Intellinet iStream HD Wireless Range Extender Instrukcja obsługi

I

S

TREAM

HD

Wireless Range Extender

USER MANUAL

MODEL 525657

INT-525657-UM-0614-01

- 2 -

TABLE OF CONTENTS

INTRODUCTION ......................................................................................... 3

What Is the iStream HD Wireless Range Extender? ........................................ 3

Package Contents ..................................................................................... 3

HARDWARE OVERVIEW ............................................................................. 4

Device Status LEDs ................................................................................... 5

RJ45 Network Port .................................................................................... 6

WPS Push-Button ..................................................................................... 6

Power On / Off Switch ............................................................................... 6

Power Outlet Connector ............................................................................. 6

INSTALLATION .......................................................................................... 7

Installation Using WPS .............................................................................. 7

Manual Installation ................................................................................... 9

ADVANCED CONFIGURATION MENU ......................................................... 14

Setting Up Your Computer’s Network Adapter ............................................. 14

Accessing the Advanced Configuration Menu .............................................. 18

Advanced Configuration Menu Options ....................................................... 20

TROUBLESHOOTING ................................................................................ 27

SPECIFICATIONS .....................................................................................29

SAFETY AND REGULATORY NOTICES........................................................ 30

WARRANTY INFORMATION ...................................................................... 31

- 3 -

INTRODUCTION

What Is the iStream HD Wireless Range Extender?

Thank you for purchasing the Intellinet Network Solutions iStream HD™ Wireless

Range Extender. The iStream HD is the ideal solution for boosting your WiFi signal

and eliminating dead spots. Better wireless signal strength means you stay

connected longer and reduce your 3G/4G mobile data bill. Better wireless signal

strength also means that your wireless connection speed will be faster over a

larger area.

Enjoy a lag-free online gaming experience or watch streaming video in full HD.

Even better, the iStream HD is quick and easy to set up.

Package Contents

- iStream HD Wireless Range Extender

- Ethernet Cat5 RJ45 cable

- Quick installation guide

- 4 -

HARDWARE OVERVIEW

- 5 -

Device Status LEDs

The iStream range extender allows disabling the LEDs completely via the

configuration interface. See “Advanced Configuration Menu Options”

for details. So, if the LEDs do not light up there is no need to

panic; it may be because they have been disabled.

Signal:

This LED indicates the status of the current wireless

connection.

Steady on: Good signal reception (better than 50%).

Flashing slowly: Low signal reception.

The quality of the wireless signal is so low that the connection is subject to slow-

downs and lag. If you want to stream media or play online games, then this

represents a problem.

Flashing quickly: Poor signal reception.

The signal quality is too low. The iStream range extender cannot properly

communicate with your wireless network. If there is any communication at all, it

will be intermittent at best.

Off: The iStream isn’t connected to any wireless network.

WLAN:

When this LED flashes, it means that the wireless radio of the iStream range

extender is operating normally. The LED will flash, regardless of whether or not

the iStream range extender is connected to a network.

Power:

The Power LED is on during normal operation. When you perform a hardware

reset, the Power LED starts flashing briefly.

WPS:

If this LED is lit, it means that the iStream range extender is connected to a

wireless network via WPS (Wi-Fi Protected Setup. Read more on this below).

LAN:

This LED must light up when the iStream range extender is connected to the

network port of a Web-ready TV, Blu-ray player or gaming console.

- 6 -

RJ45 Network Port

The iStream range extender is equipped with a high-speed network port, to which

you can connect your computer for the initial setup, in case your wireless router

does not support WPS - for example Verizon FIOS

®

wireless routers. You can use

the included network cable for that purpose, but it is no problem to use any

standard Ethernet network cable that meets or exceeds the Cat5 specification. If

you are not sure about this, don’t worry. Any standard network cable purchased

from various retailers or online shops will work just fine.

WPS Push-Button

Wi-Fi Protected Setup (WPS) is a computing standard that attempts to allow easy

establishment of secure wireless home-network connections. Created by the Wi-Fi

Alliance and introduced in 2007, the goal of the protocol is to allow home users

who know little of wireless security and may be intimidated by the available

security options to set up the encryption method WPA2, as well as making it easy

to add new devices to an existing network without entering long passphrases.

So, what does this all mean for you? If your wireless router is a newer device,

there is a good chance that it is equipped with a WPS push-button, in which case

you are in luck, because adding the iStream range extender to your network will

just be a matter of a couple of minutes. If the router is a little bit older and does

not support WPS, it will take a little bit longer.

Power On / Off Switch

When it’s not in use, you can power down the iStream range extender to save

energy. Since the connection to your wireless network is re-established in less

than a minute after startup, there are no downsides to powering down the iStream

range extender when it is not in use.

Power Outlet Connector

The iStream range extender plugs directly into a power wall outlet. It supports

110V 60 Hz for U.S. and 230V 50 Hz for European power outlets. The plug type

will vary, depending on your location. The illustration below depicts the U.S.

version of the iStream adapter.

- 7 -

INSTALLATION

The iStream HD Wireless Range Extender can be installed in one of two ways. The

first way involves the aforementioned WPS, while the second (we call it the

manual method) uses a more traditional setup process. Both ways lead to the

same result, and it is only a matter of convenience as to why you would use WPS

over the manual method, provided your router supports WPS.

Installation Using WPS

If your wireless router is equipped with a WPS button (sometimes referred to as

N-connect), then you can connect the iStream HD to your network literally just by

pushing two buttons.

Plug the iStream range extender into the wall

outlet. The position of the wall outlet must be

chosen carefully: Make sure that it's close

enough to your wireless router that the

wireless signal is still relatively strong. If you

move too far away from the wireless router

and the wireless signal is already quite weak

in that location, you will not be able to

achieve good results. Use a wireless device

and check the signal strength in the location where

you plan to install the iStream HD. If the signal strength is below

50%, you should move closer to the wireless router.

Set the power switch to the “On” position, and wait for about one minute.

1

2

1

2

- 8 -

On your router, locate and press the WPS

button. The picture illustrates the location

of the WPS button on an Intellinet wireless

router.

Press the WPS button on the iStream HD for

two seconds. You have two minutes to

complete Step 4 after finishing Step 3.

Once Steps 3 and 4 are complete, the following things will happen.

 The WPS LED will flash briefly.

 The signal LED will come on.

 The WPS LED will stay on.

 After a few seconds, both the Signal and WPS LEDs

will go out.

 About 10 to 15 seconds later, both the Signal and

WPS LEDs will come back on and stay on, indicating

that the wireless connection to your network has

been successfully established.

That concludes the setup. You can now connect to the wireless network and

enjoy the improved signal strength.

3

4

5

6

5

- 9 -

Manual Installation

If you need to install the iStream HD Wireless Range Extender manually, you will

need to have the following items before you can begin.

1. You need to know the name of your wireless network (it is also referred to

as the SSID).

2. If your wireless network is protected by an encryption key, you need to

know what that password is.

Hint: It is the same password you need to enter on your laptop or tablet

when you connect to your wireless network for the first time.

3. A desktop or laptop computer running Microsoft Windows, Mac OS or Linux

that has a standard Web browser installed (Firefox, Safari, Chrome or

Internet Explorer).

Plug the iStream HD Wireless Range Extender into

the wall outlet. Make sure that the power switch is

set to the “On” position.

Note: Your computer should be shut down at this

point.

Connect the iStream HD Wireless Range Extender to your computer’s LAN

using the included network cable. Start the computer and allow it to finish

booting.

1

2

- 10 -

Launch your Web browser and direct

it to http://istreamsetup. In case this

fails, you can also enter

http://192.168.2.254.

A password window will be displayed. Key in user name “admin” and “1234”

as the password.

You will be presented with the first page of the wireless connection wizard.

The page shows all wireless networks currently in range. You need to select

the network you wish to connect to, and then click “Next.”

3

4

- 11 -

If your wireless network is secured by an encryption key, you will be

presented with the screen below. Enter the password (passphrase) for your

wireless network here.

Next, iStream will check if a connection can be made to the wireless

network.

Note: You need to type in the same password that you need in order to connect

any computer, tablet PC or smartphone to your wireless network. If the

password entered does not match, the iStream HD Wireless Range Extender

will not be able to connect. Remember that the password is case-sensitive, so

“Password” is not the same as “password.”

5

6

- 12 -

If there is a problem connecting to the wireless network, the screen below

will be shown. Click the “Back” button and re-enter the wireless password.

If all goes well, you will be presented with the following screen:

You can change the name of the wireless network from the default, which

is the same as your wireless network, to a different name. You may want to

do this so you can identify the new wireless network more easily, but doing

this is not mandatory. Click “Apply” to continue.

7

- 13 -

The iStream HD will now restart with the new settings. Once completed,

the Signal LED will light up, indicating an active wireless connection.

This concludes the manual setup procedure. You can now remove the

network cable from your computer’s LAN port and the iStream HD, and

connect to the new wireless network.

8

9

- 14 -

ADVANCED CONFIGURATION MENU

This chapter explains the advanced configuration menu of your iStream HD

Wireless Range Extender.

Setting Up Your Computer’s Network Adapter

The iStream HD operates on the IP address 192.168.2.254. For your computer to

access the advanced configuration interface, the IP address of the network adapter

in your computer has to be in the same range; e.g., 192.168.2.50. Refer to the

instructions that came with your computer for information on how to change the IP

address on the network adapter in your computer for any operating system that is

not explained in this user manual.

Windows 7:

1. Open the Network and Sharing Center.

2. Click on “Change adapter settings.”

3. Right-click your network adapter and select “Properties.”

Note: There is no need to access these functions unless you wish to upgrade the

firmware of your iStream HD range extender, change some of the advanced settings,

or disable the LEDs. A firmware upgrade is only recommended if you experience

technical difficulties with the adapter.

Additionally, accessing the advanced configuration requires advanced knowledge

about your computer system, the concept of IP addresses, and how to change the IP

settings of your network adapter.

- 15 -

4. Select “Internet Protocol Version 4” from the list and click “Properties.”

5. Enter the information as shown below, and then click “OK” to save the settings.

Windows XP:

1. Double-click the “Network Connections” icon in the control panel.

2. Right-click the connection (e.g., Local Area Connection) and select “Properties.”

3. Select “Internet Protocol (TCP/IP)” from the list and click “Properties.”

- 16 -

4. Enter the information as shown below, and then click “OK” to save the settings.

Mac OS X:

1. Open the “System Preferences” page.

2. In the Internet & Network section, click the Network icon.

3. Select either “Built-in Ethernet” or “Airport,” depending on how you connect to

the iStream adapter, then click “Configure… .”

- 17 -

4. Set the value for Configure IPv4 to “Manually” and enter 192.168.2.50 in the

IP Address field. Click “Apply Now” (not shown in screen shot) to save the

settings.

- 18 -

Accessing the Advanced Configuration Menu

Open a Web browser and go to the page http://istreamsetup. In case this link

does not work, try http://192.168.2.254.

A password request window will open up. The default user name is “admin”; the

default password is “1234.” It is recommended to change the password in the

advanced settings.

MSIE

Firefox

- 19 -

Next, you’ll be looking at the main screen of the iStream HD interface.

This page provides information about the operational status of the device. It shows

to which wireless network the iStream HD Wireless Range Extender is currently

connected, which firmware or runtime code is installed and other information.

The page also allows you to check to see if a new firmware version is available for

your iStream HD Wireless Range Extender. Simply click on the “check for new

version” link to do that. Note that your computer must be connected to the

Internet for this function to work properly.

- 20 -

Advanced Configuration Menu Options

The Quick Setup pages allow connecting the iStream HD to a wireless network.

Refer to chapter “Installation -> Manual Installation” for details.

Strona się ładuje...

Intellinet iStream HD Wireless Range Extender Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Intellinet iStream HD Wireless Range Extender Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty