Whirlpool SISL 106 (EU) instrukcja

GB

1

English, 1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical details

Description of the machine, 4-5

Self-cleaning detergent dispenser drawer

Control panel

Load balancing system

Running a wash cycle, 6

Wash programmes, 7

Detergents and laundry, 8

Preparing the laundry

Washing recommendations

Precautions and advice, 9

General safety

Disposal

Saving energy and respecting the environment

Drip-tray system

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

WASHING MACHINE

SISL 106

Instructions for use

GB

Polski,13

PL

Românã,25

RO

Èeský,37

CZ

Ðóññêèé,49

CIS

2

GB

A

Installation

 This instruction manual should be kept in a safe

place for future reference. If the appliance is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Unpack the washing machine.

2. Make sure that the machine has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: they will be

needed again if the washing machine is moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

Your machine may make a considerable amount of

noise if the two front feet have not been adjusted

correctly.

1. Install the washing machine on a flat and sturdy

floor, without placing it against walls, cabinets or

other furniture.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose and

screw the latter onto a

cold water tap with a 3/4

gas threaded opening

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the machine by

screwing it onto the cold

water inlet of the

appliance, which is

situated on the top right-

hand side of the rear part

of the appliance(see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

GB

3

Technical details

Model

SISL 106

Dimensions

59.5 cm wide

85 cm high

40 cm deep

Capacity

from 1 to 4,5 kg

Electric

connections

please refer to the technical data plate

fixed to the machine

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 40 litres

Spin speed

up to 1000 rpm

Control

programmes

according to EN

60456 directive

programme ;

run with a load of 4,5 kg.

This appliance is compliant with the

following European Community

Directives:

- 73/23/CEE of 19/02/73 (Low

Voltage) and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

- 2002/96/CE

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

alternatively, place it

over the edge of a

basin, sink or tub,

fastening the duct

supplied to the tap (see

figure). The free end of

the hose should not be

underwater.

 We advise against the use of hose extensions; if it

is absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table(see opposite);

 the socket is compatible with the plug of the

appliance. If this is not the case, replace the

socket or the plug.

 The machine must not be installed outdoors, even

in covered areas. It is extremely dangerous to leave

the appliance exposed to rain, storms and other

weather conditions.

 The mains socket must remain within easy reach

after the washing machine has been installed.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

4

GB

Description of the machine

CONTROL

PANEL

PORTHOLE

DOOR

PORTHOLE

DOOR

HANDLE

ACCESS

PANEL FOR

THE DRAIN

PUMP

Self-cleaning detergent dispenser

drawer

This washing machine is fitted with an innovative self-

cleaning detergent drawer which enhances the

quality of each wash.

The drawer is located inside the porthole door.

1. Open the porthole door to access the detergent

dispenser drawer (see figure A).

2. Pour the detergent or the additive into the

compartments, over the protective grilles, as follows:

Compartment

: detergent and additives in

liquid form.

Compartment

: detergent in powder or tablet

form and powder addititves.

To place the tablets inside, lift up the grille

protecting the drawer.

Compartment

: fabric softener.

 Pouring liquid detergent or additives into the central

compartment may cause leakages to occur.

The detergent level can be seen through the corresponding

transparent windows provided on the compartment.

 Inside compartments and , there are also

floating indicators (see figure B) . When the

maximum quantity of detergent/fabric softener has

been measured out, the indicators rise until they

touch the grilles protecting the compartments.

 We recommend that the maximum levels

indicated on the detergent dispenser drawer are

not exceeded.

 We recommend that the dosage instructions on

the detergent packaging are followed carefully. If

using certain particularly thick types of detergent,

we suggest that these are placed directly inside the

drum and not in the detergent dispenser drawer.

Exceeding the maximum levels indicated on the

machine may cause the detergent to leak out of the

bottom part of the drawer.

Exceeding the stated amount of detergent does not

result in a more effective was; it simply pollutes the

environment more.

The water used during the wash cycle will remove

any excess detergent from the drawer. It is, however,

possible to remove the drawer manually (see Care

and Maintenance).

To facilitate the process of measuring out the

detergents, we recommend that the dosing device

supplied with the washing machine is used.

The maximum capacity of the drawer is as follows:

- liquid detergents: 1 1/2 measures

- powder detergents: 2 measures

- fabric softener: 1 measure

M

A

X

M

A

X

STOP

AB

ADJUSTABLE FEET

GB

5

ON/OFF button

DOOR

LOCKED red

indicator

light

WASHING TIME

INDICATOR

lights

START DAILY

WASH 30

PROGRAMME

button

START DELICATES

PROGRAMME

button

START WHITE

COTTON

PROGRAMME

button

START COLOUR

MIX EASY-IRON

PROGRAMME

button

Control panel

ON/OFF button: press this to switch the machine on or off.

When the machine is switched on, the buttons

used to start various programmes begin to flash,

while the washing time indicator lights illuminate in

a fixed manner.

To cancel the cycle, press and hold the on/off button

for approximately 2 seconds while the wash cycle is

in progress.

The

indicator light will flash for a few seconds

and the machine will automatically drain the water in

the tub.

DOOR LOCKED red indicator light:

when the indicator light is illuminated the door is

locked to prevent it being opened accidentally; to

avoid damaging the appliance, wait for the light to

switch off before opening the door after the cycle

has ended or when the cycle is paused. The light

will remain lit for approximately two minutes after

the washing programme has finished.

 Rapid flashing of the DOOR LOCKED indicator light

indicates a fault (see Troubleshooting).

START PROGRAMME buttons:

press one of these to start the selected washing

programme.

- button lit in a fixed manner: programme in progress.

- buttons flashing: awaiting selection.

WASHING TIME INDICATOR lights: these light up

in sequence to indicate the progress of the washing

programme. At the end of the programme all

the indicator lights begin to flash.

For further details, please refer to the chapter entitled

Running a wash cycle.

Load balancing system

To avoid excessive vibrations before every spin, the

machine distributes the load in a uniform manner by

rotating the drum continuously at a speed which is

slightly greater than the washing rotation speed.

When, despite repeated attempts, the load is not

perfectly distributed, the machine spins at a lower

speed than stated for the wash cycle.

If the load is excessively unbalanced, the machine

performs the distribution process instead of spinning.

Balancing attempts may increase the total duration of

the cycle, up to a maximum of 10 minutes.

6

GB

Running a wash cycle

Note: Once the appliance has been installed, and

before you use it for the first time, run a wash cycle

with detergent and no laundry, using the

programme.

1. SWITCH ON THE MACHINE by pressing the ON/

OFF

button. The icons for the START

PROGRAMME buttons begin to flash and the

WASHING TIME INDICATOR lights light up in a

fixed manner, to indicate that the washing machine

is ready to receive instructions.

2. LOAD THE LAUNDRY. Open the door using the

handle. Load the laundry, making sure you do not

exceed the maximum load value indicated in the

table of programmes on the following page.

3. MEASURE OUT THE DETERGENT AND

ADDITIVES.

Pour the detergents into the drawer located inside

the porthole door, taking care not to exceed the

maximum levels indicated on the surface of the

drawer and by the floating indicators. For further

details, please refer to the chapter entitled

Description of the machine.

4. CLOSE THE DOOR.

5. START THE

WASHING

PROGRAMME by

pressing the

corresponding START

PROGRAMME

BUTTON. The icon

corresponding to the

selected programme

illuminates in a fixed

manner, and all the wash time indicator lights

switch off. The DOOR LOCKED indicator light

illuminates in a fixed manner, to signal the

activation of the door safety device.

For a description of the wash programmes

available, please refer to the chapter entitled

Wash programmes.

 The procedure used to start the DELICATES

programme is different; see paragraph "Delicates

30°" on the following page.

During the programme the WASH TIME

INDICATOR lights illuminate in sequence, indicating

how much of the programme has already been

completed.

The diagram at the side

refers to a situation in

which approximately

50% of the cycle has

been completed.

At the end of the cycle,

all the WASHING TIME

INDICATOR lights begin

to flash.

6. The WASH PROGRAMME can be SUSPENDED by

pressing the illuminated start programme button

which begins to flash. After approximately two

minutes the DOOR LOCKED indicator light will

switch off to indicate that the door may be

opened.

If you wish to add more detergent, make sure that

the MAX floating indicator is not in a raised

position.

To restart the wash programme, close the door

again and press the corresponding start button

once more.

To guarantee maximum safety, whenever there is a

quantity of water in the drum which could leak out

of the machine, it will not be possible to open the

door (the DOOR LOCKED indicator light will remain

lit even after the two minutes have passed).

The machine, in this case, should be switched off

by pressing for approximately 2 seconds the ON/

OFF

button, then waiting for the water to be

drained automatically.

7. AT THE END OF THE PROGRAMME

At the end of the wash programme, the icon

corresponding to the selected programme remains

lit in a fixed manner, while all the washing time

indicator lights begin to flash.

To start a new wash cycle the machine must be

switched off and switched back on again, by

pressing the ON/OFF

button TWO TIMES.

GB

7

Wash programmes

*Note: for information relating to excluding the spin cycle in the delicates programme, please refer to the

Delicates 30° paragraph further down the page.

**Note: for information relating to rinsing hand-washed clothes in cold water, please refer to the

Daily wash 30 / Cold water rinse paragraph further down the page.

WHITE COTTON 60°

Designed for the washing of all durable white cotton

garments. Higher washing temperatures offer improved

washing results in Class A appliances.

COLOUR MIX 40° / EASY-IRON

This programme can be used to wash all your coloured

garments, whether cotton or synthetic fabric. The spin

cycle is carefully controlled during the entire wash cycle,

so as to reduce the formation of creases in the fabric

and make it easier to iron.

Cotton and synthetic garments can be washed at the

same time.

DELICATES 30°

A cycle designed for the washing of all woollen, silk and

delicate garments. As these garments have different

features, this programme requires an activation

process which is different from the others:

+ DELICATES CYCLE WITH FINAL SPIN (for

woollen garments): press the START DELICATES

PROGRAMME

button. After approximately 3

seconds, the START DELICATES PROGRAMME

and START DAILY WASH PROGRAMME buttons

begin to flash. Press the START DELICATES

PROGRAMME

button to perform the wash, which

ends with a delicate spin cycle. This programme

includes drum movements which have been carefully

researched to remove excess water from the fabric,

thereby reducing friction and helping to protect your

woollen garments.

+ DELICATES CYCLE WITH SPIN PHASE

EXCLUDED (for silk and viscose garments and for

curtains; not to be used for washing wool):

press the START DELICATES PROGRAMME

button. After approximately 3 seconds, the START

DELICATES PROGRAMME

and START DAILY

WASH PROGRAMME

buttons begin to flash. Press

the START DAILY WASH PROGRAMME

button to

perform the wash without the final spin cycle. At the

end of the cycle, the machine will automatically drain

the water contained in the drum. We recommend that

the garments are removed from the washing machine

straight away, in order to limit the formation of creases.

DAILY WASH 30 / COLD WATER RINSE

This programme can be used to wash lightly soiled

cotton or synthetic fabrics, or garments with the "wash

at 30°"

instruction on the label, in just 30 minutes. It

is also possibile to rinse cotton or synthetic garments

which have been washed by hand (this does not include

wool or silk).

Thanks to its special sensors, the washing machine

is able to recognise when the garments placed in the

drum have detergent on them.

- if no detergent is detected on the clothes, the DAILY

WASH 30' cycle will be performed;

- if detergent is detected (cloths which have been

washed by hand), the COLD WATER RINSE cycle will

be performed automatically.

AUTOMATIC RINSE MANAGEMENT

The rinse function is monitored and controlled in every

programme by special sensors. If the garments are

very soapy at the end of the wash, the rinse cycle

will be extended automatically until the detergent is

removed completely. In this case the wash

programme duration may be slightly increased in relation

to the information given in the table of programmes.

The duration of the programmes indicated in the table are for guidance purposes only, and are calculated based on an average load quantity.

Button Fabrics

Max.

load

(kg)

Te m pe ratu r e

Spin

speed

(rpm)

Cycle

duration

(minutes)

Wash cycle description

WHITE COTTON

Durable white cotton

4,5 60°C 1000 150

Wash cycle, rinse cycles, intermediate

and final spin cycles

COLOR MIX 40° / EASY IRON

Coloured cotton

and synthetics

3 40°C 1000 104

Wash cycle, rinse cycles and delicate

spin cycle

DELICATES

Wool (final delicate spin

cycle)

1 30°C 600 55

Wash cycle, rinse cycles and delicate

spin cycle

Silk and curtains (without

final spin cycle)

130°Cno*50

Wash cycle, rinse cycles and drainage

DAILY

WASH /

COLD WATER RINSE

Cotton and synthetics

3

30°/cold

water**

800 30

Wash cycle (only if the "

Rapid

wash"

programme activated), rinse cycles,

delicate spin cycle

+

8

GB

Washing recommendations

Bed and bathroom laundry (sheets, towels,

bathrobes, etc.): use the WHITE COTTON

programme which guarantees the most efficient

wash in Class A appliances. The intensive spin

cycle eliminates all excess water efficiently.

White cotton garments (shirts, T-shirts,

tablecloths, etc.): use the WHITE COTTON 60°

programme. If there are any stubborn stains, they

should be pre-treated with solid soap before the

wash cycle is started.

Coloured cotton garments (shirts, T-shirts,

underwear, etc.): use the COLOUR MIX 40°

programme, which maximises the performance of

the wash without damaging the colours. The spin

cycle phase, thanks to the incorporated EASY

IRON function, reduces the formation of creases

at the end of the wash, making the fabric easier

to iron. We recommend the use of liquid

detergent.

White or coloured synthetic garments (shirts,

T-shirts, underwear, etc.): use the COLOUR MIX

40°

programme. We recommend that white

and coloured garments are not washed in the

same wash cycle, to prevent any colour leakage

from seeping into the white clothing. We

recommend the use of liquid detergent.

Coloured synthetic and cotton garments, with

wash at 30°

instruction on the care label: use

the DAILY WASH 30

programme. The low

washing temperature protects the coloured fabrics.

We recommend the use of liquid detergent.

Woollen garments (jumpers, scarves, etc.): use

the DELICATES 30° programme with final spin

+ . The movement of the drum during the

wash and the delicate spin cycle reduces fabric

matting. We recommend the use of detergents

specifically designed for woollen garments. We

recommend that the maximum load level is not

exceeded.

Silk garments (shirts, underwear, etc.): use the

DELICATES 30° programme with the spin excluded

+ . Try not to leave the laundry in the drum for

too long after the wash cycle has finished, to

prevent excessive creasing.

Curtains: use the DELICATES 30° programme

with the spin excluded

+ . We recommend

they are folded and placed inside a pillowcase or a

mesh bag. Wash them separately, making sure

the maximum load level is not exceeded.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Detergents and laundry

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label;

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the

buttons.

 Do not exceed the load values indicated for the

Wash programmes.

GB

9

Precautions and advice

 This machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons

and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The machine must only be used by adults, in

accordance with the instructions given in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. this could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the

utmost care. Never try to do this alone, because

the appliance is very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the

environment. The crossed out "wheeled bin"

symbol on the product reminds you of your

obligation, that when you dispose of the appliance

it must be separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Saving detergents, water, energy and time

 To avoid wasting resources, the washing machine

should be used with a full load. One full load instead of

two half loads saves up to 50% of the energy used.

 Treating stains with a stain remover, or leaving

them to soak before they are washed, reduces the

need to wash the garments at high temperatures.

 Use the correct quantity of detergent, in

accordance with the water hardness, how soiled

the garments are and the amount of laundry you

have, in order to avoid wastage and to protect the

environment: although they are biodegradable,

detergents still contain ingredients which alter the

balance of nature. Avoid using fabric softener

wherever possible.

 If you use your washing machine between late

afternoon and the early hours of the morning, you will

help to reduce the peak load of the electricity board.

Drip-tray system

The machine is fitted with a drip-tray system on the

inside of the door, which catches any residual drips of

water at the end of the cycle.

We recommend that the dampness level of the

sponge inside the drip-tray compartment is checked

regularly. If necessary, it may be cleaned or replaced

as follows:

1. Remove the

compartment by applying

a light pressure to the

lower part.

2. Remove the sponge

inside it, rinse it under

running water and wring it

out thoroughly. It may

also be replaced with one

of the spare sponges

provided.

3. Place the sponge back inside the compartment.

4. Replace the compartment in the door, making

sure the springs on the door are correctly

inserted into the corresponding slots on the

compartment.

5. Make sure that the compartment is slotted back

into position correctly.

2

1

10

GB

Care and maintenance

Cutting off the water and electricity

supply

 Turn off the water tap after every wash. This will

limit wear on the hydraulic system in the machine

and help to prevent leaks.

 Unplug the appliance when cleaning it and during

all maintenance work.

Cleaning the machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked in

lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

 We recommend you check that there is no

detergent or water inside the detergent drawer

before removing it. If these substances are present,

proceed with care as they may leak out of the

drawer while it is being removed.

The detergent dispenser drawer in this machine is

cleaned automatically during the wash cycles.

However, residues may form very occasionally after

certain detergents have been used. To clean the

drawer, proceed as follows:

1. Open the door to

access the drawer.

2. Remove the drawer by

pulling upwards, holding it

by the central

compartment as

indicated in the figure. Do

not grip the drawer by

the grille as this may

damage it.

3. Unhook the drawer

cover to access the

compartment, as

indicated in the figure.

4. Clean the drawer

under running water.

5. Re-hook the cover

and replace the drawer,

pushing until it clicks into

place.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. remove the protective

casing on the lower part

of the washing machine,

turning it in an

anticlockwise direction

(see figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. screw the protective cap back on by turning it in a

clockwise direction, making sure the arrow on the

inside part of the cap is facing upwards.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

GB

11

Troubleshooting

Problem:

The washing machine does not

switch on.

The wash cycle wont start.

The washing machine does not fill

with water (the door locked LED

flashes rapidly).

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The DOOR LOCKED indicator light

flashes rapidly.

Too much foam.

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre

(see Service), make sure that the problem is not easily solved using the following list.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making

contact.

 There is no power in the house.

 The washing machine door is not closed properly.

 The ON/OFF button has not been pressed.

 The START PROGRAMME buttons have not been pressed (they

are still flashing).

 The water tap has not been opened.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START PROGRAMME buttons have not been pressed (they

are still flashing).

 The drain hose is not fitted at a height between 65 and 100 cm

from the floor ( see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, shut off the water

tap, switch the appliance off and contact the Technical Assistance

Service. If the dwelling is on one of the upper floors of a building,

there may be problems relating to water drainage, causing the

washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this

inconvenience.

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The protective screws (used during transportation) were not

removed when the appliance was installed. Remove the screws

(see Installation).

 The machine is not level (see Installation).

 The machine is trapped between cabinets and walls (see

Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser is blocked (to clean it, see Care and

maintenance).

 The drain hose is not fixed in place properly (see Installation).

 The drip-tray system is full. Clean the sponge or replace it (see

"Precautions and advice").

 Switch off the machine and unplug it, wait for approximately 1

minute and then switch it back on again. The wash cycle will have

to be started again from the beginning. If the problem persists,

contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should bear

the description for washing machines or hand and machine

wash, or similar instructions).

 Too much detergent was used.

12

GB

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If it has not, contact the Authorised Technical Assistance Service.

 If the machine has been installed or used incorrectly, you may be charged for the maintenance callout

service.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

PL

13

Polski

Spis treci

Instalacja, 14-15

Rozpakowanie i wypoziomowanie

Pod³¹czenie do sieci wodnej i elektrycznej

Dane techniczne

Opis maszyny, 16-17

Samooczyszczaj¹ca siê szufladka na rodki pior¹ce

Panel sterowania

System równowa¿enia za³adunku

W jaki sposób wykonaæ cykl prania, 18

Programy prania, 19

rodki pior¹ce i bielizna, 20

Przygotowanie bielizny

Zalecenia dotycz¹ce prania

Zalecenia i rodki ostro¿noci, 21

Ogólne zasady bezpieczeñstwa

Utylizacja

Oszczêdnoæ i ochrona rodowiska

System zbierania kropel

Utrzymanie i konserwacja, 22

Od³¹czenie wody i pr¹du elektrycznego

Czyszczenie maszyny

Czyszczenie szufladki na rodki pior¹ce

Dbanie o okr¹g³e drzwiczki oraz bêben

Czyszczenie pompy

Kontrola przewodu doprowadzaj¹cego wodê

Nieprawid³owoci w dzia³aniu i sposoby

ich usuwania, 23

Serwis Techniczny, 24

PL

PRALKA

SISL 106

Instrukcja obs³ugi

14

PL

A

Instalacja

 Nale¿y zachowaæ niniejsz¹ ksi¹¿eczkê aby móc z

niej skorzystaæ w ka¿dej chwili. W przypadku

sprzeda¿y, odst¹pienia lub przeniesienia pralki w inne

miejsce, nale¿y zadbaæ o przekazanie ksi¹¿eczki wraz

z maszyn¹, aby nowy w³aciciel móg³ zapoznaæ siê z

dzia³aniem urz¹dzenia i z dotycz¹cymi go

ostrze¿eniami.

 Nale¿y uwa¿nie przeczytaæ instrukcjê obs³ugi:

zawiera ona wa¿ne informacje dotycz¹ce instalacji oraz

w³aciwego i bezpiecznego u¿ytkowania pralki.

Rozpakowanie i wypoziomowanie

Rozpakowanie

1. Rozpakowaæ maszynê.

2. Sprawdziæ, czy maszyna nie zosta³a uszkodzona w

czasie transportu. W przypadku stwierdzenia

uszkodzeñ nie pod³¹czaæ jej i skontaktowaæ siê ze

sprzedawc¹.

3. Odkrêciæ 4 ruby

zabezpieczaj¹ce maszynê

na czas transportu oraz

zdj¹æ gumowy element z

podk³adk¹, znajduj¹cy siê

w tylnej czêci pralki

(patrz rysunek).

4. Zatkaæ otwory przy pomocy plastikowych zalepek,

znajduj¹cych siê w wyposa¿eniu maszyny.

5. Zachowaæ wszystkie czêci: w razie koniecznoci

przewiezienia pralki w inne miejsce nale¿y je ponownie

zamontowaæ.

 Czêci opakowania nie nadaj¹ siê do zabawy dla

dzieci.

Poziomowanie

Maszyna mo¿e dzia³aæ g³ono, jeli nie dokona siê

prawid³owej regulacji dwóch przednich nó¿ek.

1. Ustawiæ pralkê na p³askiej i twardej pod³odze, nie

opieraæ jej o ciany, meble itp.

2. Jeli pod³oga nie jest

idealnie pozioma, nale¿y

skompensowaæ

nierównoci, dokrêcaj¹c

lub odkrêcaj¹c przednie

nó¿ki (patrz rysunek); k¹t

nachylenia, zmierzony na

górnym blacie pralki, nie

powinien przekraczaæ 2°.

Staranne wypoziomowanie pralki zapewnia jej

stabilnoæ i zapobiega wibracjom, ha³asowi oraz

przesuwaniu siê maszyny w czasie pracy. W

przypadku ustawienia pralki na dywanie lub

wyk³adzinie dywanowej nale¿y tak wyregulowaæ nó¿ki,

aby pod pralk¹ pozostawa³a wolna przestrzeñ

niezbêdna dla wentylacji.

Pod³¹czenie do sieci wodnej i elektrycznej

Pod³¹czenie przewodu doprowadzaj¹cego wodê

1. Wsun¹æ uszczelkê A

do koñcówki przewodu

doprowadzaj¹cego wodê i

przykrêciæ go do kurka

zimnej wody z

gwintowanym przy³¹czem

3/4 (patrz rysunek).

Przed pod³¹czeniem

spuszczaæ wodê, a¿

stanie siê ona ca³kowicie

przezroczysta.

2. Pod³¹czyæ do

maszyny przewód

doprowadzaj¹cy wodê,

przykrêcaj¹c go do

odpowiedniego otworu

dop³ywowego,

znajduj¹cego siê w tylnej

czêci pralki, z prawej

strony u góry (patrz

rysunek).

3. Zwróciæ uwagê, aby na przewodzie nie by³o zagiêæ

ani zwê¿eñ.

 Cinienie wody w kurku powinno mieciæ siê w

przedziale podanym w tabeli Danych technicznych

(patrz strona obok).

 Jeli d³ugoæ przewodu doprowadzaj¹cego wodê jest

niewystarczaj¹ca, nale¿y zwróciæ siê do

specjalistycznego sklepu lub do autoryzowanego

technika.

PL

15

65 - 100 cm

Pod³¹czenie przewodu odp³ywowego

Pod³¹czyæ przewód

odp³ywowy, nie zginaj¹c

go, do rury ciekowej lub

do otworu odp³ywowego w

cianie, które powinny

znajdowaæ siê na

wysokoci od 65 do 100

cm od pod³ogi;

albo oprzeæ go na brzegu

zlewu lub wanny,

przymocowuj¹c do kranu

prowadnik, znajduj¹cy

siê w wyposa¿eniu pralki

(patrz rysunek). Wolny

kraniec rury usuwania

wody nie powinien

pozostawaæ zanurzony w

wodzie.

 Odradza siê u¿ywanie rur-przed³u¿aczy; jeli

przed³u¿acz jest jednak konieczny, powinien mieæ on

ten sam przekrój, co rura oryginalna, i nie powinien

przekraczaæ 150 cm d³ugoci.

Pod³¹czenie elektryczne

Przed w³o¿eniem wtyczki do gniazdka elektrycznego

nale¿y siê upewniæ czy:

 gniazdko posiada uziemienie i jest zgodne z

obowi¹zuj¹cymi przepisami;

 gniazdko jest w stanie wytrzymaæ maksymalne

obci¹¿enie mocy maszyny, wskazane w tabeli

Danych technicznych (patrz obok);

 napiêcie zasilania mieci siê w wartociach

wskazanych w tabeli Danych technicznych (patrz

obok);

 gniazdko jest kompatybilne z wtyczk¹ maszyny. W

przeciwnym razie nale¿y wymieniæ gniazdko lub

wtyczkê.

 Nie nale¿y instalowaæ pralki na otwartym powietrzu,

nawet jeli miejsce to jest chronione daszkiem, gdy¿

wystawienie urz¹dzenia na dzia³anie deszczu i burz,

jest bardzo niebezpieczne.

 Po zainstalowaniu maszyny gniazdko elektryczne

powinno byæ ³atwo dostêpne.

 Nie u¿ywaæ przed³u¿aczy ani rozga³êziaczy.

 Kabel nie powinien byæ pogiêty ani przygnieciony.

 Kabel zasilania elektrycznego mo¿e byæ wymieniany

wy³¹cznie przez autoryzowanych techników.

Uwaga! W przypadku nie przestrzegania powy¿szych

warunków producent zwolniony zostanie z wszelkiej

odpowiedzialnoci.

Dane techniczne

Model

SISL 106

Wymiary

szerokoæ cm 59,5

wysokoæ cm 85

g³êbokoæ cm 40

Pojemnoæ

od 1 do 4,5 kg

Dane pr¹du

elektrycznego

dane techniczne umieszczone s¹ na

tabliczce na maszynie

Dane sieci

wodoci¹gowej

Maksymalne cinienie 1 MPa (10 barów)

cinienie minimalne 0,05 MPa (0,5 barów)

pojemnoæ bêbna 40 litrów

Szybkoæ wirowania

do 1000 obrotów na minutê

Programy kontrolne

zgodnie z przepisami

EN 60456

program ;

wykonane przy 4,5 kg za³adowanej

bielizny.

Urz¹dzenie to zosta³o wyprodukowane

zgodnie z nastêpuj¹cymi przepisami EWG:

- 73/23/CEE z dn. 19/02/73 (o Niskim

Napiêciu) wraz z kolejnymi zmianami

- 89/336/CEE z dn. 03/05/89

(o Kompatybilnoci Elektromagnetycznej)

wraz z kolejnymi zmianami

- 2002/96/CE

16

PL

PANEL

STEROWANIA

DRZWICZKI

REGULOWANE NÓ¯KI

UCHWYT

OKR¥G£YCH

DRZWICZEK

Samooczyszczaj¹ca siê szufladka na

rodki pior¹ce

Pralka ta wyposa¿ona jest w innowacyjn¹

samooczyszczaj¹c¹ siê szufladkê na rodki pior¹ce,

która umo¿liwia poprawê jakoci prania.

Szufladka umieszczona jest wewn¹trz okr¹g³ych

drzwiczek.

1. Otworzyæ okr¹g³e drzwiczki, aby uzyskaæ dostêp do

szufladki na rodki pior¹ce (patrz rysunek A).

2. Wlaæ rodek pior¹cy lub dodatek do

w³aciwychpojemników, umieszczonych nad kratkami

zabezpieczaj¹cymi, w nastêpuj¹cy sposób:

Pojemnik

: p³ynny rodek pior¹cy i p³ynne dodatki.

Pojemnik

: rodek pior¹cy w proszku lub w

pastylkach i dodatki w proszku.

Aby w³o¿yæ pastylki, nale¿y podnieæ kratkê

zabezpieczaj¹c¹ umieszczon¹ na szufladce.

Pojemnik : rodek zmiêkczaj¹cy.

 Wlanie p³ynnych rodków pior¹cych lub dodatków do

rodkowego pojemnika mo¿e spowodowaæ ich

niepo¿¹dany wyciek.

M

A

X

M

A

X

DRZWICZKI DOSTÊPU

DO POMPY

ODPROWADZAJ¥CEJ

WODÊ

STOP

W specjalnych przezroczystych okienkach szufladki

mo¿na sprawdziæ poziom rodka pior¹cego.

 Ponadto w pojemnikach

i znajduj¹ siê

wskaniki p³ywakowe (patrz rysunek B). Po

wprowadzeniu maksymalnej iloci rodka

pior¹cego/zmiêkczaj¹cego wskaniki podnosz¹ siê,

dotykaj¹c kratek zabezpieczaj¹cych pojemników.

 Zaleca siê nigdy nie przekraczaæ maksymalnego

poziomu rodków pior¹cych wskazanego na

szufladce.

 Zaleca siê, aby zawsze przestrzegaæ instrukcji

dozowania umieszczonych na opakowaniach

rodków pior¹cych. W przypadku niektórych

szczególnie gêstych rodków pior¹cych zaleca

siê ich wprowadzenie bezporednio do bêbna, a

nie do szufladki na rodki pior¹ce.

Przekroczenie maksymalnego poziomu wskazanego

na maszynie mo¿e spowodowaæ wyciek rodka

pior¹cego do³em szufladki.

Stosowanie nadmiernej iloci rodków pior¹cych nie

poprawia skutecznoci prania, natomiast przyczynia

siê do wiêkszego zanieczyszczenia rodowiska.

Woda wykorzystywana w cyklu prania umo¿liwia

usuniêcie ewentualnego nadmiaru rodka pior¹cego z

szufladki. Istnieje te¿ mo¿liwoæ rêcznego wyjêcia

szufladki (patrz Utrzymanie i konserwacja).

Dla u³atwienia dozowania rodków pior¹cych zaleca

siê u¿ywanie odpowiedniego dozownika, znajduj¹cego

siê w wyposa¿eniu pralki.

Maksymalna pojemnoæ szufladki odpowiada:

- p³ynne rodki pior¹ce: 1 1/2 miarki

- rodki pior¹ce w proszku: 2 miarki

- rodek zmiêkczaj¹cy: 1 miarka

AB

Opis maszyny

PL

17

Przycisk

W£¥CZANIA/

WY£¥CZANIA

Czerwona kontrolka

ZABLOKOWANIA

OKR¥G£YCH

DRZWICZEK

Przycisk W£¥CZANIA/WY£¥CZANIA:

wcisn¹æ go, aby w³¹czyæ lub wy³¹czyæ maszynê.

Kiedy maszyna jest w³¹czona, ikony przycisków

uruchomienia programu zaczynaj¹ pulsowaæ,

natomiast kontrolki wskazuj¹ce czas prania

zaczynaj¹ wieciæ wiat³em ci¹g³ym.

W celu anulowania cyklu nale¿y przytrzymaæ

wciniêty przycisk uruchamiania/wy³¹czania przez

oko³o 2 sekundy w trakcie trwania cyklu prania.

Kontrolka

bêdzie pulsowaæ przez kilka sekund,

maszyna wykonuje w tym czasie automatyczne

usuwanie wody ze zbiornika.

Czerwona kontrolka ZABLOKOWANIA OKR¥G£YCH

DRZWICZEK:

w³¹czona kontrolka wskazuje, ¿e drzwiczki pralki s¹

zablokowane, aby zapobiec ich przypadkowemu

otwarciu; dla unikniêcia uszkodzeñ po zakoñczeniu

cyklu lub po jego wstrzymaniu nie nale¿y otwieraæ

drzwiczek, dopóki kontrolka nie zganie. Czas

oczekiwania po zakoñczeniu programu prania wynosi

oko³o dwóch minut.

 Bardzo szybkie pulsowanie kontrolki

ZABLOKOWANIA OKR¥G£YCH DRZWICZEK

sygnalizuje wyst¹pienie nieprawid³owoci w dzia³aniu

(patrz Nieprawid³owoci w dzia³aniu i sposoby ich

usuwania).

Przyciski URUCHOMIENIA PROGRAMU:

nacisn¹æ, aby uruchomiæ wybrany program prania.

- przycisk wiec¹cy wiat³em sta³ym: program w toku.

- przyciski pulsuj¹ce: w oczekiwaniu na wybór.

Kontrolki

WSKAZUJ¥CE

CZAS PRANIA

Przycisk

URUCHOMIENIA

SZYBKI PROGRAMU

30

Przycisk

URUCHOMIENIA

PROGRAMU

DELIKATNE

Przycisk

URUCHOMIENIA

PROGRAMU

BIA£E

BAWE£NIANE

Przycisk

URUCHOMIENIA

PROGRAMU

KOLOR MIX

£ATWE

PRASOWANIE

Kontrolki WSKAZUJ¥CE CZAS PRANIA:

w³¹czaj¹ siê kolejno, wskazuj¹c stan zaawansowania

programu prania. Po zakoñczeniu programu

wszystkie kontrolki zaczynaj¹ pulsowaæ.

Dok³adniejsze informacje znajduj¹ siê w rozdziale

W jaki sposób wykonaæ cykl prania.

System równowa¿enia za³adunku

W celu unikniêcia nadmiernych wibracji przed ka¿dym

odwirowaniem maszyna rozk³ada ciê¿ar wsadu w

jednolity sposób, nastêpuje to poprzez wykonanie serii

ci¹g³ych obrotów kosza z prêdkoci¹ nieco wy¿sz¹ od

obrotów podczas prania.

Jeli jednak pomimo powtarzanych prób wsad nie

zostanie roz³o¿ony równomiernie, maszyna wykona

wirowanie z prêdkoci¹ ni¿sz¹ od zaprogramowanej.

W przypadku zbyt nierównomiernego roz³o¿enia

wsadu maszyna wykonuje jego równowa¿enie zamiast

odwirowywania.

Ewentualne próby zrównowa¿enia wsadu mog¹

wyd³u¿yæ ³¹czny czas trwania cyklu o maksimum 10

minut.

Panel sterowania

18

PL

Uwaga: Po zainstalowaniu pralki, przed

przyst¹pieniem do jej u¿ytkowania, nale¿y wykonaæ

jeden cykl prania ze rodkiem pior¹cym, lecz bez

wsadu, nastawiaj¹c program

.

1. W£¥CZYÆ MASZYNÊ naciskaj¹c przycisk

W£¥CZANIA/WY£¥CZANIA

. Ikony przycisków

URUCHOMIENIA PROGRAMU zaczynaj¹

pulsowaæ, a kontrolki WSKAZUJ¥CE CZAS

PRANIA zaczynaj¹ wieciæ wiat³em ci¹g³ym,

wskazuj¹c, ¿e pralka jest gotowa do

zaprogramowania.

2. ZA£ADUNEK BIELIZNY. Otworzyæ okr¹g³e drzwiczki

przy pomocy w³aciwej klamki. W³o¿yæ bieliznê

uwa¿aj¹c, aby nie przekroczyæ wielkoci za³adunku

wskazanej w tabeli programów na nastêpnej stronie.

3. DOZOWANIE RODKÓW PIOR¥CYCH I

DODATKÓW

rodki pior¹ce nale¿y dozowaæ do szufladki

umieszczonej wewn¹trz okr¹g³ych drzwiczek, nie

przekraczaj¹c poziomów maksymalnych

zaznaczonych na zewn¹trz szufladki oraz

wskazywanych przez specjalne wskaniki

p³ywakowe. Dok³adniejsze informacje znajduj¹ siê w

rozdziale Opis maszyny.

4. ZAMKN¥Æ OKR¥G£E DRZWICZKI.

5. URUCHOMIÆ

PROGRAM PRANIA,

wciskaj¹c odpowiedni

PRZYCISK

URUCHOMIENIA

PROGRAMU. Ikona

odpowiadaj¹ca

wybranemu programowi

zaczyna siê wieciæ

wiat³em ci¹g³ym,

natomiast wszystkie

kontrolki wskazuj¹ce czas prania gasn¹. Kontrolka

ZABLOKOWANIA OKR¥G£YCH DRZWICZEK

zaczyna siê wieciæ wiat³em ci¹g³ym, sygnalizuj¹c

blokadê bezpieczeñstwa drzwiczek.

Opis dostêpnych programów prania znajduje siê w

rozdziale Programy prania.

 Sposób uruchamiania programu DELIKATNE

jest inny, patrz paragraf Delikatne 30° na

nastêpnej stronie.

W trakcie trwania programu kontrolki WSKAZUJ¥CE

CZAS PRANIA w³¹czaj¹ siê kolejno, aby wskazaæ

jaka czêæ programu zosta³a ju¿ wykonana.

Rysunek umieszczony

obok obrazuje sytuacjê,

w której zosta³o ju¿

wykonane oko³o 50%

cyklu.

Po zakoñczeniu cyklu

wszystkie kontrolki

WSKAZUJ¥CE CZAS

PRANIA s¹ w³¹czone i

pulsuj¹.

6. Istnieje mo¿liwoæ WSTRZYMANIA PROGRAMU

PRANIA poprzez naciniêcie zawieconego

przycisku uruchomienia programu, który zaczyna

pulsowaæ. Po zakoñczeniu programu zganie

kontrolka ZABLOKOWANIA OKR¥G£YCH

DRZWICZEK, co wskazuje, ¿e mo¿na je otworzyæ.

Jeli chce siê dodaæ wiêcej rodka pior¹cego,

nale¿y zwróciæ uwagê, aby wskanik p³ywakowy

MAX nie by³ podniesiony.

Aby ponownie uruchomiæ program, nale¿y zamkn¹æ

drzwiczki i jeszcze raz nacisn¹æ odpowiedni

przycisk uruchomienia.

Dla zapewnienia maksymalnego bezpieczeñstwa,

jeli w bêbnie znajduje siê taka iloæ wody, która

mog³aby wyp³yn¹æ na zewn¹trz, nie jest mo¿liwe

otwarcie okr¹g³ych drzwiczek (kontrolka

ZABLOKOWANE DRZWICZKI pozostaje w³¹czona

równie¿ po up³ywie dwóch minut). W takim

przypadku nale¿y wy³¹czyæ maszynê, trzymaj¹c

wciniêty przez oko³o 2 sekundy przycisk

W£¥CZANIA/WY£¥CZANIA

, i poczekaæ na

automatyczne usuniêcie wody.

7. KONIEC PROGRAMU

Po zakoñczeniu programu prania ikona

odpowiadaj¹ca wybranemu programowi dalej wieci

wiat³em ci¹g³ym, natomiast wszystkie kontrolki

wskazuj¹ce czas prania zaczynaj¹ pulsowaæ.

Aby uruchomiæ nowy cykl prania, nale¿y wy³¹czyæ i

ponownie w³¹czyæ maszynê, DWUKROTNIE

naciskaj¹c przycisk W£¥CZANIA/WY£¥CZANIA

.

W jaki sposób wykonaæ

cykl prania

PL

19

BAWE£NIANE BIA£E 60°

Przeznaczony do prania najbardziej wytrzyma³ych,

bia³ych bawe³nianych tkanin. Wy¿sza temperatura

umo¿liwia uzyskanie najlepszych rezultatów prania w

klasie A.

KOLOR MIX 40° / £ATWE PRASOWANIE

W tym programie mo¿na praæ dowolne kolorowe

tkaniny, zarówno bawe³niane, jak i syntetyczne.

Odwirowywanie jest dok³adnie kontrolowane w ca³ym

cyklu prania, aby ograniczyæ gniecenie siê tkanin, a

tym samym u³atwiæ ich prasowanie.

Mo¿na praæ równoczenie tkaniny bawe³niane i

syntetyczne.

DELIKATNE 30°

Cykl przeznaczony do prania tkanin z we³ny, jedwabiu

oraz z najbardziej delikatnych. Z uwagi na odmienne

w³aciwoci tego rodzaju tkanin, uruchomienie

omawianego programu jest inne ni¿ pozosta³ych:

+ CYKL DELIKATNE Z ODWIROWANIEM

KOÑCOWYM (do tkanin we³nianych): nacinij przycisk

URUCHOMIENIE PROGRAMU DELIKATNE

. Po

oko³o 3 sekundach przyciski URUCHOMIENIA

PROGRAMU DELIKATNE

i URUCHOMIENIA

PROGRAMU SZYBKIEGO zaczynaj¹ pulsowaæ.

Nacinij ponownie przycisk URUCHOMIENIA

PROGRAMU DELIKATNE

, aby wykonaæ cykl

prania, który koñczy siê delikatnym odwirowaniem.

Program ten przewiduje obroty bêbna opracowane

specjalnie w celu umo¿liwienia usuwania nadmiaru

wody z materia³ów, aby ograniczyæ przecieranie siê

w³ókien i w ten sposób chroniæ tkaniny z we³ny.

+ CYKL DELIKATNE BEZ ODWIROWANIA (do

tkanin z jedwabiu i wiskozy oraz do prania zas³on; nie

nale¿y go u¿ywaæ do prania we³ny): nacinij przycisk

URUCHOMIENIE PROGRAMU DELIKATNE

.

Po oko³o 3 sekundach przyciski URUCHOMIENIA

PROGRAMU DELIKATNE

i URUCHOMIENIA

PROGRAMU SZYBKIEGO

zaczynaj¹ pulsowaæ.

Nacinij przycisk URUCHOMIENIA PROGRAMU

SZYBKIEGO

, aby wykonaæ cykl prania bez

odwirowania koñcowego. Po zakoñczeniu cyklu

maszyna automatycznie odprowadzi wodê z bêbna.

Zaleca siê wyj¹æ pranie z pralki zaraz po zakoñczeniu

cyklu, aby unikn¹æ powstania nadmiernych zagnieceñ.

SZYBKI 30 / TYLKO P£UKANIE

Przy zastosowaniu tego programu mo¿na wypraæ w

ci¹gu 30 minut ma³o zabrudzone tkaniny bawe³niane,

syntetyczne lub ze wskazówk¹ na etykiecie pranie w

30° . Mo¿na ponadto wykonaæ szybkie p³ukanie

tkanin bawe³nianych lub syntetycznych wczeniej

wypranych rêcznie (z wyj¹tkiem we³ny i jedwabiu).

Dziêki odpowiednim czujnikom pralka jest w

stanie wykryæ obecnoæ rodka pior¹cego w

tkaninach znajduj¹cych siê w bêbnie:

- jeli na tkaninach nie ma rodka pior¹cego,

wykonany zostanie cykl SZYBKI 30';

- jeli jest rodek pior¹cy (tkaniny wczeniej wyprane

rêcznie), automatycznie wykonany zostanie cykl

TYLKO P£UKANIE.

AUTOMATYCZNE STEROWANIE P£UKANIAMI

W ka¿dym programie funkcja p³ukania jest

kontrolowana przez odpowiednie czujniki. Jeli tkaniny

pod koniec cyklu prania bêd¹ nadmiernie namydlone,

faza p³ukania zostanie automatycznie przed³u¿ona a¿

do ca³kowitego usuniêcia rodka pior¹cego. W takim

przypadku czas trwania programu prania mo¿e byæ

nieco d³u¿szy w stosunku do czasu wskazanego w

tabeli programów.

*Uwaga: informacje dotycz¹ce wy³¹czenia odwirowywania w programie delikatne znajduj¹ siê w paragrafie

Delikatne 30° na dole strony.

**Uwaga: informacje dotycz¹ce wykonania samego p³ukania w zimnej wodzie ubrañ wczeniej wypranych rêcznie

znajduj¹ siê w paragrafie Szybki 30'/Tylko p³ukanie na dole tej strony.

Czasy trwania programów wskazane w tabeli maj¹ charakter czysto orientacyjny i zosta³y obliczone dla redniej iloci ³adunku.

Programy prania

Tasta

Rodzaj tkaniny oraz

stopieñ zabrudzenia

£adune

k maks.

(kg)

Temperatury

Odwirowy

wanie

(obroty na

minutê)

Czas

trwania

cyklu

(minuty)

Opis cyklu prania

BIA£E BAWE£NA

Bawe³niane bia³e

wytrzyma³e

4,5 60°C 1000 150

Pranie, p³ukania, odwirowania

porednie i koñcowe

KOLOR MIX 40° / £ATWE PRASOW ANIE

Bawe³niane i

syntetyczne kolorowe

3 40°C 1000 104

Pranie, p³ukania, delikatne

odwirowanie

DELIKATNE

We³na (delikatne

odwirowanie koñcowe)

1 30°C 600 55

Pranie, p³ukania, delikatne

odwirowanie

Jedwab i zas³ony

(bez odwirowania

koñcowego)

1 30°C

bez

wirowania*

50 Pranie, p³ukania, opró¿nienie z wody

SZYBKI 30 / TYLKO P£UKANIE

Bawe³niane i

syntetyczne

3

30°/zimna

woda**

800 30

Pranie (tylko w przypadku

w³¹czenia programu "Szybkiego),

p³ukania, delikatne odwirowanie

+

20

PL

Zalecenia dotycz¹ce prania

Bielizna pocielowa i ³azienkowa

(przecierad³a, rêczniki, szlafroki itp.): zastosuj

program BAWE£NIANE BIA£E 60°

, który

gwarantuje najlepsze wyniki prania w klasie A.

Silne wirowanie umo¿liwia skuteczn¹ eliminacjê

nadmiaru wody.

Bia³a bielizna bawe³niana (koszule, bluzki,

obrusy itp.): zastosuj program BAWE£NIANE

BIA£E 60°. W przypadku obecnoci uporczywych

plam przed wykonaniem cyklu prania zaleca siê je

wstêpnie zapraæ myd³em w kostce.

Kolorowa bielizna bawe³niana (koszule,

bluzki, bielizna osobista itp.): zastosuj program

KOLOR MIX 40°

, który zapewnia najlepsze

wyniki prania, nie niszcz¹c kolorów. Faza

odwirowywania, dziêki funkcji £ATWE

PRASOWANIE, umo¿liwia zmniejszenie iloci

zagnieceñ pod koniec cyklu prania, u³atwiaj¹c

prasowanie. Zaleca siê stosowanie p³ynnego

rodka pior¹cego.

Bielizna z tkanin syntetycznych, bia³a lub

kolorowa (koszule, bluzki, bielizna osobista

itp.): zastosuj program KOLOR MIX 40°

. Zaleca

siê nie praæ równoczenie tkanin bia³ych i

kolorowych w tym samym cyklu prania, aby

unikn¹æ ewentualnego zafarbowania bia³ych tkanin

przez kolorowe. Zaleca siê stosowanie p³ynnego

rodka pior¹cego.

Kolorowe tkaniny bawe³niane lub syntetyczne

ze wskazówk¹ na etykiecie pranie w 30°

:

zastosuj program SZYBKI 30

. Niska temperatu-

ra prania zapewnia najwy¿sz¹ ochronê kolorów.

Zalecamy stosowanie p³ynnego rodka pior¹cego.

Tkaniny we³niane (swetry, szaliki itp.): zastosuj

program DELIKATNE 30° z odwirowaniem

koñcowym

+ . Obroty bêbna podczas prania

i w fazie delikatnego odwirowywania zmniejszaj¹

filcowanie siê tkanin. Zaleca siê stosowanie

specjalnych rodków pior¹cych do we³ny. Zaleca

siê nie przekraczanie maksymalnego poziomu

za³adunku.

Tkaniny jedwabne (koszule, bielizna itp.):

zastosuj program DELIKATNE 30° bez odwirowania

koñcowego

+ . Po zakoñczeniu cyklu nie

pozostawiaj zbyt d³ugo prania w bêbnie, aby

unikn¹æ powstania nadmiernych zagnieceñ.

Firany: zastosuj program DELIKATNE 30° bez

odwirowania koñcowego

+ . Zaleca siê

z³o¿yæ je i umieciæ w poszewce lub w siatkowym

worku. Praæ je osobno uwa¿aj¹c, aby nie

przekroczyæ maksymalnego poziomu za³adunku.

Ile wa¿y bielizna?

1 przecierad³o 400-500 gr.

1 poszewka 150-200 gr.

1 obrus 400-500 gr.

1 szlafrok 900-1.200 gr.

1 rêcznik 150-250 gr.

1 d¿insy 400-500 gr.

1 koszula 150-200 gr.

rodki pior¹ce i bielizna

Przygotowanie bielizny

 Podzieliæ bieliznê do prania wed³ug:

- rodzaju tkaniny / symbolu na etykietce.

- kolorów: oddzieliæ tkaniny kolorowe od bia³ych.

 Opró¿niæ kieszenie i sprawdziæ guziki.

 Nie przekraczaæ wartoci maksymalnego ³adunku

wskazanych w Programy prania.

Strona jest ładowana ...

Whirlpool SISL 106 (EU) instrukcja

Whirlpool SISL 106 (EU) instrukcja

w innych językach

Powiązane dokumenty

Inne dokumenty