliance.

� Do not flambé under the range hood.

� The range hood is not intended to be installed over a hob having more

than four hob elements

3

Electrical Shock Hazard

Only plug this unit into a properly earthed outlet. If in doubt seek advice

from a suitably qualified engineer.

Failure to follow these instructions can result in death, fire, or electrical

shock.

5IFTFTIBMMCFBEFRVBUFWFOUJMBUJPOPGUIFSPPNXIFOUIFSBOHF

IPPEJTVTFEBUUIFTBNF UJNFBTBQQMJBODFTCVSOJOHHBTPSPUIFS

GVFMTOPUBQQMJDBCMFUPBQQMJBODFTUIBUPOMZEJTDIBSHFUIFBJSCBDL

JOUPUIFSPPN

UIFEFUBJMTDPODFSOJOHUIFNFUIPEBOEGSFRVFODZPGDMFBOJOH

UIFSFJTBGJSFSJTLJGDMFBOJOHJTOPUDBSSJFEPVUJOBDDPSEBODFXJUIUIF

JOTUSVDUJPOT

EPOPUGMBNFVOEFSUIFSBOHFIPPE

$"65*0/"DDFTTJCMFQBSUTNBZCFDPNFIPUXIFOVTFEXJUI

DPPLJOHBQQMJBODFT

�

4

Electrical Installation

All installation must

be carried out by a competent person or qualified

electrician. Before connecting the mains supply ensure that the mains

voltage corresponds to the voltage on the rating plate.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar

circuit breaker with a minimum opening of 3mm between the contacts.

The installer must ensure that the correct electrical connection has been

made and that it complies with the wiring diagram.

The cable must not be bent or compressed.

Regularly check the power plug and power cord for damage. If the supply

cord is damaged, it must be replaced by a special cord or assembly

available from the manufacturer or its service agent.

WARNING: This i

s a Class I appliance and MUST be earthed This

appliance is supplied with a 3 core mains cable coloured as follows:

Brown = L or Live

Blue = N or Neutral

Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

5

Standard Installation Accessories List

Spec.

Illustration Picture

Qty

Hood body 1

Lower chimney

(500mm)

1

Upper chimney

(500mm)

1

Upper chimney

bracket

1

Lower chimney

bracket

1

Cooker hood bracket 1

φ8 rawl plugs φ8×φ6

white color

9

Screw (ST4 * 8 mm)

9

Screw (ST4 * 30 mm)

6

Air outlet

1

Carbon ﬁlter 2

6

INSTALLATION (wall mounting)

If you have an outlet to the outside, your cooker hood can be connected as

below picture by means of an extraction duct (enamel, aluminum, flexible pipe

non flammabe with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75c

m above

the cooking plane for best effect.

7

INSTALLING THE HOOD

Position the hood at the desired hei

ght respecting the minimum height

above the hob.

Mark the location of the wall bracket.(Placed the holes between 700 and

800 mm above the worktop) Remove the hood and position the wall bracket

to mark the locations of the holes on the wall.

Drill the 3 holes in the wall to insert the appropriate fastening system (screw

ST4x30mm)..

Hang the hood in the notch

es of the wall

bracket.

8

INSTALLING THE HOOD

Once the hood is in place, locate the location of the 4 additional wall mount

screws as shown in the following diagram.

Remove the hood to puncture the wall and install wall plugs.

Secure the body of the hood with 4 screws of 4 mm in diameter using

dowels adapted to your wall.

If the extraction mod

e is selected, place the

exhaust air duct on the air outlet as shown.

9

INSTALLING THE HOOD

Attach the lower chimney support to the lower chimney as shown.

Use 2 screws ST4x8mm.

(Do not over tighten the screws, make sure the upper chimney can slide

easily into the lower chimney)

Insert the upper chimney into the lower chimney.

Position the bottom chi

mney in the appliance, then mark the holes on the

wall.

Remove the lower chimney, then drill holes in the wall: hole for screw

diameter Φ8 mm

Use the dowels adapted to your wall

10

INSTALLING THE HOOD

Install the lower chi

mney, then screw it to

the wall with 2 screws of diameter Φ 8 mm

Then pull the upper chimney upwards

to the desired height. Mark the

locations of the mounting holes of the

upper chimney support.

Lower the upper chimney

and then drill

holes in the wall.

Insert the dowels adapted to your wall

11

INSTALLING THE HOOD

Secure the wall bracket of the upper

chimney to the wall using the selected

dowels (8 mm screws recommended).

Reassemble the upper

chimney and fix it to the wall

bracket with 2 screws

ST4x8mm

Fasten the lower chimney to the lugs of the

kitchen hood using 2 screws ST4x8mm.

12

Standard Installation Accessories List

Spec. Illustration Picture Qty

Air Deflector

1

Bracket

1

φ8 rawl plugs

φ8×φ6 white color

2

Screws

ST4.0×30

2

Screws

ST3.5×12

2

13

INSTALLATION(AIR DEFLECTOR FOR T-SHAPE,CURVED

GLASS,FLAT GLASS MODELS):

Air deflector is mentioned as included and not optional.

1. Fix the bracket to the T-shaped plastic o

utlet with 2pcs ST3.5x12mm

screws provided as shown below:

2. Drill 2 holes on the wall to accommodate the wall plugs,then screw and

tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.

3. Attach the exhaust pipe onto the air o

utlet of the cooker hood as shown

below:

14

4. Install the chimney to the unit and fix it.

o “Please kindly be noted: T-sha

ped plastic outlet and v-flaps can not

be use d at the same time. You can use them in two ways: 1) Add v-

flap on existing o utlet; 2) Use T-shaped plastic outlet, no add v-flap.”

o “Note: The product is prov

ided with v-flap accessory. This accessory

is not mandatory for installation, operation a

nd

use of the product.”

15

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, exhaust pipe is not required and

the installation is similar to the one show in section “INSTALLATION (VENT

OUTSIDE)”.

Activated carbon filter can

be used to trap odors.

In order to install the activated carbon filter, the grease filter should be

detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in clockwise direction.

Repeat the same on the other side.

NOTE:

o Make sure the filter is securely locked. Otherwise, it would loosen and

cause dangerous.

o When activated carbon filter attached, the suction power will be

lowere

16

DESCRIPTION OF COMPONENTS

OPERATION

Timer button

1. Setting the time of the day

When hood in standby mode (motor not working), press the timer button to

enter the time setting.

Press the ‘Fan speed’ key to set the hour of the day and press the

‘Light ‘key to set the minute.

2. Setting the Timer

When the hood is in operation mode, press the timer button to

set the countdown.

Press the timer button one timer then the countdown will increase one

minute. The max countdown is 60 minutes.

Speed decrease button

The button is with indicate backlit, - for increasing the speed of the fan

or turn off the fan; when you press the button from speed 3 and the

backlit is on, the fan will be decreasing the speed from speed 3-2-1 by

press the - button, when you press the - button from speed 1, the

fan will be in standby mode. and the backlit will be turned off.

Speed plus button

The button is with indicate backlit, + for turn on the fan or increasing the

speed of the fan when you long press the button at standby mode, the

backlit will be turned on and the fan will be turned on at low speed. then

the fan will be increasing the speed from speed 1-2-3 by press the +

button

LIGHT Button

For lighting ON & OFF.

17

1. Motor symbol, will rotate when the motor is

working;

2. Time display;

3. Timer symbol, will appear when timer is setting

and counting;

4. Light symbol;

5. Motor speed;

6. Turbo speed symbol, will appear when the speed

is highest setted;

7. Alarm symbol, will appear 5 seconds when the

counting down of timer is over.

8. Cleanning alarm, appear when total working time

up to 14 hours or at the first time using after

pluging.

LCD display

18

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning

Use a soft c

loth moistened with hand-warm mildly soapy water or

household cleaning detergent. Never use metal pads, chemical, abrasive

material or stiff brush to clean the unit.

II. Monthly Cleaning for Gr

ease Filter

ESSENTIAL: Clean the filter every month can prevent any risk of fire.

The filter collects grease, smoke and dus

t…... so the filter is directly

affecting the efficiency of the cooker hood. If not cleaned, the grease

residue (potential flammable) will saturate on the filter. Clean it with

household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter

Apply SOLELY to unit that installed as a recirculation unit (not vented to

the outside). This filter traps odors and must be replaced at least once a

year

depending on how frequent the cooker hood used.

IV. Changing a light bulb

Remove the screws on the glass, take off the hood glass. Find the bulb

that requires replacement, you will find it located in the light fixture which

is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and

wiring from the hood. Important: It’s not possible to replace the

bulbs individually, it will be necessary to obtain the bulbs, bulb

holders and wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same

manners as the originals. Then reconnect the light wiring point.

19

Refit the hood glass and fasten the glass screws. Make sure the screws

are fully tightened.

TROBULESHOOTING

Fault

Cause

Solution

Light on, but

fan does not

work

The fan blade is

jammed.

Switch off the unit and repair by

qualified service personnel only.

The motor is damaged.

Both light and

fan do not

work

Halogen light bulb burn.

Replace the bulb with correct

rating.

Power cord looses.

Plug in to the power supply again.

Serious

Vibration of

the unit

The fan blade is

damaged.

Switch of the unit and repair by

qualified service personnel only.

The fan motor is not

fixed tightly.

Switch off the unit and repair by

qualified service personnel only.

The unit is not hung

properly on the bracket.

Take down the unit and check

whether the bracket is in proper

location.

Suction

performance

not good

Too long distance

between the unit and

the cooking plane

Readjust the distance to 65-75cm

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the

appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it?

It is important you to inform the Assistance Service of your product code

and its serial number (a 16 character code which begins with the number 3);

this can be found on the guarantee certificate or on the data plate located

on the appliance.

It will help to avoid wasted journeys to technicians, thereby (and most

significantly) saving the corresponding callout charges.

This appliance is marked acc

ording to the European directive

2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

WEEE contains both polluting substances (which can cause

negative consequences for the environment) and basic components (which

can be re-used). It is important to have WEEE subjected to specific

20

Strona się ładuje...

Haier HADG9DCS56B Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Haier HADG9DCS56B Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty