Yamaha Arius YDP-140 Instrukcja obsługi

Marka: Yamaha

Model: Arius YDP-140

Kategoria: Instrumenty muzyczne

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

YDP-160

YDP-140

For information on assembling the keyboard stand, refer to the instructions at the end of this manual.

IMPORTANT — Check your power supply — (YDP-160)

Make sure that your local AC mains voltage matches the voltage specified on the name plate on the bottom

panel. In some areas a voltage selector may be provided on the bottom panel of the main keyboard unit near the

power cord. Make sure that the voltage selector is set for the voltage in your area. The voltage selector is set at

240V when the unit is initially shipped.

To change the setting use a "minus" screwdriver to rotate the selector dial so that the correct voltage appears

next to the pointer on the panel.

Owner's Manual

YDP-160/140 Owner’s Manual

Introduction

92-469 1 (bottom)

SPECIAL MESSAGE SECTION (for YDP-160)

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these

graphics appears on this page. Please observe all cautions

indicated on this page and those indicated in the safety

instruction section.

See bottom of Keyboard enclosure for graphic symbol markings.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servic-

ing) instructions in the literature

accompanying the product.

The lightning ﬂash with arrowhead

symbol, within the equilateral trian-

gle, is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s enclo-

sure that may be of sufﬁcient magni-

tude to constitute a risk of electrical

shock.

IMPORTANT NOTICE: All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is

properly installed and used in its normal and customary

manner, all foreseeable risks have been eliminated. DO

NOT modify this unit or commission others to do so

unless speciﬁcally authorized by Yamaha. Product perfor-

mance and/or safety standards may be diminished.

Claims ﬁled under the expressed warranty may be denied

if the unit is/has been modiﬁed. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the speciﬁcations

without notice or obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is

approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to

perform the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the man-

ufacturer’s warranty, and are therefore the owners respon-

sibility. Please study this manual carefully and consult

your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Model

Serial No.

Purchase Date

YDP-160

YDP-160/140 Owner’s Manual

PLEASE KEEP THIS MANUAL

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or speciﬁcally

recommended by Yamaha.

WARNING: Do not place this product in a position where anyone

could walk on, trip over ,or roll anything over power or connecting

cords of any kind. The use of an extension cord is not recom-

mended! If you must use an extension cord, the minimum wire size

for a 25’ cord (or less ) is 18 AWG. NOTE: The smaller the AWG

number ,the larger the current handling capacity. For longer exten-

sion cords, consult a local electrician.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is

used, please observe all safety markings and instructions that

accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change

or modify any of the speciﬁcations without notice or obligation to

update existing units.

This product, either alone or in combination with an ampliﬁer and

headphones or speaker/s, may be capable of producing sound levels

that could cause permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level that is uncomfort-

able. If you experience any hearing loss or ringing in the ears, you

should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and / or accessory

mounting ﬁxtures that are either supplied with the product or as

optional accessories. Some of these items are designed to be

dealer assembled or installed. Please make sure that benches are

stable and any optional ﬁxtures (where applicable) are well secured

BEFORE using.

Benches supplied by Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how

a function or effect works (when the unit is operating as designed)

are not covered by the manufacturer’s warranty, and are therefore

the owners responsibility. Please study this manual carefully and

consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and

environmentally friendly. We sincerely believe that our products and

the production methods used to produce them, meet these goals. In

keeping with both the letter and the spirit of the law, we want you to

be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately ﬁve years. When replacement becomes

necessary, contact a qualiﬁed service representative to perform the

replacement.

This product may also use “household” type batteries. Some of

these may be rechargeable. Make sure that the battery being

charged is a rechargeable type and that the charger is intended for

the battery being charged.

When installing batteries, do not mix batteries with new, or with bat-

teries of a different type. Batteries MUST be installed correctly. Mis-

matches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly and

as regulated by the laws in your area. Note: Check with any retailer

of household type batteries in your area for battery disposal informa-

tion.

Disposal Notice:

Should this product become damaged beyond repair, or for some

reason its useful life is considered to be at an end, please observe

all local, state, and federal regulations that relate to the disposal of

products that contain lead, batteries, plastics, etc. If your dealer is

unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this man-

ual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

YDP-140

SPECIAL MESSAGE SECTION (for YDP-140)

92-BP (bottom)

(1)B-12/(3)-11

YDP-160/140 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Use only the supplied power cord/plug.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• (Users within Canada or U.S.) Use the speciﬁed adaptor (PA-150 or an

equivalent recommended by Yamaha) only. Using the wrong adaptor can result

in damage to the instrument or overheating.

• (Others) Use the speciﬁed adaptor (PA-5D or an equivalent recommended by

Yamaha) only. Using the wrong adaptor can result in damage to the instrument

or overheating.

• Do not place the AC adaptor cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy objects

on it, or place it in a position where anyone could walk on, trip over, or roll

anything over it.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings. If any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet. Then have

the instrument inspected by qualiﬁed Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the power cord (YDP-160)/AC adaptor cord (YDP-140) or plug becomes

frayed or damaged, or if there is a sudden loss of sound during use of the

instrument, or if any unusual smells or smoke should appear to be caused by it,

immediately turn off the power switch, disconnect the electric plug from the

outlet, and have the instrument inspected by qualiﬁed Yamaha service

personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• (YDP-160) Remove the electric plug from the outlet when the instrument is not

to be used for extended periods of time, or during electrical storms.

• (YDP-140) Unplug the AC power adaptor when not using the instrument, or

during electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Read carefully the attached documentation explaining the assembly process.

Failure to assemble the instrument in the proper sequence might result in

damage to the instrument or even injury.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disﬁguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio

may generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• (YDP-160) Before moving the instrument, remove all connected cables.

• (YDP-140) Before moving the instrument, remove all connected adaptor and

other cables.

Power supply

Power cord (YDP-160)

AC power adaptor(YDP-140)

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord/AC power adaptor

Assembly

Location

(1)B-12/(3)-11

YDP-160/140 Owner’s Manual

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still ﬂowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the AC power plug (YDP-160)/AC power adaptor (YDP-140) from the wall AC

outlet.

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all

components, set all volume levels to minimum. Also, be sure to set the volumes

of all components at their minimum levels and gradually raise the volume

controls while playing the instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry or slightly damp cloth. Do not use

paint thinners, solvents, cleaning ﬂuids, or chemical-impregnated wiping

cloths.

•Take care that the key cover does not pinch your ﬁngers, and do not insert a

ﬁnger or hand in any gaps on the key cover or instrument.

• Never insert or drop paper, metallic, or other objects into the gaps on the key

cover, panel or keyboard. If this happens, turn off the power immediately and

unplug the power cord from the AC outlet. Then have the instrument inspected

by qualiﬁed Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument or headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

• Do not place the bench in an unstable position where it might accidentally fall

over.

• Do not play carelessly with or stand on the bench. Using it as a tool or step-

ladder or for any other purpose might result in accident or injury.

• Only one person should sit on the bench at a time, in order to prevent the

possibility of accident or injury.

• If the bench screws become loose due to extensive long-term use, tighten them

periodically using the included tool.

Saving and backing up your data

• Data in the instrument’s internal memory can be lost due to operational errors or

malfunction. Be sure to save any important data to external media via a

computer connected to the instrument. (page 32)

Always turn the power off when the instrument is not in use.

YDP-160

Even when the power switch is turned off, electricity is still ﬂowing to the instrument at the minimum level. When you are not using the instrument for a long time, make sure

you unplug the AC power plug from the wall AC outlet.

YDP-140

Even when the power switch is in the “STANDBY” position, electricity is still ﬂowing to the instrument at the minimum level. When you are not using the instrument for a long

time, make sure you unplug the AC power adaptor from the wall AC outlet.

Connections

Maintenance

Handling caution

Using the bench (If included)

Saving data

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

Welcome

YDP-160/140 Owner’s Manual

Welcome

Thank you for purchasing the Yamaha Digital Piano! We recommend that you read this manual carefully so that you can

take full advantage of the advanced and convenient functions of your new digital piano.

We also recommend that you keep this manual in a safe, convenient place for future reference.

About the Documentation and Refer-

ence Materials for this Instrument

The documentation and reference materials for this instrument consist of the following:

Owner’s Manual (this book)

Introduction (P2):

Please read this section ﬁrst.

Reference (P16):

This section explains how to make detailed settings for the instrument’s various functions.

Appendix (P41):

This section introduces speciﬁcations and other information.

Quick Operation Guide (separate sheet)

This Guide explains detailed operation of the functions assigned to the buttons and keyboard.

Data List

You can download various MIDI-related reference materials, such as the MIDI Data Format and MIDI Implementa-

tion Chart, from the Yamaha Manual Library.

Connect to the Internet, visit the following website, type the model name of your instrument (such as “YDP-160”) in

the Model Name text box, then click the Search button.

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

•The illustrations as shown in this owner’s manual are for instructional purposes only, and may be different from the

ones on your instrument.

Trademarks:

•Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.

•The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with

respect to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all

computer software, style ﬁles, MIDI ﬁles, WAVE data, musical scores and sound recordings. Any unauthorized use of

such programs and contents outside of personal use is not permitted under relevant laws. Any violation of copyright

has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is

strictly prohibited except for your personal use.

Accessories

YDP-160/140 Owner’s Manual

Accessories

• Owner’s Manual (this book)

• Quick Operation Guide (separate sheet)

• “50 Greats for the Piano” (Music Book)

• AC Power cord (YDP-160)

• Bench*

• AC Power adaptor (YDP-140)*

Users within Canada or U.S.: PA-150 or an equivalent

Others: PA-5D or an equivalent

* Included or optional depending on locale.

Tuning

Unlike an acoustic piano, this instrument does not need to be tuned. It always stays perfectly in tune.

Transporting

If you move to another location, you can transport this instrument along with your other belongings. You can move

the unit as it is (assembled) or you can disassemble the unit before moving.

Tr ansport the keyboard horizontally. Do not lean it up against a wall or stand it up on its side. Do not subject the

instrument to excessive vibration or shock.

Features

YDP-160/140 Owner’s Manual

Features

AWM Dynamic Stereo Sampling

The Yamaha YDP-160/140 digital piano offers a rich and versatile range of sounds, which are created using Yamaha’s

proprietary sampling tone-generation system, “AWM Dynamic Stereo Sampling.”

The AWM (Advanced Wave Memory) is a sampling system which creates sound close to that of an acoustic instru-

ment by using digital technology to record the instrument sound and applying high-quality digital ﬁlter technology

to the recorded audio samples.

The waveform of the sound created by playing the key of an acoustic piano differs depending on the playing

strength from pianissimo to fortissimo. The AWM Dynamic Stereo Sampling can produce such dynamic nuances by

recording samples of various playing strengths. The greater the number of samples used, the higher the expressive

quality and potential becomes.

Two of the piano voices, “Grand Piano 1” and “Grand Piano 2,” feature totally new samples recorded from a full-size

concert grand piano.

The “Grand Piano 1” voice features multiple wave samples for different velocities (Dynamic Sampling); that is, dif-

ferent samples are used depending on how fast or strong you strike the keys. Therefore, this voice expresses detailed

dynamics and sounds much closer to a true acoustic piano.

GH(Graded Hammer) keyboard

and GHS(Graded Hammer Standard) keyboard with matte black keytops

A special Graded Hammer keyboard on the YDP-160, and Graded Hammer Standard keyboard with matte black

keytops on the YDP-140, feature graded key weight and response throughout the keyboard range. They respond to a

heavier touch in the low range of the keyboard and a lighter touch in the higher range of the keyboard, thus provid-

ing natural grand-piano type playability. The matte ﬁnish of the black keys enhances keyboard’s luxurious appear-

ance. The Graded Hammer keyboard also offers superb playability for tremolo and other repetitive-striking

techniques.

Table of Contents

YDP-160/140 Owner’s Manual

Table of Contents

Introduction

SPECIAL MESSAGE SECTION ...................... 2

About the Documentation and Reference

Materials for this Instrument...................... 6

Accessories .................................................. 7

Features....................................................... 8

Part Names and Functions........................ 10

Before Using the Digital Piano ................. 12

Key Cover ..........................................................12

Music Rest .........................................................12

Connecting the Power Cord (YDP-160) .........13

Connecting the Power Adaptor (YDP-140) ....13

Turning the Power On......................................14

Setting the Volume............................................14

Using Headphones............................................15

Reference

Listening to the Demo Songs ................... 16

Listening to 50 Piano Preset Songs .......... 17

Listening to Songs Loaded from the

Computer .................................................. 18

Selecting & Playing Voices........................ 19

Selecting Voices.................................................19

Using the Pedals ................................................20

Adding Variations to the Sound – Reverb.......21

Layering Two Voices (Dual mode) ..................22

Transposition ....................................................23

Fine-tuning the Pitch........................................23

Using the Metronome.......................................24

Adjusting the Keyboard Touch (Touch

Sensitivity) .........................................................25

Recording your Performance.................... 26

Playing Back Recorded Performance Data ......27

Erasing Recorded Performance Data ...............27

Connecting MIDI Instruments .................. 28

About MIDI ...................................................... 28

MIDI’s Capability ............................................. 28

Connecting the Digital Piano to a

Computer .................................................. 29

MIDI Functions ..........................................30

MIDI Transmit/Receive Channel Selection .... 30

Local Control ON/OFF .................................... 30

Program Change ON/OFF............................... 31

Control Change ON/OFF ................................ 31

Transmitting Song Data between the

Computer and the Digital Piano............... 32

Loading Song Data from a Computer to the

Digital Piano ..................................................... 32

Transmitting Song Data from the Digital Piano

to a Computer................................................... 33

Backing up Data and Initializing the

Settings .............................................................. 33

Troubleshooting........................................ 34

Options...................................................... 34

Keyboard Stand Assembly ........................35

Index.......................................................... 39

Appendix

Specifications ............................................41

Part Names and Functions

YDP-160/140 Owner’s Manual

Part Names and Functions

POWER

PHONES

[DEMO/SONG]

Listen to the playback of a demo song for each

voice and 50 piano preset songs (page 16).

[METRONOME]

Control the metronome functions (page 24).

[REC]

Record your performance (page 26).

[PLAY]

Play back your recorded performance (page 27).

[MASTER VOLUME]

Adjust the volume level using this control (page 14).

[+]/[–]

These buttons enable you to select a song to play

back from voice demo songs or from “50 Greats

for the Piano.” (pages 16, 17)

They also enable you to change the voice or

tempo. (pages 19, 24)

[PIANO/VOICE]

This button enables you to select any voice from

10 (YDP-160) or 6 (YDP-140) voices. (page 19)

You can also layer two voices (page 22), or select a

type of reverb (page 21).

[PHONES]

A set of standard stereo headphones can be

plugged in here for private practice (page 15).

[POWER](YDP-160)

[STANDBY/ON](YDP-140)

This power switch turns the power to the

unit on or off. (page 14)

Bottom of the keyboard

Part Names and Functions

YDP-160/140 Owner’s Manual

MIDI

INOUT

PEDAL

POWER

[PEDAL]

Connect the pedal cord (page 37).

MIDI [IN/OUT]

Connect a MIDI device to this connector to

use various MIDI functions.

(Connecting MIDI Instruments—page 28)

Shows the MIDI [IN/OUT] and [PEDAL]

jacks as seen when viewed from the rear of

the instrument.

[AC IN] (YDP-160)

Connect the included power cord here.

(page 13)

[DC IN 12V] (YDP-140)

Connect the included power adaptor

here. (page 13)

Pedals

Use these pedals when you want notes

to sustain longer or to sound softer and

round.

(Using the Pedals—page 20)

Bottom of the keyboard

Before Using the Digital Piano

YDP-160/140 Owner’s Manual

Before Using the Digital Piano

Key Cover

To open the key cover:

Lift the cover slightly, then push and slide it

open.

To close the key cover:

Slide the cover toward you and gently lower the

cover over the keys.

CAUTION

Hold the cover with both hands when opening or

closing it. Do not release it until it is fully opened or

closed. Be careful to avoid catching ﬁngers (yours or

others, especially children’s) between the cover and

main unit.

CAUTION

Do not place objects, such as a piece of metal or paper, on top of the key cover. Small objects placed on the key cover

may fall inside the unit when the cover is opened and may be nearly impossible to remove. This could cause electric

shock, short circuit, ﬁre or other serious damage to the instrument.

If this happens, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument

inspected by qualiﬁed Yamaha service personnel.

Music Rest

To raise the music rest:

1. Pull the music rest up and toward yourself as far as it will

go.

2. Flip down the two metal supports at the left and right on

the rear of the music rest.

3. Lower the music rest so that it rests on the metal sup-

ports.

To lower the music rest:

1. Pull the music rest toward yourself as far as it will go.

2. Raise the two metal supports (at the rear of the music

rest).

3. Gently lower the music rest backward until it is all the

way down.

CAUTION

Do not try to use the music rest in a half-raised position.

When lowering the music rest, do not release your hands

from the music rest until it is all the way down.

CAUTION

Be careful to avoid catching your ﬁngers

when opening or closing the cover.

Before Using the Digital Piano

YDP-160/140 Owner’s Manual

Connecting the Power Cord (YDP-160)

Read the instructions below very carefully to make sure that you correctly connect the power cord. YDP-140 users should

skip to the next section “Connecting the Power Adaptor (YDP-140)” for information on connecting the power adaptor.

1. Insert the plug on one end of the power cord to the [AC IN] connector. Refer to the “Part Names and

Functions” on page 11 for information on the location of the [AC IN] connector.

2. Insert the plug on the other end of the power cord to a standard AC outlet.

(The shape of the plug differs depending on locale.)

WARNING

Make sure your digital piano is rated for the AC voltage supplied in the area in which the piano will be used. (The voltage rating appears

on the name plate on the bottom panel). In some areas, a voltage selector may be provided on the bottom panel of the main keyboard

unit near the power cord. Make sure that the voltage selector is set for the voltage in your area. Connecting the unit to an inappropriate

AC supply can seriously damage the internal circuitry and may even pose a shock hazard!

Use only the AC power cord supplied with the instrument. If the supplied power cord is lost or damaged and needs to be replaced, contact

your Yamaha dealer. The use of an inappropriate replacement can pose a ﬁre and shock hazard!

The type of AC power cord provided with the instrument may be different depending on the country in which the instrument was pur-

chased. (In some areas a plug adaptor may be provided to match the pin conﬁguration of the AC wall outlets in your area.)

Do NOT modify the plug provided with the instrument. If the plug will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electri-

cian.

Connecting the Power Adaptor (YDP-140)

Read the instructions below very carefully to make sure that you correctly connect the power adaptor. YDP-160 users

should skip back to the previous section “Connecting the Power Cable (YDP-160)” for information on connecting the

power cord.

1. Make sure that the [STANDBY/ON] switch is set to STANDBY.

2. Connect the DC plug of the power adaptor into the [DC IN 12V] connector. Refer to the “Part Names

and Functions” on page 11 for more information on the location of the [DC IN 12V] connector. Loop

cord slack onto the cord hook so that the plug will not be disconnected accidentally.

3. Insert the AC plug of the power adaptor into a standard AC outlet.

WARNING

Be sure to use a speciﬁed power adaptor. Using a different power adaptor may cause malfunction, overheating, or ﬁre.

WARNING

Do not bend the cord tightly when you hang the cord on the cord hook. Otherwise, a short-circuit or ﬁre may result.

WARNING

Be sure to use an appropriate AC outlet.

CAUTION

If you plan not to use the instrument for a long period of time, or if there is a possibility of lightning, be sure to remove

the power cord plug from the AC outlet.

(Bottom of the

keyboard)

(Bottom of the keyboard)

Cord hook

Adaptor

Before Using the Digital Piano

YDP-160/140 Owner’s Manual

Turning the Power On

Press the [POWER] (YDP-160) or [STANDBY/ON] (YDP-140) switch on the right end of the keyboard to turn on the

power to the unit.

The power indicator located below the left end of the keyboard lights up.

Press the

[POWER] (YDP-160) or [STANDBY/ON] (YDP-140) switch again to turn off the power to the unit.

The power indicator turns off.

Power indicator

If you forget to turn off the power to the piano and close the key cover, the power indicator will remain lit, indicating that

the power is still on.

CAUTION

A small amount of electrical current remains even after the power switch is turned off. If you plan not to use the instru-

ment for a long period of time, be sure to unplug the instrument from the AC outlet.

Setting the Volume

When you start playing, adjust the [MASTER VOLUME] control to the most comfortable listening level.

CAUTION

Do not use this instrument at a high volume level for a long period of time, or your hearing may be damaged.

Power indicator

[POWER] (YDP-160)/

[STANBY/ON] (YDP-140)

The level decreases. The level increases.

Before Using the Digital Piano

YDP-160/140 Owner’s Manual

Using Headphones

Connect a pair of headphones to one of the [PHONES] jacks.

Two [PHONES] jacks are provided.

You can connect two sets of standard stereo headphones. (If you are

using only one pair of headphones, you can plug them into either

jack.)

CAUTION

Do not listen to the instrument at a high volume level through head-

phones for a long period of time, or your hearing may be damaged.

Using the Headphone Hanger (for YDP-160 only)

A headphone hanger is included in the package so that you can hang the head-

phones on this instrument. Install the headphone hanger using the included

two screws (4 × 10mm) as shown in the ﬁgure.

CAUTION

Do not hang anything other than the headphones on the hanger. Otherwise,

this instrument or the hanger may be damaged.

PHONES

Bottom of the keyboard

Standard stereo

phone plug

PHONES

Listening to the Demo Songs

YDP-160/140 Owner’s Manual

Reference

Listening to the Demo Songs

Demo songs are provided that effectively demonstrate each of this instrument’s voices.

Refer to the voice list on

page 19 for more information on

the characteristics of each pre-

set voice.

1. Turn on the power.

While a demo song is playing,

press and hold down the [MET-

RONOME] button and press the

[+] or [–] button to change the

song tempo.

If you are using the metronome

(page 24) during demo song

playback, press the [+] or [–]

button to change the song

tempo.

You can also press keys to

change the tempo. (page 24)

(In case the power is not turned on) Press the [POWER] (YDP-160) or

[STANDBY/ON] (YDP-140) button.

The power to the unit turns on.

Set the

[MASTER VOLUME] control to the half-way point. (You can adjust the

level while playing back a demo song.)

2. Start playing back a demo song.

Press the [DEMO/SONG] button.

The demo songs will not be

transmitted via MIDI.

The demo song for the currently-selected voice starts playing.

3. Select and play a demo song.

You can also change to the next

or previous demo song by

pressing and holding down the

[DEMO/SONG] button and

pressing the [+] or [–] button.

While a demo song is playing, press the [+] or [–] button to select and play the

next or previous demo song.

If you wish to select a particular demo song from 10 (YDP-160) or 6 (YDP-140)

voice demo songs, press and hold down the

[DEMO/SONG] button, then press

one of the C1–A1 (YDP-160) or C1–F1 (YDP-140) keys.

The selected demo song starts to play. Starting with the selected song, the

playback of the demo songs will continue in the following sequence: other

voice demo songs, followed by 50 piano preset songs, and any songs

loaded from the computer. The sequence then returns to the ﬁrst demo

song and repeats until you stop it.

Demo Songs

Each of the 10 (YDP-160) or 6 (YDP-140) voices features its own demo song

that showcases the corresponding voice. Please refer to “Selecting Voices” on

page 19.

The demo songs listed below are re-arranged excerpts from the original compo-

sitions.

tion).

Procedure

C1 A1F1

The lowest key

Key Voice Name Title Composer

C1 GRAND PIANO 1 Sonate für Klavier Nr.13, K.333 W. A. Mozart

E1(YDP-160) HARPSICHORD 1

Concerto a cembalo obbligato, 2 violini, viola e continuo No.7,

BWV.1058

J. S. Bach



1(YDP-140) HARPSICHORD

F1(YDP-160) HARPSICHORD 2 Gigue, Französische Suiten Nr.5, BWV.816 J. S. Bach

G1(YDP-160) CHURCH ORGAN 1

Herr Christ, der ein’ge Gottes-Sohn, BWV.601 J. S. Bach

E1(YDP-140) CHURCH ORGAN



1(YDP-160) CHURCH ORGAN 2 Triosonate Nr.6, BWV.530 J. S. Bach

Listening to 50 Piano Preset Songs

YDP-160/140 Owner’s Manual

Adjusting the Volume

Use the

[MASTER VOLUME] control to adjust the volume.

4. Stop the Voice demo.

Press the [DEMO/SONG] button to stop playback.

Listening to 50 Piano Preset Songs

This digital piano provides performance data for 50 piano songs as well as voice demo songs. You

can simply listen to these songs. You can also refer to the included “50 Greats for the Piano” that

contains scores for 50 piano preset songs.

1. Select and play back a piano preset song.

You can play the keyboard

along with the preset song. You

can change the voice playing on

the keyboard.

The default tempo is automati-

cally selected whenever a new

preset song is selected, and

when a new preset song begins

playback.

While a piano preset song is

playing, hold down the [MET-

RONOME] button and press the

[+] or [–] button to change the

song tempo.

If you are using the metronome

(page 24) during preset song

playback, press the [+] or [–]

button to change the song

tempo.

You can also press keys to

change the tempo. (page 24)

When you select a different

song (or a different song is

selected during chained play-

back), an appropriate reverb

type will be selected accord-

ingly.

The 50 piano preset songs will

not be transmitted via MIDI.

The number of each piano preset song is assigned to the C2–C



6 keys.

While holding down the

[DEMO/SONG] button, press one of the C2–C



6 keys

to select a song to play back.

The selected piano song starts to play.

To play all preset songs consecutively in sequence, while holding down the

[DEMO/SONG] button, press the D6 key.

While a piano preset song is playing, press the

[+] or [–] button to change to the

next or previous piano song.

Adjusting the Volume

Use the

[MASTER VOLUME] control to adjust the volume.

2. Stop playback.

To stop the song during playback (or continuous playback), press the [DEMO/

SONG]

button.

•To continue playing other songs, see procedure

1 above.

Procedure

Song:

On this instrument, perfor-

mance data is called a

“Song.” This includes demo

songs and 50 piano preset

tunes.

C2 C4C3 C5

The highest

key (C7)

Consecutive

playback

(D6)

1st song 10th song 20th song 30th song 40th song 50th song (C



Listening to Songs Loaded from the Computer

YDP-160/140 Owner’s Manual

ENGLISH

Listening to Songs Loaded from the

Computer

You can transfer song data from your computer to this instrument and play back the songs. (See

page 32 for more information on loading song data from the computer.)

1. Select and play back a song.

You can load up to 10 songs or

up to 337 KB of data from the

computer.

Use the following table to write

down the song titles you loaded

from the computer.

Song numbers (1 through 10) are assigned to the D



6–C7 keys (see the illustra-

tion below).

While holding down the [DEMO/SONG] button, press one of the D



6–C7 keys

to select a song to play back.

The selected song starts to play.

While a song is playing, press the

[+] or [–] button to change to the next or pre-

vious song.

Adjusting the Volume

Use the

[MASTER VOLUME] control to adjust the volume while listening to the

song.

2. Stop playback.

To stop the song during playback, press the [DEMO/SONG] button.

Selecting a Song Playback Channel

If a song loaded from the computer uses a voice that is not supported by this

instrument, the originally-assigned voice may not be reproduced accurately. In

this case, switching the song playback channel from “All” to “1 + 2” may

improve the tone to more natural sound.

Selecting 1 + 2 song playback channels:

While pressing and holding down the

[DEMO/SONG] button and the [PIANO/

VOICE]

button simultaneously, press the C7 key.

Channels 1 + 2 will produce the sound.

Selecting all song playback channels:

While pressing and holding down the

[DEMO/SONG] button and the [PIANO/

VOICE]

button simultaneously, press the B6 key.

All channels 1 through 16 will produce the sound.

Procedure

Key Song title



D 6



1st song 10th song

(The highest key)

The highest key

ydp160_m_om_d0.book Page 18 Monday, April 13, 2009 10:53 AM

Selecting & Playing Voices

YDP-160/140 Owner’s Manual

Selecting & Playing Voices

Selecting Voices

To understand the characteris-

tics of various voices, listen to

demo songs for each voice

(page 16).

Press and release the [PIANO/VOICE] button to select the Grand Piano 1 voice.

Press and release the

[PIANO/VOICE] button, press the [+] or [–] button to select a dif-

ferent voice.

Selecting a voice automatically

engages the best-suited reverb

type and depth (page 21) for

that particular voice.

If you wish to select a particular voice directly, press and hold down the [PIANO/

VOICE]

button, then press one of the C1–A1 (YDP-160) or C1–F1 (YDP-140) keys.

Turn the

[MASTER VOLUME] control to adjust the volume level while playing the key-

board.

YDP-160

YDP-140

Procedure

Voice:

On this instrument, a voice

means a “tone” or “tonal

color.”

Key Voice Name Description

C1 Grand Piano 1 Recorded samples from a full concert grand piano. Perfect for classical

compositions as well as any other style that requires acoustic piano.



1Grand Piano 2 Spacious and clear piano with bright reverb. Good for popular music.

D1 E.Piano 1

An electronic piano sound created by FM synthesis. Good for popular music.



1 E.Piano 2 The sound of an electric piano using hammer-struck metallic “tines.” Soft

tone when played lightly, and an aggressive tone when played hard.

E1 Harpsichord 1 The deﬁnitive instrument for baroque music. Since the strings of a harpsi-

chord are plucked, there is no touch response.

F1 Harpsichord 2 Mixes the same voice an octave higher for a more brilliant tone.



1 Vibraphone The sound of a vibraphone played with relatively soft mallets.

G1 Church Organ 1 This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for

sacred music from the Baroque period.



1 Church Organ 2 This is the organ’s full coupler sound, often associated with Bach’s “Toc-

cata and Fugue”.

A1 Strings Spacious and large-scale string ensemble. Try combining this voice with

piano in DUAL mode.

Key Voice Name Description

C1 Grand Piano 1 Recorded samples from a full concert grand piano. Perfect for classical

compositions as well as any other style that requires acoustic piano.



1Grand Piano 2 Spacious and clear piano with bright reverb. Good for popular music.

D1 E.Piano

An electronic piano sound created by FM synthesis. Good for popular music.



1 Harpsichord The deﬁnitive instrument for baroque music. Since the strings of a harpsi-

chord are plucked, there is no touch response.

E1 Church Organ This is a typical pipe organ sound (8 feet + 4 feet + 2 feet). Good for

sacred music from the Baroque period.

F1 Strings Spacious and large-scale string ensemble. Try combining this voice with

piano in DUAL mode.

C1 D1 E1 F1 G1 A1

C 1



D 1



F 1



G 1



The lowest key

Selecting & Playing Voices

YDP-160/140 Owner’s Manual

Using the Pedals

If the damper pedal doesn’t

work, make sure that the pedal

cord is properly plugged into the

main unit (page 37).

Organ and string voices will

continue to sound for as long as

the sostenuto pedal is

depressed.

Damper (Right) Pedal

The damper pedal functions in the same way as a

damper pedal on an acoustic piano. When the

damper pedal is pressed, notes sustain longer.

Releasing the pedal immediately stops (damps) any

sustained notes.

The damper pedal features a half-pedal function.

Sostenuto (Center) Pedal

If you play a note or chord on the keyboard and

press the sostenuto pedal while the note(s) are

held, those notes will sustain as long as you hold

the pedal (as if the damper pedal had been pressed)

but all subsequently played notes will not be sus-

tained. This makes it possible to sustain a chord,

for example, while other notes are played “stac-

cato.”

Soft (Left) Pedal

The soft pedal reduces the volume and slightly changes the timbre of notes played while

the pedal is pressed. The soft pedal will not affect notes that are already playing when it

is pressed.

What is the half-pedal

function?

This function allows the sus-

tain length to vary depend-

ing on how far the pedal is

pressed. The farther you

press the pedal, the more

the sound sustains.

For example, if you press the

damper pedal and all notes

you are playing sound a bit

murky and loud with too

much sustain, you can

release the pedal half way to

subdue the sustain (murki-

ness).

When you press the damper pedal

here, the notes you play before you

release the pedal sustain longer.















When you press the sostenuto pedal

here while holding the note, the note

will sustain as long as you hold the

pedal.















Strona jest ładowana ...

Yamaha Arius YDP-140 Instrukcja obsługi

Marka: Yamaha

Model: Arius YDP-140

Kategoria: Instrumenty muzyczne

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

ściągnij PDF

raport

w innych językach

čeština: Yamaha Arius YDP-140 Návod k obsluze
español: Yamaha Arius YDP-140 El manual del propietario
italiano: Yamaha Arius YDP-140 Manuale del proprietario
Deutsch: Yamaha Arius YDP-140 Bedienungsanleitung
svenska: Yamaha Arius YDP-140 Bruksanvisning
português: Yamaha Arius YDP-140 Manual do proprietário
français: Yamaha Arius YDP-140 Le manuel du propriétaire
Türkçe: Yamaha Arius YDP-140 El kitabı
English: Yamaha Arius YDP-140 Owner's manual
dansk: Yamaha Arius YDP-140 Brugervejledning
русский: Yamaha Arius YDP-140 Инструкция по применению
suomi: Yamaha Arius YDP-140 Omistajan opas
Nederlands: Yamaha Arius YDP-140 de handleiding
română: Yamaha Arius YDP-140 Manualul proprietarului

Yamaha Arius YDP-140 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Yamaha Arius YDP-140 Instrukcja obsługi

w innych językach

Powiązane dokumenty