Sony KDL-40W4000 Instrukcja obsługi

LCD Digital Colour TV

Printed in Spain

3-298-243-43(1)

K

For useful information about Sony products

Для получения полезной информации о продукции Сони

Szczegółowe informacje o produktach Sony

Užitečné informace o výrobcích Sony

Pre viac informácií o produktoch Sony

Sony termékekről hasznos információkat találhat az alábbi

weboldalon

GB

RU

K

PL

CZ

SK

HU

KDL-52W40xx

KDL-52W42xx

KDL-46W40xx

KDL-46W42xx

KDL-40W40xx

KDL-40W42xx

KDL-32W40xx

KDL-32W42xx

KDL-40E40xx

KDL-32E40xx

KDL-26E40xx

KDL-37V45xx

KDL-37V47xx

KDL-32V45xx

KDL-32V47xx

KDL-26V45xx

KDL-26V47xx

LCD Digital Colour TV

Operating Instructions

Инструкция по эксплуатации

Instrukcja obsługi

Návod k použití

Návod na obsluhu

Kezelési utasítás

000COV_10,4mm(431).indd 1000COV_10,4mm(431).indd 1 07/08/2008 18:43:1507/08/2008 18:43:15

2

GB

Thank you for choosing this Sony product.

Before operating the TV, please read this manual

thoroughly and retain it for future reference.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product

shall not be treated as household waste.

Instead it shall be handed over to the applicable collection

point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of

correctly, you will help prevent potential negative

consequences for the environment and human health,

which could otherwise be caused by inappropriate waste

handling of this product. The recycling of materials will

help to conserve natural resources. For more detailed

information about recycling of this product, please contact

your local Civic Office, your household waste disposal

service or the shop where you purchased the product.

Disposal of waste batteries

(applicable in the European Union

and other European countries with

separate collection systems)

This symbol on the battery or on the

packaging indicates that the battery

provided with this product shall not be

treated as household waste. By ensuring

these batteries are disposed of correctly,

you will help prevent potentially negative consequences

for the environment and human health which could

otherwise be caused by inappropriate waste handling of the

battery. The recycling of the materials will help to conserve

natural resources. In case of products that for safety,

performance or data integrity reasons require a permanent

connection with an incorporated battery, this battery should

be replaced by qualified service staff only. To ensure that

the battery will be treated properly, hand over the product

at end-of-life to the applicable collection point for the

recycling of electrical and electronic equipment. For all

other batteries, please view the section on how to remove

the battery from the product safely. Hand the battery over

to the applicable collection point for the recycling of waste

batteries. For more detailed information about recycling of

this product or battery, please contact your local Civic

Office, your household waste disposal service or the shop

where you purchased the product.

The manufacturer of this product is Sony

Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-

0075 Japan. The Authorized Representative for EMC

and product safety is Sony Deutschland GmbH,

Hedelfinger Strasse 61, 70327 Stuttgart, Germany.

For any service or guarantee matters please refer to

the addresses given in separate service or guarantee

documents.

• Any functions related to Digital TV ( ) will only

work in countries or areas where DVB-T (MPEG2 and

MPEG4 AVC) digital terrestrial signals are broadcast or

where you have access to a compatible DVB-C (MPEG2

and MPEG4 AVC) cable service. Please confirm with

your local dealer if you can receive a DVB-T signal

where you live or ask your cable provider if their DVB-

C cable service is suitable for integrated operation with

this TV.

• The cable provider may charge an additional fee for such

a service and you may be required to agree to their terms

and conditions of business.

• Although this TV set follows DVB-T and DVB-C

specifications, compatibility with future DVB-T digital

terrestrial and DVB-C digital cable broadcasts cannot be

guaranteed.

• Some Digital TV functions may not be available in some

countries/regions and DVB-C cable may not operate

correctly with all providers.

• For more information about DVB-C functionality please

see our cable support site:

http://support.sony-europe.com/TV/DVBC

/

• is a registered trademark of the DVB Project

• Manufactured under license from BBE Sound, Inc.

Licensed by BBE Sound, Inc. under one or more of the

following US patents: 5510752, 5736897. BBE and

BBE symbol are registered trademarks of BBE Sound,

Inc.

• Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks

of Dolby Laboratories.

• HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

~

• The illustrations used in this manual are of the

KDL-40W4000 unless otherwise state.

• The "x" that appear on the model name, correspond to

numeric digits related to colour variation.

Introduction

Disposal of the TV set

Notice for Digital TV function

Trademark information

HD3D Sound

ViV

A

010COV.book Page 2 Thursday, September 25, 2008 4:59 PM

3

GB

Table of Contents

Start-up Guide 4Checking the accessories.................................................................................................... 4

Safety information................................................................................................................ 9

Precautions........................................................................................................................ 10

Overview of the remote ................................................................................................... 11

Overview of the TV buttons and indicators................................................................... 12

Watching TV.......................................................................................................................13

Checking the Guide .................................................................................................. 15

Using the Digital Favourite list .................................................................................. 16

Connecting optional equipment.......................................................................................... 17

Viewing pictures from connected equipment .....................................................................18

Using BRAVIA Sync (Control for HDMI) ............................................................................19

Overview of the TV Home Menu (XMB™)......................................................................... 21

Settings.............................................................................................................................. 22

Instruction Manual ........................................................................................................ 22

Picture .......................................................................................................................... 22

Sound ...........................................................................................................................23

Features .......................................................................................................................24

Set-up ...........................................................................................................................26

Analogue Set-up .......................................................................................................... 28

Digital Set-up ....................................................................................................... 30

Photo .................................................................................................................................32

Picture Frame ............................................................................................................... 32

USB Photo Viewer ....................................................................................................... 32

Specifications..................................................................................................................... 33

Troubleshooting .................................................................................................................36

Start-up Guide 4

Watching TV

Using Optional Equipment

Using MENU Functions

Additional Information

: for digital channels only

GB

Before operating the TV, please read the “Safety information” section of this manual.

Retain this manual for future reference.

010COV.book Page 3 Thursday, September 25, 2008 4:59 PM

4

GB

Start-up Guide

1: Checking the

accessories

Mains lead (1) (only for KDL-52W4xxx, KDL-

46W4xxx, KDL-40W4xxx, KDL-40E4xxx)

Remote RM-ED011 (1)

Remote RM-ED011 W (1) (only for KDL-

40E4xxx, KDL-32E4xxx, KDL-26E4xxx)

Size AA batteries (R6 type) (2)

Stand (1) (except for KDL-52W4xxx,

KDL-26E4xxx)

Screws for stand (4) (only for KDL-

46W4xxx, KDL-40W4xxx, KDL-40E4xxx,

KDL-37V4xxx)

Screws for stand (3) (only for KDL-

32W4xxx, KDL-32E4xxx, KDL-32V4xxx,

KDL-26V4xxx)

To insert batteries into the remote

2: Attaching the stand

(except for KDL-52W4xxx,

KDL-26E4xxx)

1 Open the carton box and take out the stand

and the screws.

Push and lift the cover to open.

010COV.book Page 4 Thursday, September 25, 2008 4:59 PM

5

GB

Start-up Guide

2 Place the TV set on the stand. Take care not to

interfere with cables.

3 Fix the stand to the TV using the supplied

screws.

~

If using an electric screwdriver, set the tightening torque at

approximately 1.5 N·m (15 kgf·cm)

3: Connecting an

aerial/VCR/ DVD

recorder

KDL-46W4xxx

KDL-40W4xxx

KDL-40E4xxx

KDL-37V4xxx

KDL-32W4xxx

KDL-32E4xxx

KDL-32V4xxx

KDL-26V4xxx

C

onnecting an aerial/cable

Connecting an aerial/ cable/ VCR/ DVD recorder

Coaxial cable

Scart lead

VCR/ DVD recorder

Coaxial cable

Terrestrial signal

or cable

Terrestrial signal

or cable

010COV.book Page 5 Thursday, September 25, 2008 4:59 PM

6

GB

4: Preventing the TV

from toppling over

1 Install a wood screw (4 mm in diameter, not

supplied) in the TV stand.

2 Install a machine screw (M6 x 12, not

supplied) into the screw hole of the TV.

3 Tie the wood screw and the machine screw

with a strong cord.

5: Connecting the cables

6: Bundling the cables

7:

Performing the initial

set-up

1 Connect the TV to your mains socket

(220-240V AC, 50Hz).

2 Press 1 on the TV.

When you switch on the TV for the first time, the

Language menu appears on the screen.

3 Press F/f/G/g to select the language

displayed on the menu screens, then press .

KDL-52W4xxx

KDL-46W4xxx

KDL-40W4xxx

KDL-40E4xxx

3,4,5

GUIDE

Česky

Magyar

Русский

ББ

лгар

ски

Suomi

Dansk

Svenska

Norsk

Slovenčina

Română

English

Nederlands

Français

Italiano

Deutsch

Türkçe

Español

Català

Português

Polski

Language

Back

Set

Analogue

010COV.book Page 6 Thursday, September 25, 2008 4:59 PM

7

GB

Start-up Guide

4

Press

F

/

f

to select the country/region in

which you will operate the TV, then press .

If the country/region in which you want to use

the TV does not appear in the list, select “-”

instead of a country/region.

5 Press F/f to select the location type in which

you will operate the TV, then press .

~

Sony recommends you to select “Home” for power saving.

This option selects the initial picture mode

appropriate for the typical lighting condition in

these enviroments.

8: Auto-tuning the TV

1 Select OK then press .

2 Press F/f to select “Antenna” or “Cable”,

then press .

If you select “Cable”, the screen for selecting the

scan type appears. See “To tune the TV for

Cable connection” (page 8).

The TV starts searching for all available digital

channels, followed by all available analogue

channels. This may take some time, so do not

press any buttons on the TV or remote while

proceeding.

If a message appears for you to confirm the

aerial connection

No digital or analogue channels were found.

Check all the aerial/cable connection and then

press to start auto-tuning again.

3 When the Programme Sorting menu appears

on the screen, follow the steps of

“Programme Sorting”(page 28).

If you do not change the order in which the

analogue channels are stored on the TV, press

RETURN to go to step 4.

4

For details, see page 24.

5

For details, see page 19.

6 Press .

The TV has now tuned in all the available

channels.

~

When a digital broadcast channel cannot be received, or

when selecting a region in which there are no digital

broadcasts, the time must be set after performing step 3.

Back

Set

Analogue

United Kingdom

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

-

Country

Select country

Back

Set

Analogue

Location

Home

Shop

Select location

Back

Set

Analogue

Auto Tuning

OK Cancel

Do you want to start Auto Tuning?

Back

Set

Analogue

Quick Start

Yes No

Do you want to enable Quick Start?

TV turns on more quickly but standby power

consumption is increased.

Back

Set

Analogue

Control for HDMI

Yes No

Do you want to enable control for compatible

HDMI devices?

010COV.book Page 7 Thursday, September 25, 2008 4:59 PM

8

GB

To tune the TV for Cable connection

1 Press .

2 Press F/f to select “Quick Scan” or “Full

Scan”, then press .

"Quick Scan" : channels are tuned according to

the cable operator information within the

broadcast signal.

Recommended setting for "Frequency",

"Network ID" and "Symbol Rate" is "Auto".

This option is recommended for fast tuning

when supported by your cable operator.

If the "Quick Scan" does not tune, please use the

"Full Scan" method below.

"Full Scan" : All available channels are tuned

and stored. This procedure may take some time.

This option is recommended when "Quick Scan"

is not supported by your cable provider.

For further information about supported cable

providers, refer to support web site:

http://support.sony-europe.com/TV/DVBC/

3 Press f to select “Start”, then press .

The TV starts searching for channels. Do not

press any buttons on the TV or remote.

~

Some cable providers do not support “Quick Scan”. If no

channels are detected using “Quick Scan”, perform “Full

Scan”.

Detaching the Table-

Top Stand from the TV

~

Do not remove the Table-Top Stand for any reason other

than to wall-mount the TV.

KDL-32W4xxx

KDL-32E4xxx

KDL-32V4xxx

KDL-26V4xxx

KDL-52W4xxx

KDL-46W4xxx

KDL-40W4xxx

KDL-40E4xxx

KDL-37V4xxx

KDL-26E4xxx

010COV.book Page 8 Thursday, September 25, 2008 4:59 PM

9

GB

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below

in order to avoid any risk of fire, electrical shock or damage and/or

injuries.

Installation

s The TV set should be installed near an easily accessible mains

socket.

s Place the TV set on a stable, level surface.

s Only qualified service personnel should carry out wall

installations.

s For safety reasons, it is strongly recommended that you use

Sony accessories, including:

- KDL-52W40xx/ KDL-52W42xx/ KDL-46W40xx/

KDL-46W42xx/ KDL-40W40xx/ KDL-40W42xx/

KDL-32W40xx/ KDL-32W42xx/ KDL-40E40xx/

KDL-32E40xx/ KDL-37V45xx/ KDL-37V47xx/

KDL-32V45xx/ KDL-32V47xx:

Wall-Mount Bracket SU-WL500.

- KDL-26V45xx/ KDL-26V47xx/ KDL-26E40xx:

Wall-mount Bracket SU-WL100.

- KDL-46W40xx/ KDL-46W42xx/ KDL-40W40xx/

KDL-40W42xx/KDL-32W40xx/ KDL-32W42xx/

KDL-40E40xx/ KDL-32E40xx/ KDL-37V45xx/

KDL-37V47xx/ KDL-32V45xx/ KDL-32V47xx:

TV stand SU-FL300M.

s Be sure to use the screws supplied with the Wall-mount bracket

when attaching the mounting hooks to the TV set. The supplied

screws are designed so that they are 8 mm to 12 mm in length

when measured from the attaching surface of the mounting

hook.

The diameter and length of the screws differ depending on the

Wall-mount bracket model.

Use of screws other than those supplied may result in internal

damage to the TV set or cause it to fall, etc.

Transporting

s Before transporting the TV set,

disconnect all cables.

s Two or three people are needed

to transport a large TV set.

s When transporting the TV set

by hand, hold it as shown on

the right. Do not put stress on

the LCD panel.

s When lifting or moving the TV

set, hold it firmly from the

bottom.

s When transporting the TV set,

do not subject it to jolts or

excessive vibration.

s When transporting the TV set

for repair or when moving,

pack it using the original

carton and packing material.

Ventilation

s Never cover the ventilation holes or insert anything in the

cabinet.

s Leave space around the TV set as shown below.

s It is strongly recommended that you use a Sony wall-mount

bracket in order to provide adequate air-circulation.

Installed on the wall

Installed with stand

s To ensure proper ventilation and prevent the collection of dirt

or dust:

– Do not lay the TV set flat, install upside down, backwards,

or sideways.

– Do not place the TV set on a shelf, rug, bed or in a closet.

– Do not cover the TV set with a cloth, such as curtains, or

items such as newspapers, etc.

– Do not install the TV set as shown below.

Mains lead

Handle the mains lead and socket as follows in order to avoid any

risk of fire, electrical shock or damage and/or injuries:

– Use only mains leads supplied by Sony, not other suppliers.

– Insert the plug fully into the mains socket.

– Operate the TV set on a 220–240 V AC supply only.

– When wiring cables, be sure to unplug the mains lead for your

safety and take care not to catch your feet on the cables.

– Disconnect the mains lead from the mains socket before

working on or moving the TV set.

– Keep the mains lead away from heat sources.

– Unplug the mains plug and clean it regularly. If the plug is

covered with dust and it picks up moisture, its insulation may

deteriorate, which could result in a fire.

Mounting Hook

Hook attachment on rear of TV set

Screw (supplied with the Wall-mount

bracket)

8 mm - 12 mm

Be sure to hold the bottom of

the panel, not the front part.

Do not handle with dent

area.

Do not handle with the

transparent bottom part.

30 cm

10 cm

Leave at least this space around the set.

30 cm

10 cm 10 cm

6 cm

Leave at least this space around the set.

Air circulation is blocked.

Wall Wall

Continued

010COV.book Page 9 Thursday, September 25, 2008 4:59 PM

10

GB

Notes

s Do not use the supplied mains lead on any other equipment.

s Do not pinch, bend, or twist the mains lead excessively. The

core conductors may be exposed or broken.

s Do not modify the mains lead.

s Do not put anything heavy on the mains lead.

s Do not pull on the mains lead itself when disconnecting the

mains lead.

s Do not connect too many appliances to the same mains socket.

s Do not use a poor fitting mains socket.

Prohibited Usage

Do not install/use the TV set in locations, environments or

situations such as those listed below, or the TV set may malfunction

and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other

vessel, inside a vehicle, in medical institutions, unstable locations,

near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may

enter; where it might be exposed to mechanical vibration, near

flammable objects (candles, etc). The TV set shall not be exposed

to dripping or splashing and no objects filled with liquids, such as

vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or

with attachments not recommended by the manufacturer.

Disconnect the TV set from mains socket and aerial during

lightning storms.

Broken pieces:

s Do not throw anything at the TV set. The screen glass may

break by the impact and cause serious injury.

s If the surface of the TV set cracks, do not touch it until you have

unplugged the mains lead. Otherwise electric shock may result.

When not in use

s If you will not be using the TV set for several days, the TV set

should be disconnected from the mains for environmental and

safety reasons.

s As the TV set is not disconnected from the mains when the TV

set is just turned off, pull the plug from the mains to disconnect

the TV set completely.

s However, some TV sets may have features that require the TV

set to be left in standby to work correctly.

For children

s Do not allow children to climb on the TV set.

s Keep small accessories out of the reach of children, so that they

are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the mains lead immediately if any

of the following problems occur.

Ask your dealer or Sony service centre to have it checked by

qualified service personnel.

When:

– Mains lead is damaged.

– Poor fitting of mains socket.

– TV set is damaged by being dropped, hit or having something

thrown at it.

– Any liquid or solid object falls through openings in the cabinet.

Precautions

Viewing the TV

s View the TV in moderate light, as viewing the TV in poor light

or during long period of time, strains your eyes.

s When using headphones, adjust the volume so as to avoid

excessive levels, as hearing damage may result.

LCD Screen

s Although the LCD screen is made with high-precision

technology and 99.99% or more of the pixels are effective,

black dots may appear or bright points of light (red, blue, or

green) may appear constantly on the LCD screen. This is a

structural property of the LCD screen and is not a malfunction.

s Do not push or scratch the front filter, or place objects on top of

this TV set. The image may be uneven or the LCD screen may

be damaged.

s If this TV set is used in a cold place, a smear may occur in the

picture or the picture may become dark. This does not indicate

a failure. These phenomena disappear as the temperature rises.

s Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

s The screen and cabinet get warm when this TV set is in use.

This is not a malfunction.

s The LCD screen contains a small amount of liquid crystal.

Some fluorescent tubes used in this TV set also contain

mercury. Follow your local ordinances and regulations for

disposal.

Handling and cleaning the screen surface/

cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from

mains socket before cleaning.

To avoid material degradation or screen coating degradation,

observe the following precautions.

s To remove dust from the screen surface/cabinet, wipe gently

with a soft cloth. If dust is persistent, wipe with a soft cloth

slightly moistened with a diluted mild detergent solution.

s Never use any type of abrasive pad, alkaline/acid cleaner,

scouring powder, or volatile solvent, such as alcohol, benzene,

thinner or insecticide. Using such materials or maintaining

prolonged contact with rubber or vinyl materials may result in

damage to the screen surface and cabinet material.

s When adjusting the angle of the TV set, move it slowly so as to

prevent the TV set from moving or slipping off from its table

stand.

Optional Equipment

Keep optional components or any equipment emitting

electromagnetic radiation away from the TV set. Otherwise picture

distortion and/or noisy sound may occur.

Batteries

s Observe the correct polarity when inserting batteries.

s Do not use different types of batteries together or mix old and

new batteries.

s Dispose of batteries in an environmentally friendly way.

Certain regions may regulate the disposal of batteries. Please

consult your local authority.

s Handle the remote with care. Do not drop or step on it, or spill

liquid of any kind onto it.

s Do not place the remote in a location near a heat source, a place

subject to direct sunlight, or a damp room.

010COV.book Page 10 Thursday, September 25, 2008 4:59 PM

11

GB

Overview of the remote

1 "/1 – TV standby

Turns the TV on and off from standby mode.

2 AUDIO

In analogue mode: Press to change the dual sound mode (page 24).

In digital mode: Press to select the audio language (page 30).

3 – Subtitles

Press to display the subtitles on current program if TV channels broadcast

such information (in digital mode only) (page 30).

4 / – Input select / Text hold

• In TV mode: Selects the input source from equipment connected to the TV

sockets (page 18).

• In Text mode (page 14): Holds the current page.

5 F/f/G/g/

6 OPTIONS (page 14, 19)

Enables you to access various viewing options and change/make adjustments

according to the source and screen format.

7 HOME (page 21)

Displays the TV Home menu.

8 Coloured buttons (page 14, 15, 16)

9 Number buttons

• In TV mode: Selects channels. For channel numbers 10 and above, enter the

second and third digit quickly.

• In Text mode: Enters the three digit page number to select the page.

0 – Favourite (page 16)

qa PROG +/–//

• In TV mode: Selects the next (+) or previous (-) channel.

• In Text mode (page 14): Selects the next ( ) or previous ( ) page.

qs – Previous channel

Returns to the previous channel watched (for more than five seconds).

qd % – Mute the sound

qf 2 +/– – Volume

qg / – Text (page 14)

qh – RETURN

Returns to the previous screen of any displayed menu.

qj – GUIDE (page 15)

qk ANALOG – Analogue mode (page 13)

ql DIGITAL – Digital mode (page 13)

w; BRAVIA Sync (page 19)

wa – Screen mode (page 14)

ws / – Info / Text reveal

• In digital mode: Displays details of the programme currently being watched.

• In analogue mode: Each time you press

/ , the information on the

screen changes as follows: Displays information such as current channel

number and screen format

t Time is displayed t Information is hidden.

• In Text mode (page 14): Reveals hidden information (e.g. answers to a

quiz).

z

The number 5, PROG +, AUDIO and buttons have tactile dots. Use the

tactile dots as references when operating the TV.

GUIDE

010COV.book Page 11 Thursday, September 25, 2008 4:59 PM

12

GB

Overview of the TV buttons and indicators

1 (page 21)

2 / – Input select / OK

• In TV mode: Selects the input source from

equipment connected to the TV sockets

(page 18).

• In TV menu: Selects the menu or option, and

confirms the setting.

3 2 +/–//

• In TV mode: Increases (+) or decreases (-) the

volume.

• In TV menu: Moves through the options right

( ) or left ( ).

4 PROG +/–//

• In TV mode: Selects the next (+) or previous (-)

channel.

• In TV menu: Moves through the options up ( )

or down ( ).

5 1 – Power

Turns the TV on or off.

~

To disconnect the TV completely, pull the plug

from the mains.

6 Light Sensor

Do not put anything over the sensor, as its function

may be affected.

7 Remote control sensor

• Receives IR signals from the remote.

• Do not put anything over the sensor, as its

function may be affected.

8 – Picture Off / Timer indicator

• Lights up in green when the picture is switched

off (page 24).

• Lights up in orange when the timer is set

(page 25).

9 1 – Standby indicator

Lights up in red when the TV is in standby mode.

0 " – Power / Timer REC programme indicator

• Lights up in green when the TV is turned on.

• Lights up in orange when the timer recording is

set (page 15).

• Lights up in red during the timer recording.

~

• Make sure that the TV is completely turned off

before unplugging the mains lead. Unplugging the

mains lead while the TV is turned on may cause the

indicator to remain lit or may cause the TV to

malfunction.

• Do not put anything over the indicators as their

functions may be affected.

HOME

(only for KDL-40E4xxx, KDL-32E4xxx,

KDL-26E4xxx)

HOME

010COV.book Page 12 Thursday, September 25, 2008 4:59 PM

13

GB

Watching TV

1 Press 1 on the TV to switch on the TV.

When the TV is in standby mode (the 1

(standby) indicator on the TV (front) is red),

press "/1 on the remote to switch on the TV.

2 Press DIGITAL to switch to digital mode or

ANALOG to switch to analogue mode.

The channels available vary depending on the

mode.

3 Press the number buttons or PROG +/- to

select a TV channel.

To select channel numbers 10 and above using

the number buttons, enter the second and third

digits within two seconds.

To select a digital channel using the Guide, see

page 15.

In digital mode

An information banner appears briefly. The

following icons may be indicated on the banner.

Additional operations

Watching TV

3

2

3

GUIDE

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

: Recommended minimum age for current

programme (from 4 to 18 years)

: Parental Lock

c: Current programme is being recorded

To Do this

Turn on the TV

from Standby mode

without sound

Press %. Press 2 +/- to set the

volume level.

Adjust the volume Press 2 + (increase)/

- (decrease).

010COV.book Page 13 Thursday, September 25, 2008 4:59 PM

14

GB

To access Text

Press /. Each time you press /, the display

changes cyclically as follows:

Text t Text over the TV picture (mix mode) t No

Text (exit the Text service)

To select a page, press the number buttons or

PROG +/-.

To hold a page, press / .

To reveal hidden information, press / .

z

When four coloured items appear at the bottom of the Text

page, Fastext is available. Fastext allows you to access

pages quickly and easily. Press the corresponding coloured

button to access the page.

To change the screen format manually to

suit the broadcast

Press repeatedly to select the desired screen

format.

* Parts of the top and bottom of the picture may be cut off.

~

Some characters and/or letters at the top and the bottom of

the picture may not be visible in Smart mode. In such a

case, you can select “Vertical Size” using the “Screen

Settings” (page 26) menu and adjust vertical size to make

it visible.

z

• When “Auto Format” is set to “On”, the TV will

automatically select the best mode to suit the broadcast

(page 26).

• You can adjust the position of the picture when selecting

“Smart”, “14:9” or “Zoom”. Press

F/f to move up or

down (e.g. to read subtitles).

Using the Options menu

Press OPTIONS to display the following options

when viewing a TV programme.

Smart*

Displays conventional

4:3 broadcasts with an

imitation wide screen

effect. The 4:3 picture

is stretched to fill the

screen.

4:3

Displays conventional

4:3 broadcasts (e.g.

non-wide screen TV) in

the correct proportions.

Wide

Displays wide screen

(16:9) broadcasts in the

correct proportions.

Zoom*

Displays cinemascopic

(letter box format)

broadcasts in the

correct proportions.

14:9*

Displays 14:9

broadcasts in the

correct proportions. As

a result, black border

areas are visible on the

screen.

Options Description

Picture Mode See page 22.

Sound Effect See page 23.

Speaker See page 27.

Subtitle Setting (in

digital mode only)

See page 30.

Sleep Timer See page 25.

Power Saving See page 24.

System Information (in

digital mode only)

See page 31.

010COV.book Page 14 Thursday, September 25, 2008 4:59 PM

15

GB

Watching TV

Checking the Guide *

1 In digital mode, press GUIDE.

2 Perform the desired operation as shown in the

following table or displayed on the screen.

* This function may not be available in some countries/regions.

Back

001 BBC ONE

002 BBC TWO

003 ITV1

004 Channel 4

005 Five

006 ITV2

007 BBC THREE

008 BBC FOUR

009 ITV3

010 SKY THREE

Category30 min ViewNextPrevious

Homes Under the Hammer Neighbours Afterlife

Ready Steady Cook Extraordinary People: Britains Iden... CSI: Crime Scene Inv...

Dancing On Ice Exclusive Cracker

Sign Zone: Ancient Rome: The Rise a... The Jeremy Kyle... Homes Under th...

House Law and Order: Special Victims U... PartyPoker.com Worl...

Crime Hour: Midsomer Murders Vodafone TBA: L...

BBC Learning Zone: Schools: World P... A Picture of Brit... Eastenders

ER Real Crime: The Truth About the... This is BBC FOUR

Past Everybody Loves Raymond The Sharon Osb...

Racing from Chepstow and Ascot Baseball Wedne... Trans World Sport

Select +/- 1 day on/off Event InformationTun e

To day

13: 0012: 3012: 0011: 30

All Categories

Fri 16 Mar 11:35

To Do this

Watch a programme Press F/f/G/g to select the programme, then press .

Turn off the Guide Press

GUIDE.

Sort the programme information by

category

– Category list

1 Press the blue button.

2 Press

F/f to select a category, then press .

Set a programme to be recorded

– Timer REC

1 Press F/f/G/g to select the future programme you want to record,

then press

/ .

2 Press

F/f to select “Timer REC”.

3 Press to set the TV and your VCR/DVD recorder timers.

A c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

z

To record the programme you are currently watching, press / .

Set a programme to be displayed

automatically on the screen when it

starts

– Reminder

1 Press F/f/G/g to select the future programme you want to

display, then press

/ .

2 Press

F/f to select “Reminder”, then press .

A c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

~

If you switch the TV to standby mode, it will automatically turn itself on

when the programme is about to start.

Set the time and date of a programme

you want to record

– Manual timer REC

1 Press F/f/G/g to select the future programme you want to record,

then press

/ .

2 Press

F/f to select “Manual timer REC”, then press .

3 Press

F/f to select the date, then press g.

4 Set the start and stop time in the same way as in step 3.

5 Press

F/f to select the programme, then press .

6 Press to set the TV and your VCR/ DVD recorder timers.

A c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

z

To record the programme you are currently watching, press / .

Continued

010COV.book Page 15 Thursday, September 25, 2008 4:59 PM

16

GB

~

• You can set the timer record function on the TV to automatically operate the recorder only when the connected recorder is

compatible with SmartLink. However, this feature may not operate with certain types of recorder, even though it is stated

that the recorder is SmartLink compatible. For details please refer to the instruction manual supplied with your recorder.

• Once a recording has begun, you can switch the TV to standby mode, but do not turn off the TV completely or the recording

may be cancelled.

• If an age restriction for programmes has been selected, a message asking for a PIN Code will appear on the screen. For

details, see “Parental Lock” (page 31).

Using the Digital Favourite list *

1 In digital mode, press .

2 Perform the desired operation as shown in the

following table or displayed on the screen.

* This function may not be available in some countries/regions.

Cancel a recording/reminder

– Timer list

1 Press / .

2 Press

F/f to select “Timer list”, then press .

3 Press

F/f to select the programme you want to cancel, then press

.

4 Press

F/f to select “Cancel Timer”, then press .

A display appears to confirm that you want to cancel the programme.

5 Press G/g to select “Yes”, then press to confirm.

To Do this

Digital Favourite list

Back

Store Favourite

Digital

Favourite Set-up

Favourites 1

001 BBC ONE

002 BBC TWO

003 ITV1

004 Channel 4

005 Five

006 BBC Three

007 ITV2

008 Sky Sports

009 UKTV History

010 Channel 4+1

011 More 4

012 abc1

013 QVC

014 UKTV Gold

015 The HITS

016 UKTV Bright Ideas

017 ftn

018 TMF

019 E4

020 E4+1

Favourites 2NextPrevious

Enter Programme Number: - - -

To Do this

Create your Favourite list for the first

time

1 Press F/f/G/g to select the channel you want to add, then press

.

Channels that are stored in the Favourite list are indicated by a

symbol.

2 Press yellow key to select “Favourites 2” or “Favourites 3”.

Watch a channel

1 Press yellow key to navigate through favourite lists.

2 Press

F/f to select the channel, then press .

Turn off the Favourite list

Press RETURN.

Add or remove channels in the currently

edited Favourite list

1 Press the blue button.

2 Press the yellow button to choose the list you want to edit.

3 Press

F/f/G/g to select the channel you want to add or remove,

then press .

Remove all channels from the current

Favourite list

1 Press the blue button.

2 Press the yellow button to select the favourite list you want to edit.

3 Press the blue button.

4 Press

G/g to select “Yes”, then press to confirm.

010COV.book Page 16 Thursday, September 25, 2008 4:59 PM

17

GB

Using Optional Equipment

Connecting optional equipment

You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.

Using Optional Equipment

,

For service

use only

DVC camcorder

Headphones

DVD recorder

Decoder

VCR

Video game

equipment

DVD player

Decoder

PC

PC (HDMI output)

Blu-ray disc player

Digital video camera

Audio system

PC (HDMI output)

Blu-ray disc player

Digital video camera

DVD player

CAM card

USB

Hi-Fi audio

equipment

Digital decoder

DVD player with

component output

Hi-Fi audio

equipment

with optical

audio input

010COV.book Page 17 Thursday, September 25, 2008 4:59 PM

18

GB

Viewing pictures from

connected equipment

Switch on the connected equipment, then

perform one of the following operation.

For equipment connected to the scart sockets using

a fully-wired 21-pin scart lead

Start playback on the connected equipment.

The picture from the connected equipment appears

on the screen.

For an auto-tuned VCR/ DVD recorder

In analogue mode, press PROG +/-, or the number

buttons, to select the video channel.

For other connected equipment

Press / to display a list of connected

equipment. Press

F/f to select the desired input

source, then press .

The highlighted item is automatically selected if you

do not perform any operation for two seconds after

pressing

.

If you have set an input source to "Skip" in the "AV

Preset" menu (page 27), that input source does not

appear in the list.

z

To return to normal TV mode, press DIGITAL or

ANALOG.

Additional operations

Symbol on the

screen

Description

AV1

To see the equipment connected to

A.

AV2

To see the equipment connected to

B.

~

SmartLink is a direct link between

the TV and a VCR/DVD recorder.

AV3 To see the equipment connected to

L.

HDMI 1* To see the equipment connected to

D.

HDMI 2* To see the equipment connected to

E.

If the equipment has a DVI socket,

connect the DVI socket to the

HDMI IN socket through a DVI-

HDMI adaptor interface (not

supplied), and connect the

equipment’s audio out socket to the

audio in HDMI IN socket.

HDMI 3*

To see the equipment connected to

K.

* ~

• Be sure to use only an authorized HDMI cable bearing

the HDMI logo. We recommend that you use a Sony

HDMI cable (high speed type).

• When “Control for HDMI” compatible equipment is

connected, communication with the connected

equipment is supported. Refer to page 19 to set up this

communication.

• When connecting an audio system with HDMI socket,

be sure to also connect to the HiFi socket.

Component To see the equipment connected to

C.

PC To see the equipment connected to

H.

z

It is recommended to use a PC

cable with ferrites, such as the

"Connector, D-sub 15" (ref. 1-

793-504-11, available in Sony

Service Centre) or equivalent.

To connect Do this

Headphones M Connect to the i socket to listen to

sound from the TV on headphones.

Conditional

Access Module

(CAM) I

Provides access to pay TV services.

For details, refer to the instruction

manual supplied with your CAM.

To use the CAM, remove the

“dummy” card from the CAM slot,

then turn off the TV and insert your

CAM card into the slot. When you

are not using the CAM, we

recommend that you keep the

“dummy” card in the CAM slot.

~

CAM is not supported in all countries.

Please check with your authorized

dealer.

Hi-Fi audio

equipment G

Connect to the audio output sockets

to listen to the sound from the

TV on Hi-Fi audio equipment.

DIGITAL

AUDIO OUT

(OPTICAL) F

Use an optical audio cable.

USB J Use USB memory to display photos.

To Do this

Return to normal TV

mode

Press DIGITAL or ANALOG.

Symbol on the

screen

Description

010COV.book Page 18 Thursday, September 25, 2008 4:59 PM

19

GB

Using Optional Equipment

Using the Options menu

Press OPTIONS to display the following options

when viewing pictures from connected equipment.

To view two pictures simultaneously

– PAP (Picture and Picture)

You can view two pictures (external input and

TV programme) on the screen simultaneously.

Connect an optional equipment (page 17), and

make sure that images from the equipment

appear on the screen (page 18).

~

• This function is not available for a PC input

source.

• You cannot change the size of the pictures.

• You cannot display analogue TV video in the TV

programme picture while displaying AV1, AV2 or

AV3 video in the external inputs picture.

1 Press OPTIONS.

2 Press F/f to select “PAP”, then press .

The picture from the connected equipment

is displayed on the left, and the TV

programme is displayed on the right.

3 Press the number buttons or PROG +/- to

select the TV channel.

To return to single picture mode

Press or RETURN.

z

The picture framed in green is audible. You can

switch the audible picture by pressing G/g.

To view two pictures simultaneously

– PIP (Picture in Picture)

You can view two pictures (PC input and TV

programme) on the screen simultaneously.

Connect a PC (page 17), and make sure that images

from a PC appear on the screen.

1 Press OPTIONS to display the Options

menu.

2 Press F/f to select “PIP”, then press .

The picture from the connected PC is displayed

with full size and the TV programme is displayed

on the right corner.

You can use

F/f/G/g to move the TV programme

screen position.

3 Press number buttons or PROG +/- to select

the TV channel.

To return to single picture mode

Press RETURN.

z

You can switch the audible picture by selecting “PC

Sound/TV Sound” from the Options menu.

Using BRAVIA Sync

(Control for HDMI)

The control for HDMI function enables the TV

to communicate with the connected equipment

that is compatible with the function, using

HDMI CEC (Consumer Electronics Control).

For example, by connecting Sony equipment

that is compatible with control for HDMI

(with HDMI cables), you can control them

together.

Be sure to connect the equipment correctly,

and make the necessary settings.

Control for HDMI

• Automatically turns the connected

equipment off when you turn the TV off.

• Automatically turns the TV on and

switches the input to the connected

equipment when the equipment starts to

play.

• If you turn on a connected audio system

while the TV is on, the sound output

switches from the TV speaker to the audio

system.

• Adjusts the volume (2 +/-) and mutes the

sound (%) of a connected audio system.

• You can operate the connected Sony

equipment that has the BRAVIA Sync logo

by the TV remote by pressing:

– m/N/X/M/x to operate the connected

equipment directly.

Options Description

Picture Mode (except

PC input mode)

See page 22.

Display Mode (in PC

input mode only)

See page 22.

Sound Effect See page 23.

Speaker See page 27.

PIP (in PC input

mode only)

See page 19.

PAP (except PC input

mode)

See page 19.

Auto Adjustment (in

PC input mode only)

See page 26.

Horizontal Shift (in

PC input mode only)

See page 26.

Sleep Timer (except

PC input mode)

See page 25.

Power Saving See page 24.

Continued

010COV.book Page 19 Thursday, September 25, 2008 4:59 PM

20

GB

– SYNC MENU to display the menu of the connected

HDMI equipment on the screen.

After displaying the menu, you can operate the

menu screen by using F/f/G/g and .

– OPTIONS to display “Device Control”, then select

options from “Menu”, “Options”, and “Content

List” to operate the equipment.

– Refer to the instruction manual of the equipment for

available control.

To connect the equipment that is

compatible with control for HDMI

Connect the compatible equipment and the TV

with a HDMI cable. When connecting an

audio system, be sure to also connect the

DIGITAL AUDIO OUT (OPTICAL) socket

of the TV and the audio system using an

optical audio cable. For details, see page 18.

To make the control for HDMI settings

The control for HDMI settings must be set on

both the TV side and connected equipment

side. See HDMI Set-up on page 28 for the TV

side settings. For settings on the connected

equipment, refer to the operating instructions

for that equipment.

Buttons for using optional equipment

1 m/N/X/M/x: You can operate the

BRAVIA Sync-compatible equipment that is

connected to the TV.

2 THEATRE

You can set Theatre Mode on or off. When

Theatre Mode is set to on, the optimum audio

output (if the TV is connected with an audio

system using an HDMI cable) and picture

quality for film-based contents are

automatically set.

z

If you turn the TV off, Theatre Mode is also

turned off.

3 SYNC MENU: Displays the menu of connected

HDMI equipment. While viewing other input

screens or TV programmes, “HDMI Device

Selection” is displayed when the button is

pressed.

~

• Control for HDMI (BRAVIA Sync) is only

available with the connected Sony equipment

that has the BRAVIA Sync logo or is compatible

with control for HDMI.

• Sony BRAVIA Theatre Sync Products and

Control for HDMI compatible devices from

other manufacturers may not support all

functions.

GUIDE

010COV.book Page 20 Thursday, September 25, 2008 4:59 PM

Strona jest ładowana ...

Sony KDL-40W4000 Instrukcja obsługi

Sony KDL-40W4000 Instrukcja obsługi

w innych językach

Powiązane dokumenty