Yamaha RS150 Assembly Instructions

Yamaha
Marka
Yamaha
Model
RS150
Kategoria
Instrumenty muzyczne
Typ
Assembly Instructions

Ten podręcznik jest również odpowiedni dla

■ Handling Precautions
• Do not alter the product. Doing so may result in damage or deterioration to the product.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to
a heater, in a closed car, etc.) or damp (bathroom, outside on a rainy day, etc.). It may result in deformation,
discoloration, stickiness, damage or deterioration.
•To clean the product, please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been
wrung out thoroughly to remove any remaining detergent.
Do not use benzine, thinner or alcohol as it may
result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come
into contact with the cushions used in the product, it may result in deterioration.
Before using, please read this “Assembly In-
struction” sheet, and use this product in a safe
and proper manner.
Especially for children, parents or an instructor
should teach the children the proper manner in
which to use the device.
PRECAUTIONS
Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the
instrument being unstable and overturning.
Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.
When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop, the rack or pipes may slip, pinching or
causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.
Please be careful when children are close to or touching the product. The product has many pipes and arms so careless
movement around the product may result in injury.
When setting the pads and modules, please pay close attention in regards to the handling and setting of cables. Feet may
become entangled in the cables resulting in falls.
Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.
Caution (including danger, or warning). This
mark indicates cautions in which you should
pay close attention to.
Acts indicated with this icon are prohibited and
should not be attempted.
To prevent against accidents and injury
Please follow the cautions listed below
* Specifications are subject to change without notice.
If this symbol is ignored and the equipment is used improperly, fatal injury to per-
sons or serious damage could occur.
WARNING
CAUTION
If this symbol is ignored and the equipment is used improperly, there is a danger
of injury to persons handling the equipment, and material damage could occur.
■ RS150 Assembly
* Parts for the RS150's main structure have already been assembled before packing. After removing the unit from the box, follow the instructions described below to complete the assembly.
A Phillips (+) screwdriver is required when attaching the DTXTREME
II
S. Please prepare one before starting assembly.
After removing the unit from the box, remove all cushion material.
1
2
Setting up the parts
INTRODUCTION
Thank you for purchasing the Yamaha Electronic Drum Rack System RS150.
Before using, thoroughly read these assembly instructions, and use this product
safely and correctly.
■ Inside This Package
Before setup, please make sure that all of the items listed below are present and ac-
counted for. If anything is missing, please contact the dealer from whom you purchased
the unit.
Module Holder
Piller (C)
Piller (R)
Piller (L)
$
Caution
Leg (L)
Leg (C)
Leg (R)
t
r
y
i
q
e
w
Remove temporarily.
* Before assembling the rack stand, make sure all of the parts shown below are included.
ASSEMBLY INSTRUCTIONS
u
o
o
o
o
o
o
Cymbal Holder
(CH740)
Cymbal Holder
(CH740)
Cymbal Holder
(CH745)
Tom Clamp
(CL-940A)
Tom Clamp
(CL-940A)
Tom Clamp
(CL-940A)
Memory Clamps
Using the memory clamps let you obtain the same
height setting for all future setups.
Holder Clamp
Holder Clamp
Caution : Make sure the bolts marked with a " " are loosened before setting up.
Leg Connector
Center Pipe (A)
Center Pipe (B)
Center Pipe (C)
Center Pipe (D)
Leg Connector
Holder Clamp
Holder Clamp
Leg Connector
Cross Pipe
Holder Clamp Holder Clamp
Holder Clamp
Holder Clamp
Tighten knob of
leg connector
q Temporarily remove the leg connector from pillar (R).
w Attach center pipe (D) to pillar (R) and pillar (C), and secure.
e Reattach the leg connector.
r Attach the cross pipe to the leg connector.
t Attach center pipe (C) to pillar (L) and pillar (C), and secure.
y Attach center pipe (B) to pillar (R) and pillar (C), and secure.
u Attach center pipe (A) to pillar (L) and pillar (C), and secure.
i Attach the module holder to pillar (L), and secure.
o Attach the cymbal holders and tom clamps to the holder clamps, and secure.
Follow the setup order (q~o) in the diagrams shown below.
■ Set up example
Printed in Indonesia
WG24090
■ Optional Parts
● Pad and Drum Trigger Grouping
● Monitor System and Attachement Grouping
e PCY150S
Cymbal Pad
q DTXTREME
II
S
Drum Trigger Module
w PCY130/130S
Cymbal Pad
t TP100
Drum Pad
y TP120SD
Drum Pad
u KP65
Kick Pad
r RHH130
Real Hi-hat Pad
i Foot Pedal
* DFP-9310 etc.
o Snare Stand
*SS652 etc.
!0 Hi-hat Stand
*HS-740 etc.
• SPAT1
(1 set L/R units)
• TPCL150
• CYAT150
• MS50DR
• Sub Woofer
amp unit
• MS100DR
• Sub Woofer
amp unit
• Satellite
Speakers
• Satellite
Speakers
Sub Woofer amp unit
t
t
q
i
y
e
w
r
o
!0
u
w
Satellite Speaker
Satellite Speaker
PCY130
PCY150S
PCY130S
Maker sure all bolts on clamps, pads, etc., are tightened firmly.
However, loose or over-tightened bolts may result in the part falling off and/or damage. Please use caution.
After assembly is complete, setup the kick pad, real hi-hat pad, etc., and connect the cables. Use the supplied cable bands to secure the cables
to the frame pipes to keep cables out of the way during performance.
If the rack is moved even after setup is complete, make sure the bolts are loosened before moving the rack.
Attaching the cymbal pads
4
Attach the cymbal pads to the cymbal holders and adjust their
position, then secure in place. (Please refer to the Owner's
Manual that came with the cymbal pads on attaching the cym-
bal pads.)
DTXTREME
II
S
Drum Pad
Cymbal Pad
(PCY130/130S/150S)
Anti-swivel brace
(supplied with the
(PCY130/130S/150S)
Felt
Module
Holder
Step 3-1
Step 3-2
Holder Clamp
Step 5
Step 4
Attaching the DTXTREME
II
S
3
3-1 Remove the module holder from the holder clamp, and
use the supplied screws to attach the DTXTREME
II
S.
Make sure only the supplied screws are used. Using any
other screws may result in the unit falling off the holder
or damage.
3-2 Slide the module holder, with the DTXTREME
II
S already
attached, into the holder clamp.
Attaching the drum pads
5
Attach the drum pads to the tom clamp and adjust their posi-
tion, then secure in place.
Step 3
  • Page 1 1
  • Page 2 2

Yamaha RS150 Assembly Instructions

Yamaha
Marka
Yamaha
Model
RS150
Kategoria
Instrumenty muzyczne
Typ
Assembly Instructions
Ten podręcznik jest również odpowiedni dla
ściągnij PDF
raport

w innych językach

Powiązane dokumenty