ALS / ALES
Stand for AL250 / ALE250
Automatic-Feed Soldering Iron
INSTRUCTION MANUAL
Manual ............................. 1 unit
Ref. 0027178
Sponge for Modular
Tool Stands ................... 1 unit
Ref. S7034
Brass Wool .................... 1 unit
Ref. CL6210
Stand for AL250 Automatic-Feed
Soldering Iron ................................... 1 unit
Stand for ALE250 Automatic-Feed
Soldering Iron ................................... 1 unit
Packing List
This manual corresponds to the following references:
AL-SG
works with control unit AL
Included in AL-SG box:
ALE-SA
works with control unit ALU
Included in ALE-SA box:
Included in both, AL-SG and ALE-SA box:
2
Brass Wool
(inside)
Control Unit
Connector
The stand includes a sleep mode that automatically reduces the tip temperature when the tool is in
the stand.
Features and Connections
Wiper for
Modular Tool Stand
Ref. CL7899
Cable Collector
Ref. CC1001
Tip Exchanger
Cartridge Holder
Ajustable Tool Holder
Sponge
www.jbctools.com
3
APS (AP250)
APS (AP250)
APS (AP250)
Assembly
Adjust the tool holder angle to
suit the work position.
Insert the cable into the clip
and then insert into it the cable
collector. Do not leave the cable
longer than necessary to reach
the work area freely.
The cable collector is flexible. It
accompanies and adapts to the
movements during the soldering
process.
The wiper offers different ways to
clean the cartridge tips. If desired
use the included sponge.
Cable Collector and Adjustable Tool Holder
4
AL250-B
0.9-1 Ø0.9-1 Ø0.9-1 Ø
AL250-B
0.9-1 Ø0.9-1 Ø0.9-1 Ø
0.9-1 0.9-1 Ø0.9-1 Ø
AP250
AL250
AL250
SF280
SF250
ALE250
AP250
AL250
AL250
SF280
SF250
ALE250
AP250
AL250
AL250
SF280
SF250
ALE250
Align the cartridge tip with the guide nozzle (6)
and tighten the cartridge screw (7).
Place a new cartridge into the auto-feed iron (4).
Important: For a good connection it is essential
to insert the cartridge till the end, until the mark
(5).
2. Removing1. Unlocking
Loosen the cartridge screw (1) to release the
cartridge (2).
Place the cartridge in the quick tip changer
extractor and pull the tool to remove the
cartridge (3).
3. Inserting
Changing Cartridges
For a safe cartridge change, unplug the tool or turn the station off before following these guidelines.
1
2
Mark
3
4
5
6
7
4. Adjusting
www.jbctools.com
5
AP250
AL250
AL250
SF280
SF250
ALE250
Replacing Guide Sets
Once the tool is disconnected from the control unit and has cooled down, follow these instructions:
Unload the solder wire and disassemble the outlet nozzle (1) from the guide set.
Loosen the guide tube set screw (2), take out the guide set (3) and insert the desired one.
Put the outlet nozzle (1) back on the new cartridge. Leave a gap of 8 to 10 mm (0.31 to 0.39 in)
between the cartridge tip and the outlet nozzle (4).
Once the guide nozzle length is adjusted tighten the guide set screw (2).
Outlet Nozzle Guide Nozzle
8 -10 m m
0.31-0.40 in
1
2
3
4
Guide Tube
Set Screw
Guide Set
Tap gently to remove excess
solder.
Use the slots to remove the
remaining particles.
Wiper
Tapping Wiping Sponge
The softest cleaning method.
Keep the sponge damp with
distilled water when working to
avoid tip wear.
The integrated wiper offers different ways to clean the cartridge tips.
6
AP250
AL250
AL250
SF280
SF250
ALE250
Replacing Guide Sets
Once the tool is disconnected from the control unit and has cooled down, follow these instructions:
Unload the solder wire and disassemble the outlet nozzle (1) from the guide set.
Loosen the guide tube set screw (2), take out the guide set (3) and insert the desired one.
Put the outlet nozzle (1) back on the new cartridge. Leave a gap of 8 to 10 mm (0.31 to 0.39 in)
between the cartridge tip and the outlet nozzle (4).
Once the guide nozzle length is adjusted tighten the guide set screw (2).
Outlet Nozzle Guide Nozzle
8 -10 m m
0.31-0.40 in
1
2
3
4
Guide Tube
Set Screw
Guide Set
Wiper and Brass Wool Replacement
Lift the wiper at its front edge.
The wiper and brass wool can easily be removed for cleaning or replacement when they are worn.
Remove the wiper by pulling
it out.
Replace the brass wool with a
new one when it is worn out.
Place the wiper back o replace
them if desired.
Maintenance
Before carrying out maintenance or storage, always unplug the stand from the station and the tool.
- Use a damp cloth to clean the stand. Alcohol can be used only when cleaning metal parts.
- Check periodically that the metal parts of the tool/stand are clean so that the station can check the
tool’s status.
- Periodically check all cables and tube connections.
- Replace any defective or damaged parts. Use original JBC spare parts only. Repairs should only be
performed by a JBC authorized technical service.
Clean periodically Clean periodically
www.jbctools.com
7
Safety
- Do not use the stand for any purpose other than soldering or rework.
- The power cord must be plugged into approved bases. Be sure that it is properly grounded
before use. When unplugging it, hold the plug, not the wire.
- The tool should be placed in the stand when not in use in order to activate the sleep mode.
The soldering tip, the metal part of the tool and the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.
- Avoid the contact of flux with skin or eyes to prevent irritation.
- Be careful with the fumes produced when soldering.
- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when
working to avoid personal harm.
- Utmost care must be taken with liquid tin waste which can cause burns.
- This appliance can be used by children over the age of eight and also persons with reduced physical,
sensory or mental capabilities or lack of experience provided that they have been given adequate
supervision or instruction concerning the use of the appliance and understand the hazards involved.
Children must not play with the appliance.
- Maintenance must not be carried out by children unless supervised.
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
8
Notes
www.jbctools.com
9
Notes
10
ALS
Stand for AL250 Automatic-Feed Soldering Iron
Ref.: AL-SG
ALES
Stand for ALE250 Automatic-Feed Soldering Iron
Ref.: ALE-SA
For both references:
- Includes Sleep function
- Total Net Weight 1946 g / 4.29 lb
- Package Dimensions / Weight: 342 x 155 x 120 mm / 1476 g
(L x W x H) 13.46 x 6.10 x 4.72 in / 3.25 lb
Complies with CE standards.
ESD safe.
Specifications
www.jbctools.com
11
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must
be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
40 mm
50 mm
60 mm
80 mm
100 mm
130 mm 130 mm
para manuales - color gris
200 mm
300 mm
0027178-200223
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
