Parkside PABS 12 A1 Operation and Safety Notes

Kategoria
Akumulatorowe wiertarko-wkrętarki udarowe
Typ
Operation and Safety Notes
IAN 77288
CORDLESS DRILL PABS 12 A1
AKKU-BOHRSCHRAUBER
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
CORDLESS DRILL
Operation and Safety Notes
Translation of original operation manual
WIERTARKO-WKRĘTARKA AKUMULATOROWA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
AKUMULATORSKI VRTALNI VIJAČNIK
Navodila za upravljanje in varnostna opozorila
Prevod originalnega navodila za uporabo
AKU VRTACÍ ŠROUBOVÁK
Pokyny pro obsluhu a bezpečnostní pokyny
Překlad originálního provozního návodu
AKU VŔTACÍ SKRUTKOV
Pokyny pre obsluhu a bezpečnostné pokyny
Preklad originálneho návodu na obsluhu
AKKUS FÚRÓ-CSAVAROZÓ
Kezelési és biztonsági utalások
Az originál használati utasítás fordítása
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 15
HU Kezelési és biztonsági utalások Oldal 25
SI Navodila za upravljanje in varnostna opozorila Stran 37
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 47
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 57
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 67
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funk cjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funk cióját.
Pred branjem odprite stran s slikami in se nato seznanite z vsemi funkcijami naprave.
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
A B C
D
1
2
12
14
1
8
11
9
6
7
4
3
2
10
13
5
5 GB
Table of contents
Introduction
Intended purpose ................................................................................................................................ Page 6
Equipment Components ......................................................................................................................Page 6
Items supplied ......................................................................................................................................Page 6
Technical Data ....................................................................................................................................Page 7
General safety advice for electrical power tools
1. Workplace safety ...........................................................................................................................Page 7
2. Electrical safety ............................................................................................................................... Page 8
3. Personal safety ................................................................................................................................Page 8
4. Careful handling and use of electrical power tools .....................................................................Page 9
5. Use and handling of the cordless electrical power tool ..............................................................Page 9
6. Service .............................................................................................................................................Page 9
Safety advice relating to cordless drill drivers ..................................................................................Page 10
Attention - Service lines! ......................................................................................................................Page 10
Original ancillaries / accessories .......................................................................................................Page 10
Before first use
Removing / charging / inserting rechargeable battery pack ............................................................Page 10
Checking the battery status ................................................................................................................Page 11
Changing tools .................................................................................................................................... Page 11
2 Gear Drive .......................................................................................................................................Page 11
Torque control / drill step .................................................................................................................... Page 11
Preparing the tool for use
Changing the direction of rotation / unlocking the device ...............................................................Page 11
Switching On / Off .............................................................................................................................. Page 11
Activating the lock ...............................................................................................................................Page 11
Tips and Tricks ..................................................................................................................................... Page 12
Cleaning and Maintenance ..............................................................................................Page 12
Service ...............................................................................................................................................Page 12
Warranty .........................................................................................................................................Page 12
Disposal ............................................................................................................................................Page 13
Conformity Declaration / Manufacturer ................................................................Page 14
6 GB
Introduction
Cordless drill PABS 12 A1
Introduction
We congratulate you on the purchase of
your new device. You have chosen a
high
quality product. The instructions for use
are part of the product. They contain important in-
formation concerning safety, use and disposal. Be-
fore using the product, please familiarise yourself
with all of the safety information and instructions
for use. Only use the unit as described and for the
specified applications. If you pass the product on
to anyone else, please ensure that you also pass
on all the documentation with it.
Intended purpose
This appliance is designed for drilling and screwing
into wood, plastic and metal. Use the appliance only
as described and only for the purposes indicated.
Any other uses, and modifications to the appliance,
are deemed to be improper usage and may result
in serious physical injury. The manufacturer accepts
no responsibility for damage(s) resulting from
improper usage. The appliance is not intended for
commercial use.
Equipment Components
1
Gear selector switch
2
Button for rechargeable battery LED
3
Rechargeable battery LED (status indication)
4
Direction of rotation switch/lock
5
ON / OFF switch
6
Soft-grip
7
Battery pack
8
Battery unlocking button
9
Light
10
Torque control / drill step
11
Quick-action drill chuck
12
Status LED red
13
Battery charge status indicator green
14
Fast charger
Items supplied
1 Cordless drill PABS 12 A1
1 Rechargeable battery pack PABS 12 A1-1
1 Fast charger PABS 12 A1-2
2 Bits (S2 PZ1, S2 PZ2)
1 Carry case
1 Directions for use
The following icons / symbols are used in this instruction manual:
Read instruction manual!
Keep children away from electrical
power tools!
Observe caution and safety notes! For indoor use only!
Caution – electric shock!
Danger to life!
Check that the device, mains lead
and plug are in good condition!
Explosive material!
7 GB
Introduction / General safety advice for electrical power tools
Technical Data
Cordless Drill PABS 12 A1:
Nominal voltage: 12 V
Idle-running speed: 1st gear: 0–400 min
-1
2nd gear: 0–1300 min
-1
Drill chuck
clamping range: max. 10 mm
Maximum
drill diameter:
Steel: 8 mm
Wood: 20 mm
Battery pack PABS 12 A1-1:
Type: LITHIUM-ION
Nom. voltage: 12 V
Capacity: 1300 mAh
PABS 12 A1-2 Fast Charger:
INPUT
Nominal voltage: 230 V∼ 50 Hz
Nominal power: 27 W
OUTPUT
Nominal voltage: 12.6 V
Charging current 1500 mA
Charging time: approx. 60 min
Protection class: II /
Noise / vibration data:
Measured values for noise are determined in accord-
ance with EN 60745. The A-weighted noise level
of the electrical power tool are typically:
Sound pressure level: 67.2 dB(A)
Sound power level: 78.2 dB(A)
Uncertainty K: 3 dB
Wear ear protection!
Total vibration (vector sum of three directions) is
calculated in accordance with EN 60745:
Drilling in metal: Vibration emission value
a
h,D
= 1.507 m / s
2
,
uncertainty K = 1.5 m / s
2
,
Screwing: Vibration emission value
a
h
= 0.747 m / s
2
,
uncertainty K = 1.5 m / s
2
.
The vibration level specified in
these instructions was measured in accordance with
an EN 60745 standardised measurement process
and can be used to compare equipment. The vibra-
tion emission value specified can also serve as a
preliminary assessment of the exposure.
The vibration level will change according to the ap-
plication of the electrical tool an in some cases may
exceed the value specified in these instructions. Re-
gularly using the electric tool in such a way may
make it easy to underestimate the vibration.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice for
electrical power tools
Read all the safety advice
and instructions! Failure to observe the safety
advice and instructions may result in electric shock,
fire and / or serious injury.
Keep all the safety advice and instructions
in a safe place for future reference!
The term “electrical tool” used in the safety advice
refers to electrical tools powered by mains electrici-
ty (by means of a mains lead) and electrical tools
powered by rechargeable batteries (without a
mains lead).
1. Workplace safety
a) Keep your working area clean and
well lit. Untidy or poorly lit working areas
can lead to accidents.
8 GB
b) Do not work with the device
in potentially explosive envi-
ronments in which there are-
inflammable liquids, gases or dusts.
Electrical power tools create sparks, which can
ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
2. Electrical safety
a)
The mains plug on the device must match
the mains socket. The plug must not
be modified in any way. Do not use
an adapter plug with devices fitted
with a protective earth. Unmodified
plugs and matching sockets reduce the risk of
electric shock.
b) Avoid touching earthed surfaces such
as pipes, radiators, ovens and refrig-
erators with any part of your body.
There is an increased risk of electric shock if
your body is earthed
.
c) Keep the device away from rain or
moisture. Water entering an electrical device
increases the risk of electric shock.
d)
Do not use the mains lead for
any purpose for which it was
not intended, e.g. to carry the
device, to hang up the device or to pull
the mains plug out of the mains socket.
Keep the mains lead away from heat,
oil, sharp edges or moving parts of the
device. Damaged or tangled mains leads
increase the risk of electric shock.
e) When working outdoors with an
electrical power tool always use ex-
tension cables that are also approved
for use outdoors. The use of an extension
cable suitable for outdoor use reduces the risk
of electric shock.
f) Use a residual current device (RCD)
for protection if operating the electri-
cal power tool in a moist environment
is unavoidable. The use of an RCD reduces
the risk of electric shock.
3. Personal safety
a) Remain alert at all times, watch what
you are doing and always proceed
with caution. Do not use the device if
you are tired or under the influence of
drugs, alcohol or medication. One mo
ment
of carelessness when using the device can lead
to serious injury.
b)
Wear personal protective
equipment and always wear
safety glasses. The wearing of
personal protective equipment such as dust
masks, non-slip safety shoes, safety helmets or
ear protectors, appropriate to the type of elec-
trical power tool used and work undertaken,
reduces the risk of injury.
c) Avoid unintentional operation of the
device. Check that the electrical power
tool is switched off before you connect
it to the mains, pick it up or carry it.
Accidents can happen if you carry the device
with your finger on the ON / OFF switch or with
the device switched on.
d) Remove any setting tools or spanners
before you switch the device on. A tool
or spanner left attached to a rotating part of a
device can lead to injury.
e) Avoid placing your body in an unnat-
ural position. Keep proper footing
and balance at all times. By doing this
you will be in a better position to control the
device in unforeseen circumstances.
f) Wear suitable clothing. Do not wear
loose clothing or jewellery. Keep your
hair, clothing and gloves clear of mov-
ing parts. Loose clothing, jewellery or long
hair can become trapped in moving parts.
g) If vacuum dust extraction and collection
devices are fitted do not forget to
check
that they are properly connected and
correctly used. The use of these devices
reduces the hazard presented by dust.
General safety advice for electrical power tools
General safety advice for electrical power tools
9 GB
4. Careful handling and use
of electrical power tools
a) Do not overload the device. Always
use an electrical power tool that is
intended for the task you are under-
taking. By using the right electrical power
tool for the job you will work more safely and
achieve a better result.
b) Do not use an electrical power tool if
its switch is defective. An electrical power
tool that can no longer be switched on and off
is dangerous and must be repaired.
c) Pull the mains plug out of the socket
and / or remove the rechargeable bat-
tery before you make any adjustments
to the device, change accessories or
when the device is put away. This pre-
caution is intended to prevent the device from
unintentionally starting.
d) When not in use always ensure that
electrical power tools are kept out of
reach of children. Do not let anyone use
the device if he or she is not familiar
with it or has not read the instructions
and advice. Electrical power tools are dan-
gerous when they are used by inexperienced
people.
e) Look after the device carefully. Check
that moving parts are working prop-
erly and move freely. Check for any
parts that are broken or damaged
enough to detrimentally affect the
functioning of the device. Have dam-
aged parts repaired before you use
the device. Many accidents have their origins
in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp.
Carefully maintained cutting tools with sharp
cutting edges are less likely to jam and are
easier to control.
g) Use the electrical power tool, accesso-
ries, inserted tools etc. in accordance
with these instructions and advice, and
the stipulations drawn up for this par-
ticular type of device. In doing this, take
into account the working conditions
and the task in hand. The use of electrical
power tools for purposes other than those in-
tended can lead to dangerous situations.
5. Use and handling of the cord-
less electrical power tool
a) Charge a rechargeable battery unit
using only the charger recommended
by the manufacturer. Chargers are often
designed for a particular type of rechargeable
battery unit. There is the danger of fire if other
types of rechargeable battery units are used.
b) Only the rechargeable battery units
supplied are to be used with an elec-
trical power tool. The use of other recharge-
able battery units may lead to the danger of
injury or fire.
c) When they are not being used, store
rechargeable battery units away from
paperclips, coins, keys. nails, screws
or other small metal objects that could
cause the contacts to be bridged. Short-
circuiting the contacts of a rechargeable battery
unit may result in heat damage or fire.
d) Fluids may leak out of rechargeable
battery units if they are misused. If
this happens, avoid contact with the
fluid. If contact occurs, flush the affect-
ed area with water. Seek additional
medical help if any of the fluid gets
into your eyes. Escaping battery fluid may
cause skin irritation or burns.
CAUTION! DANGER OF EX-
PLOSION! The batteries must
never be recharged!
6. Service
a) Have your device repaired at the ser-
vice centre or by qualified specialist
personnel using original manufacturer
parts only. This will ensure that your device
remains safe to use.
General safety advice for electrical power tools
General safety advice for electrical power tools
10 GB
Safety advice relating
to cordless drill drivers
The inserted tool may
strike concealed electricity cables,
therefore when working you must
hold the electrical power tool by the
insulated handle areas only. Contact
with a live wire means that the metal parts of
the electrical power tools may become live and
this can result in an electric shock.
Securely support the workpiece.
A workpiece held in a clamp or vice is kept more
securely in place than one held by your hand.
POISONOUS DUSTS!
Harmful / noxious dusts generated from your
work represent a risk to the health of the person
operating the device and to anyone near the
work area.
Wear safety glasses and a dust
mask!
Do not drill any material containing
asbestos. Asbestos is a known carcinogen.
Hold the electrical power tool firmly.
High reaction torques may occur momentarily
during tightening or loosening of screws.
If the inserted tool jams, switch off the
electrical power tool immediately. Be
prepared for high reaction torques as they may
cause kickback. The inserted tool may jam if
the electrical power tool is overloaded or is
held at an angle to the workpiece.
Before you carry out any tasks on the
device, transport or store it, make sure
that the direction of rotation switch is
in the middle position (lock). To prevent
the device from starting up unintentionally.
Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsi-
ble for their safety. Children must never be
allowed to play with the device.
Attention - Service lines!
Take steps to ensure that
you do not hit upon any service lines
(electricity, gas, water) when working
with electrical appliances. Check, if need be
with a service line detector, before you start to cut
or bore into a surface.
Original ancillaries /
accessories
Use only the ancillaries and accessories
that are detailed in the operating
instructions. The use of ancillaries and ac-
cessories other than those recommended in the
operating instructions could lead to an in-
creased risk of personal injury for you.
Before first use
Removing / charging / inserting
rechargeable battery pack
Note: The battery is supplied partially charged.
Charge the rechargeable battery in the charging
station for at least one hour before first use. By doing
this the battery will operate at its highest capacity.
You can charge the Li-Ion battery at any time with-
out risk of shortening battery life. Interrupting the
charging process does not damage the battery.
1. In order to remove the rechargeable battery pack
7
, press the release buttons
8
and take the
rechargeable battery pack
7
out of the device.
2. Insert the rechargeable battery pack
7
into the
quick-charger
14
.
3. Insert the mains plug into the mains socket.
The indicator LED
12
illuminates red.
4. The green charge indicator LED
13
shows you
that the charging process is complete and the
battery pack
7
is ready for use.
5. Insert the rechargeable battery pack
7
into
the device.
Before first use / Preparing the tool for use
General safety advice for electrical power tools / Before first use
11 GB
Checking the battery status
To check the battery status, press the button for
the rechargeable battery LED
2
(refer to main
diagram). The status or the remaining power
will be displayed in the rechargeable battery
LED
3
as follows:
RED / ORANGE / GREEN = maximum charge /
performance
RED / ORANGE = medium charge / performance
RED = low charge – recharge battery
Changing tools
Your cordless drill / screwdriver has a fully automat-
ic spindle lock
.
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck
11
can
be opened simply by turning it
.
After you have inserted the required bit and fixed it
in place by turning the chuck
, you can immedi-
ately continue working. The spindle lock releases
itself automatically when the motor is started (by
operation of the ON / OFF switch
5
).
2 Gear Drive
Note: Move the gear selector switch
1
only after
the device has come to a standstill.
In the first gear (Gear selector switch
1
in Position: 1)
you achieve a speed of up to approx. 400 rpm and a
high torque. This setting is suitable for all screwing tasks.
In the second gear (Gear selector switch
1
in Position: 2)
It achieves a speed of up to approx. 1300 rpm, for
the carrying out of drilling tasks.
Torque control / drill step
You can use the torque control / drill step
10
to
adjust the torque. When the value of the torque
setting is reached, the clutch disengages the drive
connection to the chuck.
Select a low setting for small screws, soft work
material.
Select a high setting for large screws, hard
work materials and for the extraction of screws.
For drilling work, select the drill setting by putting
the torque control / drill setting into the
position.
For drilling tasks, also push the gear selector
switch
1
to the front (Position: 2).
Preparing the tool for use
Changing the direction of
rotation / unlocking the device
Unlock the device and change the direction of rota-
tion by pressing the rotational direction switch
4
to the right or to the left.
Switching ON / OFF
Switching on:
To start the appliance squeeze on the ON /
OFF switch
5
and then keep it pressed down.
The light
9
comes on with a slightly or fully
pressed ON / OFF switch
5
and illuminates
the working area in poor lighting conditions.
Switching off:
To stop the appliance, release the ON / OFF
switch
5
.
Changing the rotational speed:
The ON / OFF switch
5
has a variable speed
control. Light pressure on the ON / OFF switch
5
causes the device to operate at a low speed. In-
creasing the pressure increases the speed.
Activating the lock
Press the rotational direction switch
4
into the
middle position. The ON / OFF switch
5
is
now blocked.
Before first use / Preparing the tool for use
12 GB
Tips and Tricks
When screwing into wood, metal and
other materials:
Screw bits are designated with their dimensions
and their shape. If you are unsure, always try
the particular screw bit out to see whether it sits
in the screw head without any free play.
Before you use the appliance, check to see
that the screw or drill bit is properly fitted, i.e.
located centrally in the chuck.
Torque:
Smaller screws and bits in particular can be
easily damaged if you adjust the appliance
with too high a torque and/or rotation speed.
Hard screw bed:
Particularly high torques can occur, for example
with metal screws tightened by socket tool bits.
Select a lower rotation speed.
Soft screw bed:
You should also select a low speed in order not
to damage the wood workpiece surface through
contact with the metal screw head. Use a coun-
tersinker.
When drilling into wood, metal and other
materials:
With small diameter drill bits use a high drill
speed. For large diameter drill bits, use a low
drill speed.
For hard materials, select a low drill speed.
For soft materials, select a high drill speed.
Secure or fix down the workpiece (if possible)
in a clamp or vice.
Mark the intended position of the hole with a
centre punch or a nail and select a low drill speed
for drilling.
Take the rotating drill bit out of the hole frequently
so that swarf or drill dust can be re-moved and
the hole and tool is ventilated.
Drilling in metal:
Use a metal drill bit (HSS). For the best results,
you should cool the bit with oil. Metal drill bits
can also be used to drill into plastic.
Drilling in wood:
Normally you should use a wood drill with a
centring point. You can screw small screws into
soft wood without the need for pre-drilling.
Cleaning and Maintenance
Pull the mains plug out of the mains socket and re-
move the rechargeable battery pack
7
every time
before you clean or maintain the device.
The Cordless Drill / Screwdriver is maintenance-free.
Always keep the device clean, dry and free of
oil or grease.
Clean the device immediately after you have
finished using it.
Do not allow any liquids to enter the device.
Use a cloth to clean the housing.
Never use petrol, solvents or cleaning agents
that might attack plastic.
Service
Have your device repaired
at the service centre or by qualified
specialist personnel using original
manufacturer parts only. This will ensure
that your device remains safe to use.
If the plug or lead needs
to be replaced, always have the
replacement carried out by the manu-
facturer or its service centre. This will
ensure that your device remains safe to use.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
Warranty / Disposal
Preparing the tool for use / Cleaning and Maintenance / Service / Warranty
13 GB
The warranty covers only claims for material and
maufacturing defects, but not for transport damage,
for wearing parts or for damage to fragile compo-
nents, e.g. buttons or batteries. This product is for pri-
vate use only and is not intended for commercial use.
The warranty is void in the case of abusive and im-
proper handling, use of force and internal tamper-
ing not carried out by our authorized service branch.
Your statutory rights are not restricted in any way
by this warranty.
The warranty period will not be extended by repairs
made unter warranty. This applies also to replaced
and repaired parts. Any damage and defects extant
on purchase must be reported immediately after
unpacking the appliance, at the latest, two days after
the purchase date. Repairs made after the expiration
of the warranty period are subject to payment.
GB
Service Great Britain
Tel.: 0871 5000 720
(0,10 GBP/Min.)
IAN 77288
Disposal
The packaging comprises exclusively en-
vironmentally-friendly material. Dispose
of it in your local recycling containers.
Do not dispose of electrical
appliances with your domestic
waste!
According to the European Directive 2002 / 96 / EC,
concerning used electrical and electronic appliances
and its implementation in national law, superannu-
ated electrical appliances must be collected and
disposed of via an environmentally suitable recy-
cling facility.
Do not dispose of rechargeable
batteries with your household
refuse!
Defective or worn out rechargeable batteries must
be recycled according to Directive 2006 / 66 / EC.
Dispose of batteries and appliances over the existing
collection facilities.
Your local communal or municipal authorities can
provide information on how to dispose of the worn
out appliance.
Warranty / Disposal
Preparing the tool for use / Cleaning and Maintenance / Service / Warranty
14 GB
Conformity Declaration / Manufacturer
Spis zawartości
Conformity Declaration /
Manufacturer
We, Kompernaß GmbH, the person responsible for
documents: Mr Semi Uguzlu, Burgstr. 21, D-44867
Bochum, Germany, hereby declare that this product
complies with the following standards, normative
documents and EU directives:
Machinery Directive
(2006 / 42 / EC)
EU Low Voltage Directive
(2006 / 95 / EC)
Electromagnetic Compatibility
(2004 / 108 / EC)
Applicable harmonized standards
EN 60745-1/A11:2010
EN 60745-2-1:2010
EN 60745-2-2:2010
EN 55014-1/A2:2011
EN 55014-2/A2:2008
EN 60335-2-29/A2:2010
EN 60335-1/A15:2011
EN 62233:2008
EN 61000-3-2/A2:2009
EN 61000-3-3:2008
Type / Appliance Designation:
Cordless drill PABS 12 A1
Date of manufacture (DOM): 08–2012
Serial number: IAN 77288
Bochum, 31.08.2012
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical modifica-
tions in the course of further development.
15 PL
Conformity Declaration / Manufacturer
Spis zawartości
Wstęp
Przeznaczenie ..................................................................................................................................Strona 16
Wyposażenie ...................................................................................................................................Strona 16
Zawartość zestawu ..........................................................................................................................Strona 16
Dane techniczne ..............................................................................................................................Strona 17
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi ............... Strona 17
1. Bezpieczeństwo miejsca pracy ..................................................................................................Strona 18
2. Bezpieczeństwo elektryczne .......................................................................................................Strona 18
3. Bezpieczeństwo osób .................................................................................................................Strona 18
4. Staranne obchodzenie się i użytkowanie narzędzi elektrycznych ..........................................Strona 19
5. Używanie i obchodzenie się z narzędziem akumulatorowym .................................................Strona 19
6. Serwis ...........................................................................................................................................Strona 20
Wskazówki dotyczące bezpieczeństwa dla wiertarkowkrętarek akumulatorowych .................Strona 20
Uwaga na przewody! ..................................................................................................................... Strona 20
Oryginalne akcesoria / dodatkowy sprzęt .....................................................................................Strona 21
Przed uruchomieniem
Pakiet akumulatorowy wyjmowanie / ładowanie / zakładanie ....................................................Strona 21
Sprawdzenie stanu naładowania akumulatora .............................................................................Strona 21
Zmiana narzędzi ..............................................................................................................................Strona 21
Przekładania 2-biegowa .................................................................................................................Strona 21
Wybór momentu obrotowego / stopnia wiertarskiego .................................................................Strona 22
Uruchomienie
Przełączanie kierunku obrotów / odblokowanie urządzenia .......................................................Strona 22
Włączenie / Wyłączenie .................................................................................................................Strona 22
Aktywowanie blokady .....................................................................................................................Strona 22
Wskazówki i porady .......................................................................................................................Strona 22
Konserwacja i czyszczenie............................................................................................Strona 23
Serwis .............................................................................................................................................Strona 23
Gwarancja ..................................................................................................................................Strona 23
Usuwanie ..................................................................................................................................... Strona 24
Deklaracja zgodności / Producent ..........................................................................Strona 24
16 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
Wiertarko-wkrętarka
akumulatorowa PABS 12 A1
Q
Wstęp
Gratulujemy zakupu nowego urządzenia.
Tym samym zdecydowali się Państwo na
zakup produktu wysokiej jakości. Instrukcja
obsługi jest częścią tego produktu. Zawiera ona
ważne wskazówki dotyczące bezpieczeństwa,
użytkowania iutylizacji. Przed pierwszym użyciem
produktu należy zapoznać się ze wszystkimi wska-
zówkami dotyczącymi obsługi ibezpieczeństwa.
Używać produktu wyłącznie zgodnie zjego poniżej
opisanym przeznaczeniem. Wprzypadku przeka-
zania produktu innej osobie należy dołączyć do
niego całą jego dokumentację.
Q
Przeznaczenie
To urządzenie jest przeznaczone do wiercenia i
wkręcania w drewno, plastik i metal. Urządzenie
należy stosować zgodnie z opisem i w podanych
zakresach użytkowania. Jakiekolwiek inne użycie lub
zmiany urządzenia uważane są za niezgodne z
przeznaczeniem i kryją w sobie poważne niebez-
pieczeństwo wypadku. Producent nie bierze na
siebie żadnej odpowiedzialności w przypadku po-
wstania szkody, wynikającej z użytkowania urzą
dzenia
w sposób całkowicie niezgodny z przeznaczeniem.
Urządzenie nie nadaje się do celów komercyjnych.
Q
Wyposażenie
1
Przełącznik wyboru biegu
2
Przycisk lampki LED akumulatora
3
Lampka LED akumulatora (wskazanie stanu
naładowania)
4
Przełącznik kierunku obrotów / blokada
5
Przełącznik (WŁ. / W.)
6
Miękki uchwyt
7
Pakiet akumulatorowy
8
Przycisk odblokowujący akumulatora
9
Lampka oświetleniowa
10
Ustawianie momentu obrotowego /
stopnia wiertarskiego
11
Uchwyt wiertarski do szybkiego mocowania
12
Lampka kontrolna LED czerwona
13
Lampka sygnalizacyjna stanu
naładowania, zielona
14
Ładowarka
Q
Zawartość zestawu
1 W
iertarko-wkrętarka akumulatorowa PABS 12 A1
1 Pakiet akumulatorowy PABS 12 A1-1
1 Ładowarka PABS 12 A1-2
2 Końcówki (S2 PZ1, S2 PZ2)
1 Walizka do przenoszenia
1 Instrukcja obsługi
W niniejszej instrukcji obsługi urządzenia zastosowano następujące piktogramy:
Przeczytaj instrukcję obsługi!
Dzieci trzymać z daleka od narzę-
dzia elektrycznego!
Przestrzegaj wskazówek
ostrzegawczych i bezpieczeństwa!
Tylko do użytku w pomieszczeniach
wewnętrznych!
Ostrzeżenie przed porażeniem
prądem elektrycznym!
Zagrożenie dla życia!
Zwracać uwagę na nienaruszony
stan urządzenia, kabla sieciowego
oraz wtyczki sieciowej!
Niebezpieczeństwo wybuchu!
17 PL
Wstęp / Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Wstęp
Q
Dane techniczne
Wiertarko-wkrętarka akumulatorowa
PABS 12 A1:
Napięcie nominalne: 12 V
Liczba obrotów na
biegu jałowym: 1. bieg: 0–400 min
-1
2. bieg: 0–1300 min
-1
Zakres mocowania
uchwytu wiertarskiego: maks. 10 mm
Maksymalna średnica
wiertła:
do stali: 8 mm
do drewna: 20 mm
Pakiet akumulatorowy PABS 12 A1-1:
Typ: LITOWOJONOWY
Napięcie znamionowe: 12 V
Pojemność: 1300 mAh
PABS 12 A1-2
Ładowarka:
WEJŚCIE / Input:
Napięcie nominalne: 230 V
~
50 Hz
Moc znamionowa: 27 W
WYJŚCIE / Output:
Napięcie nominalne: 12,6 V
Prąd ładowania: 1500 mA
Czas ładowania: ok. 60 min
Klasa ochrony: II /
Informacja dotycząca hałasu / drgań:
Wartość pomiarowa hałasu wyznaczona zgodnie
z EN 60745. Poziom hałasu elektronarzędzia wg
oceny A wynosi typowo:
Poziom ciśnienia hałasu: 67,2 dB(A)
Pozom mocy hałasu: 78,2 dB(A)
Niepewność pomiaru K: 3 dB
Zakładać ochronniki słuchu!
Sumaryczne wartości drgań (suma wektorów z trzech
kierunków) wyznaczone zgodnie z EN 60745:
Wiercenie w metalu: Wartość emisji drgań
a
h,D
= 1,507 m / s
2
,
Niepewność K = 1,5 m / s
2
,
Wkręcanie śrub: Wartość emisji drgań
a
h
= 0,747 m / s
2
,
Niepewność K = 1,5 m / s
2
.
Podany w niniejszych in-
strukcjach poziom drgań wyznaczony został za
pomocą metody pomiarowej określonej w normie
EN 60745 i może zostać użyty do porównania
urządzeń. Podany poziom emisji drgań może być
wykorzystywany również do wstępnego oszaco-
wania przerw w działaniu.
Poziom drgań będzie się różnił w zależności od
zastosowania elektronarzędzia i w niektórych
przypadkach może przekroczyć wartość podaną
w niniejszej instrukcji. Obciążenie drganiami może
wydawać się mniejsze niż w rzeczywistości, jeśli
elektronarzędzie będzie regularnie używane ten
sposób.
Wskazówka: Celem dokładnego oszacowania
obciążenia wibracjami w okresie określonego okresu
czasu pracy należy uwzględnić również te okresy,
w których urządzenie jest wyłączone lub wpraw
dzie
jest włączone, ale w rzeczywistości nie pracuje.
Może to przyczynić się do znacznej redukcji ob-
ciążenia wibracjami w całym okresie czasu pracy.
Ogólne wskazówki
bezpieczeństwa dla
elektronarzędzi
Przeczytaj wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje! Zaniedbania w przestrzeganiu
wskazówek dotyczących bezpieczeństwa oraz w
przestrzeganiu instrukcji mogą spowodować pora-
żenie prądem elektrycznym, pożar i / lub ciężkie
obrażenia ciała.
Przechowuj na przyszłość wszystkie
wskazówki dotyczące bezpieczeństwa
oraz instrukcje!
18 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Używany we wskazówkach dotyczących bezpie-
czeństwa termin „narzędzie elektryczne“ odnosi s
do narzędzi elektrycznych zasilanych z sieci (z ka-
blem sieciowym) oraz do narzędzi elektrycznych
zasilanych z akumulatorów (bez kabla sieciowego).
1.
Bezpieczeństwo miejsca pracy
a) Utrzymywać stanowisko pracy w czy-
stości i dobrze oświetlone. Nieporządek
i nieoświetlone obszary robocze mogą prowa-
dzić do wypadków.
b)
Nie pracuj przy użyciu urzą-
dzenia w otoczeniu zagrożo-
nym eksplozją, w którym
znajdują się palne ciecze, gazy lub
pyły. Urządzenia elektryczne wytwarzają
iskry, które mogą zapalić pył lub pary.
c)
Podczas użytkowania urzą-
dzenia elektrycznego trzymaj
dzieci i inne osoby z daleka
od urządzenia. Przy odchyleniu możesz
stracić kontrolę nad urządzeniem.
2.
Bezpieczeństwo elektryczne
a) Wtyk sieciowy urządzenia musi
pasować do wtykowego gniazdka
sieciowego. W żaden sposób nie wol-
no zmieniać wtyku sieciowego urzą-
dzenia. Nie używaj żadnych wtyków
adapterowych razem z urządzeniami
wyposażonymi w uziemienie ochron
ne.
Niezmienione wtyki sieciowe i pasujące wtykowe
gniazdka sieciowe zmniejszają ryzyko poraże-
nia prądem elektrycznym.
b) Unikaj kontaktu fizycznego z powier-
zchniami uziemionymi takimi jak
powierzchnie rur, grzejników, kuchni
elektrycznych i lodówek. Istnieje podwyż-
szone niebezpieczeństwo porażenia prądem
elektrycznym, gdy twoje ciało jest uziemione.
c) Trzymaj urządzenie z daleka od desz-
czu i wilgoci. Wniknięcie wody do urządzenia
elektrycznego zwiększa ryzyko porażenia prą-
dem elektrycznym.
d)
Nie używaj kabla sieciowego w
sposób sprzeczny z jego prze-
znaczeniem, tj. do noszenia
urządzenia, zawieszania urzą dzenie
lub do wyciągania wtyku sieciowego
z wtykowego gniazdka sieciowego.
Trzymaj kabel z daleka od gorąca,
oleju, ostrych krawędzi lub porusza-
jących się części urządzeń. Uszkodzone
lub poplątane kable zwiększają ryzyko pora-
żenia prądem elektrycznym.
e)
Gdy pracujesz z urządzeniem elektrycz-
nym na dworze używaj wyłącznie
przedłużaczy, które są dopuszczone
również do pracy na dworze. Użycie
przedłużacza przystosowanego do stosowania
na dworze zmniejsza ryzyko porażenia prądem
elektrycznym.
f) Jeśli praca elektronarzędzia w otocze-
niu wilgotnym jest nie do uniknięcia,
należy zastosować wyłącznik prądu
uszkodzeniowego. Zastosowanie wyłącz-
nika prądu uszkodzeniowego zapobiega nie-
bezpieczeństwu porażenia prądem elektrycz
nym.
3. Bezpieczeństwo osób
a) Bądź stale uważny, zwracaj uwagę
na to co robisz i postępuj rozsądnie w
trakcie pracy z narzędziem elektrycz-
nym. Nie używaj narzędzia, gdy jesteś
zmęczony lub znajdujesz się pod
wpływem narkotyków, alkoholu lub
lekarstw. Chwila nieuwagi przy użytkowaniu
urządzenia może prowadzić do poważnych
obrażeń ciała.
b)
Noś osobiste wyposażenie
ochronne i zawsze okulary
ochronne. Noszenie osobistego
wyposażenia ochronnego takiego jak maska
przeciwpyłowa, buty antypoślizgowe, kask
ochronny lub ochrona słuchu stosownie do
sposobu użytkowania narzędzia elektrycznego
zmniejsza ryzyko obrażeń ciała.
c) Unikaj niezamierzonego uruchomienia.
Upewnij się, że narzędzie elektryczne
jest wyłączone zanim podłączysz je
19 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
do zasilania prądowego, uchwycisz je
lub będziesz je przenosił. Jeżeli podczas
przenoszenia urządzenia będziesz trzymał
palec na przełączniku WŁĄCZ. / WYŁĄCZ.
lub jeżeli urządzenie jest włączone, to może
to prowadzić do nieszczęśliwych wypadków.
d) Usuń narzędzia do nastawiania urzą-
dzenia lub klucze płaskie zanim włą-
czysz urządzenie. Narzędzie lub klucz,
który znajduje się w obracającej się części
urządzenia może prowadzić do obrażeń ciała.
e) Unikaj nienormalnej postawy ciała.
Zadbaj o pewne stanowisko i w każdej
chwili utrzymuj równowagę. Dzięki temu
będziesz mógł lepiej kontrolować urządzenie,
zwłaszcza w nieoczekiwanych sytuacjach.
f) Noś odpowiednią odzież. Nie noś ob-
szernej odzieży ani biżuterii. Trzymaj
włosy, odzież i rękawice z daleka od
poruszających się części. Luźna odzież,
biżuteria lub długie włosy mogą zostać uchwy-
cone przez poruszające się części.
g) Jeżeli zostaną zamontowane urzą-
dzenia do odsysania i wychwytywania
pyłu, to upewnij się, że są one podłą-
czone i że będą prawidłowo używane.
Używanie tych urządzeń zmniejsza zagrożenie
wywoływane pyłem.
4.
Staranne obchodzenie się
i użytkowanie narzędzi
elektrycznych
a) Nie przeciążaj urządzenia. Używaj do
swojej pracy przeznaczonego do niej
narzędzia elektrycznego. Za pomocą odpo
-
wiedniego narzędzia elektrycznego pracujesz
lepiej i bezpieczniej w danym zakresie robót.
b) Nie używaj żadnego narzędzia elek-
trycznego, którego przełącznik jest
uszkodzony. Narzędzie elektryczne, które
nie daje się już więcej włączyć lub wyłączyć,
jest niebezpieczne i musi zostać naprawione.
c) Proszę usunąć wtyczkę z gniazdka
oraz / lub usunąć akumulator, zanim
rozpoczną państwo ustawienie urzą-
dzenia, wymianę części lub w przy-
padku odłożenia urządzenia. Niniejsze
przedsięwzięcie zapobiega niekontrolowanemu
rozruchowi niniejszego narzędzia elektrycznego.
d) Przechowuj nieużywane narzędzia
elektryczne poza zasięgiem dzieci. Nie
pozwól na użytkowanie urządzenia
osobom, które nie są z nim obznajo-
mione lub nie przeczytały niniejszych
instrukcji. Narzędzia elektryczne są niebez-
pieczne, gdy są używane przez osoby niedo-
świadczone.
e) Pielęgnuj starannie urządzenie.
Sprawdź, czy ruchome części urzą-
dzenia funkcjonują nienagannie i nie
zakleszczają się, czy części urządzenia
nie są złamane lub uszkodzone w ta-
kim stopniu, że funkcjonowanie urzą-
dzenia jest uszczuplone. Zleć naprawę
uszkodzonych części przed użyciem
urządzenia. Przyczyną wielu wypadków są
źle konserwowane narzędzia elektryczne.
f) Utrzymuj narzędzia tnące w stanie
ostrym i czystym. Starannie pielęgnowane
narzędzia tnące o ostrych krawędziach tnących
mniej zakleszczają się i dają się łatwiej prowa
dzić.
g) Używaj narzędzia elektrycznego,
osprzętu, narzędzi wymiennych itp.
odpowiednio do niniejszych instrukcji
i w taki sposób, jaki jest zalecany dla
tego specjalnego typu urządzenia.
Uwzględniaj przy tym warunki robo-
cze i wykonywane czynności. Użycie
narzędzi elektrycznych do innych zastosowań
niż to przewidziano może prowadzić do nie-
bezpiecznych sytuacji.
5. Używanie i obchodzenie się z
narzędziem akumulatorowym
a) Ładuj akumulatory wyłącznie w tych
ładowarkach, które są zalecane przez
producenta. Dla ładowarki, która nadaje się
do określonego rodzaju akumulatorów istnieje
zagrożenie pożarowe, gdy będzie ona używana
z innymi akumulatorami.
b) W narzędziach elektrycznych stosuj
wyłącznie przewidziane dla nich aku-
20 PL
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi / Przed uruchomieniem
Ogólne wskazówki bezpieczeństwa dla elektronarzędzi
mulatory. Używanie innych akumulatorów
może prowadzić do obrażeń ciała i zagrożenia
pożarowego.
c) Nieużywane akumulatory trzymaj z
daleka od spinaczy biurowych, monet,
kluczy, gwoździ śrub oraz innych ma-
łych przedmiotów metalowych, które
mogłyby spowodować zmostkowanie
styków akumulatora. Skutkiem zawarcia
styków akumulatora mogą być oparzenia lub
pożar.
d)
W przypadku nieprawidłowego za-
stosowania akumulatora może z niego
wyciec ciecz. Unikaj kontaktu z nią.
W razie przypadkowego kontaktu
spłucz ją wodą. Jeżeli ta ciecz dostanie
się do oka, to dodatkowo skorzystaj
z pomocy lekarskiej. Wyciekła ciecz aku-
mulatorowa może prowadzić do podrażnień
skóry lub oparzeń.
OSTROŻNIE! ZAGROŻENIE
EKSPLOZJĄ! Nie należy ładować
baterii nie przystosowanych do
powtόrnego ładowania.
6.
Serwis
a) Urządzenie oddawać do naprawy tyl-
ko wykwalifikowanemu personelowi
fachowemu i tylko z użyciem oryginal-
nych części zamiennych. To sposób na
zapewnienie bezpieczeństwa urządzenia.
Wskazówki dotyczące
bezpieczeństwa dla
wiertarkowkrętarek
akumulatorowych
Chwytaj narzędzie
elektryczne wyłącznie za izolowane
powierzchnie chwytne, gdy wykonu-
jesz roboty, w trakcie których założone
narzędzie może natrafić na ukryte
przewody prądowe. Styczność z przewo-
dem pod napięciem spowoduje, że części me-
talowe narzędzia elektrycznego również znajdą
się pod napięciem, co prowadzi do porażenia
prądem elektrycznym.
Zabezpiecz przedmiot obrabiany.
Przedmiot obrabiany przytrzymywany za po-
mocą urządzenia mocującego lub imadła jest
trzymany pewniej niż ręką.
TRUJĄCE PYŁY!
Powstające wskutek obróbki szkodliwe / trujące
pyły stanowią zagrożenie dla zdrowia dla osoby
obsługującej urządzenie lub osób znajdujących
się w pobliżu.
Noś okulary ochronne i maskę prze-
ciwpyłową!
Nie obrabiaj materiału zawierającego
azbest. Azbest jest uznawany za rakotwórczy.
Trzymaj mocno narzędzie elektryczne.
Przy dokręcaniu lub luzowaniu śrub mogą krót-
kotrwale wystąpić duże momenty reakcji.
Wyłączaj natychmiast narzędzie elek-
tryczne, gdy założone do niego na-
rzędzie zablokuje się. Bądź przygotowany
na duże momenty reakcji, które powodują
odrzut. Założone narzędzie zablokuje się, gdy
narzędzie elektryczne zostanie przeciążone lub
ustawi się skośnie w przedmiocie obrabianym.
Przy robotach na urządzeniu oraz w
trakcie transportu względnie prze-
chowywania urządzenia ustawiaj
przełącznik kierunku obrotów w po-
zycji środkowej (blokada). W ten sposób
zapobiegniesz niezamierzonemu rozruchowi
narzędzia elektrycznego.
Dzieciom lub osobom, którym brak wiedzy lub
doświadczenia w obchodzeniu się z urządze-
niem oraz osobom, które są ograniczone pod
względem ich fizycznych, sensorycznych lub
duchownych zdolności, nie wolno obsługiw
urządzenia bez nadzoru lub wskazówek osoby
odpowiedzialnej za ich bezpieczeństwo. Dzieci
muszą być nadzorowane, aby nie bawiły się
urządzeniem.
Q
Uwaga na przewody!
Podczas pracy przy
użyciu urządzenia upewnij się, że nie ma
zagrożenia natrafienia na przewody
1 / 1

Parkside PABS 12 A1 Operation and Safety Notes

Kategoria
Akumulatorowe wiertarko-wkrętarki udarowe
Typ
Operation and Safety Notes

w innych językach